Search Documents

By J. T. Burwell, J. Wulff

As is well known, the alloys of iron containing 18 ± per cent chromium, 8* per cent nickel and less than 1.2 per cent carbon exhibit the same allotropic modifications as iron. The face-centered cubic or gamma phase is stable at high temperatures and the body-centered cubic or alpha ferrite is presumably stable at room temperature. The transformation from the gamma phase to the alpha phase in alloys of the above composition (18-8 or stainless steel) is sluggish; even moderately rapid cooling permits the retention of the gamma phase. Cold-work, however, causes the transformation from gamma to alpha to occur at room temperatures. It is difficult, nevertheless, to induce complete transformation regardless of the method of cold-working. Since metallographic polishing is very effective in transforming the surface austenite to ferrite, as indicated by the magnetic studies of Buehl and Wulff,1 it was decided to investigate the phenomenon by electron diffraction methods. Apparatus The apparatus used (Fig. 1) was a hot-filament type employing movable slits, similar to that described by Germer.2 The sample-to-photographic plate distance was 69 cm. and the accelerating voltage 30 kv. Since electrons do not in general follow geometrical paths, it is necessary that either the electron source or the sample be movable in a plane normal to the beam. In this case the sample is fixed and the electron source is movable. The source is adjusted until the shadow of the sample appears in the brightest part of the beam as viewed on the fluorescent screen, then the slits composing the two pinholes are inoved into position one by one. The system is evacuated by means of a mercury diffusion pump backed up with a Cenco Hypervac oil pump. Pressures lower than 10- mm. of Hg are read on a calibrated ionization gauge.

Jan 1, 1939

By Pope Yeatman

THE Committee on the Elimination of Waste in Industry, of the Federated American Engineering Societies, in its report says that "Waste in -industry is attributable to four causes: 1. Low production, caused by faulty management, of materials, plant, equipment, and men; 2. Interrupted production caused by idle materials, idle plants, and idle equipment; 3. Restricted production intentionally caused by ,owners, managers, or labor; 4. Lost production caused by ill-health, physical defects and industrial accidents. The committee sent out elaborate questionnaires, and in them divided the responsibility into Manage-ment, Labor, and Outside Contracts. These question-naires showed that in the different industries examined the responsibility of Management was from 50 to 80 per cent. and of Labor from 9 to 28 per cent. The percentage of responsibility that Management was held accountable for was much larger than any of us supposed. However, when this question is studied, we realize how necessary it is to select, in the first instance, suitable personnel, in the form of directors, managers, heads of departments, experts, etc. We would like to -believe that the percentage of responsibility of Management for waste in the mining business was less than that quoted above, but there are so many mining properties started up and operated by men of no experience in such lines, and there have been so many improvements in late years in mining and metallurgical methods not taken advantage of, that we can not believe that. the percentage will vary much from that already quoted. Quoting from a report approved by the Committee on Management of the American Society of Mechanical Engineers: Management is the art and science of preparing, organizing, and directing human effort applied to control the forces and util-ize the materials of nature for the benefit of man.

Jan 3, 1922

By H. W. Morse

MANY of our largest copper deposits contain both sulfide and oxidized copper minerals. The large porphyry mines, with a total copper content of from 1.3 to 2.0 per cent., send to their mills ore with an oxide content of from 0.2 to 0.4 per cent. While the recoveries of the sulfide minerals are considered satisfactory, using modern flotation practice, the recovery of the oxi- dized portion of the copper is small; better recoveries of oxidized copper were made before flotation methods were adopted. Beside the ores containing copper mainly as sulfide, with a small amount of oxidized copper,, many of the large porphyry mines have oxide orebodies, in which the propor-tion of non-sulfide minerals is so high that 2 present methods of treatment are ineffi-cient. In some of the well-known ore-bodies in the Miami-Inspiration district the copper occurs about equally in sulfide and oxidized forms; and the mixing of minerals is complete throughout the ore-body. There is no possibility of mining the sulfides and the oxides selectively. At the New Cornelia mine, however, the oxide, and sulfide ores are sharply separated, per-haps by an ancient water level, so that the oxide ore may be mined and treated in a plant built for that purpose, and the under-lying sulfide ore may be left for treatment in another plant. If copper is to be made from an ore having a total content of 1.5 per cent., it must be concentrated or removed from the ore by some. hydrometallurgical method. Flotation is generally successful for the sulfide minerals and flotation after filming with sulfide seems to work in many cases on the pure carbonate minerals. Callow has given an extensive report on the results of "sulfidizing" flotation on the ores of the. Magma mine.1 Where such ?a 'method can be applied, it ?may be, the best

Jan 9, 1922

By J. T. Burwell, J. Wulff

As is well known, the alloys of iron containing 18 ± per cent chromium, 8* per cent nickel and less than 1.2 per cent carbon exhibit the same allotropic modifications as iron. The face-centered cubic or gamma phase is stable at high temperatures and the body-centered cubic or alpha ferrite is presumably stable at room temperature. The transformation from the gamma phase to the alpha phase in alloys of the above composition (18-8 or stainless steel) is sluggish; even moderately rapid cooling permits the retention of the gamma phase. Cold-work, however, causes the transformation from gamma to alpha to occur at room temperatures. It is difficult, nevertheless, to induce complete transformation regardless of the method of cold-working. Since metallographic polishing is very effective in transforming the surface austenite to ferrite, as indicated by the magnetic studies of Buehl and Wulff,1 it was decided to investigate the phenomenon by electron diffraction methods. Apparatus The apparatus used (Fig. 1) was a hot-filament type employing movable slits, similar to that described by Germer.2 The sample-to-photographic plate distance was 69 cm. and the accelerating voltage 30 kv. Since electrons do not in general follow geometrical paths, it is necessary that either the electron source or the sample be movable in a plane normal to the beam. In this case the sample is fixed and the electron source is movable. The source is adjusted until the shadow of the sample appears in the brightest part of the beam as viewed on the fluorescent screen, then the slits composing the two pinholes are inoved into position one by one. The system is evacuated by means of a mercury diffusion pump backed up with a Cenco Hypervac oil pump. Pressures lower than 10- mm. of Hg are read on a calibrated ionization gauge.

Jan 1, 1939

By Harry K. Ihrig

THE hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1/8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was, necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes Co. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.11 The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 DESCRIPTION OF TEST METHOD The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1945

By Franklyn W. Oatman

In order that the conditions which obtain in an oil well may be readily understood, a brief description of a typical California well and a number of the phenomena accompanying same will be given. That the necessity for the exclusion of water be realized, the effects of water intrusion, a description of methods of prevention, .and a discussion of causes of failure will be presented, followed by a summary and recommendations. Fig. 1 shows a section of a typical well which illustrates the relation of oil sands to overlying strata. It indicates a deep water sand separated from the oil sand by shale, and the proper place for the final shutting off of water. In this well a comparatively thick stratum of compact shale protected the oil from overlying water so that the operation of landing the water string was a simple matter. In some wells the protecting stratum may be only from 3 to 5 ft. thick and very careful operation is necessary in order to land the water string of casing properly and not puncture through to the oil sand. The cases just cited are common, but occasionally, after excluding overlying water, productive oil sands are drilled through in the expectation of finding more productive underlying sand, and a water-bearing stratum is tapped. In this case the problem is the reverse of the normal; water must be prevented from ascending rather than descending. A discussion of well-drilling methods is not within the scope of this paper, except such operations as pertain to shutting off of water. A brief outline of the several conditions which may accompany drilling follows. Some or all may be present in any particular case. The direct relation of these to prevention of intrusion will be discussed in detail further on. In drilling, the hole becomes more or less irregular in shape, and rough, and as the casing follows the bit into the well it does not fit snugly against the walls. As a result, water may descend between the casing and walls of the well. If a circulation pump is not used during drilling, the hole is simply punched through and the pulverized material removed from the well by means of a bailer. If circulation is maintained there is a continual flow of water down inside the casing and up around the outside between the pipe and the walls of hole. This keeps an open space around the pipe.

Jan 1, 1915

By George A. Johnson, Leon H. Banks

The Missouri-Kansas Zinc Corpn., operating in the Waco district, 15 miles northwest of .Joplin, Mo., owns large tailing piles made during milling operations of the years 1918-28 by the Butte-Kansas, Acme, and Barnsdall mining companies, whose holdings have been purchased and consolidated under the ownership of the Missouri-Kansas Zinc Corpn. These tailings had been considered too low in value to be worth retreating by the ordinary methods. C. Erb Wuensch, consulting engineer of the Missouri-Kansas Zinc Corpn., noted the difference in the type of tailing from upper-level and lower-level ore. The latter contained hard lime chats. He also found that mill losses had been due to particles of blende on the corners or sides of the chats and to the existence of soft, porous, cellular, lime chats containing varying amounts of blende. He conceived the idea that a quick grind in rolls or hall rnills might change the type of the rnaterial so that jigging could rnake a clean tailing for discard and a partly concentrated product sufficient in blende content to justify the expense of fine grinding in hall mills to free the mineral entirely. A laboratory was equipped with the necessary machines and the writers were assigned the problem of developing a method of retreating the tailings. Laboratory Testing From preliminary drill sampling of each pile was obtained the blende content, the soluble sulfate content, and the general characteristics of the material to he treated. The tailings were a mixture of lime and flint with some shale. Visual examination showed most of the blende to be in the dolomite and very little in the flint, although there were some flint particles with blende on the cleavages. The blende was found as particles on the corners or cleavage faces in one type of chat and in another disseminated in a soft, porous, cellular lime. Because of the porosity of the latter type of chat, the apparent specific gravity, under hindered-settling conditions, is less than that of a solid piece of lime or flint. That it,

Jan 1, 1930

By A. M. Talbot

THERE is still considerable controversy as to the exact nature of the mechanism of the age-hardening process, in spite of the many experi-ments already performed. For this reason, a considerable number of typical systems should be examined in detail and their results correlated. Furthermore, the methods of studying the changes that take place during the progress of this phenomenon should be carefully scrutinized and the different methods applied to the same samples, preferably at the same time. The experiments described in this paper are presented to supply information on one age-hardening system and to show how the various methods of investigation compare in their indication of what has hap-pened. In brief, the progress of aging in magnesium alloys containing about 10 per cent by weight of aluminum at different temperatures was followed by measurements of hardness, electrical resistivity, dilation and lattice parameter, and by microscopic observation.

Jan 1, 1936

By George H. Willis

In the second half of the 19th century, bimetallism progressively was replaced by gold standard. After World War I and the 1931-33 depression, gold was mainly reserved for official international transactions and internal use was restricted. Changes since 1971 have shrunk official international use of gold. International payments deficits and surpluses are now financed by Private and official credit, rarely by gold. This historical review covers evolution of: (1) internal and external private use, (2) internal official use, (3) external official use, (4) its role in the International Monetary Fund, and (5) use as unit of account. For this paper I have tried to take a longer perspective than is usually possible, and to look, even if very briefly, at the changing relationship of gold to the monetary system over the last 200 years or so. There are, I believe, some long-term trends, continuing down to the present day. These trends have seen gold replaced by some form of paper assets in one monetary function after another. These past trends may help us to understand where gold stands now, and possibly will throw some light on the future. Because it seems to me that gold in the past has performed various functions related closely or marginally to money, I have divided this rapid historical review into several sections: (1) the internal and external private use of gold, (2) the internal official use of gold, (3) the external official use of gold, (4) gold and the International Monetary Fund, and (5)gold as a unit of account.

Jan 1, 1980

By B. Barlin

Introduction The development of metallurgical practice at lambia Broken Hill is directly related to the change in mineralization of the deposits as mining progressed from the open pits to underground. The ore consists of a mixture of lead and zinc sulphide minerals, together with abundant silicates, carbonates and other oxidized minerals of these metals. The irregularity that characterizes the shape of the orebodies applies equally to their mineral content, which makes ore reserve calculations and the maintenance of a balanced feed to the metallurgical plants, problems of some magnitude. History The Rhodesia Broken Hill Development ,Company was formed in 1904 after an Australian prospector, T. G. Davey, discovered the outcrops in 1902. In the early years zinc ores were calcined for shipment but this proved uneconomic. Cerussite outcrops were then smelted directly in blast furnaces for the production of lead until 1929 when ore above the water level was exhausted.

Jan 1, 1970

By Frank Wartman

RECENTLY Horace Freeman1 obtained a patent on a successful method of conducting a roasting procedure described as to general features by Carl Schnabel2 almost forty years ago. Essentially, the Freeman process of roasting consists in introducing the finely powdered sulfide mineral, suspended in air or any other suitable gaseous medium, into the upper portion of a heated chamber. The stream of suspended particles is directed vertically downward. A counter-current stream of gas introduced at the bottom of the chamber flows upward. The mineral particles are oxidized as they fall through the heated atmosphere of the chamber. All air required for the oxidation may be admitted either at the top or the bottom of the chamber, or may be divided between the top and bottom inlets in any desired proportion. Heat may be recovered by passing the gases leaving the furnace through a waste-heat boiler or other form of interchanger. In speaking of the results obtained in roasting pyrite, Freeman says:3 Steam yield from the boiler exceeds 1 pound of steam per pound of pyrite con-sumed, which pays the cost of operation of the burner. The oxide produced is in the form of fused particles or hollow shells of magnetite, containing about 65 per cent of iron. It contains the gangue material ordinarily produced in flotation concentrate, of course, but it is being found that most of this can be eliminated by magnetic separa-tion, and that the sulfur content, as consistently produced, is below 0.2 percent. This material is especially interesting as a high-grade iron ore, free from phosphorus and low in sulfur. It may be sintered or briquetted. It is even more interesting as a raw material for sponge-iron production, to be directly smelted in electric furnaces without the usual cooling of the iron powder and magnetic separation between the reducing kiln and the electric furnace.

Jan 1, 1933

By D. L. Wood, J. H. Westbrook

The tensile behaviors of the CsCl structure compound AgMg are extensively documented in terms of strain, strain rate, temperature, composition, and metallurgical processing treatment. The observations lend themselves to presentation in terns of three regimes of deformation behavior; 1) low temperatures where deformation is primarily by slip; 2) intermediate temperatures where the deformation mode is also slip but with the detailed behavior dominated by dislocation interactions with solute atoms; 3) high temperatures where defomation is primarily by diffusion controlled processes. Of all the material groups of potential interest as high-temperature structural materials, the inter-metallics have been the least studied, particularly with respect to their mechanical behavior. Moreover, the application and processing of intermetallics for uses which exploit their often unique physical properties have been impeded by a lack of understanding of their mechanical properties. Previous work in this area* has been largely *For a recent review, see Westbrook.' exploratory, aimed on the one hand at the direct empirical development of materials of engineering utility and ,on the other at identification of the important parameters affecting the mechanical behavior of inter metallics. As a consequence, there has not been available, heretofore—for any inter-metallic—data, sufficient in extent or precision to provide an adequate phenomenological description of the effects of metallurgical variables on deformation behavior. Such documentation is prerequisite to intelligent application or processing design and is also necessary for testing present and future theoretical analyses of mechanical behavior. It was therefore an objective of the present investigation to document the deformation behavior of a simple ordered intermetallic over as wide a range as possible of all the usual metallurgical variables. The compound AgMg was chosen as the subject of this investigation because it met all of a group of desired criteria, namely: 1) congruent but moderate melting point; 2) simple crystal structure; 3) ordered structure persisting to the melting point; 4) broad solubilities for the component elements. The first and last criteria were expected to aid in the preparation of homogeneous single-phase specimens: the second and third to help simplify the

Jan 1, 1962

By J. C. Sullivan, W. A. Knoll

The sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In Novernber of 1930, experimental work was conducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4½-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. Drilling Air was carried down the shaft in an 8-in. flanged pipe line at a pressure ranging from 95 to 100 Ib. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1940

By Charles F. Ramseyer

The manufacture of iron and steel is one of the largest of our industries; and in point of size of single plant and equipment certainly the biggest of all industries. By the general public it is generally considered a prime example both of the marvelous technical advances achieved by modern science and engineering in the design and operation of equipment and of the efficiency of big business in the coordination of men and materials. Actually the operation of its basic processes has not changed significantly in either theory or fundamental design of equipment in the past 75 years. Though many other process industries have been born and developed, and not seldom completely revolutionized, during this period, the primary processes of making iron and steel are still carried out along the lines laid down, and in the equipment originated so long ago, by Bessemer, Siemens and Martin, and subsequently expanded to practically the modern scale by Carnegie, Schwab and Captain Bill Jones in the eighteen eighties and nineties. The application of the principles underlying the continuous counter-current physical and chemical interaction of solids, liquids and gases, which have been so successfully used in the rapid evolution of our chemical process industries, has been very largely lacking in the steel industry. In the days of the last-named giants, especially Carnegie, the steel industry made great and rapid technical progress. Carnegie's ever driving idea (as later with Ford in the production of automobiles) was the finding of new and better ways of making cheaper steel. Carnegie himself was a steelman, and so long as he dominated the industry its technical progress was rapid; and he, like Ford, was vastly successful financially as well, since his costs were continually being driven lower than those of his competitors by his advances in steelmaking technique.

Jan 1, 1935

By J. C. Sullivan, W. A. Knoll

The sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In Novernber of 1930, experimental work was conducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4½-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. Drilling Air was carried down the shaft in an 8-in. flanged pipe line at a pressure ranging from 95 to 100 Ib. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1940

By R. E. Hook, R. L. McGaughey, A. M. Adair

The initial yielding characteristics of a vacuum-melted iron have been measured as a function of thertnal history after slow cooling or quenching from a 700°C recrystallizntion anneal. A thermal history favoring the segregation of interstitials to grairz boundaries results in a material having high values of upper and lower yield stress and long, irregutar Luders' plateaus, wheueas specimens treated to minimize grain boundary segregation have significantly lower values of these yielding characteristics. The struc- ture of typical grain boundary areas as revealed by electron transmission microscopy is consistent with these findings. The grain boundaries in iron are considered to be principally responsible for the release of dislocations during macroscopic yielding and it is suggested that strong locking results when a substantial amount of grain boundary segregution is present; it follows that weak locking results from a more random distribution of interstitials to grown in dislocations. RECENT years have seen an increased emphasis placed on a more quantitative study of the influence of grain boundaries on the yield behavior of bcc metals. The earlier picturk of dislocation pileups at grain boundaries building up a sufficient stress concentration to unlock dislocations in neighboring grains1

Jan 1, 1967

By Charles F. Ramseyer

The manufacture of iron and steel is one of the largest of our industries; and in point of size of single plant and equipment certainly the biggest of all industries. By the general public it is generally considered a prime example both of the marvelous technical advances achieved by modern science and engineering in the design and operation of equipment and of the efficiency of big business in the coordination of men and materials. Actually the operation of its basic processes has not changed significantly in either theory or fundamental design of equipment in the past 75 years. Though many other process industries have been born and developed, and not seldom completely revolutionized, during this period, the primary processes of making iron and steel are still carried out along the lines laid down, and in the equipment originated so long ago, by Bessemer, Siemens and Martin, and subsequently expanded to practically the modern scale by Carnegie, Schwab and Captain Bill Jones in the eighteen eighties and nineties. The application of the principles underlying the continuous counter-current physical and chemical interaction of solids, liquids and gases, which have been so successfully used in the rapid evolution of our chemical process industries, has been very largely lacking in the steel industry. In the days of the last-named giants, especially Carnegie, the steel industry made great and rapid technical progress. Carnegie's ever driving idea (as later with Ford in the production of automobiles) was the finding of new and better ways of making cheaper steel. Carnegie himself was a steelman, and so long as he dominated the industry its technical progress was rapid; and he, like Ford, was vastly successful financially as well, since his costs were continually being driven lower than those of his competitors by his advances in steelmaking technique.

Jan 1, 1935

By Edmund Kirby

THE results to come from the application of cheap oxygen to industry in general will be so great that it is not possible to enumerate them beforehand and still less to estimate them. We naturally think first of the fuel to be saved; yet this is only a minor item. The main results will be changes in methods of manufacture or of operation. The speed of operation will be greatly increased, with consequent savings in labor and fixed charges, and also, in most cases, in the cost of fuel. High temperature will be brought within the reach of every manufacturer, whereas it is now available only to those operating expensive electric furnaces located within reach of large water power. New speeds and new temperatures mean improvements and processes not thought of at present. Incidentally the changes in methods will probably change the location of important world industries, the tendency being to concentrate at the fuel centers. The whole subject is so new that most of the data which an engineer requires for definite estimates do not exist. All that is possible now is to obtain a general view of the subject with rough and fragmentary estimates for some of the industries with which we are specially concerned. Most of the figures presented deal with fuel saving merely because there are available no data from which to estimate the effect on speed of operation. When working out the practical problems involved in substituting oxygen for air, in most cases the change will be made step by step; by trying out air enriched with increasing percentages of oxygen. Such partial applications of oxygen will be temporary expedients during the transition and there will be no stopping place short of the complete substitution of air by oxygen. This final stage is therefore the one discussed in this paper.1

Jan 11, 1924

By W. F. Vietti

Operations in the Texas Gulf Coast during the past year have resulted in the discovery of a number of new fields arid the extension of a few of the older fields, both by deeper drilling and by lateral development. Twenty-six new oil and gas-producing areas and discovery of oil or gas in three subsequently abandoned wells have been recorded for a total of 29 new fields of varying importance. Producing areas at Conroe, Manvel, Greta, Pierce Junction, Hastings, Dirks, Thompson, Batson, Mykawa, Tomball, Raccoon Bend, Samfordyce arid Saxct have been increased. Primary geologic studies followed by geophysical mapping or straight geophysical prospects have been responsible for the more important discoveries. These methods have further proved themselves an aid to limiting wildcatting to the more prospective areas and as the chief means to discover reserves in the future. Production for 1935 totaled 69,560,720 bbl. as compared with 60,850,-360 bbl. for 1934. Strict proration has been in force throughout the discovery of more oil than has been produced. The number of producing oil wells has steadily increased to 4851 at the end of 1935, as compared with 3858 at the end of 1934, owing in part to the prolonged life, because of proration. There were 1272 oil and gas wells completed during 1935, as against 835 in 1934. New Fields Pertinent data on the new fields discovered during 1935 are includrd in Tables 1 and 2. Hence, the discussion of these discoveries will be limited. Bee County.—Three new gas fields were added during the year: Beeville, discovered by G. M. Church in No. 1 Wood on Sept. 21; Foley, discovered by Dirks Bros. in No. 1 Foley on Feb. 8; and Plummer, discovered by Hynes and Fisher in No. 1 T. M. Plummer on Sept. 2. The three new oil fields added are: Hartzendorf, drilled on fee land by Hartzendorf and completed on May 17 as a small pumper; Ray, southwest of Tuleta, and discovered by Jameson and Burns in No. 1 Campbell

Jan 1, 1936

By W. F. Vietti

Operations in the Texas Gulf Coast during the past year have resulted in the discovery of a number of new fields arid the extension of a few of the older fields, both by deeper drilling and by lateral development. Twenty-six new oil and gas-producing areas and discovery of oil or gas in three subsequently abandoned wells have been recorded for a total of 29 new fields of varying importance. Producing areas at Conroe, Manvel, Greta, Pierce Junction, Hastings, Dirks, Thompson, Batson, Mykawa, Tomball, Raccoon Bend, Samfordyce arid Saxct have been increased. Primary geologic studies followed by geophysical mapping or straight geophysical prospects have been responsible for the more important discoveries. These methods have further proved themselves an aid to limiting wildcatting to the more prospective areas and as the chief means to discover reserves in the future. Production for 1935 totaled 69,560,720 bbl. as compared with 60,850,-360 bbl. for 1934. Strict proration has been in force throughout the discovery of more oil than has been produced. The number of producing oil wells has steadily increased to 4851 at the end of 1935, as compared with 3858 at the end of 1934, owing in part to the prolonged life, because of proration. There were 1272 oil and gas wells completed during 1935, as against 835 in 1934. New Fields Pertinent data on the new fields discovered during 1935 are includrd in Tables 1 and 2. Hence, the discussion of these discoveries will be limited. Bee County.—Three new gas fields were added during the year: Beeville, discovered by G. M. Church in No. 1 Wood on Sept. 21; Foley, discovered by Dirks Bros. in No. 1 Foley on Feb. 8; and Plummer, discovered by Hynes and Fisher in No. 1 T. M. Plummer on Sept. 2. The three new oil fields added are: Hartzendorf, drilled on fee land by Hartzendorf and completed on May 17 as a small pumper; Ray, southwest of Tuleta, and discovered by Jameson and Burns in No. 1 Campbell

Jan 1, 1936