Search Documents

By Masahiro Shimura, Yoshiki Takahama, Toshiyuki Shiraishi, Daisuke Kasai

When advanced high strength steel (AHSS) is rolled at a high reduction ratio, the forward slip ratio in cold rolling tends to be lower than that of the other softer strips such as low-carbon steels, and the work roll sometimes skids the strip. To identify why forward slip ratio of AHSS at a high reduction ratio becomes smaller than that of low-carbon steel, the relationship between the reduction ratio and forward slip ratio was investigated by a rolling experiment. For this trial, a 4Hi laboratory cold mill was used. AHSS and low-carbon steel coils were rolled by two different rolls that were set to 0.3 and 0.6 μmRa to create two types of friction conditions. Furthermore, the rolling conditions were numerically analyzed to determine the influence of friction coefficient and flow stress on the relationship between forward slip ratio and reduction ratio. The experimental investigation and numerical analysis revealed that the forward slip ratio reduced with increasing rolling reduction ratio in a low friction state; contrarily, it increased with increasing rolling reduction ratio in a high friction state. This feature was clearly visible when harder materials were rolled.

Oct 1, 2019

By Erich Bartel

The Kocks Rotation Mill - KRM- is an innovative elongation method for seamless tube production up to 4.5’’ diameter at production levels up to150,000 TPY. Using the principle of cross roll elongation, the machine rotates four rolls around the workpiece. A retained mandrel sets the wall thickness to a precision that exceeds existing industry norms. The KRM process performance has been truly excellent. Attributes include high billet weights, elongation of up to 9.5 in one pass, and eccentricity at or below +/- 5.0%. The flexibility of the process allows a wide range of steel grades to be produced at any wall thickness with little or no mill down time. Surface quality and yield are also greatly improved. Based upon the small foot print of the KRM rotor as well as the simple mandrel manipulation system, the installation cost of the KRM is significantly lower compared to other elongation methods. The reasonable cost of the machine, combined with greatly reduced foundation requirements, reduced ceiling height as well as simple utility connections reduce the initial investment for a new or upgraded mill. Finally, lower roll and mandrel costs allow high quality production at greatly reduces cost/ton.

Aug 16, 2017

By Daniel Antonio Kapper Fabricio

A avaliação das propriedades de mecânica da fratura dos materiais é uma necessidade crescente, sobretudo no setor de óleo e gás. Esse cenário exige a garantia da qualidade na execução de ensaios de tenacidade à fratura. Esse trabalho tem como objetivo realizar uma comparação intralaboratorial para o ensaio de tenacidade à fratura KIC variando o executante do ensaio, visando atender ao requisito de garantia da qualidade da norma NBR ISO/IEC 17025. Os resultados foram comparados através de análise de variância. As diferenças entre os operadores não foram significativas frente ao erro residual a um nível de confiança de 95%, sendo tal resultado considerado satisfatório.

Aug 16, 2017

By José Adilson de Castro

In the integrated steel industries the sintering process plays an important role furnishing raw material to the blast furnace. In this work, a computational simulation of the sinter process is developed that is able to predict the most important phenomena within the sintering bed. The model is based on the multi phase concept with multiple components described by conservation equations of each component coupled with the momentum, chemical reactions and heat transfer. The model validation was carried out comparing the model predictions with averaged industrial data and local temperature measurements within the sinter strand. The model predictions presented good agreement with the averaged values measured on the industrial sinter process.

Aug 2, 2018

By Eduardo Dominguez Trindade

Lubricant oils are subjected to reciprocating movement in the piston ring/cylinder tribocouple of automotive engines. In this kind of movement, the relative speed oscillates between zero and a maximum, and therefore the lubrication regime goes from boundary to hydrodynamic. Tribotests are widely used in laboratories to hint at the friction developed in these systems. In the present work, a SRV tribometer was used to evaluate the friction behaviour of lubricant oils under reciprocating movement up to 60 Hz. A high acquisition rate allowed the analysis of data inside each reciprocating cycle. Both a pure base oil and a fully formulated lubricant were used. Changes in the contact pressure, viscosity and speed were seen to influence friction, which was correlated to the relative thickness predicted by Hamrock-Dowson equation. While some observed characteristics were typical consequences of the Stribeck curve, other effects were also observed, such as the occurrence of seizure at high reciprocating frequency. A lower boundary coefficient of friction due to additive package in the formulated oil was also observed. The results allow a better understanding of friction in reciprocating cycles and can be used to evaluate the performance of oils and surfaces in laboratory prior to engine testing.

Jul 31, 2018

By Marco Antonio Meggiolaro

Notches are preferential sites for fatigue and for environmentally assisted cracking (EAC) initiation. Semi-empirical notch sensitivity factors have been used for a long time to quantify notch effects on fatigue design. Recently, this concept has been mechanically modeled using techniques which properly consider the notch tip stress gradient influence on the fatigue behavior of mechanically short cracks. This model properly calculates such values from the basic fatigue resistances of the material, its fatigue limit and crack growth threshold, considering the characteristics of the notch geometry and of the loading, without the need for any adjustable parameter. Such criteria to estimate notch sensitivity and tolerable short cracks on fatigue have been extended to EAC conditions and verified by proper tests. In its simplest version, the criterion for the maximum tolerable stress under EAC conditions uses the resistances to crack initiation and to large crack propagation and the characteristic short crack size under EAC, considering the crack size and stress intensity factor. Moreover, the tolerance to short cracks under fatigue and under EAC conditions can be unified in an extended Kitagawa-Takahashi diagram, a new and potentially very useful tool for material selection tasks.

Aug 8, 2018

By Evan Thomas

It has been shown before that liquids can slip at a solid boundary, which prompted the idea that parallel-surface bearings can be obtained by the use of alternating slip and non-slip regions in the direction of fluid flow. The amount of slip at the wall depends upon the surface tension at the liquid - solid interface, which in turn depends on the chemical composition of the surface and its roughness. In the present study a heterogeneous surface was created by coating half of a circular glass disc with a coating repellent to glycerol. A rotating glass disc was placed at a known distance above the coated stationary surface and the gap was filled with glycerol. With the top surface moving in the direction of slip to non-slip region, a pressure build up can be theoretically predicted. The pressure gradient in the two regions is constant, similar to that in a Rayleigh step bearing, with the maximum pressure at the boundary. In order to accurately measure the force generated by the pressure increase, a load cell was attached to the heterogeneous disc. Experiments were conducted by varying both sliding speed and distance, and the resultant load carrying capacity was measured and compared with theoretical calculations. This allowed the slip coefficient of the coated surface to be evaluated.

Jul 31, 2018

By Marcelo Rebellato, Beatriz Pereda, Beatriz Lopez, Pello Uranga

The classical application of Nb microalloying in the development of thermomechanical processes for flat products has been related to its suitability to enhance strain-induced precipitation and get a pancaked austenite prior to transformation. As new steel grades or new lay-outs are being developed, more complex metallurgical conditions need to be evaluated. In this context, Nb microalloying, alone or combined with other microadditions, needs to intervene in a more controlled way in additional steps of the thermomechanical process, besides its conventional strain-induced precipitation role. For example, the hardenability enhancement associated with Nb to properly achieve lower temperature transformation products, demands a proper balance of the Nb amount precipitated during rolling and the one remaining in solid solution. Similar effects are also sought when the final available Nb is used to increase strength through precipitation hardening. This manuscript evaluates how changes in the rolling strategies affect the interaction between Nb(C,N) precipitation and austenite recrystallization at different steps of the rolling process. As the possible interactions between parameters intervening simultaneously are quite complex, the application of microstructural models helps to properly define the best austenite conditioning combined with the convenient amount of Nb in solution, as a function of the final property requirements. Along the manuscript, several strategies will be discussed for the case of hot rolling of flat products comparing both normal and coarse initial austenite grain sizes.

Oct 1, 2019

By Henara Lillian Costa

This paper aims to investigate the effects of a possible incorporation of ethanol to the lubricant during engine use on friction and lubricant film thickness, by adding small amounts of ethanol to Group I base (with and without an organic friction modifier) and to formulated oils. Film thickness was measured using ultrathin film interferometry. Friction tests were carried out using a mini-traction machine to obtain Stribeck curves. The film thickness measurements showed that in the region of low speeds, where the elastohydrodynamic film is very thin and therefore boundary lubrication may prevail, the addition of ethanol produced some boundary film, which was not present for the base oils. For the base oil with an organic friction modifier, the presence of ethanol increased the thickness of the low friction boundary film. For the formulated oil, the addition of ethanol reduced film thickness in all lubrication regimes. The friction tests showed some friction reduction due to addition of ethanol to the base oil, in particular at low speeds. For the formulated oil, the addition of ethanol reduced friction at high speeds, which was associated to a reduction in the viscosity of the lubricant, but at low speeds, the presence of ethanol reduced the formation of a boundary layer, increasing friction. For the base oil containing an organic friction modifier, the presence of ethanol increased the range of speeds for which low boundary friction occurred.

Jul 31, 2018

By Ramon Augusto Moretti, Henrique da Rocha Severino, Renato Nascimento de Castro, Fernando Cesar Sousa

Rolling stand 12 (LTx) of long steel, installed in the company A, Piracicaba - SP unit, had presented high levels of vibration, which affected its internal components, such as: shaft, gears and bearings, generating downtime. To evaluate this equipment a study was proposed by the following engineering techniques: Conventional Vibration Analysis, Operational Deflection Shape (ODS) and numerical simulation by the Finite Element Method (FEM). In the Conventional Vibration Analysis, high levels of vibration were observed during manufacturing process, especially when the material reaches the equipment. Impacts generate high values in acceleration, on average 80 m/s² peak to peak. In the moment of impact, misalignment of internal components was observed by ODS. Field results were correlated to those obtained by the Finite Element Method, which allowed to calibrate FEM model. Thus, the most effective structural modification already numerically evaluated was implemented in the system. Afterwards, new measurements by vibration and ODS techniques were performed, and attenuation of vibrational levels and operational mode, which overloaded the internal components rolling stand, were verified.

Oct 1, 2019

By Tiago Salzmann Vilela

No mercado de arames galvanizados destinados a indústria é exigida a uniformidade da camada de zinco sobre o arame. Neste trabalho, foram estudados os efeitos da velocidade de galvanização na uniformidade e espessura da camada de Zinco total, bem como a morfologia das fases de Zn e Ferro-Zinco sobre o substrato metálico. Verificou-se também o efeito do aquecimento após o processo de galvanização, observando o crescimento da camada intermetálica. Finalmente, serão mostradas as principais características de processo obtidas para garantir o atendimento aos ensaios de qualificação, em um estudo de caso de arames galvanizados produzidos em unidade industrial da Gerdau.

Jul 30, 2018

By Dong Maolin

A great amount of high temperature off-gas, whose maximum temperature is up to 2100?, is generated during the smelting process of electric arc furnace (EAF). The dust content, which is mainly iron oxide, of the off-gas is high and worthy of industrial recovery. The heat carried by the high temperature off-gas with dust is about 11% of the total energy input of EAF, and some even is as high as 20%. The high-temperature off-gas not only takes away a lot of heat but also places a huge burden to de-dusting system of EAF. It not only reduces the iron oxide dust recovery ratio, but also causes serious pollution problems. With the development of the iron and steel industry, the proportion of molten iron for EAF gradually increases, and even more than 30% in some cases. The increase of molten iron causes increases in the amount of EAF off-gas and heat waste. As a result the problem of dust removal is worsening [1-2]. How to sufficiently recover the sensible heat of the high temperature off-gas, create conditions for efficient dust removal, thus reduce operating costs of dust removal system and the production costs is a problem which EAF steel making companies must pay attention to.

Oct 30, 2017

By Edgar Ivan Castro Cedeño

En la producción de aceros limpios el control inclusionario es crítico para la obtención de un producto que cumpla con los requerimientos de calidad. El análisis de la distribución de tamaño de inclusión mediante modelos estadísticos permite estimar la incidencia de inclusiones en el producto solidificado a partir de mediciones tomadas en muestras relativamente pequeñas. En seis coladas de acero bajo carbono desoxidado con aluminio se tomaron muestras de acero a lo largo del procesamiento en horno olla y colada continua. Las muestras se prepararon para estimar mediante análisis metalográfico los tamaños de inclusión. Los datos de tamaño de inclusión se analizaron mediante modelos estadísticos de valores extremos, se hace una comparativa entre la distribución Gumbel (que forma parte de la norma ASTM E-2283) y la distribución Generalizada de Valores Extremos (GEV). Mediante una prueba de hipótesis con el estadístico Anderson-Darling, análisis de cuantiles y con la función de supervivencia se demuestra que la población inclusionaria se describe de una mejor manera con la distribución GEV. Finalmente se da un estimado de la incidencia probable de inclusiones en el producto solidificado.

Aug 16, 2017

By Aitor Elorriaga Fernandez de Arroyabe

The purpose of Sinter plants is to heat iron ore fines along with fluxes and coke fines or coal, to produce a semi-molten mass that solidifies into porous pieces of sinter with the needed size and strength. Fluxes used in the sintering process need to have an appropriate size distribution and TI to avoid generation of fines, which could reduce the productivity of the Sinter. Besides, a homogeneous chemical composition and high absorption characteristics are necessary to control the basicity and to combine the flux with P, S, Si, etc, respectively. PASEK Dunite is an ultramaphic rock exploited in the north of Spain with a basic chemical classification, being olivine and serpentine its principal minerals. It is a very homogeneous and hard stone and its main characteristics are: high hot and cold resistance to mechanical stresses, softening and melting points of a flux not of a refractory material. In addition, due to its mechanical and chemical properties, less fines are generated in the sintering process and during the handling and transportation to the blast furnace, improving the productivity of these processes. In this way, the use of PASEK Dunite allows increasing the homogeneity structure of sinter, reducing the percentage of return fines and improving the Sinter productivity.

Oct 30, 2017

By Marcel Antonio Arcari Bassani

In the mining industry, it is common to have data collected in various formats. In an open pit mining operation, at the early stages of exploration samples are obtained from diamond drillholes. During the production stage, samples are collected from blastholes. The last is more numerous but less precise. From a geostatistical view, this dissimilarity has to be considered to integrate the two sources of information. To combine this different data, three methodologies were investigated: simple kriging with local varying mean, cokriging and ordinary kriging. The exhaustive Walker Lake data set was used and it is considered the source to obtain the true grades. Initially, samples were obtained from the exhaustive data set at a regular spacing grid of 20 x 20 meters. Next, samples were obtained again from the exhaustive dataset at a regular spacing of 5 x 5 meters and a relative error of 25% was added. Then, both data were used to estimate blocks using the three methods mentioned. The grade tonnage curves were compared with the true block grade distribution. Moreover, the block misclassification was evaluated. The results showed that ordinary kriging produced estimates closer to the true block grade distribution and reduced the block misclassification.

Aug 8, 2018

By Jianping Li, Fei Peng, Yunbo Xu, Jiayu Li

In this study, in order to achieve ultra-high strength without reducing plasticity, a novel heat treatment involving a pre-quenching process prior to conventional intercritical annealing (P-IDP) was proposed in a low carbon low alloy DP steel. It revealed that abundant fraction of banded structure was observed after conventional intercritical heat treatment (IDP) due to the inheritance of cold rolling deformation. However, the banded structure in novel heat treatment was eliminated significantly, whilst the refined microstructure was relatively more homogeneous with ultrafine ferrite grains. Moreover, obvious chain-networked martensite grains along the ferrite grain boundaries were obtained. The optimum mechanical properties with ultimate strength of 1238 MPa, total elongation of 17%, product of strength and elongation (PSE) of 21GPa% were obtained by P-IDP treatment, which was much higher than the values reported with similar composition. As to pre-quenching treatment, all of grain refinement, homogeneous distribution of martensite islands and precipitated strengthening of microalloyed carbides were beneficial to improve the final strength and ductility.

Oct 1, 2019

By Antonio Adel dos Santos, Carmos Antonio Gandra, Fabricio Mazola da Silva Paiva, Vicente Tadeu Lopes Buono

Abstract Usiminas Steel Plant in Ipatinga installed an accelerated cooling device named CLC (Continuous On-Line Control) in 2010, enabling it to supply steels produced by TMCP (Thermo Mechanical Control Process) technology. This technology complements the TMCR (Thermo Mechanical Control Rolling), with the inclusion of the accelerated cooling process after controlled rolling. There are various gains in terms of quality and productivity associated to the application of such technology. However, the flatness control for API steel becomes crucial because large thermal stresses may be generated due to thermal heterogeneity during the fast cooling when the austenite phase decomposes mostly into ferrite and bainite. In literature, there is lack of knowledge regarding a full understanding of the relation among cooling conditions and plate flatness. Therefore, this work has focused on the effect of the cooling strategy for API steels, aiming at optimizing flatness and keeping the mechanical properties within the specified ranges. The starting point was dilatometer simulation, where cooling conditions such as start cooling temperature, SCT, finish rolling temperature, FRT, and cooling rate, CR, were changed in order to evaluate their effect on microstructure. Those laboratory conditions supposed to give the best results were transposed to industrial scale, so as to produce experimental lots of plates with five different cooling strategies. It was shown the possibility to find a cooling profile that guarantees the balance between mechanical properties and flatness requirements. The influence of cooling strategy on flatness was explained by the varied heat transfer regimes occurring from hot steel surface to the ambient

Oct 1, 2019

By Fabiano Almir Barbosa, Eduardo Alves Machado, Felipe Ferreira Cajano, Bruno Rodrigues Henriques

Spring steels are usually classified as medium to high carbon low alloy steels with very high yield strength, enabling the part to return to its original shape regardless of significant bending or twisting. Despite the fact that plain carbon steels are suitable for small springs, larger and high performance springs usually requires alloy steels such as Cr-V or Si-Mn in order to achieve an even microstructure throughout the cross section. Clutch diaphragm spring is a high performance part that requires very good cleanliness and microstructure homogeneity, thus requiring an alloy steel. In this paper was studied, in an industrial scale, the process parameters and critical characteristics for the development of a Cr and V alloyed high carbon sheet steel for the production of clutch diaphragm spring. The steel was characterized throughout the entire process (casting, hot rolling, cold rolling + batch annealing and heat treated) using tensile test, hardness test, optical microscopy (OM) and scanning electron microscopy (SEM) to assess the mechanical and metallurgical properties of the studied steel. The results have shown the material’s microstructure evolution after each main stage of the process, from a ferrite-bainite/perlite based microstructure as hot band to fully spheroidized as cold-rolled/annealed and then fully martensitic as ready-to-use part.

Oct 1, 2019

By Satish V. Kailas

For product sustainability “closing the cycle” is the first requirement. If the materials used in making the product is not replenished at the rate at which it is being extracted, the cycle is open and the product would not be sustainable. This includes the materials used in generating the energy used to make the product, the transportation, use and disposal. If the materials used in a product, that includes lubricants, is one that cannot be replenished, it has to be recycled for the product to be sustainable. The other basic condition for sustainability is the eco-friendliness of the product. It is argued that the present lubricants do not fall in this category. Using the example of cutting oil emulsions we have shown that it is possible to meet the conditions of sustainability in terms of both the material extraction-replenishment cycle and eco-toxicity. Cutting oil emulsions made from coconut oil and natural additives are shown to have superior cutting properties and are completely eco-friendly. It is concluded that products made using these conditions are possible and is a necessity for man to lead a sustainable life. Closing the cycle, with respect to the energy used in the cycle will make the product completely eco-friendly.

Jul 31, 2018

By Darina Manova

Plasma assisted surface modification methods have been used to nitride stainless steels in order to enhance hardness and therefore the lifetime of industrial components. Nevertheless, the corrosion resistance is not always preserved since it is very sensitive to the process parameters, either in implantation or in thermochemical diffusion techniques. AISI 316L stainless steel was plasma nitrided using three different techniques: Low Energy Ion Implantation (LEII), Plasma Immersion Implantation (PI3) and conventional DC pulsed plasma nitriding (DCPN). For each method several parameters were tested and some of them were selected to achieve the so called S phase of about 3 µm thickness and no nitrides precipitation. The nitrided layer was characterized with OM and SEM. Hardness was assessed on the surface with Vickers indenter and 25 g load. XRD was performed to characterize the S phase and to detect other phases if present and electrochemical corrosion tests were carried out in 3.5% NaCl solution. Although the S phase thickness in the three groups of samples was comparable, hardness was not and neither was the corrosion resistance. The PI3 samples were the hardest with the best performance in corrosion experiments, resulting in a higher breakdown potential and lower currents.

Aug 8, 2018