Search Documents

By W. J. Keep

Almost without exception, writers on the subject say that sulphur in cast-iron will cause it to be white, and is in every way injurious. All founders believe that a small amount of sulphur in the fuel will work great damage, and that if any castings crack, or if anything out of the general run occurs, it may be charged to sulphur in the fuel. Fuel rarely contains more than 1 per cent. of sulphur, and if this can produce so marked an effect, one would suppose it an easy matter to introduce sulphur into cast-iron, so as to produce castings containing different desired percentages of sulphur. We have be-

Jan 1, 1894

By Ottokar Hofmann

In tank-lixiviation, the extraction of the silver from chloridized ore by solutions of hyposulphite salts is performed by filtration. The ore-particles are kept stationary, while the solvent moves down through the mass of ore. The quickness of extraction, other conditions alike, is in direct proportion to the rapidity of the movement of the solvent through the ore. The solution, if left in contact with the ore without moving, displays but very little solving energy. If the filtration is interrupted for ten or twelve hours, and thus solution and ore are left in complete contact for that length of time, it mill be found that, when filtration is started again, the outflowing solution is but very little more saturated with silver than it was at the time of interruption, and that the ten or twelve hours were almost a perfect loss in the total time of extraction. Notwithstanding the long contact, the solution had not become saturated with silver chloride to its full solving capacity. A rapid movement of the solvent through the ore is essential to a quick extraction. This fact is well known ; and the endeavor of leachers has been to hasten extraction by increasing the rate of filtration. Siphons, vacuumpumps and other devices have been used with more or less success; but none of them have given full satisfaction. I have found that, if chloridized ore is brought into rapid contact with a proper volume of moving sodium hyposulphite solution, the silver chloride contained in the ore dissolves almost instantly, and that it is rather the volume of the solvent than its concentrated state which produces this effect. Such favorable conditions cannot be attained in tanks. The rapidity with which a certain volume of the solvent can be brought into contact with the ore-particles is limited by the speed with which the solution descends through the ore; and thus the leaching-time in tanks cannot be shortened beyond the limit set by the filteringcapacity of the ore. In a trough, however, these favorable conditions can be attained by gradually introducing the ore into the moving stream of the solvent. The ore can thus be brought into

Jan 1, 1888

By John Sherbourne

Much valuable scientific research has been performed in recent years on the subject of phase behavior of hydrocarbons. ? 1-11 Engineers employed in petroleum production are interesting themselves in this work as well as in methods of applying the fundamental data available to the solution of their various problems. Recently a number of papers have been published in which applica-tions of phase behavior have been made to specific cases pertaining to critical phenomena.)12-16 Little effort, however, has been made in the literature to show the relation between changes occurring in the critical region and the more common phase behavior, therefore it is believed that a presentation of the fundamentals of phase behavior with reference to hydrocarbons is timely. Study of phase behavior is not new. In the metallurgical field, knowledge of heterogeneous equilibria has advanced tremendously, particularly with reference to solid-solid and solid-liquid behavior. Much is known about vapor-liquid equilibria too, but few engineers are familiar with this subject. ?

Jan 1, 1940

By D. L. McCain

Slurry transportation of coarse coal from the mining face to the preparation plant has proved successful in a West Virginia underground mine. Coal has been pumped from the mining section for several months. The system is currently being provided with the flexible link to the face to allow for continuous transportation. Some future plans for coal mines and projections for broader applications of the transportation method are given.

Jan 1, 1976

By Jim D. Mote, Eugenia M. Howard, Willis L. Barmore, John E. Dorn

The effect of stress and temperature on the creep rate of Ag-33 at. pct A1 and Ag-33 at. pct Al-1 at. pct Zn for prismatic slip was determined over a range of temperatures from 440º to 700°K. The alloys exhibited a brief initial inverted transient creep over which the creep rate increased slightly to a steady-state value which depended only on the stress and temperature, regardless of the previous strain history. The steady-state creep rates were found to be given by: where the activation energy is independent of the stress and strain and agrees fairly well with that estimated for diffusion. The observed creep behavior was shown to be in qualitative agreement with a model based on the stress-induced local disordering in the vicinity of a dislocation. OVER the past fifteen years, considerable progress has been made in correlating the experimen-entally observed plastic behavior of pure metals over each temperature range with one or more of a series of theoretical strain-rate controlling dislocation mechanisms. Despite the current interest in the plastic behavior of intermediate phases and inter metallic compounds, however, very little has been done in identifying the operative dislocation mechanisms in these materials. It is anticipated that the plastic behavior of intermediate phases can be rationalized in terms of the same dislocation mechanisms that are appropriate to pure metals and a solid solutions, provided the additional complexities arising from crystal structure, bonding, long-range order, short-range order, and defect lattices are taken into account. As part of a more extensive investigation on the plastic behavior of intermediate phases, Mote, Tanaka, and Dorn1 recently reported on the effect of temperature on the yield strength for prismatic slip in the hexagonal Ag-33 at. pct A1 intermediate phase as recorded in Fig. 1: Over Region I the deformation was observed to take place as a result of the thermally-activated Peierls mechanism, and over Region II the athermal disordering mechanism applied. The experimental data at that time, however, were not sufficiently extensive to identify the thermally activated mechanisms operative over Region III. It is the purpose of this investigation to attempt to identify the mechanisms that are operative over this high-temperature region. It will be shown that the same mechanism operates all over Region Ill, although the activation energy for this mechanism is in good agreement with that for diffusion, the process cannot be attributed either to the motion of jogged screw dislocations or the climb of edge dislocations. The results, however, are in good qualitative agreement with stress-induced disordering localized at dislocations. EXPERIMENTAL PROCEDURE The alloys studied in this investigation were prepared from silver, aluminum, and zinc (each of purity greater than 99.995 pet) by induction melting under an argon atmosphere and chill casting in a copper mold. Rectangular bar single crystal specimens (1/4 by 1/8 in. in cross-sect ion) of Ag-33 at. pct Al were grown in vacuum by a modified Bridgman technique. Similar Ag-33 at. pct Zn specimens were produced by an identical technique employing an argon atmosphere. The specimens were so oriented that the angle 90-Xo between the tensile axis and the normal to the prismatic plane and the angle A, between the tensile axis and the slip direction were 45 ± 1 deg. The effect of a change in temperature on the creep rate and a change in stress on the creep rate were determined over the temperature range

Jan 1, 1963

By W. W. Coffeen, K. E. Doud

A singular mineral extraction and processing operation is conducted by Metal & Thermit Corp. in Hanover County, Va. The mine presently produces aplite rock, rutile and ilmenite. The deposit lies in the piedmont plain about 25 miles northwest of Richmond. It first drew attention as a result of discovery of float rutile on the surface about 1910. About seven years prior to this, Metal & Thermit through a subsidiary. American Rutile Co., had begun producing rutile'and ilmenite from a deposit in Nebon County, near Piney River, where aplite rock and ilmenite are mined today. Because of the interest in titanium minerals and the similarity of the new deposit to the Nelson County deposit, Metal & Thermit became interested and eventually acquired the Hanover County deposit.

Jan 10, 1962

By Frederick T. Fischer

The New Jersey Zinc Company began a program of exploration in Middle Tennessee in 1964. The target horizon of the exploration project has been the Knox Dolomite which is a low-yield aquifer over nearly the entire Central Basin of Tennessee (1). With the exception of a few hundred acres in the Wells Creek and Flynn Creek disturbances (astroblemes?), the Knox Dolomite in Middle Tennessee is known only in subsurface. In January of 1969, New Jersey Zinc announced the discovery of a major zinc deposit near Elmwood, southeast of Carthage. This is on the northeastern flank of the Nashville Dome where the nearly flat-lying beds have an average eastward slope of about 50 feet per mile. The anticipated development of a mining situation has emphasized the significance of hydrologic relationships in the region as a whole and especially in the Elmwood area. These relationships affect several areas of concern which ma be generally grouped into two broad classes; i. e. , (1) Problems of a Public Nature - involving the prevention of the contamination of potable aquifers, the prevention of the contamination of surface waters, the prevention of the capture of presently utilized water, etc.; and (2) Problems of Mining Economics - involving pumping capacity and costs, the possible need for equipment of special composition, underground environmental conditions, etc. Exploration drilling in Middle Tennessee has contributed additional information about the Knox aquifer and

Jan 1, 1970

By F. W. Jessen, N. Lamont

The effect of an existing fracture or joint plane, which may exist in a rock, on the extension of a hydraulically induced fracture through the rock has been investigated in the laboratory. By use of a series of models made from various outcrop rocks, the width and orientation of existing fractures do not alter the extension or direction of the hydraulic fracture. The results, which conform quite well with the Grifith theory of failure, are illustrated by a series of photographs of the various models. INTRODUCTION The process of hydraulic fracturing has been widely used in the oil industry since its introduction in 1948 and has made possible the production of many reservoirs which would have been uneconomical prior to this process. Numerous studies of the mechanics of the process2-h nd of the effects of oriented fractures on recovery'.' have appeared in the literature. The increased recoveries led to attempts to predict the orientation of hydraulic fractures at the wellbore and to the development of methods to control this orientation. Field tests have been devised"." which indicate the validity of theoretical predictions of fracture orientation at the borehole. The direction of extension of hydraulic fractures from the borehole has not received much attention since most studies have predicted, at least implicitly, that a fracture will continue in the same plane unless a change of state of stress in the rock occurs. Since such predictions are based on the assumption of rock homogeneity, the effects of rock heterogeneities are left unknown. Most sedimentary rocks are composed of layers which reflect the changing depositional conditions of geological time. In addition, the more competent rocks frequently are fractured and jointed as the result of structural deformations or tectonic movements. Evidence of such joint systems exists in many surface outcrops, and it can be assumed that similar systems occur in many subsurface rocks, although the individual joints may be rather tightly closed due to overburden forces. This paper investigates the effect that an existing fracture in a rock would have on the direction or orientation of an extending or advancing hydraulic fracture when it intersects the existing fracture. The study was conducted on small rock models under triaxial stress conditions. The results indicate that an existing fracture will have little effect on the hydraulic fracture. THE MODEL STUDY The rock model represents an elemental portion of the earth containing an existing fracture which is located at some distance from a borehole from which hydraulic fracture is being extended. A generalized view of a model is presented in Fig. 1. The models were constructed from cement blocks and natural rocks. The various materials tested and some of the physical properties are listed in Table 1. The rocks were cut into rectangular blocks with dimensions of 11/2 X3Y2 X4 to 8 in. An initial slot was cut into the end face of each block along the longitudinal axis normal to the top face. The slot was filled with plastic aluminum along its outer edge to a depth of 1/16 in. A hole of 3/8-in. diameter was drilled into the sealed slot at the center of the end face to serve as an entry port for the fracturing fluid. Existing fractures of various types were simulated in the models. A "hairline" fracture with essentially zero width was created by cutting the model into two parts with a diamond saw and replacing the two parts together along the cut. A finite-width fracture was created by placing a layer of sand grains between the two faces of the cut just described (see Fig. 12). A large open fracture (similar, perhaps, to a vug) was created by cutting the model in two parts and removing a portion of the downstream block to a depth of % in. See Fig. 13. For a fourth

By S. R. Zimmerley, S. F. Ravitz

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine.

Jan 1, 1950

By Joseph N. Morrison

A comprehensive solution is offered to the problem of dust emissions at belt conveyor transfer points. Details of enclosure design are discussed and a straightforward procedure for calculating required dust control exhaust volume is presented. Many design variables are taken into account which heretofore have been commonly ignored or inadequately considered. These include belt widths, belt speeds. enclosure openings, material flow rate, material bulk densities, material lump sizes, height of material fall, material temperature, and ambient air temperature. All of these questions are handled by means of a "fill-in-the-blanks" type of calculation form, permitting quick, reliable solutions by relative "non-experts."

Jan 1, 1972

By Henry Morris

AS STATED last year, in a similar review by David White and the author, any review of the petroleum industry purporting to cover such a wide field can only mention the principal facts. This incompleteness is necessitated not only by the limitations of space, but by the delay in receiving detailed information. The principal feature of the year, in Europe, was a material increase in the consumption of petroleum products, and a notable decline in prices. Although there we relative increases in production in Roumania and Poland, the total did not by any means keep pace with the increase in consumption, which, as usual, was supplied "from America and both the Near and Far East. The interest in Asiatic production, as usual, centers around the Persian fields, which, according to the annual report of the Anglo-Persian Oil Co. published at the close of last year, it was estimated would amount to 3,775,000 tons by the close of the fiscal year, March 1, 1924. Russia also showed an increase in production. In Africa there was nothing of outstanding interest in production, although Egypt showed a decrease and the goverment refinery at Port Said was closed.

Jan 3, 1924

By Courtenay de Kalb

So far as the writer is aware, no detailed investigation into the behavior of ores or rocks when subjected to crushing under digerent conditions has yet been made. He cannot himself claim to have carried such investigations very far; but the results of some studies which he has been pursuing for a couple of years, as opportunity permitted, seem sufficiently interesting and suggestive to warrant a brief statement of them, preliminary to nildertaking a more exhaustive course of experiments. Criticisms and suggestions are earnestly invited, with a view to making these studies as instructive as possible. As a part of the examination of ores, preparatory to concentration, my students have been required to take lots of 100 pounds each, and crush them. These are then screened through a series of hand-sieves, 15 inches in diameter. The products remaining on each screen are weighed, and from the results is plotted a curve, called the sizing-curve. It was assumed at first that different ores would yield, under like conditions of crushing, curves showing unlike characteristics as to the quantities remaining on the various sieves. After a number of such curves had been obtained it became evident, as often happens, that this a priori reasoning was faulty. The curves presented practically identical characteristics, and only by varying the crushing-conditions were variations in the curves obtainable. Another peculiarity, which was as little anticipated, appeared by inspection of these results, namely, that successive crushing to smaller sizes did not greatly augment the quantities of the filler products, so long as the machines employed applied the crushing-force to the ore-particles in the same manner. In these experiments the fines were not eliminated between successive crushings. I believe it will be readily admitted that rock can be crushed

Jan 1, 1899

By Albert J. McIntosh

With petroleum consumption declining temporarily after V-J day, the oil industry is urged to use this period as a kind of stopgap to rebuild its war-depleted inventories and help cushion the effect of this decline on producers and refiners. Higher inventories should be reestablished, since recent experiences have indicated that, by and large, the present inventories of crude oil are too low even with the tremendous current production available. The following analysis indicates that inventory levels could be built up to about 490,000,000 bbl. by the end of 1947, an increase of about 40,000,000 bbl. over the reported stock estimated for the war's end. If at the end of the war the military have some 20,000,000 bbl. on hand, this inventory will either be resold to the industry or certain demands that have been assumed to be met by industry will be supplied out of these military stocks, which would leave about 20,000,000 bbl. (net) to be built up from current production. For stock rebuilding the industry could use 10,000,000 bbl. of crude plus 10,00,000 bbl. of products, totaling 20,000,000 bbl. If this were spread over a year, this would mean 55,000 bbl. a day. By analyzing the average inventories held in a year with the total quantity of goods handled during the year, the following study and tables indicate how far the inventories should increase in the immediate postwar period. Introduction For the period immediately following V-J day, most of the petroleum economists have forecast a considerable decline in the total consumption of petroleum and its products in the United States. This will be caused by the elimination of most of the military demands and the inability of civilians to immediately replace automobiles, burners, etc., and thus increase their requirements to make up for the military decline. When the automobile industry has been back on full production for two or three years, civilians will be able to consume much larger quantities of gasoline. Delay in the manufacture of new oil burners and the time it takes to construct new homes, adds up to the same story for distillate fuels. In reviewing this outlook, the question has arisen whether the petroleum industry should not use this period of lower consumption as a kind of stopgap to rebuild its war-depleted inveritories and help cushion the effect on producers and refiners of this sudden drop in requirements. Some persons have indicated that hundreds of thousands of barrels a day could be used for this purpose extending over a year or more. Refineries will be in existence, which could run over 5,000,000 bbl. of crude oil a day and crude-oil production might be running 600,000 to 700,000 bbl. a day above the demands now forecast for the period after V-J day. Reasons for. Making Inventories In order to plan intelligently for this period, the petroleum industry should determine the needs for the establishment of higher inventories for crude and petroleum products than have been carried during the war. The reasons for trying to make such a determination are as follows:

Jan 1, 1945

By Marcel R. Daly

In a preceding paper1 the writer has pointed out some apparent relationship between the distribution, on the surface of the globe,, of the known hydrocarbon deposits and the disposition of the principal zones of deformation of the earth's body (geosynclines). He wishes to present some further remarks on this subject. Petroleum deposits, or their derivatives or descendants, are found through the whole range of sedimentary strata, from the pre-Cambrian to the Quaternary. For instance, the prc-Beltian (Shuswap) series of the Canadian Cordillera are interbedded with limestones which are sometimes rich in carbonaceous matter (Sicamous limcstone); and the Beltian system of the same region contains layers of argillitcs and dolomitic limestones which are equally high in carbon content.2 This carbon may be interpreted as the last remnant of hydrocarbons previously contained in the rocks. On the other hand, the actual formation of hydrocarbons under conditions that would eventually permit their deposition in modern sediments is conceded by some geologists.3 Between these two extreme limits, bitumens are found indifferently in all sedimentaries. Thcy constitute a continuous series, some kind of a large family, whose individual members may be entitled to a community of origin and probably represent the different stages of evolution of the primitive, parent matter. The kinship between petroleum and such substances as asphalt, ozocerite, manjak, grahamite, albertite, etc., is well known; and E. H. Cunning-gam-Craig has recently shown how intimately shale fields and oil fields are connectcd.4 For this reason, no distinction is made in the present

Jan 1, 1918

By W. B. Agocs

IN August 1954 a low altitude test geophysical survey was made in the Green Pond area of Morris County, New Jersey, with a Gulf Research and Development Co. Model II total magnetic field variation magnetometer mounted in a Sikorsky S-55 helicopter. The test was made in this area to compare the results of a high precision, very low altitude magnetometer survey with an existing ground magnetic survey in this area having known magnetite concentrations, so that the method could be used in areas of difficult access for the detailing of airborne magnetometer anomalies of interest in place of ground surveys. The load capacity of the Sikorsky S-55 permitted installation of a recording scintillation counter so that a radioactivity survey would be made simultaneously with the magnetometer survey. The area surveyed is located at approximately 41°00'N and 74o28'W, just south and east of the town of Green Pond, N. J. The outstanding topographic feature of the region is Copperas Mountain, a well defined ridge, maximum elevation 1222 ft, which runs the entire length of the survey. The lowest point in the survey, 810 ft, is in the extreme eastern corner. Topography of the area is shown in Fig. 1. The three major rock units outcropping in the area are all metamorphic: the Pochuck gneiss, which has been divided into two metamorphic facies; the Byram gneiss; and the Green Pond conglomerate. The relative ages of the Pochuck and Byram formations, both pre-Cambrian, are in doubt, but it is believed that the Pochuck is the older of the two.' The Green Pond conglomerate is Silurian.' Distribution of the outcrops and mine locations is shown in Fig. 1. Two facies of the Pochuck gneiss can be distinguished locally—the Copperas Mountain and Kitchell members. The Copperas Mountain member is a hornblende gneiss, and all the mines and prospects in the area are in this unit. The Kitchell is a quartz-plagioclase feldspar gneiss. The Byram gneiss is a relatively nonresistant valley formation which is high in the potash feldspar. The Green Pond conglomerate is a well indurated quartzite-conglomerate which forms the Copperas Mountain and the Green Pond Mountain's ridge to the north. It overlies the gneisses with a strong angular discordance that may be a fault. The geologic structure of the Green Pond area is relatively uncomplicated. The foliation planes of the gneisses dip steeply to the southeast, and the Green Pond conglomerate dips steeply to the northwest. Additional faulting in the area is indicated at the contact between the Kitchell member of the Pochuck and the Byram along the base of the topographic spur extending to the southeast from Copperas Mountain. The magnetite mines of Pardee, Winter, Davenport, Green Pond, Copperas, and the Bancroft shaft are described by Bayleyl and Stampe2.' The ore is in the Copperas Mountain member of the Pochuck gneiss. The magnetite veins are 10 to 50 ft wide and up to 300 ft long, dipping to the southeast at angles ranging from 40" to 75". The locations of these mines are shown in Fig. 1. Dip Needle Survey: The dip needle survey shown in Fig. 2 was taken from a U. S. Bureau of Mines Report of Investigations." The figure numbers below the local, individual map area outlines refer to the figures in the aforementioned reports which were not contoured. The area of the dip needle survey was confined almost exclusively to the outcrops of the Pochuck gneiss. The separation between survey profiles was 100 ft and the distance between stations on the profiles was 25 ft in highly anomalous zones to 100 ft in magnetically flat areas. A total of 16 1/2 miles of traverse was surveyed over an area of approximately 1/2 sq mile with 2050 stations. The magnitude of the magnetic anomalies is difficult to determine due to the lack of information concerning the type of dip needle used and the procedure followed in making the dip needle survey. This latter would include the method of "zeroing" the dip needle and the procedure of reading at the stations, whether on the swing or statically. Calibrations made of the Gurley dip needle, Lake Superior type, show a static sensitivity of 385 gamma per degree in the range from —25" to +35o, corresponding to a variation in the total field of —9600 gamma to +13500 gamma in a total field of 57000 gamma, inclination 72". The sensitivity increases to 16 gamma per degree from a deflection of 60" to 76", and from 76" to 172" the sensitivity decreases continuously to a low of 260 gamma per degree. From the above it may be seen that it is difficult to assign an arbitrary sensitivity for the dip needle used on this survey. However, an estimated value of 100 gamma per degree may be assigned. On this basis, the majority of the magnetic anomalies, whose deviation is +20°, would be 2000 gamma. Locally, west and northwest of the Pardee mine the magnetic anomaly is +50°, or 5000 gamma; in the Green Pond mine area deviations of +75" are observed that would correspond to anomalies of 7500 gamma. The areal extent and width of the dip needle magnetic anomalies is comparable to profile and station spacing. Hence it is concluded that part of the detail may be due to control, and the probable cause of the magnetic anomalies is at or near surface exposures of magnetite concentrations in the form of veinlets and disseminations whose locations correspond to the local magnetic anomalies. On the basis of the magnetics, none of the magnetite concentra-

Jan 1, 1956

By R. S. Wagner, R. G. Treuting, W. C. Ellis

Use of the Weisseizbevg goniometer for the study of the morphology of whisker crystals and transfer of the results to a stereograplzic projection are described. While in almost all instances a complete and rapid solution is obtained with a purely gaphical treatment, an absolute analytical treatment applicable to difficult cases is given. Examples are given for determination of growth direction and external features of a crystal, for detection of 'twintzittg, and for establislting the orientation relntionships in a kinked whisker crystal. We give here a method for the use of the Weissen-berg goniometerl" in the study of orientation relationships in "whisker" (micro) crystals3-8 and direct transference of the data to the stereographic projection. The operations are straightforward and require no involved calculations: in almost all cases solely graphical treatment is adequate. In a few complex instances, a more exact analytic method may be required. In the method, not only are equatorial reflections of an oscillation photograph used, but also those on higher layer lines, or those not occurring on a recognized layer line. Such reflections off the zero level are often essentialy to detect the presence of twinning. The method is particularly suitable for examination of whisker crystals since the axial or growth direction is almost always one of high symmetry, permitting a more restricted oscillation range to obtain the necessary reflections and an accordingly shorter exposure time. The method is also applicable when there is no lattice-related external symmetry, and is as well able to identify external crystal surfaces, when such exist, with the aid of an optical beam. Thus growth direction, identification of lateral faces, twinning, and orientation relationships in a kinked crystal can be established. A test for the Eshelby twist6-8 can readily be made. The method can be used for orientation, for structure analysis, and as an aid in the identification of an unknown crystal. Moving-film techniques have previously been employed variously for crystal-orientation studies.1,2,9-13 In particular, use of the Weissenberg method for orientation determination has been reported by Wooster and wooster.14 While their method derives the same data as here described, it differs in depending on the tracing of constant p streaks, a less than dependable phenomenon with small specimens, a few microns or less in cross section. The Laue method can and has been used for orientation studies of microcrystals,15 e.g., 2 p in cross section, but requires the extreme intensity and concentration from a microfocus tube to obtain reasonable exposure time. PRINCIPLES OF THE PRESENT METHOD Consider a crystal of random orientation with respect to the oscillation axis in a Weissenberg goniometer. Its diffraction pattern need not necessarily result in recognizable layer lines. In Fig. 1, a stereo-graphic projection of the reference sphere is given with the equatorial plane XZ normal to the oscillation axis Y, and the X-ray beam directed from X towards 2. The great circle ZZ is then normal to the beam, and the axes are right-handed. Thus the reflected X-ray beam lies at the intersection R of small circle ARB of radius 28 from 2, and of small circle RE of radius a from the rotation axis Y. a is the conventional semiapex angle of a cone of diffracted rays from the atoms aligned in the direction

Jan 1, 1967

By L. M. Pidgeon

The reactive metals are above manganese on the electromotive series. Their compounds are characterized by large heats of formation and they cannot be reduced from their ores by classical methods. Three general production methods have been used: a) Fused salt electrolysis, b) reduction of a halide by another metal, and c) reduction of the oxide by another metal. Method (a) is highly developed, as in the case of aluminum, (b) in the case of titanium, and (c) has been successful in the case of volatile metals such as magnesium and calcium. It is suggested that future improvements will take place in (a), and particularly in (c), but are rather less likely in the case of (b). THIS year of 1963 is the centennial of the birth of both Charles Hall and of Heroult, the founders of the aluminum industry. Aluminum is the one reactive metal which has reached massive stature in modern industry and perhaps the only such metal to have been produced in any quantity before the turn of the century. It has been joined by others, some on a very modest scale, but all of importance and all of fascinating interest. When invited to give the Fifth Extractive Metallurgy lecture, it seemed appropriate to look back upon the short history of this group to trace the developments which brought extraction methods to their present state and, at great risk, offer opinions as to future trends.

Jan 1, 1963

By William M. Brewer

History.—The history of gold-mining in Georgia and Alabama antedates the discovery of gold in California. A very large proportion of the gold used in the United States previous to 1849 was produced by these States. A great deal of this history is merely tradition, and no reliable statistics can be obtained ; yet a personal examination of the gold-fields of Georgia and Alabama indicates that tradition is as fairly reliable, with regard to the history of these gold-regions, as it is in any similar cases throughout the world. In Georgia, the history of gold-mining dates back to 1829, when the first gold-mining excitement in the United States occurred. In Alabama, the discovery of gold was made some years later through the work of prospectors, incited by the rich finds in the Georgia mining camps. The greatest product of gold in these States was between the years 1840 and 1849. In Lumpkin county, Ga., and Cleburne county, Ala., the districts from which the most of this gold was taken, the tailing-dumps are silent witnesses of the extensive operations which were carried on by the primitive and crude methods then known. It is no rare thing to see trees 12 to 15 inches in diameter, and even

Jan 1, 1896

By N. S. Greensfelder

The firing of explosive charges by electricity dates back to 1745 when a Doctor Watson is said to have used an electric spark for igniting gunpowder. His method failed in practical application because, to ignite blasting powder, heat must be applied for a period longer than the duration of an electrostatic spark; Wheatstone found that this does not exceed 1/24000 sec. The usual result, therefore, of an electrical discharge in gunpowder is to scatter the grains, without igniting them. Benjamin Franklin partly overcame this difficulty by confining the powder and crushing grains that lay in the line of discharge. In 1822, after the primary cell had been discovered by Volta, Robert Hare, professor of chemistry at the University of Philadelphia, noticed the heating of a short piece of wire placed in the circuit of a voltaic battery. Later work by Oersted, Faraday, Wheatstone, and Henley resulted in the developmcnt of the magneto blasting machines. Fulminates of gold and silver are thought to have been discovcrcd by Cornelius Drebbel, about 1600. Pepys, in his diary for November 11, 1663, recounts a conversation with Doctor Allen, who told him about aurium fulminans "of which a grain ... put in a silver spoon and fired, will give a blow like a musquett and strike a hole through the silvel spoon downward, without the least force upward.'ll This fallacious belief that explosives act downwards only is still held by many who should know better. Fulminate of mercury was discovered by Howard in 1799. J. Shaw of Philadelphia is said to have invented a fulminate-of-mercury cap in 1814; his idea was later adopted by gunmakers in England and France. The principal advantages of mercury fulminate for use in detonators are the simplicity of exploding it and the great shock developed by its explosion.

Jan 1, 1923

By N. S. Greensfelder

The firing of explosive charges by electricity dates back to 1745 when a Doctor Watson is said to have used an electric spark for igniting gunpowder. His method failed in practical application because, to ignite blasting powder, heat must be applied for a period longer than the duration of an electrostatic spark; Wheatstone found that this does not exceed 1/24000 sec. The usual result, therefore, of an electrical discharge in gunpowder is to scatter the grains, without igniting them. Benjamin Franklin partly overcame this difficulty by confining the powder and crushing grains that lay in the line of discharge. In 1822, after the primary cell had been discovered by Volta, Robert Hare, professor of chemistry at the University of Philadelphia, noticed the heating of a short piece of wire placed in the circuit of a voltaic battery. Later work by Oersted, Faraday, Wheatstone, and Henley resulted in the developmcnt of the magneto blasting machines. Fulminates of gold and silver are thought to have been discovcrcd by Cornelius Drebbel, about 1600. Pepys, in his diary for November 11, 1663, recounts a conversation with Doctor Allen, who told him about aurium fulminans "of which a grain ... put in a silver spoon and fired, will give a blow like a musquett and strike a hole through the silvel spoon downward, without the least force upward.'ll This fallacious belief that explosives act downwards only is still held by many who should know better. Fulminate of mercury was discovered by Howard in 1799. J. Shaw of Philadelphia is said to have invented a fulminate-of-mercury cap in 1814; his idea was later adopted by gunmakers in England and France. The principal advantages of mercury fulminate for use in detonators are the simplicity of exploding it and the great shock developed by its explosion.

Jan 1, 1923