Search Documents

By Lucas Gonçalves Generoso, Larissa Rodrigues de Carvalho Rocha, Gerson Evaristo de Paula Júnior, Beatriz Fausta Gandra

A eficiência na redução dos minérios de ferro no alto-forno é governada pela estrutura e permeabilidade das camadas de carga. A zona granular do alto-forno é a região onde a carga mantém a sua estrutura estratificada, decorrente do carregamento, sob a forma de grãos sólidos. Nessa região, as condições de permeabilidade determinam o perfil de distribuição do gás e, consequentemente, a eficiência térmica e química do reator. Na Usiminas, foi desenvolvido um ensaio de permeabilidade que permite avaliar a perda de carga em leitos formados pelas matérias-primas utilizadas nos altos-fornos, buscando as condições mais favoráveis ao fluxo gasoso. A partir deste ensaio, foi possível avaliar cargas compostas exclusivamente por sínter, pelota ou minério granulado, ou ainda combinações binárias entre estes. O sínter apresentou a maior perda de carga, seguido da pelota e do minério granulado. Apesar disso, o sínter foi o material que permitiu maior acréscimo de vazão do gás. Os ensaios realizados indicaram que 5% de material com granulometria menor que 5 mm é o limite para a concentração de finos do sínter, situação em que foi observado acréscimo de aproximadamente 50% na resistência à passagem dos gases para as velocidades correspondentes àquelas dos altos-fornos. O leito de melhor permeabilidade foi formado por 95% de sínter e 5% de pelota, seguido pelo de 100% de sínter, sem diferença significativa entre essas condições. Em geral, a combinação de sínter e pelota é mais benéfica para a permeabilidade do leito.

Oct 1, 2019

By HaiWen Luo, Bin Hu

A ultra-high strength medium Mn steel with good ductility was designed and manufactured via the combination of warm rolling and V alloying, which produced not only the extensive precipitation of fine VC particles in both ferrite and austenite but also the bimodal size distribution of retained austenite (RA) grains. A substantial increase of yield strength up to 650 MPa was achieved due to the addition of V without deteriorating ductility. The coarse RA grains firstly transformed to martensite during yielding at the much higher stress threshold, followed by a significant work hardening due to dislocations multiplication, twinning-induced-plasticity (TWIP) and transformation-induced-plasticity (TRIP) in the ultrafine RA grains. The best combination of strength and ductility included 1.5 GPa ultimate tensile strength and 28% total elongation. This was achieved due to the sustainable TRIP and TWIP effects in the later straining stage resulting from the ultrafine austenite grains, the latter were reversely transformed from the recrystallized ferrite grains.

Oct 1, 2019

By Patrick E. Connell

During the ABM Conference of 2015 the latest design and process features of the new 3-roll RSB® generation were presented together with a unique Size Control System SCS® for a real time closed loop control to produce an extraordinary quality SBQ – day in, day out. In the past two years, Kocks has focused on improving the repeatability of the rolling process and developed technology to enhance the performance of its equipment. These developments include Fast Remote Control (FRC), Stands Adjustable Under Load (AUL) implementation of closed loop Size Control System (SCS), and finally a state of the art laser Gauge (4D Eagle) that pulls all of these developments into a complete package of quality. Gauges used in the past generally operated with the “shadow” measuring system. The latest gauge developments are based on the “light section” method. This method is more suitable to provide real time measurement parameters of the rolled bar. Placed close to the last rolling stand, the “light section” gauge is capable of measuring around the complete diameter with a clear definition of the bar stage in relation to the axes of the rolls. It is also capable of making these measurements using a very high measurement frequency. Following requirements of the market, requiring the highest gauge measuring frequencies which display the bar in the most accurate way even at the highest rolling speeds, the “4D Eagle” gauge was developed. This paper describes all the process features and parameters of this impressive and unique newly developed gauge as well as the other described technical improvements.

Oct 30, 2017

By José Fagundes Jr., Juliano Braz Possatti, Bruno Câmara Vieira, Gabriel Godinho Alves, Bruno Bastos da Silva Murad, Cristina Maria de Oliveira Roque

Driven by market trends, increasing environmental accountability, government regulations and fostered by the Company’s strategic plan, ArcelorMittal Tubarão has developed new steel products to deliver better solutions to fit each customer’s needs. This often translates in higher strength, more complex and dimensionally challenging (thinner and wider) steels to attend a broad array of goals, such as reduction of vehicles fuel consumption and carbon emissions, increase in fatigue performance of heat treated parts, higher load capacity per net weight in vessels or wagons and lower supplying lead time as ArcelorMittal Tubarão establishes itself as a domestic option for so far imported grades. Based on the annual Product Development Plan, a structured workflow involves technical discussions from an operational point of view about safety issues, metallurgical project, steel grade family definitions, offline simulations prior to field trials, deformation resistance and process parameters adjustments and scheduling strategy. As a result of the increasing synergy between the areas, the share of new materials developed in recent years has been sustainably increased up to 15% in 2018, adding value to the final product without impact on hot rolled coil output and with a low cobble index.

Oct 1, 2019

By Martim Hideki Nakayama Kurauchi

One of the main issues regarding the use of charcoal in metallurgical processes is its mechanical strength, which is much lower than coke. There is no defined standard to determine charcoal compression strength, and the methods described in the literature consist in using a prepared specimen and applying compressing load in the same direction of the charcoal fibres. As charcoal is highly anisotropic, it is proposed a procedure that does not use a specimen and with load applied on a specific direction. Instead, it intends to simulate industrial conditions by randomly dumping charcoal inside a tube, without preferential directional arrangement. This is an attempt to determine charcoal mechanical strength and predict the behaviour of bulk charcoal under a static load, as in a blast furnace. Experiments with controlled loads have been carried out on randomly distributed bulk charcoal with controlled initial size and their effect on the size distribution has been analysed. After compression, charcoal is screened and each size is weighed, determining the particle size distribution of the experiment. This method can therefore be used to evaluate charcoal mechanical strength.

Aug 1, 2018

By J. N. Stevens, M. Tulwin, P. J. Lawlor

All metals producers are on an unending search for a competitive advantage. They need to produce in the most cost effective way. Sometimes a new mill might be considered but in this paper we present examples of how this might not always be necessary. A detailed investigation by an equipment vendor who can consider the mill and or plant as a complete entity: mechanics, automation and process control can often find solutions that are both lower cost and can be implemented in shorter time frames.

Oct 1, 2019

By Henrique Lacerda Eleutério, Aldo Henrique de Almeida Barbosa, Vicente Tadeu Lopes Buono

The automotive industry’s interest in galvannealed (GA) boron steel for hot forming processes application has been steadily increasing due to its excellent surface quality, galvanic protection provided to the parts, good paint adhesion and better weldability in relation to other coatings for this application. In this study, samples of 22MnB5 galvannealed steel were heat treated and hot stamped on a water cooled die in laboratory scale. The influence of heat treatment on stability of coating and steel was assessed by using initial heating rates 11.0ºC/s and 15.0ºC/s. Microstructural evolution of galvannealed coating and structural integrity of steel during hot forming were investigated by scanning electron microscopy with energy dispersive spectroscopy analysis (SEM/EDS/Line scan), X-ray diffraction (XRD) and optical microscopy (OM). It was possible to quantify the Fe-Zn phase evolution during hot forming, to understand the effect of these heating rates on the product properties and to establish an optimized heat treatment for hot forming of these steel. The heat treatment with the heating rate of 15.0ºC/s presented greater operational flexibility and final products free from surface defects or cracks in the substrate.

Oct 1, 2019

By Foluke Salgado de Assis

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and environmental correct material with respect to CO2 emission. The banana fiber is nowadays recognized by its mechanical properties. It is known that with the increase of fibers volume fraction the composite significant increases its tensile strength. This was obtained with amounts up to 30% in volume of banana fiber. However no higher volume of fibers was able to be molded in a composite plate until now. Thus the present work aims to study higher volumes of fiber in terms of the influence on the tensile strength of specimens prepared under 5 tons of pressure. The fibers were previously washed and dried in an oven at 60ºC, after that poured together with the epoxy resin and catalyst mixture in the metal molds bone-shaped, and pressured to ensure specimens quality. The tensile strength increased significantly with higher amounts of banana fiber incorporated in the epoxy matrix. This better performance can be directly related to the fracture obstacle imposed by the fibers as well as the type of cracks resulting from the fiber/matrix interaction.

Aug 16, 2017

By Carolina Gomes Dias Ribeiro

The modern composite materials, especially those reinforced with synthetic fibers such as glass and carbon, have been used since last century to attend the demands required by most technological fields, from home appliances to aerospace. Natural fibers composites with biodegradable polymer matrices are considered environmentally friendly materials and currently accepted as possible substitutes for synthetic composites. These green composites can be safely discarded or composted at the end of their life without harm to the environment. Another alternative for synthetic composites is to apply natural lignocellulosic fibers as reinforcement of conventional polymer matrices and already used in the automobile industry. In addition to the environmental and societal advantages of the green composites, the lignocellulosic fiber reinforced conventional polymer composite also has economical and technical advantages. In the case of a fiber collected as a waste, the price of the composite can be considerably lower than “fiberglass”. Furthermore, with high strength lignocellulosic fibers such as sisal, ramie and malva the specific strength of a composite may approach that of “fiberglass”. Therefore the objective of the present work is to investigate the mechanical behavior of polymer matrix composites reinforced with high volumes of natural malva fibers subjected to tensile stresses.

Aug 16, 2017

By Mariano de Córdova

In this paper, the coke oven life prolongation technology is reviewed from different points of view: blend design; battery heating; operational control; refractory maintenance. A summary of major inspections in critical areas, for the evaluation of the battery conservation situation is presented. A discussion on tools for the diagnostics of the degree of damage is carried out.

Aug 16, 2017

By D. A. Aranda-Regino, C. Gómez-de-la-Garza, J. Ramírez-Cuellar, L. A. Leduc-Lezama

The Pickling Line Tandem Cold Mill (PLTCM) at Ternium’s Pesqueria plant with a 5 stands, 6 high configuration started in 2013. At the time of the start up the work roll specification and grinding practices were stablished following a low risk policy to be able to sustain any start-up associated accident. Once a stable operation has been achieved both these policies are being modified to improve productivity and reduce costs. The specified hardness of the rolls has been increased and efforts are being made to optimize the grinding according to the rolling campaign length and materials. The fatigue damage in work rolls, after rolling and its removal by grinding was followed by hardness measurements made at the end of the rolling campaign and after grinding. Softening of the rolls after rolling was found mainly in final stands to be related to the averaged stress experienced during the campaign, the original roll hardness was recovered after grinding. Hardness evolution was also followed after each grinding step finding that the total amount of grinding could be reduced. The grinding practice was modified accordingly for the first stands and the yield of work rolls in them has improved.

Oct 1, 2019

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017

By Hugo M. Checo

Friction-reducing textures for lubricated mechanisms have received much attention since the advent of microtexturing techniques. In this work we consider the piston ring/liner contact, numerically simulating the rings as they slide against a textured liner. This situation has not been sufficiently analyzed because its numerical complexity is much greater than that of texturing the rings. Further, we consider the actual typical geometries of oil-control, wiper and compression rings, under realistic loads and velocities. The results show the possibility of friction reduction when the texture on the liner is properly designed, identifying starvation alleviation as a crucial intervening mechanism.

Jul 31, 2018

By Breno Totti Maia

Para uma boa operação das lanças de oxigênio para convertedores BOF é necessário existir uma boa condição de refrigeração, devido à agressividade existente no ambiente, onde ela fica exposta a condições de alta radiação, gases a alta temperatura e, algumas vezes, com o aço líquido. Para uma boa refrigeração, basicamente são necessários uma boa qualidade de água e condições adequadas de vazão e pressão. Mas somente esses fatores podem não garantir o desempenho adequado às condições de escoamento da água, devido à complexidade geométrica do bico da lança. Esse artigo tem como objetivo apresentar um estudo comparativo de escoamento da água, na parte crítica de uma lança que é o bico, destacando a importância da geometria interna do bico na troca térmica do equipamento. Serão apresentados os resultados comparativos, onde se observa que otimização do escoamento interno no bico da lança aumenta a vida útil do equipamento.

Jul 29, 2018

By Matteo Tomba

Today’s steel market is characterised by high competitiveness and tight profit margins; therefore, the operational costs of rolling mills must be as low as possible, while ensuring a final product of the highest quality standards. PERT SRL is an engineering company with a long-term experience in the international steel market, specialised in the design and supply of highly innovative and bespoke solutions for siderurgical and environmental plants. Because of its strong commitment to deliver excellent products and services, and its ability to innovate and adapt to the fastchanging market requirements, PERT has studied a new generation of BI-SUPPORT rolling stands, designed to be used in rolling mill plants for the production of rebars, rounds and sections in special quality bars (SBQ) steel grade, wire rod, light and medium section, suitable also for special steel plants. This paper will provide a deep insight into the key technical and economic features that have revolutionised the rolling technology for long products, such as the absence of spindles and piping on board, the considerably reduced number of spare parts required, a ring gap regulation system, and the compact dimensions, which lead to significant savings in investments and production costs; at the same time, the BI-SUPPORT stands guarantee excellent standards to the final product, an increase in plant productivity and a general improvement in the plant management.

Aug 16, 2017

By Daniela Fátima Gomes

O processo de têmpera é uma das etapas críticas na produção de tubos de aço, possuindo grande importância na determinação da qualidade do produto final. Nesse trabalho foi desenvolvido um modelo matemático para o resfriamento de um tubo submetido a têmpera por anéis. Neste processo, o tubo passa através de um conjunto de anéis com sprays de água. Uma série de variáveis afetam a performance do processo, tais como: temperatura de entrada do material na estrutura de resfriamento e velocidades de rotação e avanço do tubo. Diversas simulações foram desenvolvidas, comparando diferentes abordagens para a modelagem. Constatou-se que o espaçamento entre os anéis causa grandes gradientes de temperatura ao longo da superfície do tubo. Verificou-se que a transferência de calor ao longo do comprimento do tubo não deve ser negligenciada e a velocidade de rotação do tubo uniformiza a temperatura ao longo da direção angular do tubo.

Oct 30, 2017

By Giselle de Mattos Araújo

A autorredução é afetada por características das matérias-primas tais como granulometria, porosidade, tipo e teor da fonte carbonácea, e também por características do ciclo de processamento imposto, taxas de aquecimento, tipo de atmosfera gasosa, temperatura média de processo. No presente trabalho objetiva-se, através de testes de termogravimetria, avaliar a cinética de autorredução e também o fluxo térmico associado, durante o processamento de diversas associações de finos de minério e fonte carbonácea. Com os resultados obtidos identificam-se condições que otimizam tanto a mistura autorredutora quanto o processamento, observando-se que em uma mesma faixa granulométrica, o maior conteúdo de Cfixo da fonte carbonácea e materiais mais reativos otimizam a cinética, em detrimento da maior quantidade volumétrica de partículas carbonáceas observada em amostras contendo carvões mais pobres em Cfixo. Taxas adequadamente controladas permitem a definição de instantes distintos para as diversas etapas fenomenológicas envolvidas no processamento da autorredução.

Aug 2, 2018

By Flávia Vieira Braga

O efeito da temperatura de deformação a quente na textura cristalográfica de um aço inoxidável ferrítico AISI 430 estabilizado ao Nióbio foi estudado por ensaios de torção a quente. A laminação de acabamento em laminador Steckel foi simulada utilizando diferentes faixas de temperatura, buscando promover o amaciamento por recristalização. Após cada ensaio, as amostras foram temperadas até a temperatura ambiente objetivando a análise das microestruturas geradas. Foram também realizados ensaios de torção interrompidos visando avaliar a ocorrência da recristalização entre passes. A técnica de EBSD foi utilizada para analisar a microestrutura das amostras ensaiadas, a textura formada e o tamanho de grão. Foi observado que a de temperatura de simulação que mais favorece a ocorrência da recristalização estática está entre 900 e 840 ºC e o tamanho de grão resultante é menor em tais condições. A textura de torção obtida está em concordância com a literatura.

Aug 16, 2017

By Gilvandro Bueno

Atualmente, diferentes tipos de vedações laterais de rolos, usados para limitar o efeito de borda em prensas de rolos “High Pressure Grinding Rolls (HPGR)” se encontram disponíveis. O presente trabalho comparou dois métodos usados na vedação lateral: as placas laterais (cheek plates) e as flanges, essas últimas colocadas em um dos dois rolos, a partir de simulações usando o Método dos Elementos Discretos "Discrete Element Method (DEM)", com acoplamento dinâmico multicorpos (Multibody dynamics ou MBD). Como resultado das simulações foram obtidos os perfis de força compressiva ao longo do rolo, assim como a proporção do fluxo mássico de alimentação que é projetado fora da zona de compressão durante a prensagem. As simulações mostraram que ...do HPGR usando o DEM + MBD se apresentam como uma ferramenta muito útil para visualizar o melhor modelo de vedação de modo a minimizar o efeito de borda durante o processo de prensagem.

Oct 30, 2017

By Raelly Laurinda Araujo da Silva

As ligas de alumínio são utilizadas mundialmente em inúmeras atividades. Com o aumento da competitividade, existe a necessidade de melhoria constante no processo produtivo. Essas melhorias têm como objetivo reduzir custos e melhorar o desempenho dos componentes e têm sido realizadas pela aplicação de novas técnicas e pelo desenvolvimento de novas ligas/composições. O processo squeeze casting é um processo inovador dentro dos processos de fundição, no qual o metal vazado no estado liquido é solidificado sob pressão dentro de uma coquilha metálica fechada por um punção. Neste contexto, o presente trabalho buscou analisar a influência da aplicação de diferentes pressões no processo de squeeze casting na modificação estrutural da liga de alumínio do tipo AlSi1Mg0.5Mn. Os resultados indicam que o aumento da pressão na liga gera uma taxa de transferência de calor mais elevada que reduziu o tempo de solidificação modificando a microestrutura.

Oct 30, 2017