Search Documents

By Raymond S. Weimer

Of the several characteristics of a coal that influence its suitability for use in a given piece of burning equipment, the clinkering and slagging characteristics of the ash of the coal are highly important. They determine the maximum rate at which the coal may be burned on a stoker or in pulverized form without difficulty from damage to metal parts, from erosion of refractory walls, or from stoppage of gas passages by accumulation on the tubes. They also determine the minimum rate at which a slag-tap furnace may be operated without difficulty in removal of the ash in fluid form. Need for a Better Criterion In common with other producers and users of coal, the Northern Illinois Coal Corporation has long used the available methods for the measurement of the clinkering characteristics of coal ash, chemical composition and fusion temperature of the ash, as criteria for the selection of coal that would suit the particular requirements of its customers. These two available criteria have greatly helped in the problem of selection but it is unnecessary to dwell upon the fact that they are not completely adequate for the purpose. The composition of the ash and its clinkering tendency vary widely over the company's mining area. In a certain period, some years ago, an unusual amount of severe clinkering of the ash of coal shipped made extremely acute the need for a better criterion of the clinkering that might be expected. It was also desirable that the criterion result from a reasonably rapid method, so that the clinkering characteristics of the coal would be known before shipment. Complaints on the severe clinkering of the ash came from only a fraction of the output of the mine but the occurrence of the clinkering seemed quite unpredictable. Attempts to relate the chemical composition of the ash and the fusion temperatures to the clinkering were unsuccessful. Coal from the area of the mine in which the fusion temperature of the ash was the lowest gave the least trouble from clinker-ing. Chemical analysis of the ash from that section giving the most trouble showed high contents of iron and low contents of silica, but frequently these were not greatly different from those of coals that gave little trouble from clinker. Aside from the clinkering difficulty, the coal was quite satisfactory. The ash content was normal and high rates of burning could be obtained, but again and again such severe clinkering would occur that the furnace would be shut down because of the accumulation of clinker. Examination of the clinker from the customers' plants showed that the clinkers that adhered to the grates and fouled the fuel beds were hard, flat, dense, and usually dark in color. Coal that was satisfactory gave clinkers that were softer, bulky rather than flat, of low density, and usually lighter in color.

Jan 1, 1944

By J. L. Bruce, G. W. Nicolson

ThE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydro-thern~ally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CeMent and Concrete Linings During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, howcver, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 11\2 pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with 12 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concretc and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1949

By W. G. Matteson

In 1915, the State of California passed a law of great scope and importance. This law has been in successful operation for a year and may be briefly described as an act " establishing and creating a department of the State Mining Bureau for the protection of the natural resources of petroleum and gas from waste and destrucbion through improper operations in production; providing for the inspection of petroleum and gas wells; requiring all persons operating petroleum and gas wells to make certain reports" and providing the necessary officers and assessments to carry out the provisions of the act. The statute provides for a separate department of the State Mining Bureau, under the general supervision of the State mineralogist, with a staff composed of a "state oil and gas supervisor" and four deputies. It rules that all petroleum and natural gas wells shall be drilled, operated or abandoned under the supervision of the State supervisor, who shall order such tests or remedial work as seems to him necessary to protect the interests of property owners and the general public. It also provides for a board of arbitration to consider orders given by the supervisor which are not acceptable to the well owner. Section 18 of the act, which is the provision that is directly related to this paper, requires ('the owner of any well referred to in this act to keep a careful and accurate log of the drilling of such well," and further requires that this log shall show the character and depth of the formations passed through or encountered in the drilling, particularly the location and depth of the water-bearing strata; the character of the water encountered (so far as ascertained); whether the water was shut off, and, if solat what point; that it shall show completely the amounts, kinds and size of casing used; the depth at which oil-bearing strata are encountered; the depth and character of the strata, and whether all water was successfully and permanently shut off so as to prevent percolation or penetration into the oil-bearing strata. This log is to be kept in the local office of the owner or operator, subject to the inspection of the supervisor or any of his deputies at any

Jan 1, 1917

By Richard Amberg

While the old-time melter was satisfied to bring his metal out in the desired condition, and therefore took care to have the slag liquid enough, the importance of a thorough knowledge of the slag is at present recognized in all up-to-date melting-shops. Formerly slag or cinder was considered a necessary evil, accumulating in some mysterious way wherever a man was striving to produce a clean metal. Nowadays we deliberately aim at a well-defined slag, which varies with the nature of the process and the product. In steel-making we need slag for two main purposes, namely, refining and protecting the metal. To refine metal, essentially oxidizing and reducing processes are required, while to protect the metal we need a reducing or, still better, a neutral atmosphere. Although an absolutely neutral condition between steel, on one side, and the containing vessel and the slag, on the other, is an imaginary conception, the various furnaces in use for the production of liquid steel maybe arranged with respect to the attainment of this ideal in about the following order of merit: converter, open-hearth, crucible, and electric furnace. In dealing with the subject we will find it convenient to avail ourselves of the terms of physical chemistry, which yield a simple conception of the matter and an expedient way of expression. Slag and metal at large are not mixable with each other, and we will therefore call them the two " immiscible phases," though there are certain compounds which dissolve in both phases under conditions to be considered later. Reactions be-

Jan 1, 1913

By Evan Just

Government aid, regulation, and participation in the mineral industry are not new; they date back to the time when man first adopted communal living. Even in primitive tribal life, the obtaining of arrowhead or ceramic materials, washing of gold, or mining of copper were specialized activities, under tribal sponsorship. Later, when kingdoms, dynasties, and hierarchies developed, titles to mining properties were held by the sovereign or the state, work usually being done by slaves. Title acquisition through denouncement developed in Europe in the late Middle Ages and spread to the Western Hemisphere with the Spanish and Portuguese empires. Denouncements still recognized the rights of the sovereign in the requirement to pay royalties, which practice continues in many places today. Thus, anyone who views government participation in mineral activity as "encroachment" has no historical perspective. Only in a few countries and for a few generations have private interests enjoyed the right to exploit mineral deposits without the specific consent of the sovereign or without payment of royalty. Governments and the mineral industry have been linked together by other factors. Governments have had special interest in metals and minerals as stores of value and for armaments. Spanish conquests in the New World were energized by the lure of gold and silver. Pursuit of gold led to the American seizure of California in the days of the Forty-niners. The strategic importance of minerals in our own times has called for special steps to stimulate production in national emergencies and to prevent the enemy from acquiring mineral supplies. Our export controls to deny certain minerals to unfriendly countries, purchases for Government stockpile, and subsidies for domestic production are examples. Production regulation by state governments of oil and gas has become a well established routine. In brief, the mineral industry has never lacked aid, regulation, and participation by governments. The entrepreneur who wishes to explore for or develop minerals must deal with governments in most areas before he can begin, because mineral rights are reserved by them. He can proceed through discovery and de-

Jan 1, 1964

By Everett H. Graff, Ray H. Misener

THE Sol de Oro mine is in the province of Nazca, 487 km. southeast of Lima, and 60 km. inland from the coast at an elevation of 1200 m. above sea level. From Lima the mine may be reached in 8 hr. by automobile; 472 km. from Lima to Nazca over the paved Pan-American Highway and 15 km. from Nazca to the mine over a good graveled road. The trip from Lima can also be made in 2 hr. via the Faucett Air Lines which make two stops weekly at Nazca. The [Compania] Aurifera Nazca, owning and operating the Sol de Oro mine, was organized in Lima in 1930 by a group of prominent Peruvian mining men, including Ing. Carlos Alvarez Calderon, Dr. Alfredo Alvarez Calderón, Ing. Hector Boza, Ing. Jorge Félix Remy, Ing. Eulogio Femandini, Sr. Fernando Wiese, and Sr. Julio East. The nine claims in the Sol de Oro group owned by the company comprise an area of 52 square kilometers. Development of the property was not started until 1932 and only then under adverse conditions, owing to lack of transportation facilities. Mining machinery and other supplies could be taken as far as Ica by boat and railroad, but to transport them over the 180 km. of hot, sandy desert from Ica to the mine was a problem. There was no road in those days and only a few of the most venturesome truck drivers cared to contract the hauling. Another problem the company had to face was that of securing adequate labor. The Sol de Oro is in an agricultural region, and was forced to look to the near-by cotton plantations for men. Experienced men were imported from the "sierras," but they did not stay. The men are accustomed to high altitudes and cold climate and cannot easily acclimate themselves to the hot and arid coastal region. As a consequence the company has been forced to hire the inexperienced local laborers and train them for mining. The company has established three separate camps at the Sol de Oro property. Each is approximately one kilometer from the other and connected by auto road. The upper mine camp consists of living quarters for 300 workmen and their families, a general mine office, carpenter shop and timber-framing shed, compressor house, drill-sharpening and drill-repair shop, first-aid station, time office, school and store. At the central or "empleados" camp there is a 200-ton cyanide plant, general offices, warehouse, powerhouse, shops, laboratory, hospital, school, guest house, an 18-room hotel for the single staffmen, and 12 completely modern five-room cottages for the married staff employees. At the lower camp are living quarters for 200 workmen and their families, two general stores, a school and a small theater. Below this camp, along the river, are the company wells and pumping plant supplying water for mine, mill, and camp uses.

Jan 1, 1945

By R. S. Burns, J. G. Erskine

The performance of the nine 5.5 m diameter x 6.4 m mills (18 x 21 ft) initially installed at Bougainville Copper Ltd. did not meet the laboratory and pilot plant derived design expectations as measured by Bond Work Index. During the post-commissioning period, inefficient grinding of coarse material resulted in a build-up of large circulating loads and led to reduced throughputs because of pump and cyclone overloading. Installation of larger pumps and cyclones and development of an improved circuit control philosophy alleviated materials handling problems and permitted higher tonnages to be attained. Since 1977, plant throughput has been increased by installation of three additional mills. These are 0.9 m (2.9 ft) longer than the other nine and have a higher capacity. Developments in classification and mill speed-up, together with a finer ball mill feed size and substantial improvements to mill availability (99% in 1982) have further increased plant capacity. There is a continuing emphasis on improving grinding circuit efficiency in terms of throughput/grind. Current development work includes trials of graded ball charges, different liner profiles, and assessment of scalping/regrind proposals.

Jan 1, 1985

By Bhudeo N. Sinha, Paul Dean Proctor

Heavy metal contents in stream waters, sediments, and selected aquatic algae were determined for the upper Meramec River basin, Missouri, of 3905 km2 (1508 sq mi) area and site of the proposed and controversial Meramec dam and reservoir. Six distinct drainage areas within the basin are: (1) a lightly industrialized and farm area, (2) a primitive forested- ranch area, (3) an area which includes the Northern New Lead Belt, (4) the westward drainage of an old and extensive barite mining area, (5) the main trunk of the Meramec River, and (6) short north-divide tributaries of the Meramec River. Lower Paleozoic sediments rest nonconformably upon eroded and hilly Precambrian igneous basement. This locally rises as major inliers and also makes up the St. Francois Mountains to the east. Major lead, and lesser zinc, copper, cobalt, and nickel mineralization occurs in the buried Cambrian Bonneterre dolomite. Residual barite is present along the eastern fringe of the basin and is derived from the Potosi formation. Some 62 water samples, active stream sediments (AS), bank samples (BS), and 11 selected aquatic algae samples were collected in the various drainage areas and analyzed for copper, lead, zinc, cadmium, nickel, arsenic, and mercury contents. Heavy metals in water have a maximum range of 1-120 ppb (parts per billion), and this for zinc. The AS and BS sediments have orders of magnitude greater acid leachable metal contents in the -80 mesh fraction, with lead hawing the greatest range of 11-1028 ppm. Heavy metal content of stream-algae approaches that of the sediments in which they grow. Most anomalous heavy metal accumulations occur near mining and milling activities and in the streams draining such areas. Significant distortions of the primary dispersion pattern militate against geochemical exploration for hidden ore zones, but do demonstrate the mining, milling, and smelting activities of man, and sporadic mineral occurrences in younger horizons.

Jan 1, 1980

By Craig S. Hartley

An approximate expression is obtained for the energy of a closed dislocation loop in equi1ibriu)n with a constant net stress. The result obtained is valid for loops in isotropic or anisotropzc materials provided that they are suJficiently large that the energy per unit length of a segment of the loop can be approximated by that of an infinite straight dislocation tangent to the loop. It is shown that this approximation leads to very close agreement with a more rigorous calculation of the elastic energy of a circular glide loop. The Gibbs-Wulff Form, GWF, of a dislocation is the closed planar loop which has the smallest elastic self-energy of all possible loops having the same Burgers vector and enclosing a fixed area, A.' The energy of such a loop is related to the net resolved shear stress* required to expand the loop and to the stress required to activate a Frank-Read source.223 In the following sectiorls the problem of determining the form of the GWF is discussed and an approximate method for calculating its elastic self-energy is presented. It is demonstrated that the approximations employed lead to no serious errors when applied to a calculation of the elastic energy of a circular glide loop. This method is then used to obtain a closed form expression for the energy of GWFs in isotropic and anisotropic materials. THEORY Burton, Frank, and cabrera4 have proved that the relationship of the equilibrium shape of a two-dimensional array of atoms under the influence of the Gibbs free energy associated with unit length of its boundary, G(O), is that the polar plot of G(0) vs 0 is proportional to the pedal of the GWF.* The angle 0 is measured "The pedal of the polar graph ofG(0) vs0 is the envelope of tangents to the eraph.relative to some crystallographic reference direction. The difficulty in applying this result to a closed dislocation loop arises from the self-interaction of the loop. For a dislocation the energy analogous to G(0) is a function of the total configurati~n.~ Consequently the relation which determines the GWF is an integro-differential equation rather than the simple differen- tial equation which results when G(8) is a function of 0 alone. Mitchell and smialek3 and Brown~ have used the self-stress concept introduced by ~rown' to calculate the shapes of dislocations in equilibrium with an applied stress. In this approach the glide force on an element of the dislocation loop due to the interaction of the element with the rest of the loop is equated to the glide force exerted by the local applied stress. The shape of the loop is then adjusted so that the two forces above are equal at all points on the loop. It is possible to calculate the energies of such loops by noting that, for equilibrium with an applied stress, the energy is equal to pijbiAj (summation convention) where bi is the Burgers vector, p.. is the local net stress tensor, and Ai is a vector directed perpendicular to the plane of thd loop with magnitude equal to the area of the loop. Also Brown' has calculated the energy of a hypothetical polygonal GWF using the above technique and anisotropic elasticity. However, his indicated solution for the energy in the general case of an arbitrary GWF is only slightly less involved than an iterative solution of the integrodifferential equation referred to earlier. In the present work the approximation employed by DeWit and Koehler' is used to calculate the energy of a closed loop in equilibrium with an applied stress. That is, the energy of a loop segment, ds, is approximated by the product of ds and the energy per unit length of an infinite, straight dislocation in a cylinder coaxial with the tangent to the loop at the angular position of the segment. This is known as the "line tension" approximation. The inner cutoff radius of the elastic solution defines the core radius, while the outer cutoff radius is determined by some characteristic dimension of the loop. Actually, both of these radii vary with the edge-screw character of the segment. The effective core radius changes because of the orientation dependence of the Peierls width of a dislocation,8 and the outer radius should be the radial distance from the circumference of the loop to the center of symmetry of the area enclosed by the loop.g However, since the energy varies logarithmically with the ratio of these radii while depending directly on the effective elastic constants, only the effect of the latter is considered. This approximation also neglects the self-interaction of the loop segments. For small loops this will doubtless be extremely important, but for large glide loops produced by plastic deformation the self-interaction is not nearly so important in determining the energy of the loop. This point is illustrated by the following calculation of the energy of a circular loop. Consider a circular loop of radius R which lies in the XI - x, plane of an infinite isotropic continuum and whose Burgers vector makes an angle $ with xs. The first-order solution for the elastic self-energy is:'

Jan 1, 1970

By Joseph L. Gillson

BRAZIL has had an industry based on ocean beach deposits of heavy minerals containing monazite, zircon, rutile, and ilmenite for well over 40 years, but except at the very earliest period, prior to 1906, and again during World War 11, has this industry been at all comparable in size with similar operations in other countries. Limiting factors have been neither a lack of reserves nor lack of markets (except for zircon). Although poor local transportation and shipping facilities have handicapped the development in Brazil, these conditions were perhaps equally bad (when mining operations started) in the Indian State of Travancore, and in New South Wales and Queensland, Australia, in which states the principal production of beach deposits of heavy minerals has occurred. The outstanding restraints on the Brazilian industry have been the lower quality of the Brazilian minerals, the relative small size of individual deposits that were known until recently, the lack of interest of Brazilian investors in mining ventures, and the unfavorable climate for investment of foreign capital under Brazilian mining law. The lower quality of the minerals is indicated by the fact that the Brazilian monazite carries only 5 to 6 pct Tho2*, and the ilmenite 561/2 pct TiO2, whereas the corresponding Travancore minerals carry 9 pct Tho, and 60 pct TiO, respectively. The Brazilian zircon is a dirty brown color (which can be removed readily) as compared with the gleaming whiteness of the Australian zircon. An inadequate market for the abundant zircon that will be available in any operation in Brazil is certainly a heavy restraint, since otherwise it could be an important byproduct. The oxide of zirconia, baddeleyite, that has come from Brazil is from other sources.' Since the Brazilian beach sands carry only a little rutile, that mineral has not been available as a valuable byproduct to help finance the operations. Substantial tonnages of rutile have been exported from Brazil. The sources of this mineral are stream placers and residual deposits over gneisses in the States of Goyaz, Minas Geraes, Ceara, etc. (Leonardos,' and Chambers". With these handicaps, Brazilian production from beach sands has been marginal, and there has been only one consistent producer. This is a company, originally French, which was called Companie de Franco-BrazilliCne, but, with the downfall of France in 1940, became Brazilian under the name Monazita e Ilmenita do Brasil ("Mibra"). This company has operated several deposits in the vicinity of Guara-pary, in the State of Espirito Santo. Its office and plant has been at Guarapary. Recently a company called, "Fomil" (Fomento Monazita-Ilmenita) started operations. This company was organized by the Foote Mineral Co. of Philadelphia, and such share as a foreign company can hold under Brazilian law has now been acquired by the Lindsay Light and Chemical Co. of Chicago. When the writer went to Brazil in the fall of 1940, he found that no general survey of the beaches had been made except for a thorough study of part of the area by Abreu.4 The paper by Miranda6 had not then been written. The federal Geological Survey and Department of Mines knew only of the existence of the deposits in Espirito Santo south of Vitoria, and had a hazy idea that others might be found north of Vitoria. One deposit in Bala was known in Rio, but the larger one at Guaratiba was not known, although a Frenchman had prospected

Jan 1, 1951

By Joseph L. Gillson

BRAZIL has had an industry based on ocean beach deposits of heavy minerals containing monazite, zircon, rutile, and ilmenite for well over 40 years, but except at the very earliest period, prior to 1906, and again during World War 11, has this industry been at all comparable in size with similar operations in other countries. Limiting factors have been neither a lack of reserves nor lack of markets (except for zircon). Although poor local transportation and shipping facilities have handicapped the development in Brazil, these conditions were perhaps equally bad (when mining operations started) in the Indian State of Travancore, and in New South Wales and Queensland, Australia, in which states the principal production of beach deposits of heavy minerals has occurred. The outstanding restraints on the Brazilian industry have been the lower quality of the Brazilian minerals, the relative small size of individual deposits that were known until recently, the lack of interest of Brazilian investors in mining ventures, and the unfavorable climate for investment of foreign capital under Brazilian mining law. The lower quality of the minerals is indicated by the fact that the Brazilian monazite carries only 5 to 6 pct Tho2*, and the ilmenite 561/2 pct TiO2, whereas the corresponding Travancore minerals carry 9 pct Tho, and 60 pct TiO, respectively. The Brazilian zircon is a dirty brown color (which can be removed readily) as compared with the gleaming whiteness of the Australian zircon. An inadequate market for the abundant zircon that will be available in any operation in Brazil is certainly a heavy restraint, since otherwise it could be an important byproduct. The oxide of zirconia, baddeleyite, that has come from Brazil is from other sources.' Since the Brazilian beach sands carry only a little rutile, that mineral has not been available as a valuable byproduct to help finance the operations. Substantial tonnages of rutile have been exported from Brazil. The sources of this mineral are stream placers and residual deposits over gneisses in the States of Goyaz, Minas Geraes, Ceara, etc. (Leonardos,' and Chambers". With these handicaps, Brazilian production from beach sands has been marginal, and there has been only one consistent producer. This is a company, originally French, which was called Companie de Franco-BrazilliCne, but, with the downfall of France in 1940, became Brazilian under the name Monazita e Ilmenita do Brasil ("Mibra"). This company has operated several deposits in the vicinity of Guara-pary, in the State of Espirito Santo. Its office and plant has been at Guarapary. Recently a company called, "Fomil" (Fomento Monazita-Ilmenita) started operations. This company was organized by the Foote Mineral Co. of Philadelphia, and such share as a foreign company can hold under Brazilian law has now been acquired by the Lindsay Light and Chemical Co. of Chicago. When the writer went to Brazil in the fall of 1940, he found that no general survey of the beaches had been made except for a thorough study of part of the area by Abreu.4 The paper by Miranda6 had not then been written. The federal Geological Survey and Department of Mines knew only of the existence of the deposits in Espirito Santo south of Vitoria, and had a hazy idea that others might be found north of Vitoria. One deposit in Bala was known in Rio, but the larger one at Guaratiba was not known, although a Frenchman had prospected

Jan 1, 1951

By J. S. Aronofsky

The results of polentiometric model studies and numerical computations are described. The purpose of these studies was to determine the influence of the mobility ratio on flooding efficiencies during water encroachment in petroleum reservoirs, in systems of regular well geometry. The direct line drive well pattern having relative spacing distances of one and one-half to one was investigated for water to oil mobility ratios of 10. 1. and 0.1. The results of these studies indicate that the pattern Sweep efficiency i.; very dependent upon the mobility ratio. INTRODUCTION The almost universal occurrence of water in the immediate neighborhood of oil-hearing sands lends considerable emphasis to the desirability of having a rational analysis of water encroachment into petroleum reservoirs. This problem has 1)become increasingly important with the accelerated use of water injection for secondary recovery operations. The water encroachment problem has been studied from both the theoretical and experimental viewpoints by Muskat.' He has formulated, in a precise manner, differential equations to express flow in a water encroachment system, and rigorous analytical solutions have been developed for the linear, radial, and spherical cases.' However, it becomes exceedingly difficult to solve the encroachment problem rigorously for any general two-dimensional system in which the shape of the two-fluid interface is not immediately evident from the geometry of the system. The difficulty lies in the fart that a rigorous analytical solution requires that the shape of the two-fluid interface be known simultaneously with its instantaneous posititon and with the pressure distribution on both sides of the interface. Although this paper concerns the study of the two-fluid system of oil and water. the methods described in the paper are generally applicable to other systems of incompressible and immiscible fluids in which the displacing fluid sweep-the displaced fluid down to a residual value. In each region it is assumed there is only one mobile fluid and its mobility is constant throughout the region. The Same procedure. with minor alteration, is applicable for gas injection systems provided the assumption can be made that both the displaced and displacing gases can be described by steady state formulas. For the particular two-fluid problem considered in this paper, there is a relative permeability. K, and a viscosity. p. associated with the water zone, and a different permeability and viscosity associated with the oil zone. The K/p (mobility value associated with a particular volume element of the porous medium. at any instant of time. will depend upon whether the element is ahead of. or behind the advancing interface. It is assumed that all volume elements ahead of the interface are characterized by the K/p value for oil, while all the elements behind the interface are characterized by the K/p value for water. That is. the K/p value in the oil zone is constant throughout the oil zone. and the K/p value in the water zone is also constant but different from the value in the oil zone. The symbols are defined at the end of the paper. The well pattern chosen for initial study is the direct line drive; the swept-out area at breakthrough was determined by two different methods which are described in the section on theory. These are: 1. Potentiometric analyzer 2. Numerical computation The use of the potentiometric analyzer for studying water flooding problems is adequately described in the literature, particularly for cases where the mobility in the water zone is assumed equal to the mobility in the oil zone." ' 5

Jan 1, 1952

By M. A. Torcaso, P. Raimondi

To study mass transport in systems simulating oil recovery processes, different porous media were saturated with a mobile (carrier phase) and a stationary phase. Slugs of carrier phase containing a small amount of solute were displaced with pure carrier phase. By analogy to the chromato-graphic processes, the velocity of the solute can be predicted from a knowledge of the partition coefficient and the saturation provided that equilibrium between the two phases exists. Equilibrium was found to exist for different porous media, solutes and rates. The conditions were varied over the range normally encountered in the laboratory and in the field. The longitudinal dispersion of a solute undergoing interphase mass transfer was also investigated. INTRODUCTION The production of hydrocarbons by gas cycling, enriched gas drive and C02 or alcohol displacement involves, among other factors, relative motion between two phases and compounds, hereafter called solute, which are soluble in both phases. The solute is carried forward by the faster flowing phase at a lower velocity than the average velocity of that phase. Retardation of the solute is caused by chromatographic absorption and desorption in the slower flowing phase and by the degree of departure from equilibrium. At equilibrium the concentration of solute in the two phases can be related by the equation* CSw = K Cso ,............(1) where C, and C are the concentration of solute in the aqueous and oleic phases respectively and K is the equilibrium ratio, or partition coefficient. Displacement theories must contain an explicit assumption with regard to equilibrium, i.e., whether the compositions can be related by Eq. 1. The existance of equilibrium depends, in general, on the relative velocity between the phases. Unfortunately, other factors such as gravity segregation and viscous fingering, also depend on velocity. For this reason, whenever effects of rate on displacement were observed,2-4 it was practically impossible to discern what caused them — lack of equilibrium or the factors mentioned above. Equilibrium between phases has been the subject of extensive studies in fields such as extraction or chroma to graphy. It has received only small attention in flow through the type of porous media encountered in oil production.5 For this reason a method was developed which makes it possible to study the movement of a solute as it is affected by rate, type of porous media, partition coefficient and carrier phase, but in the absence of segregation or fingering. The information obtained enables one to determine when the assumption of equilibrium can be made. Briefly, the method consists of (1) saturating the core with a mobile and an immobile phase, (2) injecting a slug made up of the same fluid as the mobile phase and a small concentration of mutually soluble solute, (3) measuring the lag and the peak height of the slug at arrival and (4) correlating these variables with fluid properties such as partition coefficient and mixing constants of the medium. PROPOSED MECHANISM The principles of chromatography are combined with the equation of longitudinal mixing to predict the velocity of a solute slug compared to the bulk velocity and the peak height of a slug.6-9 The equation so obtained is valid under equilibrium conditions only. Therefore, a comparison between experimental and predicted results will give a measure of departure from equilibrium. This work was done with either the oleic or the aqueous phase being immobile. For simplicity, the following development is based on the case where the oleic phase is immobile. However, the treatment is the same in either case.

Jan 1, 1966

By T. E. Scott, D. H. Sherman, C. V. Owen

Mechanical properties and optical metallographic characteristics of vanadium containing 53 ppm (wt) H were investigated from, 77° to 298°K. A sharp ductile to brittle transition induced by the presence of hydrogen was observed between 238° and 223°K and a mar-tensitically formed hydride appeared at 200°K. While there appears to be a subtle relationship between the hydride formation and the ductile-brittle transition, it was concluded that the hydride per se was not sufficietzt to cause the severe em brittletnent. On the basis of the metallographic experiments and the results of a Petch analysis it is suggested that the mechanism of the embrittlement involves a reduction of the true surface energy, or cohesion, of the uanadiunz. THAT hydrogen can severely embrittle vanadium is well-documented;'-5 however, the mechanism by which hydrogen induces the observed embrittlement has not been established. It is not known whether the embrittlement of vanadium is caused by the formation of vanadium hydride or by a more subtle role of hydrogen. Until very recently6>' the solid solubility of hydrogen in vanadium at temperatures in the,range of the embrittlement was not known to a useful accuracy. In general, a severe embrittlement of the type produced by the presence of hydrogen in vanadium can be caused by changes in either of two properties of a metal. Either the yield stress of the metal is raised to the extent that plastic deformation at the tip of a crack cannot occur or the cohesive properties of the metal are reduced, at least locally, to the point at which cleavage is the natural response to applied loads. Of course a combination of these is possible. It is not known which of these properties of vanadium is influenced most by the addition of hydrogen. The purpose of this investigation was to determine the role of hydrogen in the embrittlement of vanadium. Accordingly, the solubility of hydrogen in vanadium in the temperature range where embrittlement is most severe was determined, the appearance of vanadium hydride was examined in relation to the initial ductile to brittle transition temperature, and an attempt was made to evaluate the effect of hydrogen on the yield stress and cohesive properties of vanadium. MATERIAL AND PROCEDURES Sample Preparation. The vanadium used in this investigation was prepared by the iodide refining process described by Carlson and owen.' Three ingots, 3 in. diam by 6 in. long, were cold-swaged to 0.096 in. diam, cut into short lengths, and then arc-melted under purified argon into one ingot. This process was repeated to insure a uniform composition in the final ingot. Chemical analysis of the metal is given in Table I. On the basis of work of Loria et a/ .' the following sequence of treatments was performed in order to obtain a uniform equiaxed ultimate grain structure: a) cold swage q-in.-diam ingot to 0.230 in. diam; b) anneal 6 hr at 1000°C in vacuum; c) by cold swaging reduce 81 pct in area in three steps: 0.230 to 0.187 in. diam, 0.187 to 0.150 in. diam, 0.150 to 0.096 in. diam. This sequence provided the desired grain structure after subsequent annealing treatments. Because annealing in evacuated quartz capsules resulted in contamination by oxygen, all anneals in this investigation were performed in a 304 stainless-steel chamber under a dynamic vacuum of 10- I Torr with the vanadium wrapped in tantalum foil. Prior to all annealing treatments the wires were electropolished for 1 min at 16°C in an 80 pct methanol-20 pct sul-furic acid electrolyte at 12.5 v. Following the final reduction the 0.096-in.-diam wire was cut into 2-in. lengths. A 1-in. gage section was reduced to 0.090 in. diam by electropolishing as above. Five different grain sizes were obtained by annealing the 2-in. samples at different temperatures for 8 hr to insure uniform grain size and residual hydrogen removal. The annealing temperatures used and the resulting grain sizes are given in Table 11. The final step in sample preparation was to charge half of the specimens of each grain size with hydro-

Jan 1, 1969

Prospecting methods used in Tennessee have gradually improved with the years, as required by depletion of the easily accessible and shallow deposits and the universal trend toward mechanization, and as necessitated by exploring deeper beds, often occurring under limestone and flinty overburden. In the early days it was a very simple matter to dig pits by hand, using a plentiful supply of local farm labor to expose relatively shallow deposits of "brown rock" under shallow clayey overburden that would stand up without timbering. Visual inspection of the exposed phosphate and expert judgment of the "grade" analysis, aided by a "biting" test to reveal presence of unwanted silica, furnished most of the information required. All this might be helped by a few samples sent to the local chemist† who supplemented his income by judicious trading or tanning a few bear skins. The extra curricula activities did not affect the accuracy of the analysis which hold up even under present day standards. Some shot and core drilling was done in Hickman County, mostly for the limestone-like blue Phosphate deposits. The next step was the use of a 4-in. posthole auger, hand operated as described by Guenther, followed by a completely mechanized rig, as described by Pickard. Both these methods are practically adapted to the prospecting of the relatively soft brown rock deposits at moderate depths of clay overburden. For prospecting in areas of deeper overburden, such as are often found in Hickman County, up to 150 or even 200-ft depths, a modified core-drilling method is described by Guenther. Johnston describes a special diamond-drilling technique, developed by TVA, to penetrate flint horizons, which was adopted by the International Minerals in chemical corporation to prospect in Hickman County where deposits had previously been prospected at considerable expense and with difficulty, by small, temporary, hand-dug shafts.

Jan 1, 1948

Prospecting methods used in Tennessee have gradually improved with the years, as required by depletion of the easily accessible and shallow deposits and the universal trend toward mechanization, and as necessitated by exploring deeper beds, often occurring under limestone and flinty overburden. In the early days it was a very simple matter to dig pits by hand, using a plentiful supply of local farm labor to expose relatively shallow deposits of "brown rock" under shallow clayey overburden that would stand up without timbering. Visual inspection of the exposed phosphate and expert judgment of the "grade" analysis, aided by a "biting" test to reveal presence of unwanted silica, furnished most of the information required. All this might be helped by a few samples sent to the local chemist† who supplemented his income by judicious trading or tanning a few bear skins. The extra curricula activities did not affect the accuracy of the analysis which hold up even under present day standards. Some shot and core drilling was done in Hickman County, mostly for the limestone-like blue Phosphate deposits. The next step was the use of a 4-in. posthole auger, hand operated as described by Guenther, followed by a completely mechanized rig, as described by Pickard. Both these methods are practically adapted to the prospecting of the relatively soft brown rock deposits at moderate depths of clay overburden. For prospecting in areas of deeper overburden, such as are often found in Hickman County, up to 150 or even 200-ft depths, a modified core-drilling method is described by Guenther. Johnston describes a special diamond-drilling technique, developed by TVA, to penetrate flint horizons, which was adopted by the International Minerals in chemical corporation to prospect in Hickman County where deposits had previously been prospected at considerable expense and with difficulty, by small, temporary, hand-dug shafts.

Jan 1, 1948

By J. Fred Johnson

COROMANT is the trade name of the alloy-steel drill rod tipped with a chisel-type tungsten-carbide bit manufactured by Sandvik Steel Works Co., Ltd. Other names, such as Swedish or air-leg method of drilling, are used in various localities. Coromant drilling in Sweden was the natural sequence of the adaptation of tungsten-carbide inserts to the already established routine of drilling. By the middle thirties the percussion drill had reached practically its highest attainable efficiency as a drilling machine. Since then improvement has been in metallurgy of component parts to increase life or lessen weight, in the development of pneumatic and automatic feeds, in the use of jumbos to more quickly and easily handle machines, and in changes in drill rods and bits. By 1937, drilling in the United States and Canada was done by relatively heavy mounted drifters with positive hand or automatic feeds. In Sweden, on the other hand, emphasis had been placed on light equipment and drifting was done with pneumatic bars and reverse-feed stopers. In 1938, one of the most prominent American drill manufacturers developed an air-leg for successfully drilling the extremely variable but relatively soft iron ores of some of the northern Michigan mines. Also in 1938, a comparative Swedish test, also in soft iron ore, of a 50-lb jackhammer mounted on an air-leg, against a 100-lb reverse-feed drifter on a pneumatic bar, showed the net drilling time was increased by the air-leg set-up from 51 to 71 pct, in drilling 6-ft rounds in a 6 1/2x6 1/2 ft drift. Miners were becoming scarce in Sweden even at that time and, since the lighter equipment made the work easier and more attractive, the airleg was then made use of in some types of soft rock. In 1940, for instance, a large tunnel for a hydroelectric plant was driven with this equipment. By 1943, when tungsten-carbide inserts came into the picture in Sweden, a great many of the kinks in percussion drilling with this hard-metal had been worked out in Germany under the stress of war conditions. However, only 10 pct of the drilling machines manufactured in Sweden were jackhammers for use on air-legs and only the one manufacturer made air-legs in the United States. American practice had largely supplanted integral forging of drill bits by the detachable steel bit. Canada and South Africa were using the one-pass throwaway bit but Sweden was still using the same old integral forged bit. After a long study of the trend toward simplicity

Jan 1, 1952

By R. J. Marcotte, C. T. Eddy, R. J. Smith

The objectives of the investigation herein reported were to determine: (I) the S-curves for certain selected cast steels, (2) whether or not the published S-curves for wrought steels are satisfactory for use on cast steels of similar composition, and (3) to prepare hardenability curves of the selected cast steels. In order to make the final comparisons between cast and wrought steel more completely tangible, it was deemed advisable not only to determine S-curves for the steels submitted in the cast condition but also to roll some of the cast-steel test bars and determine comparison S-curves on such wrought material. This procedure eliminates the composition variable and makes it possible to reveal the differences resulting from plastic deformation of the cast structure in addition to providing the comparison with published data on wrought steels. Cast Steels The cast steels selected for the preparation of S-curves, or time-temperature transformation curves, were similar to S.A.E. series 1030, 2330, 4130 and 4330. Of these the 1030 was supplied by The Crucible Steel Casting Co., Cleveland, Ohio, and the other three by The Sawbrook Steel Castings Co., Lockland, Ohio. The steels were furnished in the as-cast condition. The manufacturers supplied the chemical analyses and the properties that could be obtained in the heat-treated condition—all of which is summarized in Table I. The metallographic and dilatometric procedures and equipment were in general standard. The specific technique employed was described in a report of the Steel

Jan 1, 1945

By George A. Lamb

AMONG the main interesting developments in the coal market have been the changes that have taken place between the consumer groups. Important signs of these changes began to appear many years ago, but in a modest way, and were apparent only to the few fuel experts making broad statistical determinations. It is doubtful, however, that any of these experts appreciated the significance of their early findings, and perhaps none had the imagination to consider how extensive these changes might be eventually with respect to solid fuels sales and distribution. (Reference here will be principally to bituminous coal.) Railroad Fuel Major changes in coal use did become pronounced after World War II, and it did not take an expert to see what was taking place and how serious the impact was likely to be. First, was the case of the steam and diesel locomotives. The railroads had been considered the best coal customers; they were steady and large purchasers and usually paid a better price than most others. Railroad fuel provided the basic mine realization and it often was the source for operating cash during general market slumps. It was the outlet for 20 pct of the bituminous coal production, as much as 110 million tons in 1946.

Jan 2, 1957

By P. A. Boeck

(San Francisco Meeting, September, 1915) THE thermal insulation of high-temperature equipment for industrial purposes is a subject that has not received from engineers and designers the attention its importance deserves. This may be attributed to a number of causes: In the first place, heat flow is a rather difficult factor to measure under the working conditions of an industrial furnace, and until the comparatively recent introduction into certain operations of the heat balance sheet, with a systematic attempt to account for the discrepancies in the totals, the various causes of heat losses and the reasons for their existence were not brought to light. Moreover, such rapid advancement and radical changes in the design of equipment, especially in metallurgical lines, have occurred that practice has apparently outdistanced the theory of design. In the modern tendency toward greatly increased size of units, effort has seemingly been made to utilize the heat of fuel gases without proper. attention having been paid to conserving heat energy and confining it strictly to the points of maximum activity. The systematic study of the thermal properties of structural materials, which is being carried out by various government bureaus and also by a number of technical societies, is forming the basis for more intelligent and consistent work in the economically important subject of prevention of fuel waste.

Jan 8, 1915