Search Documents

By Oswald J. Heinrich

(Read at the Amenia Meeting, October, 1877.) THE deposit of rock salt along the shores of Lake Huron, in Canada, has been brought before the public during the last six months, in consequence of the developments made by the diamond drill at Goderich. It is likely to be of more than common interest in the future, since now actual operations have been commenced to exploit the deposit and work it by regular mining. The methods of mining rock salt being but little known in this country, it may be of interest to make a few general remarks in regard to them before entering, upon the description of this new mining enterprise. According to the conditions under which salt is found in nature, various methods have been resorted to, in course of time, to make it available for the human race. They consist in : A. Natural or solar evaporation. B. Artificial evaporation, either exclusively or in connection with the former. C. Mining the rock salt in its natural state, and converting it to a marketable product, if need be, by simply pulverizing it. Without going into the details of the various methods of making salt available in an economical point of view, dependent on its degree of purity, or on various local influences, we cannot refrain from. alluding to the general principles which influence the mining and manufacturing of salt in countries where they have been carried on for hundreds of years. ECONOMICAL CONDITIONS FOR SUCCESS. Salt being one of the articles of prime necessity, and one universally distributed throughout nature, it must always be sold at a comparatively low price. It would even be quoted in the market at prices far below those now ruling, if it were not for the high duties generally imposed upon it, for purposes of state revenues. But looking closer into the subject, it will be found that this duty is probably one of the least oppressive, although in some countries it exceeds sixfold the cost of profitable production. To produce the article at the lowest possible cost requires, therefore, a

Jan 1, 1878

By E. I. Organick, B. H. Golding

A simple correlation is presented for the prediction of saturation pressures in condensate-gas and volatile-oil mixtures. Saturation pressure is related directly to the composition of the mixture with the aid of two generalized composition characteristics, B, the molal average boiling point, and W, the modified weight average equivalent molecular weight. The need for hydrocarbon equilibrium constants is entirely eliminated. Only the values of the two conlposition parameters need be obtained, and these are calculated in a simple and reproducible manner from the stream analysis of the mixture and the ASTM distillation for the heavy ends. The correlation is given .in the form of a set of 14 working charts in which saturation pressures, either retrograde dew points or bubble points, are plotted cs temperature, forming partial phase envelopes for mixtures having discrete values of the composition parameters, B and Wul. A locus of critical states on each chart intersects the partial phase envelopes, distinguishing retrograde dew point pressures from bubble pressures. A comparison Between experimental and predicted saturation pressures reveals that: the probable error of the predicted values, when considering the data as a whole (214 experimental points), is five per cent; for high gasjoil ratio condensate fluids (approximately 40.000 or more cu ft/bbl) the probable error is about 8 per cent. In either case, however, the probable error is comparable with the overall uncertainty of the data from which the correlation is derived. INTRODUCTION There is a present need for a simplified, yet reasonably accurate method for predicting upper phase boundaries of reservoir fluids. In the case of high gas/oil ratio fluids, namely the so-called highly volatile oils and the condensate gases, no simple method, accurate within 5 to 10 per cent, is now available by which bubble point and retrograde dew point pressures may be predicted. In order to calculate the upper phase boundary of a volatile reservoir fluid, using correlations now available, it is necessary to find and employ the proper K-values (equilibrium volatility ratios of the hydrocarbons in that fluid). This process of finding the Proper K-values usually involves a double trial and error computation. Since the K-values are in themselves dependent upon the composition of the fluid, their use in the calculation of a saturation pressure actually represents an unnecessary complication. The correlation described in this paper relates saturation pressure directly to the stream composition, entirely eliminating the need for K-values. The only data required to calculate the Stream composition are obtained from the customary low temperature fractional analyses of separator gas and liquidt and from the ASTM distillation of the c,+ fraction of the separator liquid. A considerable simplification in the procedure for predicting saturation pressures is thereby effected without significant loss in accuracy. BASIS FOR A CORRELATION Empirical relationships between the saturation pressure and the composition of the fluid in question have already been partially explored by one of the authors.V n particular, a relationship between the critical pressure for a hydrocarbon mixture and its composition was developed. The critical pressure is in reality a saturation pressure, as it repregents a limiting case either of a dew point or of a buhhle point pressure for any given mixture. It was found that the critical pressure may be correlated as a function of two generalized composition characteristics or variables. One characteristic expressed a molal average prop-erty, the other a weight average property of the mixture. Specifically, the molal average boiling point (MABP, or B as it

Jan 1, 1952

By J. Donovan Jacobs

An underground excavation project usually is a highly organized complex of different but interrelated construction activities. It is the whole effort, including the necessary tools, which will be referred to as the System. Tunnel-driving and shaft-sinking operations are among the most systematic of construction efforts. Systems are not new in the performance of construction. It is the Systems Concept which seems only recently to have been discovered and made the subject of much study and discussion. HISTORICAL From the seventeenth century, when explosives were first utilized for rock excavation, until the successful application of the rotary-head continuous tunneler in this decade, the cyclical drill-blast-muck-support method has been standard tunnel-driving procedure throughout the world. Whatever improvements occurred were the result of development of better tools for performing the various operations of the cycle. The electric locomotive replaced the mule and permitted the use of larger muck cars. The steam drill, which ended the day of the double jack, was itself quickly made obsolete when compressed air replaced steam as the source of drilling energy. Power shovels were introduced to save the time and money involved in the hand-loading of excavated materials. A cubic yard of rock tunnel muck can be excavated today for just half the man-hours of labor required in 1948. Developments over 20 years which cumulatively have resulted in this economy include: drifter drills mounted on hydraulically controlled booms and positioners; tungsten-car- bide-tipped bits; long feed shells on the drifters, making it possible to drill the full depth of a round without changing steel; better designed,

Jan 1, 1970

By H. M. Chance

Stretching from New York southwestwardly to Georgia is a great range of hills and mountains consisting of pre-Palæozoic schists, slates, .and gneissic and granitoid rocks, known locally by many different names; in Pennsylvania as the South mountains, the Berkshire or Durham and Reading hills, and in Virginia and farther south as the Blue ridge. To the northwest of this range lies the " Great Valley," underlain by Lower Silurian limestones, and known as the Lehigh valley, Cumberland valley, Shenandoah valley, valley of Eastern Tennessee and Georgia and by other local names, but all these are parts of one valley, geologically and geographically continuous from New Jersey to Georgia. Lying upon and along the northern flank of this range of mountains, and dipping northwestwardly under the limestone of the valley, is the Potsdam formation (Primal or No. 1 of the Pennsylvania Geological Survey), which consists of sandstone or conglomerate overlain by slates. The latter are sometimes arenaceous and occasionally are replaced in part by sandstone. This formation varies from a few feet to several hundred feet in thickness. At the outcrop the slates are completely decomposed, oxidized or disintegrated, forming a belt of clay several hundred feet wide occupying the interval between the outcroppings of the sandstone and limestone. This clay-belt includes a more or less continuous series of iron-ore (brown hematite) deposite, which have been, and still are, extensively worked. The belt is more or less continuously milleralized with iron throughout its length, and hundreds of large deposits of ore have been developed and worked, producing many millions of tons of ore.

Jan 1, 1909

By E. C. Hopkinson, A. H. Youmans, R. A. Bergan, H. I. Oshry

A new log has been developed for quantitative formation evaluation which is based on a measurement of the length of time slow neutrons survive before they are captured in the rocks and fluids. The logging instrument employs a cyclically pulsed neutron generator and a gated scintillation counter which is synchronized with the source. The source emits short, intense bursts of 14 mev neutrons once every 1,000 microsec and is quiescent between bursts. During the period the source is quiescent, the detector is electronically actuated for two independent preselected intervals. A comparison of the counting rates during these two intervals gives a measure of the rate of decay of the slow neutrons and of the associated gamma radiation. The average neutron lifetime in most earth formations is in the range from 50 to 500 microsec. It can be measured during a continuous logging operation at conventional logging speeds. The design of the logging instrument is described and the results of tests are compared with theoretical predictiom. Formulas are developed which give the relationship between log response and formation properties. It is shown that the method is particularly sensitive to formation fluid salinity, and that salt water saturation can be measured accurately in either cased or open hole. The measurement can be made independent of borehole size, fluid type, casing and tool position in the hole by properly selecting the intervals during which the measurements are made. The results of tests with a prototype logging tool are given. INTRODUCTION A new nuclear logging system has been developed which employs the Accelatron,* an accelerator-type neutron source, and accurately measures formation brine saturation in an entirely new way. It has produced a type of formation log with better sensitivity, greater sampling depth and simpler quantitative interpretation than any other nuclear log thus far suggested. The new Neutron Lifetime Log* employs a pulsed electromechanical neutron source and a synchronously gated radiation detector. A prototype instrument has been field tested during recent months to demonstrate the operability of the apparatus and the feasibility of the method. Tests in wells and simulated boreholes have confirmed theoretical predictions and have shown that formation param ters can be measured independent of casing and other borehole parameters. Preliminary results of field tests have indicated that the log may have important and widespread applications. BASIC PRINCIPLE OF NEUTRON LIFETIME LOG The Neutron Lifetime Log is based on the fact that neutrons emitted by a source in a well are rapidly but not instantly captured by the material around the source. Their capture is a matter of statistical probability; the greater the number of capturing nuclei and the greater the "capture cross section", the greater is the probability that a neutron will be captured quickly. The average life of a thermal neutron in vacuum is about 13 minutes, but in common earth materials, the average neutron life ranges between extremes of about 5 rnicrosec for rock salt and perhaps 900 microsec for quartzite. The Neutron Lifetime Log responds to variations in this average neutron life. The theoretical basis for a log of this general type has been well understood by nuclear logging experts in many laboratories both in America and in Russia, and develop mental work along these lines has been in progress for many years. The Russian literature has reported both theoretical and experimental work1,2 but in this country there have been no published reports of progress toward a practical logging instrument. The logging instrument is designed to measure radiation produced by slow neutrons during selected intervals when no neutrons are being emitted by the source. The source is arranged to emit neutrons in bursts or pulses. During the quiescent interval between the pulses, it is possible to observe the exponential "decay" of the neutrons and the neutron-induced radiation as the individual neutrons progressively disappear due to capture by atoms in the formation or the borehole. When a short pulse of 14 mev neutrons is emitted by a source in a borehole, the individual neutrons are slowed to thermal energy within a few microsec. Thus, a cloud of "slow" neutrons is formed around the source within 10 to 50 microsec after the pulse. This cloud is most dense within a few inches of the source, and is progressively less dense out to a radius of about 3 ft, where radiation from the source is practically undetectable.

Jan 1, 1965

By R. F. Janke, J. F. Bossler

Introduction The commercial use of ion exchange resins to recover uranium evolved in the decade following 1950 when significant efforts were made to recover this vital element economically and efficiently from low grade ores. It was discovered that in both acid and alkaline systems, uranium exists as an anionic complex. This led to the application of anion exchange resins to concentrate and purify the uranium product. While this is the simplest statement of what an ion exchange resin does in the recovery of uranium, it should not be forgotten that the industry is continuing to evolve new methods in mining and processing which affect ion exchange operation. The inception of solution mining, the use of expanded bed ion exchange columns and the development of continuous ion exchange systems represent several examples of this continuing evolution in the industry. Throughout all of the changes in equipment designs and variations in solution compositions, the purpose of the ion exchange resin remains the same - to concentrate and purify uranium. Ion Exchange Resins When evaluating ion exchange resins for a uranium recovery project, the task that faces the chemist or process metallurgist is an assessment of the efficiency and, therefore, the economics of the various candidate resins for a given project. This assessment should include consideration of both physical factors such as particle size, density, hydraulic expansion and pressure drop as well as chemical factors such as the uranium loading and elution characteristics. For any given application, the differences in the physical and chemical behavior of ion exchange resins are a function of the conditions used to manufacture those resins. Therefore, an understanding of the way in which manufacturing variables affect resin behavior is important. Since most uranium recovery projects are concerned with recovery of the anionic complexes of uranium using anion exchange resins, this discussion will be restricted solely to the family of anion resins. The majority of the ion exchange resins used in commercial recovery operations look similar to the resins shown in Figure #1. [ ] Most of these materials are based on a styrene- divinylbenzene copolymer. The liquid monomers, styrene and divinylbenzene, are charged to a co-polymer reactor containing water. The water insoluble monomers are then mixed with the water to suspend oil-like droplets of the monomer mixture in. the water. The entire reaction mixture is then heated causing the monomers to polymerize into sol id thermoset plastic spheres. The spherical nature of the particle, the particle size distribution and the primary crosslinking level are fixed in this step in the production process. Figure 2 is a simplified illustration of this step of the process. [ ]

Jan 1, 1979

By K. C. McCutcheson

To a very large extent the quality of a mild steel ingot is determined by the manner in which it is poured into the ingot mold and its behavior during the first few minutes after it has been poured. The formation of the solid rim of metal around the periphery of the mold, the effervescent action of the liquid steel within this solidified rim and the upward or downward movement of the metal level are indications of what is going on beneath the surface of the liquid metal, especially at the interface at which solidification occurs. Observation of this "rimming action" enables an experienced observer to predict the thickness of the sound skin of the ingot and the location and extent of cavities or "blowholes" caused by entrapment of gases. The control of rimming action at the hands of a skillful steel pourer is a vital part of the control of quality in mild steel sheet, and the behavior of the liquid steel during the rimming period is a useful criterion of the melting and refining practices employed in the open hearth. The behavior of rimming steel during solidification depends primarily upon the evolution of gases from the molten metal and it is therefore a problem of considerable interest to determine the nature and amount of the gases evolved. A number of attempts to determine either the amount or the analysis of the, evolved gases have been reported. Klinger,1 in 1925, analyzed the gases extracted from rimming, semikilled and killed steel ingots and found that the chief constituent of the rimming gas was carbon monoxide. The relatively large amounts of nitrogen reported in his first few samples may have been due to incomplete removal of air from the gas-collecting mechanism. McKune2 reported similar studies of rimming ingots from which surprisingly large proportions of nitrogen and hydrogen were evolved. Ameen and Willners3 determined both the amount and composition of gases extracted from unkilled ingots with the aid of diminished pressure. Their ingots weighed only 80 kg. (176 lb.) and apparently were solid within two or three. minutes, so that their

Jan 1, 1938

By W. H. Emmons

A DIATREME is a hole blown through a rock by gases, presumably of volcanic origin. Not all pipes of ore have formed by deposition of metals in such openings, but a con-siderable number have so formed. In this paper are described peculiar vein patterns that are believed to be incipient diatremes or "perforation pipes." Grading into this group is one showing thorough brecciation without rotation of fragments and into the latter a group of ore pipes showing brecciation with rotation of fragments-many of them with well rounded fragments. Also, volcanic craters or volcanic necks are explosion pipes. These may carry ore deposits along their contacts and some carry deposits within the pipes. As new data appear this group becomes increasingly impressive. It has been shown that veins are concentrated in and about cupolas of batholiths and that such veins commonly lienearly parallel to the long axes of cupolas as these are shown on plans. It would be supposed that conical cupolas would have radial patterns, but few vein systems exhibit radial patterns. It is probable that explo-sion pipes also may form in areas above conical cupolas. From these the gases escape more violently because the loads above them are less than above an elongated cupola where larger bodies of rock are affected. The hypothesis is sound mechanically, for the top of an elongated cupola is a line whereas the top of a conical cupola is a point.

Jan 1, 1938

By Frederic P. Dewey

It is common to blame irregular assay results upon volatilization and much has been written upon the subject, but there is no real evidence that, in a properly conducted assay, the loss of either gold or silver by volatilization is sufficient to affect appreciably the result, even when arsenic or antimony may be present. Bulk assays of flue dust from assay muffles have been published, but the data given are totally insufficient to even approximate the volatilization from a single assay; and such figures as we have indicate the volatilization to be extremely small. Diligent search in the literature and wide inquiry among assayers and instructors have failed to produce a single case where the litharge volatilized in making an assay has been collected and assayed for gold and silver. Having attempted to do this, with most indifferent success, I am not surprised that this has not been done. While various textbooks give volatilization as a cause of loss in cupella-tion, it may safely be said that in the rare cases where this volatilization is sufficient to affect appreciably the result it is due to excessive temperature. Percy' says "The loss of silver by volatilization during cupellation is very slight (unless the temperature has been much too high), and may be disregarded." This statement is repeated by the Beringers2 and Smith,3 who includes gold with silver. Mitchell4 says the litharge fume rarely contains over one ten-thousandth of silver. Campredon5 ays that at a proper temperature no silver is lost by volatilization. Primarily, excessive temperature may be due to too high general temperature in the muffle; but it may often be due to temperature localized within the bead by oxidation of the metals and this may be influenced by other causes than the general temperature. I have shown an ex-

Jan 1, 1921

By L. W. Pommier, F. B. Brien, A. K. Bhasin

The diflerential movement of solid particles through solid-liquid suspensions is very important to many branches of engineering. The flow of suspensions around immersed bodies is mainly of a turbulent nature. Problems are encountered when attempts are made, as is the general practice, to extrapolate the velocity and resistance relationships of Newton, pertaining to Newtonian systems, into non-Newtonian solid-liquid suspensions. The conventional velocity and resistance relationships for turbulent flow in fluids when applied to suspensions, do not take into consideration the two very important variables: suspension particle size and solid volume fraction. A study of the effect of suspension particle size (dgb) on the velocity of falling balls leads to the concept of a critical particle size (dgc) at which the suspensions will be Newtonian. This leads to the classification of static suspensions into two types: suspensions consisting of particle of diameter dgh > dgt, and those with dgh, < dgr. Separate velocity and resistance equations for these two types of suspensions have been proposed, taking into account both the solid particle size and solid volume fraction. The agreement between the velocities predicted from the proposed equations and the measured velocities, confirms their validity. The resistance force offered by suspensions to the movement of immersed bodies has been calculated from the proposed equations, and the effects of suspension particle size and solid volume fraction on the resistance force and velocity have been examined. The movement of immersed bodies in solid-liquid suspensions is of great importance in many areas of engineering such as minerals processing, oil well drilling, suspension flow in pipelines, and hydrometallurgy. A number of mineral dressing processes deal essentially with the movement of solids in suspensions—in particular, classification, thickening, filtration, ore washing, and gravity concentration—thus a study of the fluid characteristics of suspensions is of theoretical and practical interest.&apos; A rigorous analysis of the mechanisms of momentum transport of a solid-liquid system is complex indeed. The rheological properties of the suspensions deviate from those of liquids, varying, for example, with density, solid volume fraction, size and shape of the solid phase of the suspension, and with the density and viscosity of the liquid phase. The flow of suspensions around immersed bodies is mainly of a turbulent nature and hence studies of the turbulent flow characteristics of suspensions are of par- ticular importance. Problems are encountered when attempts are made to extrapolate the velocity and resistance relationships of Newton, pertaining to Newtonian systems, into non-Newtonian solid-liquid suspensions. Due to the numerous variables present in a suspension, certain limitations and assumptions become necessary in order to produce quantitative relationships for predicting their effects. The solid particle size and the solid volume fraction are two of the more important variables. By comparing the measured and calculated Newtonian velocities of falling balls in simple static suspensions, the existing velocity and resistance relationships have been modified to take these variables into account. In order to keep the study less complex, all other variables such as the characteristics of suspending liquid and shape of the particle are maintained constant. Objective The objective of the present investigation is to modify the Newtonian velocity and resistance equations in order to take into account the suspension particle size and solid volume fraction. Theory Liquids are classified on the basis of viscosity, which may be defined as the relationship between applied shear stress and resulting rate of shear.&apos; pure single-phase fluids composed of small light molecules behave as Newtonian liquids, having a single viscosity pa-

Jan 1, 1971

By A. J. Lena, M. F. Hawkes

Changes in hardness, tensile properties, microstructure, electrical resistance, and X-ray diffraction effects indicate that lattice strains are necessary for the embrittlement of ferritic stainless steels when heated for relatively short times at 475°C (885°F). It is suggested that 475°C (885°F) embrittlement is due to the accelerated formation of an intermediate stage in the formation of s under the influence of these strains. FERRITIC stainless steels (low carbon alloys of iron with more than 15 pct Cr) are subject to two forms of embrittlement when heated in the temperature range of 375° to 750°C. The embrittlement which occurs after long time heating between 565" and 750°C is well understood; it is caused by the precipitation of the hard, brittle s phase. Sigma is an intermetallic compound of approximate equi-atomic composition with an extended range of formation in Fe-Cr alloys. The maximum temperature at which this form of embrittlement can occur is dependent upon chromium content; and is approximately 620°C for a 17 pct Cr steel and 730°C for a 27 pct Cr steel. The other form of embrittlement occurs after relatively short heating periods in the range of 375" to 565°C; in the higher chromium steels, hours may be sufficient as compared to months for s embrittlement. This phenomenon is not at all well understood and several controversial theories have been proposed. The rate and intensity of embrittlement increase with increasing chromium content but the maximum rate occurs at 475°C re-gardless of chromium content. As a result of this, the phenomenon has been termed 475°C (885°F) embrittlement. The effect of 475°C embrittlement on the properties of ferritic stainless steels has been thoroughly reviewed by Heger.1 The embrittlement causes a pronounced decrease in room temperature impact strength and ductility, a large increase in hardness and tensile strength, and a decrease in electrical resistivity and corrosion resistance. Microstructural changes accompanying embrittlement are minor and difficult to interpret with a general grain darkening, appearance of a lamellar precipitate, grain boundary widening, and precipitation along ferrite veins having been reported at various times. With the exception of reported line broadening, X-ray diffraction studies by conventional Debye analysis of solid samples have been of little value. BY making use of electron diffraction methods, Fisher, Dulis, and Car-roll&apos; have recently shown the existence of a chromi-um-rich, body-centered cubic phase in 27 pct Cr steels which had been aged at 482°C (900°F) for as long as four years. Two types of theories have been advanced to account for the embrittlement. The first of these requires the precipitation of a phase not inherent in the Fe-Cr system with various investigators suggesting a carbide,3 nitride,3 phosphide,4 or oxide." Theories of this type have difficulty accounting for the influence of alloying elements on the embrittlement and for the facts that a minimum chromium content is necessary for embrittlement and the intensity of embrittlement increases with increasing chromium content. The second type of theory that has been proposed relates 475°C embrittlement to s phase formation which is inherent in the Fe-Cr system. An assumption of this kind can adequately explain the influence of alloying elements, for they exert an effect on 475°C embrittlement similar to that on s phase for-mation as can be seen in Table I. The minimum chromium content is essentially the same for both phenomena and it has been shown12,13 that s is a stable phase in the embrittling temperature range. In addition, it has been reported14,15 that pure alloys embrittle to the same extent as commercial type alloys. There are, however, several factors which have prevented complete acceptance of a s phase theory. Foremost of these is that the embrittlement can be removed by reheating for short time periods above 600°C, which in the higher chromium steels is within the stable s region. No s has ever been observed after one of these curing treatments, nor has any s been found as a result of embrittlement at 475°C. In addition, the simple precipitation of s cannot explain the time-temperature relationships for reactions between 350°and 750°C. This behavior is shown schematically in Fig. 1. Newell 16 and Ried-rich and Loib4 have shown that 475°C embrittlement follows a C-type curve as illustrated, while Short-

Jan 1, 1955

By N. B. Pilling

THE development of a proper treatment for shells in connection with war contracts has brought to our attention the fact that the temperature of the liquid bath in which steel is quenched has a decided influence on the speed of cooling in the case of some liquids and very little in the case of others. Widely different physical results have been obtained by the use of water spray, water immersion, and oil immersion and further experiment has shown that the quenching effect of water used as a spray or an immersion varies greatly with the temperature of the water. The present experiments were undertaken with the idea of obtaining information of a quantitative nature regarding the quenching properties of a number of liquids used commercially in hardening steel. The general features of such cooling media are common knowledge and in the literature may be found records of numerous attempts to evaluate the cooling power of a liquid when used as a quenching bath. Much, if not most, of the data given on this subject is in the form of a simple statement of the time required for a certain heated mass to cool between two arbitrary temperatures when immersed in the liquid, quite regardless of the path of the temperature change. Our own purpose has been somewhat different. We have attempted to isolate that property of these. liquids having to do with their ability to absorb heat rapidly, as distinct from the behavior of a considerable mass when exposed to different thermal environments. More specifically, from the data obtained through autographically recorded cooling curves of a small standard mass quenched under various conditions, we have tried to analyze the mechanism of heat absorption by the several liquids, measure the changes in its rate as a function of the temperature of the surface of transference, and ascertain the influence of the temperature of -the liquid itself upon both.

Jan 9, 1919

By R. O. Neal

There are two main sources of the water that floods productive oil or gas sands. The water may rise from the lower depths of the producing stratum, or it may come from beds above or below the oil-bearing formation. Usually the recovery of oil is decreased by water entering the oil sands, and most oil-field waters, especially those of deep wells, tend to foster the formation of an emulsion, which is expensive to treat. This paper deals with a method of distinguishing between waters that encroach upon oil-bearing beds from sources in the same stratum and waters that reach the oil sands from horizons above. In order to remedy effectually water difficulties in oil and gas wells, it is absolutely necessary to determine the source of the invading water. Sometimes evidence such as the structural relations between the strata penetrated by deighboring wells and those found in the well under investigation is not adequate; also, data from drill logs and well records, from mechanical tests made on the wells by plugs, testers, drilling tools, etc., and from tests by chemical indicators such as eosin and Venetian red, may be unsatisfactory, for such data may fail to locate the source of the infiltrating waters. As a resort in such cases, the application of chemical analyses, that is, the comparison of an analysis of the water in question with that of typical waters from the various water horizons in that particular district, has in certain instances proved of value. This method has been used to advantage in the Westside Coalinga field of California, where the source of water may be fairly definitely determined , from its composition. The chief conclusions concerning the chemistry of the oil-field waters in California by G. S. Rogers1 are: "Oil-field water is not necessarily salty, as is generally believed, and may not be even slightly salty to the taste. The degree of concentration of chloride in such water is governed primarily by local conditions and is not affected by the position of the water in relation to oil. Sulfate diminishes in amount as the

Jan 1, 1920

By C. E. Meissner

The need for a practical method of deciding upon new alloy steel analyses to widen its markets was the problem facing the Chrome Steel Works at the beginning of 1927. In addition to determining the physical properties of the alloys under consideration, it was necessary to test their value in service. Small melts of steel in a crucible, from which test specimens could be made, were insufficient to determine more than physical properties, therefore actual castings and ingots had to be made before the products could be placed in service. Furthermore, to save further experimental work, it was desirable that these heats should be made on a "pilot" basis; that is, actually duplicating regular open-hearth furnace practice. Therefore a one-ton (2000-lb.) acid open-hearth furnace was built. Furnace Design There are no special features in the design of this furnace. Standard acid open-hearth practice is followed, with the reproportioning of the dimensions necessitated by its small size; notably, a considerably increased length in proportion to width in order to get proper flame propagation. After the first heat was made it was found that the check-ers were insufficient. The checker chambers were increased in size and the checker openings were made much smaller. The furnace was started late in March, 1927, and made 65 heats. Experimental work was then stopped unti1, the data accumulated could be worked up and summarized. The run was resumed in November and the furnace is still operating, having made at this writing 60 additional heats. For the last series of runs, there was some rebuilding of both the furnace itself and the checkers. Slag pockets were added. Fig. 1 shows details of construction; Fig. 2, the general appearance. All designing was done by the operating and engineering staff. Construction materials were those available around the plant. The reversing valve is a standard butterfly type taken from an old furnace. The slag pockets and checkers are cleaned by digging down to arched openings which have been bricked up.

By J. H. Moran, E. E. Finklea

The pressure build-up technique is a recognized method of determining permeability from conventional drillstem tests. In this paper an effort is made to extend such techniques to the interpretation of data obtained from the wireline formation tester. Such a study is necessary because of the differences, for this case, in the magnitude of the flow parameters (rate of flow, amount of recovered fluids) and in the flow geometry (flow through a perforation vs flow across the face of the wellbore, etc.) involved in the solution of the equations of flow for compressible fluids. The perforation is replaced by a spherical hole, and the effect of the borehole is neglected, so that the flow can be considered to be radial in a spherical co-ordinate system. Arguments are presented to justify this idealization. Assuming single-phase flow, general relations between pressure and flow rate are developed for a homogeneous medium. The study is then extended to permeable beds of finite thickness. It is shown that the early stages of pressure build-up tend towards spherical flow, while the later stages tend towards cylindrical flow. The thinner the bed, the more quickly flow approaches the cylindrical model. The prevalence of thin beds in practical work makes this analysis quite important. Cases involving permeability anisotropy are treated. INTRODUCTION From wireline formation tester operation, two types of data are obtained: (1) the nature and amount of recovered fluids, and (2) the pressure history recorded during the test. A number of papers have been written dealing with the interpretation of formation production on the basis of the recovered fluids.&apos;.&apos; In general, the methods described have been quite accurate for both high- and low-permeability formations. The present paper will deal with an analysis of the pressures observed. An analysis of the pressure build-up curves obtained in hard-rock country has already been attempted on the basis of the formula proposed by Hor-ner. Although this approach has met with success in many instances, some questions have been raised as to its validity. It is the aim of the present study to place the analysis of pressure build-up in the formation tester on a firmer basis, from which more detailed methods of interpretation can evolve. Because of the great differences between the operation of the wireline formation tester and the conventional drillstem test, modifications are necessary in the interpretation. The major difference relates to the flow geometry. Once the flow geometry has been established other features such as multiphase flow, skin effect, afterflow, etc., well described in the literature, can be introduced. It will be assumed that the mechanical operation of the formation tester is already known to the reader.6 t will suffice here merely to state that the tester provides the means for taking a relatively small sample of the fluid immediately adjacent to the borehole, and for recording the subsequent pressure response. In comparison with conventional drillstem tests, the time required for a satisfactory pressure build-up response is much shorter, because of the relatively small quantity of fluid withdrawn by the wireline tester. This feature is highly desirable in the case of low-permeability formations. For an analysis of the pressure response within the formation, three simple flow geometries are considered— linear, cylindrical and spherical. The spherical and cylindrical flow geometries are most pertinent to the formation tester; therefore, they will receive the major emphasis. Since the configuration of the borehole and the perforation made by the tester complicate the flow geometry, it is necessary to allow for them in the drawdown response. However, because of the volume of formations contributing to the pressure-response, the details of the perforation shape are unimportant in the build-up period. Since relatively small amounts of fluid are withdrawn from the formation, in contrast to a conventional drill-stem test, a study of the "depth of investigation" and the significance of drawdown as well as build-up data will be included. Because the "depth of investigation" will be shown to be rather large, the effect on the build-up curves of the finite thickness of the permeable bed is considered. It is this consideration that leads to the importance of cylindrical flow geometry. Also included is a discussion of permeability anisotropy and its effect on the interpretation of the tester results. The pressure curves recorded by the formation tester will follow two general patterns, depending upon whether the formation is of high or low permeability. Fig. I (a and b) schematically illustrates these two responses. In Fig. 1(a), the high pressure recorded during fill-up of the tool is essentially the pressure differential across the choke in the system. In Fig. l(b), the flow rate is

By Edward Schuster

As THE time allotted is short, we can present only a general idea of the oil laws in the Latin-American republics, as a supplement to Bulletin 206 of the Department of the Interior compiled under the direction of J. W, Thompson of the Bureau of Mines and entitled "Petroleum Laws of All America." We shall not discuss the European colonies in Latin-America nor the island republics. As to the countries discussed, we shall attempt to give the main features of such special petroleum legislation as has been adopted prior to the early part of this year; where no special petroleum" laws exist, we must look to the mining codes for light on the petroleum policy. As the laws and regulations for the extraction of the metals are often difficult of application to, and are lacking in many essentials for, the petroleum industry, it is best for persons or companies desiring to enter, on . a large scale, into the petroleum exploration and development of countries not having special petroleum legislation, to obtain a concession contract from the executive of the country under consideration, and to have the concession approved by the congress. If this concession, which would then be a special law, contains nothing contrary to the constitution of that country and does not infringe on vested rights of third parties, it should be reasonably safe. If in such country there is some doubt as to whether the petroleum subsoil is owned by the nation or the private surface owner, only public lands should be covered with the concession. Guatemala is the only republic in the group that discriminates directly against foreigners. Bolivia, Ecuador, Mexico and Venezuela require waivers of diplomatic protection.1 Colombia requires foreigners to agree to be bound by its alien law. , In addition,Mexico makes it unlawful for foreigners to acquire direct ownership of real estate, including mines, within a zone of 50 km. along the coasts and one of 100 km. along its land

Jan 7, 1922

By G. Rowan, M. W. Clegg

Approximate analytical solutions for non-Darcy radial gas flow are derived for bounded and infinite reservoirs producing at either constant rate or constant pressure. These analytical solutions are compared with published results for non-Darcy flow obtained on digital and analogue computers, and the agreement is show to be very good. Some observations on the interpretation of gas well tests are made. INTRODUCTION The flow of gases in porous media is a problem that has been the subject of much study in recent years [l - 71 , and many methods have been proposed for solving the non-linear equations associated with it. The assumption that the flow satisfies Darcy&apos;s Law It has been observed, however, that the linear relationship between the flow rate and pressure gradient is only approximately valid even at low flow rates, and that as the flow rate increases the deviations from linearity also increase. It has been suggested by a number of authors that Darcy&apos;s Law should be replaced by a quadratic flow law of the form This form of equation was first suggested by Forchheimer [9] and, later, Katz and Cornell [10], and Irmay [lll, developed a similar equation. Houpeurt [12] derived this form of equation using the concept of an idealised pore system in which each channel consists of sequences of truncated cones giving rise to successive restrictive orifices along the channel. This type of representation leads to a quadratic flow law of type [4], for all fluids, but it is found that the quadratic term is only significant in the case of gas flow. The methods of Houpeurt for solving gas flow problems will be discussed further in another section of this paper. Solutions of the non-linear equation for Darcy gas flow 121 may be classified as either computer (digital and analogue), or approximate analytical ones. The former include the well-known solutions of Bruce et al. [13], and Aronofsky and Jenkins [14] , but the latter solutions, apart from the simple linearisation of equation (2) to yield a diffusion equation in p2 , are not so well-known. Amongst these approximate analytical solutions should be mentioned the work of Barenblatt [IS], who has applied the techniques of dimensional analysis to obtain similarity solution to a large class of non-linear equations; also, a number of Russian authors, including Barenblatt [16] , Kim [17] and others, who have used the method of moments for obtain-

Jan 1, 1965

By Ligon Johnson

ONLY the acute phase of the smelter fume problem is new. The problem itself is older than the Christian era. While both lead and copper were mined and crudely smelted ; on: 3,000 years ago, it was not until the Roman occupation of the Iberian Peninsula and the British Isles, which occurred but shortly before the beginning of the Christian era, that there was any evidence of smelting operations on a scale sufficiently large to permit a fume problem. Around Huelva, Spain, are found more than 30 million tons of slag from lead smelting conducted there by the Romans. Pliny tells us that more than 20,000 slaves were employed in the Iberian mines. Extensive mining and smelting by the Romans in England and Wales were coincident with the Iberian proceedings. These metallurgical operations were upon a sufficiently large scale to produce marked results both upon the surrounding country and the smelter workers, but, as they were those of a conqueror upon conquered soil, conducted by slaves, imperial Rome failed to recognize that such a thing as a smoke problem did or could arise, and whatever fume question there may have been at that .time remained a question only to those who had no chance to answer any phase of it. The smelting operations of the Romans extended over about 400 years, and little is "recorded of lead and copper smelting from that time until the 16th century. From the revival beginning at this period up to the present century, the growth of smelting has been comparatively gradual. In Great Britain, smelting was conducted almost wholly in localities where metallurgical operations were of paramount importance, and the communities that grew up in smelter localities were due to and dependent upon the mines and smelters. This fact had much to do with the comparative freedom of British smelting from burdensome fume litigation and legislation. To a lesser degree these conditions applied to the German operations which, when coupled with the further fact that most of the early German operations were to a greater or less degree fiscal workings of Prussia, Saxony and Brunswick-Hanover; accounts for

Jan 5, 1917

By Samuel Thomas

The specimen of anthracite coal which I hold in my hand, insignificant as it may appear to the casual observer, speaks volumes to me and to the initiated, as it suggests and represents the entire evolution of the use of anthracite coal in the manufacture of pig-iron, the growth and development of which it is my purpose to review here to-day. During our recent visit to the Mountain Copper Co.&apos;s works at Keswiek, I picked up this piece of coal from a pile of anthracite lying in the yard, asked Mr. Edwards, the manager, a countryman of mine, where it came from, and, to my surprise and delight, discovered that it had been brought all the way from Wales, and had come out of the identical vein which my father opened near Yniscedwin, about eighty years ago. I had no idea, before this incident, of contributing to the already full and complete programme of the day; but, being requested by our distinguished President and Secretary to do so, I consented to relate here the story which this remarkable find naturally brought back to my mind.

Jan 1, 1900

By J. B. Hess, R. L. Dietrich

IN the mechanical twinning of magnesium on the {1012} planes the crystallographic deformation is such that, in the direction of the hexagonal axis [0001], twinning is possible only under tension stress, while in the directions perpendicular to the hexagonal axis, twinning is possible only under applied compression. Thus in extruded magnesium and magnesium alloys where the extruded textures are best described as either [1010] or [ 1120] fibers,1 the basal planes are all nearly parallel to the extrusion axis and such material is susceptible to {1012 } twinning by compression in the direction of the extrusion axis. In order to explain the results of cyclic stressing in alternate tension and compression upon the tangent elastic modulus in such material, Dorn and Thomsen2 have postulated that, following twinning under applied compression, a retwinning or untwinning occurs as a result of residual microtensile stresses immediately upon removal of the applied compressive force. Recently, Carapella and Shaw3,4 have used this supposition of untwinning in magnesium in discussing their results on indentation hardness and on cold drawing of MI sheet. In trying to confirm this hypothesis by suitable direct experiments, the authors have been unsuccessful in detecting any evidence whatsoever that untwinning follows the release of applied compression and are forced to conclude that this hypothesis is improbable or, at least, that the quantity of material involved is small. For the experiments, small cylindrical specimens 0.040-in. diam. X 0.120- to 0.140-in. long were etched from 0.0625-in. extruded rod. The ends of the specimens were accurately faced off parallel in a jeweler&apos;s lathe. The compression jig was simply an ordinary set of micrometer calipers with an anvil interposed between the spindle and the specimen. The anvil was free to move axially but restrained from rotating so that the rotation of the spindle would not introduce a twisting stress on the specimen. With this arrangement the compressive strains could be estimated to 0.0001 in. and X ray pinhole photographs could be taken with or without load as required. Fig 1 is the pattern of an uncompressed specimen of AZ31 alloy, showing the approximate [1010] extrusion fiber. The X ray beam is normal to the extrusion axis; in this position it is particularly sensitive in detecting twinning if one directs his attention to the diffraction ring from the basal plane. Since twinning on {1012} planes produced an 86° reorientation of the crystal lattice, the original basal reflections occur at the 3 and 9 o&apos;clock positions while the (0002) reflections from any twinned material will occur at the 6 and 12 o&apos;clock positions. Fig 2 shows the same specimen compressed 3.0 pct, photographed while still under load. This strain has been just enough to produce a detectible amount of twinning and the sensitivity is roughly indicated by the fact that no alterations were produced in the intensities or maxima of the other diffraction rings. A strain of

Jan 1, 1948