Search Documents

By Fred Witt, Milton Schwartz

ESTABLISHED methods for obtaining quantitative pole figures for flat sheets1"5 can be extended to apply to thin films on a substrate. The mode of scanning the sample is exactly the same as described in the references? but consideration is given to the fact that the scattered X-ray intensities are due to both the thin film and its substrate with appropriate attenuation factors. The purpose of this paper is to describe a method to obtain the scattered intensities from the film alone for subsequent pole-figure determinations. Fig. 1 shows the four possible general positions of the film (f) and its substrate (s) with respect to the incident X-ray beam (I,). In this paper it will be assumed that the plane of the sample is normal to the plane of the diffractometer. In the diagrams the line jV is the normal to the flat sample and the line P is the trace of the diffracting crystallographic planes in the plane of the diffractometer. The angle of tilt, a, is the positive acute angle measured from the line N to the line P; if this angle is measured clockwise then a is said to be in the positive a region; if this angle is measured counterclockwise then a is said to be in the negative a region. For the reflection cases, the total scattered intensity, at the proper Bragg angle for a particular set of planes, is due to that scattered by the film Vf) and that scattered by the substrate. The beam incident on

Jan 1, 1967

Jan 1, 1927

By Thomas A. Edison, John Birkinbine

The Transactions already contain many valuable papers on the subject of ore-concentration, but with reference more to the treatment of other ores than those of iron. In this country much money, labor and thought have been devoted to the enrichment of iron-ores by roasting to drive off sulphur and carbonic acid, eliminate water, or make the ore more friable, and by washing and screening to remove the clay and sand from earthy ores. In concentrating magnetites and hematites more has been done than is generally believed; but, unfortunately, the results up to the present time have not been encouraging. On the contrary, so many attempts have proved unsatisfactory that any system of concentration is now unjustly looked upon with doubt, and the problem presented to individual mines must therefore be approached with caution. For many years the magnetites of the Adirondack region of New York State have been roasted, reduced to proper size by means of gang-stamps, and jigged on screens in water. Latterly plunger-jigs and rotary-jigs have been introduced, and in some places crushers and rolls have taken the place of stamps. In one instance in that region a plant for reducing the ore by crushers and rolls and separating it by magnetism was put up to treat a titaniferous ore; but, the titanium occurring as ilmenite, the result was unsatisfactory, and the plant is now being reconstructed at another mine, where apatite and silica are to be separated from the magnetite. A large concentrating works was erected at Negaunee, Michigan, in the Marquette region, Lake Superior, to enrich the leaner specular ores. This consisted of crushers, Cornish rolls and rotary-jigs. The results ohtained weye not satisfactory, and it has been abandoned. Another plan to treat the lean magnetites from a large dump-pile at Republic, Michigan, by means of pulverizers and water-jigs also

Jan 1, 1889

By A. H. Bromly

The small agricultural village of Santa Barbara, in the State of Guanajuato, has been the center of spasmodic tin-mining operations during recent years. The deposits, so far as I know, are unique, and a few brief notes may be of interest. Santa Barbara, about 12 miles west of San Felipe station on the Mexican National Railway, and at an elevation of 2,400 m. above sea-level, is situated in a flat valley extending east and west, and bounded north and south by broken rugged hills rising about 330 m. above the general level of the valley. Tin-mining operations have been conducted at the Queensland mine, near this village. A small concentrating-mill was erected and attempts were made to smelt the ore in reverbera-tory furnaces. The country-rock of the district for many miles is rhyolite of great thickness. There are some local variations due to differences in cooling, or subsequent alteration or impregnation; but throughout the whole district the principal constituents of the rocks remain the same, viz., free silica, orthoclase-feldspar and sanidine. The latter is especially marked. The crevices and joints of the rock are frequently filled with calcedonic and opalescent quartz. The ore-formation at the Queensland mine is of an unusual nature, consisting of cracks in the rhyolite which have been filled with clay. This phenomenon is largely developed over a width of from 80 to 100 m., in which the principal fissuring follows an approximate direction of north and south. The average dip ranges between 70 and 80 degrees. Some of the fissures hold sufficiently true for a time to afford the impression that they are due to dynamic causes, or earth-movement. This may be true of some of the north by south fissures; but considering

Jan 1, 1906

By John T. Popp, Jodi A. Rulli, Anthony T. Iannacchione

Anomalous geological features in the coal and surrounding strata of a mine in northern West Virginia have fractured and deformed an inherently weak roof rock prior to mining. Horizontal stresses, as much as six times greater than overburden related horizontal stresses, have induced cutter roof failure. This failure was distinguishable from rock deformation associated with geological anomalies because it was induced by mining. The characterization of these features has allowed for the prediction of zones of unstable roof rock and the determination of failure trends on gateroad stability. Geological anomalies included clastic dikes and a narrow zone of sandstone roof. Clastic dikes, representing intrusions of shale and claystone, were invariably accompanied by local roof rock instability, and often formed the boundaries of roof falls. Shale was the dominant roof lithology except where a small sandstone occurred in the northwest portion of the longwall mining area. The sandstone occurs in two phases: a sandstone-filled channel, 5-m- thick and 60-m-wide, which eroded and replaced the shale roof and the upper part of the coalbed; and a sheet sandstone unit which was crossbedded to interbedded with the underlying shale. Horizontal stresses are naturally relieved through the initiation of cutter roof failure. This failure may extend from a few meters to several tens of meters horizontally, and from a few centimeters to several meters vertically. Orientations of entries and crosscuts has a greater influence on the direction and total length of cutter roof failure at the rib-roof intersection than does the principal directions of the in situ horizontal stresses. Seventy-four percent of the cutter roof failures occurred along the rib-roof intersection. Orientations of cutter roof failure away from the rib- roof intersection were clustered in the north-south direction and may have been influenced by the horizontal stress field.

Jan 1, 1984

By K. J. Edmiston, R. C. Kellner

Shortly after production was begun at the Duval Sierrita concentrator in February 1970, it became evident that difficulties would be experienced in reaching the designed operating level of 72,000 stpd. Since the major restrictions to production resided in the reduction crushing system, a comprehensive program was initiated to evaluate and optimize all crusher parameters affecting production. Positive relationships were established between production rate and crusher power draught, mantle support pressure, crusher setting, and crusher throw. Other parameters evaluated were the effects of feed distribution, crusher speed, mantle and concave configuration, choke feeding, and ore type. In order to obtain maximum production, it was also imperative that the mechanical integrity of the crushers be improved. Therefore, redesign of nearly the entire crusher assemblage, including such items as the top shell, bushings, and the mantle hydraulic support system, was required. In addition, automatic control stategies were evaluated and detailed operating guidelines were established. As a result of this extensive crusher examination, the limitation on plant throughput has been shifted to the grinding section, and a monthly average production level of 86,000 stpd is currently achieved. Programs under current evaluation are aimed at further increasing capacity to exceed 90,000 stpd.

Jan 1, 1976

By V. T. Stringfield

ONE of the earliest investigations of ground water in Florida was made in 1513 when Ponce de Leon arrived at St. Augustine in search of the Fountain of Youth. The history of the development of the water resources of the State shows that the large artesian reservoir that underlies Florida was discovered in the latter part of the last century. Part of that history is given by L. C. Johnson1 who states that the first successful artesian well in Florida was drilled at St. Augustine between 1880 and 1882. After the City of Jacksonville failed to obtain a flow of artesian water at a depth of nearly 400 ft and abandoned the drilling, R. N. Ellis, City Engineer, and L. C. Johnson, using Johnson's knowledge of the geologic structure of the artesian reservoir, estimated correctly that artesian water could be obtained at a depth of about 500 ft. Thus began the development of the large artesian system in the northeastern part of the State. In 1908, the Florida Geological Survey issued its first report on the ground water of central Florida.

Jan 6, 1951

By L. C. Raymond

Valuations in the mineral industry differ from those of other enterprises because mines and oil wells have a definite life so cannot be considered a perpetuity. This requires that in any mineral-property evaluation the recovery of invested capital is necessary during the life of the property. Capital writeoffs for nonextractive industries are assumed to be continuously plowed back to sustain the operation and produce yields on the capital invested. The extractive or mineral industry, however, generally attempts to return to the investor both interest and principal during the life of a property. Normally this is done currently and the dividend includes both items. Where the mineral properly possesses large reserves and the life factor approximates a perpetuity, the return on investment is generally comparable to that of industrial stocks. The valuation of a mineral property, at best, is based on educated estimates and judgment factors. This is particularly true as it relates to estimating selling prices over a long term or assessing the quality of management. Also, it is possible to make various assumptions as to rapidity of working out the deposit, varying time for start-up of operations, varying earning rates, so as to obtain different results with the same basic facts. Thus it is not surprising that two engineers, irrespective of their abilities, may not agree exactly even when given the same facts, but their results should be close enough to be used in establishing a fair value for trading purposes. The valuation is no better than the source of basic data and the soundness of judgment factors. Fundamentally the basic principles of mineral valuation are similar for base metals, sulphur, oil, or any other mineral. Each mineral, however, requires an engineer to have a knowledge of such factors as its occurrence, distribution, mining and processing methods, and marketing problems in order to gather and analyze all the facts and data that have a bearing on the earning potential of the property. PRESENT VALUE OF A MINERAL PROPERTY In essence the present value of a mineral property is a sum of money in today's dollars that future earnings from the property are worth. It differs

Jan 1, 1964

By R. W. Stormont, F. Wald

The phase diagram of the Pseudobinary section PbTe-Fe was determined. It was found to contain a monotectic and a eutectic reaction, the latter one taking place at 14 at. pct Fe and 875° * 5°C. The solid solubility of iron in PbTe was found to be 0.3 at. pct by electronmicroProbe analysis. No solubility of PbTe was detected in iron. Slight deviations from true pseudobinary behavior were found to occur in the range of - 5 to 10 at. pct Fe. In the course of a general investigation of reactions of various metals with lead and tin telluride,' the lead telluride-iron system was reinvestigated. It had been established much earlier than iron does not chemically react with lead telluride but forms a eutectic with a melting point of 879" The eutectic composition or other related information has never been reported, but for a number of years iron has been in general use for contacting of lead telluride and lead telluride alloys for thermoelectric applications. It seems therefore desirable to clarify the exact constitution of the system to furnish a base for the long-term evaluation of bonds made between lead telluride and iron either by pressure contacting or by brazing methods. I) EXPERIMENTAL METHODS Lead telluride-iron alloys were prepared in 10-g charges, using premelted lead telluride. This material was prepared from high-purity, semiconductor-grade lead and tellurium obtained from the American Smelting and Refining Co. and described as 99.999 pct pure. The iron used was "Armco" iron; the major impurities found here were 0.02 pct C, 0.018 pct Si, and 0.015 pct Cr. All remaining impurities were less than 0.01, the total of all impurities not exceeding 0.15 pct. Charges were prepared in closed quartz arnpoules which were evacuated and in some cases backfilled with high-purity argon to retard excessive lead telluride evaporation and deposition in slightly cooler parts of the ampoule. For high iron concentrations, this can lead to total separation of the constituents, since the vapor pressure and the sublimation rate of PbTe are quite high.4 Nevertheless, since the ampoules are closed, no change in overall composition was expected and the nominal composition of all alloys was assumed to be retained. X-ray diffraction analysis, thermal analysis, and microsections were used in the evaluation of the alloys. The nature of the system was such that X-ray diffraction was not particularly helpful. It merely served to establish that at all concentrations PbTe and a! iron were in equilibrium at room temperature. Thermal analysis was carried out by taking direct temperature vs time curves on a Sargent recorder where a width of 10 in. was kept as 1 or 0.5 mv by use of an automatic bucking voltage network. Quartz ampoules with minimized dead space, coated with boron nitride and fitted with a thermocouple reentrant, were used as containers for the charge. At high temperatures and over long periods of time, boron nitride reacts with iron. For the thermal analysis runs, however, this was not significant. More significant was the fact that the vapor pressure of PbTe at some of the meas -uring temperatures apparently exceeded I atrn quite considerably. This, in some cases, caused the slightly softened quartz tubes to blow out if great care was not taken to contain them and minimize time and temperatures used. As containers pure nickel tubes were used which also served to avoid temperature gradients in the quartz ampoule. Nevertheless, the experimental difficulties at high temperatures were severe and the monotectic temperature could therefore not be determined accurately. In general, the accuracy reached by the thermal analysis setup in this case is *4"C as determined with gold, silver, and tin, under the conditions of analysis here. Inherently, the apparatus is capable of reaching accuracies better than i 1°C. Also, difficulties were encountered in microsection-ing. They were related to polishing, since it is rather difficult to avoid pulling the iron out of the weak and brittle lead telluride matrix. It proved best to follow a procedure where, after grinding to 600 grit on carborundum paper, a polish with 6 p diamond was used on nylon cloth. Finally, #3 "Buehler" alumina and an automatic polisher were used for -5 min only, to avoid relief. The best etching results were achieved with

Jan 1, 1969

By D. W. Fuerstenau, P. C. Kapur

The kinetics of green pelletization in a laboratory balling drum have been studied, using pulverized limestone as a model system. The growth characteristics of green pellets were found to be extremely sensitive to the moisture content of the material. Empirical kinetic equations, which incorporate a function of specific surface of the pellets as the criterion for growth potential, have been found to describe growth in a nucleation region and in a ball growth region. The rate constants in the kinetic equations are strongly dependent on the moisture content of the material being pelletized. Size distributions of the balls at different stages of pelletiz-ing are also discussed. In many industrial chemical processes, particulate matter can only be utilized if it is in an agglomerated form, such as pellets. Pelletizing is now widely used in iron ore technology1, and it has also been applied to a number of diverse fields such as the production of cement-kiln feed2, fertilizers3, and fluorspar4. Recently, it has been proposed to pelletize dispersion-type ceramic nuclear fuel elements5. In iron ore technology, for example, the production of agglomerates by pelletizing involves two major steps: 1) the preparation of green balls by rolling particles in a suitable balling device and 2) the firing of the green balls to form compact, strong bodies upon sintering. The critical step in a successful iron ore pelletizing operation is generally considered to be the balling operation1. In this paper, which is not concerned with the sintering of green pellets, the words green pelletizing and balling will be used interchangeably. Green pelletizing, or balling, will be defined as the process of forming larger bodies by rolling fine particles on a surface without the application of direct pressure. Two recent literature surveys6" indicate that in spite of the considerable amount of industrial pelletizing, very little is known about the fundamental principles of balling and its kinetics. The first reported research on the kinetics of pelletizing is the work of Newitt and Conway-Jones8. Using silica sands of different sizes in a batch laboratory balling drum, they found that the average green pellet diameter increased linearly with time at constant drum speed, and qualitatively the growth rate increased with moisture content. Generalized conclusions cannot be drawn from their research since the materials which they pelletized were sand and sand-silt mixtures rather than comminuted materials. Moreover, Newitt and Conway-Jones used testing sieves to estimate the size distribution of the green pellets, and this technique limited the range over which they could study the growth kinetics of the pellets. Bhrany and co-workers9 investigated the kinetics of balling iron ore fines on disk pelletizers ranging in diam from 1 to 18 ft. In their investigation, balling was carried out as a continuous operation, and growth kinetics were studied in terms of retention time of the material on the disk. Although the feed material in their study was quite coarse (the maximum size being about 1/2 in.), they also found qualitative relationships between pellet growth and water content, and feed size. In the present investigation, a number of innovations were introduced that refined the experimental measurements and established the reproducibility of balling experimentation. This enabled extension of the range of measurements to include study of agglomerate nucleation phenomena in the fractional mm size. This paper presents a detailed analysis of the nucleation and growth of green pellets in a laboratory balling drum. MATERIALS AND METHOD Pulverized limestone of specific gravity 2.72 was used as a model system in these studies. It has already been established that the balling characteristics of limestone and silica are similar to those of iron ore concentrates 2,8,10, depending on physical, rather than chemical, properties of the particles. The size distribution of the limestone was determined by a wet-dry sieving technique in the sieve range and by a sedimentation balance in the sub-sieve range. Fig. 1 presents the size distribution of the limestone used in this research. This figure shows that the material is finer than 200p (65 mesh) and that 25% of it is finer than 12. The specific surface area of this powder, as measured by BET gas adsorption methods,

Jan 1, 1964

By L. B. Harris

Continuous cyclic unloading during tensile work hardening of polycrystalline zinc at room temperature enables specimens to sustain greatly increased extension. Such enhanced ductility is associated with creep-type extension, during which the cyclic component appears to promote relaxation of internal strains. It is possible to trace the transitions from tension, through enhanced cyclic extension, to fatigue and relate the observed behavior to simpler types of deformation. DISTINCTIVE deformation behavior has been shown to occur when loading includes both cyclic and unidirectional components. For aluminum and copper extended by a sequence of progressively biased strain reversals, coffin1 observed greater fracture ductility and lower flow stresses than during monotonic tension. This may be compared with the reduction in hardness obtained from conventional fatigue softening. But fatigue softening is accompanied by enhanced fatigue life,' whereas Benham3 found that fatigue life was reduced when copper continuously extended during axial load cycling. The corresponding specimen elongation, for large cyclic load amplitudes, was greater than during normal tension. Under different conditions, Bendler and wood4 found that torsional fatigue initiated extension in copper under low tensile loads previously in equilibrium with the specimen; fatigue life was again reduced. Thus there is a type of cyclic softening which is associated with reduced fatigue life and which occurs when the cyclic loading is accompanied by a unidirectional strain component. Further, the fracture ductility or extension obtained from the unidirectional component can exceed that obtained in the absence of cyclic load. Specimen extension was not initiated by axial fatigue at small load amplitudes;3 hence Benham's work distinguishes between fatigue at large and small amplitudes, the former often being linked with unidirectional deformation because of similarities in strain Structure. The initiation of tensile extension during torsional fatigue,4 however, occurred with small amplitudes. Comparable changes in behavior have been ob- served during creep. kennedy' found that combined cyclic and creep stresses on lead at 32°C increased the rate of elongation over that for simple creep, the consequence being a reduction in creep life. It was also demonstrated that small cyclic stresses applied after creep deformation initially increased recovery, but that prolonged application produced only normal fatigue hardening. It is clear that physical properties can be changed by interaction between the cyclic and unidirectional deformations, but owing to the number of different ways in which the deformations can be combined and the large number of possible variables for each combination, trends of behavior become easily obscured. One definite conclusion is that enhanced ductility or increased extension can be obtained by cyclic action, and it is this process that has been investigated for the tensile test by measurements of the extra tensile strain produced by the addition of a cyclic tensile component. EXPERIMENTAL PROCEDURE Material. Specimens were 99.99 pct Zn wire of 1.6 and 2.0 mm diam. Mean grain diameter was 0.02 mm, sufficiently small to give a ductile necked-down fracture under all loading conditions. All experiments were conducted at an average temperature of 20°C. Normal Tension. Unidirectional tensile curves at different strain rates were obtained from an In-stron testing machine, on which load-time curves were recorded autographically, using gage lengths of 5 and 10 cm. Straining was at constant cross-head velocity, and quoted strain rates are with reference to initial specimen length. Measurements of total elongation under simple tension were also made on the tensile machine that had been modified to incorporate an added fluctuating load. Combined Tension and Rapid Cyclic Load. An electromagnetic vibrator was coupled to the elastic beam of a Hounsfield ensometer- and driven sinus-oidally from a power amplifier at frequencies from 20 to 360 cps, the flexible connecting links on the tensometer being replaced by rigid fixtures to eliminate lateral vibration in the specimen. One end of the specimen was pulled by the normal extension drive of the tensometer while the other end, fixed to the elastic beam and vibrator, was subjected to rapid oscillations of load. It was thus possible to apply cyclic load to a tensile test without altering the rate of extension of the specimen

Jan 1, 1964

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,' in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. Shape and Size of Centrifugal Liquid Crucibles When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. Types of Furnaces Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1939

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,' in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. Shape and Size of Centrifugal Liquid Crucibles When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. Types of Furnaces Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1939

By T. G. Chapman

The writer has carried on experimental work for several years with respect to the simultaneous dissolution of gold by cyanide and the adsorption of the dissolved gold on activated charcoal in ore pulps, followed by the recovery of the charcoal by flotation. The results of this experimental work have been sufficiently encouraging to suggest a new process based on the principle of simultaneous dissolution and adsorption of gold, applicable to certain ores and tailings that cannot be treated to advantage by countercurrent decantation or filtration. Applications for patents have been filed and The Dorr Company, Inc. has the exclusive right to license the use of the process. The purpose of this paper is to describe such a process, state its possible advantages and immediate field, and give some results obtained on a laboratory scale. Early Experimental Work In the early stages of the experimental work attempts were made to precipitate soluble gold from cyanide solutions with zinc and aluminum in ore pulps followed by flotation of the precipitated gold, but since the results were not promising enough to continue with these precipitants attention was directed to carbon. The first experiments with carbon comprised the addition of cyanide and alkali to the ore pulp, the addition of carbon at or near the end of the dissolving period, and the recovery of the carbon by flotation. With this method of procedure the assumption was made that carbon functioned as a precipitant of gold from cyanide solutions and as such should be added as are other precipitants, including zinc and aluminum; namely, at the end of the dissolution period. The assumption was then made that carbon functioned as an adsorbent, and that if such assumption proved to be correct, it could be added with success to the ore pulp at the time of adding the cyanide. The first experiment along this line was successful in that the feasibility of the dissolution of gold by cyanide and the simultaneous extraction of the dissolved gold by carbon in ore pulps was demonstrated, at least with respect to such treatment on a laboratory scale.

Jan 1, 1939

By H. C. Miller

THE gas-lift method of flowing oil from wells is the outstanding feature of petroleum technology today. Its forerunner, the air lift, was used successfully first, in the Baku fields of Russia, in 1899, and later in the Gulf Coast fields of Texas and Louisiana and the Kern River field of California. It is still used to a limited extent in certain oil fields. The use of compressed natural gas for lifting oil from wells has supplanted the air-lift method in a measure in those fields where a sufficient quantity of gas accompanies the oil to make the gas lift possible, or where natural gas is plentiful and inexpensive. We find therefore in California, that, natural gas is used at practically every well where a gaseous medium is employed to flow the oil. The use of natural gas has many advantages over that of air. It is possible to recover and save the gasoline from the gas that accompanied the oil to the surface. This gasoline would be wasted if air were used as the lifting medium. Also, certain proportions of air and gas form an explosive mixture that cannot be handled safely by compressors. Another advantage that gas has over air is that gas under pressure is more soluble in oil. Gas in solution in oil reduces the viscosity of the oil that is being produced and causes it to flow more readily through the. tubing and flow lines. The gas lift has made it possible to recover many thousands of barrels of oil from deep wells in California that could not have been produced otherwise. It would not have been economical, had it been mechanically possible to produce such wells as the world's deepest producing oil well (Miley Athen's No. 6, Rosecranz field, California) by any other method of pumping known today. At this well, production is obtained from between 7305 and 7591 ft. and 11 months after completion of the well, production was being maintained on the gas lift it approximately 2000 bbl. a month. The crookedness of the hole, or its diameter and depth will not prevent the successful application of gas-lift pumping when other conditions are favorable.

Jan 1, 1927

By C. A. Mitke

(Butte Meeting, August, 1913.) 1. Character of Gases which Caused Helmets to Get Out of Order. DURING September, -1911, the fire area in the Lowell mine continually increased and gases resulting from the fire came through the upcast shaft. These gases contained such a large percentage of sulphur dioxide that the men were unable to go up and down on cages, and, within a comparatively short time, repairs in the shaft were found to be necessary. Since the fire was in sulphide ores and extended into certain timbered sections, the gases contained varying amounts of SO2 CO2, and perhaps, at times, CO. The temperature in the shaft was generally about 97°, and the relative humidity from 97 to 99.5 per cent. The corrosive action of the fumes became apparent when the cables had to be changed more often than usual, the heads of lag screws .in the guides of the shaft disappeared, and the cages needed frequent repairs. It also became necessary to repair two compartments of the shaft by putting in 150 ft. of new guides between the 600 and 800 levels and lag screws in nearly all the old guides from the surface to the 800 level. 2. Ordinary Methods of Testing Helmets which were Unsatisfactory. These conditions required all work to be done by men wearing oxygen helmets. The Draeger type was tried, and was used until all repairs were completed. At first the helmets were. tested for air circulation and air tightness and the injector was tested by water gauge according to the methods recommended by the Draeger Oxygen Apparatus Co. Six arrangements, covering .these different tests, are illustrated in the catalogue and circulars of the company.

Jan 7, 1913

By Len Ramp

CHROMITE deposits in southwestern Oregon occur along definite zones or horizons in sill-like ultramafic intrusions. These horizons are here referred to as ore zones and are distinguishable only by relatively Shin and scattered, discontinuous chromite occurrences. The zones are tabular in shape but are usually folded and faulted by the intensive post-intrusion deformation the ultramafic rocks have undergone. A single zone may contain disseminated, nodular, banded, or pods of massive chromite. The typical chromite deposit is composed of a series of thin lens-shaped bodies that lie along a definite plane and generally show evidence of magmatic flow with their long dimensions aligned in the direction of flow. A body of chromite often pinches down to a narrow wisp only a fraction of an inch thick. This thin streak of chromite may point to or be connected with another body of chromite. In some deposits the orebodies have a definite rake. The depth at which chromite may be found can be predicted by its position in a folded intrusive, provided that adequate structural evidence is available. Although the ore shoots are characteristically discontinuous, there is theoretically no limit to the depth at which chromite may be found. Origin: All the chromite deposits examined in southwestern Oregon are of magmatic origin, that is, the chromite was an original constituent of the peridotite magma and became segregated in varying degree from the magma to form the ore de- posits. Examples of early, intermediate, and late magmatic chromite have been recognized in the area. Crystallization of the principal minerals (olivine, pyroxene, and chromite) was apparently near completion at the time of intrusion of the peridotite magma. The magma acted as a viscous crystal mush stringing out aggregates of pyroxene and chromite in the direction of flow. These streaky accumulations are termed schlieren.

Jan 8, 1957

By Frank Van Horn

IT is customary to ascribe two general modes of occurrence to natural gas, namely shale. gas which, as the name indicates, is found in' shale, and reservoir gas, which occurs ill sandstone, conglomerate and dolomitic limestone. Both of these types are found in the Cleveland district. The shale gas has been produced on a small scale for a long period of years, probably dating back as far as 1883. Shale gas is a low-pressure gas, small in volume with variable pressure, and is limited to no definite horizon. It is generally independent of oil, may last for a long time, and is not dependent to any great extent on the structure of the rocks. There are many such wells in the district which range from 400 to 1,840 ft. in depth, although most have been completed at about 800 ft. This indicates that the wells pass through the Cleveland and Chagrin shales into the Huron or Portage shale of the Upper Devonian. During the last 2 years great interest has developed in a deeper-seated reservoir gas. What is commonly called reservoir gas is generally a high-pressure gas occurring in large volume at a definite horizon. Oil may, or may not, be associated with the gas, and in most regions in which reservoir gas is found, the geological structure is of great importance. This type of gas occurs in all large fields such as those of West Virginia which have been supplying Cleveland until the recent discovery of local gas at great depths in commercial amounts.

Jan 1, 1917

By T. G. Chapman

The writer has carried on experimental work for several years with respect to the simultaneous dissolution of gold by cyanide and the adsorption of the dissolved gold on activated charcoal in ore pulps, followed by the recovery of the charcoal by flotation. The results of this experimental work have been sufficiently encouraging to suggest a new process based on the principle of simultaneous dissolution and adsorption of gold, applicable to certain ores and tailings that cannot be treated to advantage by countercurrent decantation or filtration. Applications for patents have been filed and The Dorr Company, Inc. has the exclusive right to license the use of the process. The purpose of this paper is to describe such a process, state its possible advantages and immediate field, and give some results obtained on a laboratory scale. Early Experimental Work In the early stages of the experimental work attempts were made to precipitate soluble gold from cyanide solutions with zinc and aluminum in ore pulps followed by flotation of the precipitated gold, but since the results were not promising enough to continue with these precipitants attention was directed to carbon. The first experiments with carbon comprised the addition of cyanide and alkali to the ore pulp, the addition of carbon at or near the end of the dissolving period, and the recovery of the carbon by flotation. With this method of procedure the assumption was made that carbon functioned as a precipitant of gold from cyanide solutions and as such should be added as are other precipitants, including zinc and aluminum; namely, at the end of the dissolution period. The assumption was then made that carbon functioned as an adsorbent, and that if such assumption proved to be correct, it could be added with success to the ore pulp at the time of adding the cyanide. The first experiment along this line was successful in that the feasibility of the dissolution of gold by cyanide and the simultaneous extraction of the dissolved gold by carbon in ore pulps was demonstrated, at least with respect to such treatment on a laboratory scale.

Jan 1, 1939

By E. H. Hamilton, H. C. Vacher

The limiting concentrations of carbon and oxygen which may CO-exist at equilibrium in liquid iron are important in determining the degree to which liquid steel may be refined before it is deoxidized. Most refining processes depend upon the oxidation of a highly carburized iron which invariably results in contaminating the steel with oxygen. The oxygen thus introduced presents many problems to the refiner, who in turn has attempted to rid the steel of this impurity by deoxidation witch elements such as manganese, silicon and aluminum. The importance of the limiting concentrations of carbon and oxygen is accentuated in view of a number of recent researches which have indicated in many instances the existence of relations between oxide inclusions and dissolved oxygen and physical properties and chemical behavior of steel. The determination of the equilibrium concentrations of carbon and oxygen existing in iron under steelmaking conditions is obviously of fundamental importance. It has been generally assumed that the product of the equilibrium concentrations of carbon and oxygen in liquid iron is a constant and that this product is directly proportional to the carbon monoxide pressure in equilibrium with the liquid iron. Hertyl.2 has computed values for this product based on open-hearth data which are all in the neighborhood of 0.01 to 0.03 (per cent. FeO X per cent. C) for temperatures in the vicinity of 1550" to 1600" C. and one atmosphere pressure. Kinzel and Egan % have attempted to determine the value of this product by exposing liquid iron to carbon monoxide at one atmosphere pressure. The value reported by them was 0.0005 at 1550" C. In order to apply certain equations to the rate of carbon elimination in the open-hearth process, Feild4 found it necessary to assume a value of 0.0102 at 1580" C. for this

Jan 1, 1931