Search Documents

During the last 20 years, more than 80 km (50 miles) of tunnels have been constructed in the Los Angeles, CA area. Recent projects include The East Central Interceptor Sewer (ECIS), completed in 2004. It spans more than 18 km (11 miles). The Northeast Interceptor Sewer (NEIS), completed in 2005, spans 11 km (7 miles). And the 2-km (1.3-mile) Metropolitan Transportation Authority?s Gold Line Eastside Extension (MCGLEE) was completed in 2006. All of the tunnel routes lay beneath heavily populated urban environments so minimizing ground surface settlement was critical to the success of the projects. Previous tunneling efforts in the Los Angeles area using open shield methods resulted in significant settlement that damaged roads, utilities, buildings and other structures. Earth pressure balance (EPB), or slurry machines, were specified for these projects to reduce subsidence risk. The contractors chose EPB tunnel boring machines (TBM) for the work. The closed and pressured face of the EPB TBM reduces loss of ground at the tunnel face and, when the machines are used in combination with gasketed pre-cast tunnel liners and backfill grout behind the installed segments, losses from over-cut of the excavated surface are also reduced.

Jan 1, 2008

By R Adamian, F. T. Da Silva, D. H. Gameiro

Schytill and Geldart diagrams were developed for the TiO2-C-Cl2 system at 1 073 and 1 273 K, so as to define the hypothetical relations between particle sizes and chlorine velocity for simultaneous fluidisation of mixtures of anatase concentrate and charcoal for carbochlorination. It was concluded that the operating limits on chlorine gas velocity will be controlled by the behaviour of the reducing agent, mainly because of its lower density. An increase in temperature from 1 073 to 1 273 K will have only a small influence on the fluid-dynamic behaviour of the mixture. For bubble fluidisation, the maximum sizes 0.413-0.478 mm for anatase and 0.529-0.611 mm for charcoal will be adequate. When the particle size distribution is large, fluidisation will be feasible only if conducted in two stages, otherwise the residence time of the small particles in the reactor will be very short. New diagrams will be needed for the gaseous chlorides in the second stage

Jun 21, 1905

By D. C. Oliver

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Metallurgy and Materials) degree Corrosion in exhaust systems can occur on both the interior and exterior surfaces. Chloride-containing de-icing salts on the roads in colder countries greatly increases the rate of corrosion on the exterior surfaces. This paper investigates the relative exterior corrosion resistance of three alloys?two ferritic stainless steels( AISI Types 409 and 441) and an aluminized mild steel. The exhaust system is split into two categories?the hot end and the cold end. A test for each of these ends was designed?the standard ASTM G85test was modified to create a simulated driving cycle. The cold end test samples were exposed to ten driving cycles, and the hot end test samples were exposed to five driving cycles. A driving cycle constitutes the car being started from cold, driven until the operating temperatures are reached, and switched off and allowed to cool. Pitting corrosion is the primary corrosion mechanism occurring at the cold end of the exhaust system. The aluminized mild steel was the most resistant alloy in this test, and Type 409 the least. However, once the protective aluminium layer degrades, corrosion will occur rapidly. At the hot end of the exhaust system, spalling of the surface oxide layer is the primary corrosion mechanism occurring. Type 441 was the most resistant in this test, and the aluminized mild steel the least resistant. Potentiodynamic tests were performed on the alloys?the results agreed with the results obtained in the exposure tests.

Jan 1, 2003

By F. M. Boler

The U.S. Bureau of Mines conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic de stressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 2 ½ -week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 2010

Prof. A. Ledebur, Freiberg, Saxony :* Mr. Sauveur has presented and enriched with original observations a valuable summary of the theories advanced hitherto concerning the hardening of steel; but in one particular, it seems to me, his statements call for correction. He says:

Jan 1, 1898

By Frank Cook

In this two-year study, an evaluation of mining and reclamation practices at 159 randomly sampled surface coal mines in the United States was conducted. It is concluded that reclamation practices in most of the 22 coal-producing states were adequate during 1975, but that improvement in reclamation performance was desirable in the acid area of the central U. S. and in mountainous southwestern Virginia. Productivity improvements should result from research to determine efficient or optimal operating procedures for dragline stripping of single and multiple seams, surface mining of lignite, multicut and multiseam haulback mining on steep slopes, mountaintop removal, and surface mining in swampy or deeply glaciated areas. Specific candidate research projects are discussed in this report.

Jan 1, 1976

By Alan R. Buehler

The Bureau of Mines conducted a mineral investigation of the 177,000-acre Secesh study area; most of the area had been proposed as wilderness. Bureau personnel mapped and sampled several hundred mine and prospect workings; 1,715 rock, soil, and placer samples were taken during the investigation. The study area is centered about 25 mi east-northeast of McCall, Idaho, in the Payette National Forest. Five mining districts extend into or are adjacent to the study area. There have been more than 3,000 mining claims located inside the study area, 884 are current. In excess of $17 million (historical value) in placer and lode gold has reportedly been produced from the Warren district alone. The study area contains gold, silver, copper, lead, zinc, tungsten, and antimony. At least six properties that would be in the proposed wilderness contain gold resources; more than 18 million tons averaging 0.038 oz/ton gold have been identified. Additional resources may be located at 4 other localities. The 4th of July mine is currently producing gold/silver/lead ore. Similar resources may be located on at least 3 other properties. Placer samples from the study area contained up to 0.34 oz gold/yd3 ($120/yd3). The samples are representative of relatively small occurrences and do not constitute resources; small quantities of gold may be recovered by recreational placer miners.

Jan 1, 1993

By A. Opara

The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium [Se], which are introduced to seepage waters. Nitrogen species, such as nitrate and ammonia, are also found in association with coal-mining drainages mainly due to leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal mining environments in British Columbia, with values ranging from below 50 to over 500 µg/L in site waters. Selenate is the most common form of selenium found in waste rock seepages, and is exceedingly mobile in aerobic freshwaters. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains. Treatment to remove Se from coal-mining wastewaters has proven to be challenging for conventional water treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry. The Electro-Biochemical Reactor (EBR) technology provides electrons to the microbes directly at a low voltage potential (1-3 V), supplying a controllable and consistent supply of useable electrons to the system and microbes at low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical, and robust biotreatment system than found in past generations of biological treatment systems. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required. Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal mine wastewaters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia?s coal-mining wastewaters.

Feb 23, 2014

By A. Opara

The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium [Se], which are introduced to seepage waters. Nitrogen species, such as nitrate and ammonia, are also found in association with coal-mining drainages mainly due to leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal mining environments in British Columbia, with values ranging from below 50 to over 500 µg/L in site waters. Selenate is the most common form of selenium found in waste rock seepages, and is exceedingly mobile in aerobic freshwaters. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains. Treatment to remove Se from coal-mining wastewaters has proven to be challenging for conventional water treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry. The Electro-Biochemical Reactor (EBR) technology provides electrons to the microbes directly at a low voltage potential (1-3 V), supplying a controllable and consistent supply of useable electrons to the system and microbes at low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical, and robust biotreatment system than found in past generations of biological treatment systems. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required. Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal mine wastewaters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia?s coal-mining wastewaters.

Feb 23, 2014

By J. J. Jakosky

THE method of electrical mapping of oil structures to be described possesses certain limitations, as well as certain definite advantages. It, in common with other geophysical methods, is not a panacea for the solution of all subsurface geological problems. It operates on differences in electrical conductivity of the geological strata, whereas the other most-used methods operate on (1) differences in magnetic properties, (2) differences in gravimetric properties, or (3) differences in seismic properties. This modification of the resistivity method is therefore able to obtain subsurface information under conditions not favorable to the other methods mentioned. Where the other methods have been employed with ambiguous results it may act as a complementary method.

Jan 1, 1936

By Jörn M. Seitz

Dynamic load testing is employed with ever increasing frequency to estimate the strength and elastic settlement behavior of piles of all types. For dynamic loading ram masses up to 20 Mg have been used and pile resistance forces up to 30 MN have been activated. Strains and accelerations induced by the impact are measured near the pile top and a load-set curve is computed by the so-called CAPWAP method. This paper briefly describes both the necessary equipment and other details of the dynamic tests and the available analytical tools for data interpretation. Furthermore the need for further research and the current status of standardization will be discussed. This paper also presents the results from several static and dynamic correlation tests on cast-in-situ piles of up to 2 m diameter and 64 m length. The results demonstrate the economical and technical feasibility of this test method.

Jan 1, 1987

By Paul Staples, Chris Morley

"The development of the Cerro Verde, Amplats Mogalakwena and Boddington projects over the last few years has helped to establish the use of high pressure grinding rolls (HPGR) in comminution circuit designs in large-scale hard-rock applications. The increasing acceptance of this innovative and sometimes controversial technology has had the natural effect of prompting many other new projects to examine HPGR as an alternative to the established, usually SAG-based, comminution circuit design approach.At the current stage of development of the technology, HPGR-based circuit capital costs are generally higher than for the equivalent SAG-based circuit, so that HPGR must offer sufficient operating cost benefits to offset the additional capital costs over an acceptable pay-back period. It is usually necessary to undertake comprehensive project-specific trade-off studies to quantify this effect.This paper describes the processes involved in the execution of a typical SAG-HPGR trade-off study, from the preliminary assessment of ore characteristics and project criteria, through testwork, circuit modelling, equipment selection and cost estimates, to a project-economics comparative assessment of the options. The trade-off study determines both the technical feasibility of the respective technologies and their commercial viability in the given project setting.The paper concludes with a cautionary note to the effect that, while HPGR has many potential benefits, it is not a panacea, and that, for some ore types and project conditions, the more established conventional technologies are often more appropriate."

Jan 1, 2010

By D. A. Rhys, M. Sieb, M. A. Prefontaine, C. L. Swanson, S. R. Frostad, H. Q. Smit

"Gold-silver mineralization at Red Mountain (1992 resource of 2.5 million tonnes grading 12.8 g/t Au and 38.1 g/t Ag) occurs within several discrete zones within a folded sequence of Middle to Late Triassic Triassic sedimentary rocks, Early Jurassic volcaniclastic and pyroclastic rocks, and Early Jurassic intrusions. Three phases of Early Jurassic sills and stocks collectively comprise the Golds/ide intrusions: (1) irregular bodies of medium-grained hornblende monzodiorite (Hillside porphyry); (2) hornblende-biotite + quartz porphyritic monzodiorite to quartz monzodiorite (Golds/ide porphyry; U-Pb zircon ages of 197.1 + 1.9 Ma); and (3) biotite porphyritic hornblende monzodiorite sills (Biotite porphyry). Contact breccias and igneous breccia dikes are common features of the Golds/ide intrusions. Chemical similarities and equivalent ages of volcanic rocks and intrusions, and the presence of intrusive clasts in volcanic rocks suggest that the intrusions are feeders to overlying volcanic units.Hydrothermal alteration affects all pre-Tertiary rocks on Red Mountain, including all phases of the Golds/ide intrusions. Several shallow-dipping alteration zones are developed sequentially above a propylitic quartz stockwork/molybdenum zone. These include: (1) sericite-quartz-pyrite alteration (pyrite-dominant alteration); (2) chlorite-K-feldspar-sericite-titanite alteration with disseminated and vein pyrrhotite (pyrrhotite-dominant alteration); and (3) brown to black tourmaline veins and K-feldspar-pyrite-titanite-actinolite alteration. Anomalous gold(> 0.3 g/t) mineralization is developed at the transition from the pyrite to the pyrrhotite dominant alteration over a > 1 km2 area. Within this anomalous zone, high-grade (3 g/t to 20 g/t Au) gold-silver mineralization occurs in 5 m to 29 m thick, semi-tabular pyrite + pyrrhotite stockworks with intense sericitic alteration and surrounding disseminated sphalerite + pyrrhotite.Stratigraphic, spatial and geochronologic relations and alteration zoning indicate that mineralization formed in a subvolcanic environment at the top of the Golds/ide intrusions and at the base of the Early Jurassic volcanic pile. The Golds/ide porphyry is interpreted to be the mineralizing intrusion. The alteration zoning, molybdenum-copper mineralized quartz stockworks, extensive Ksilicate and tourmaline alteration, and the relationship with a hypabyssal porphyritic intrusion show similarities to many porphyry systems."

Jan 1, 1995

The conclusions reached by den Tex after a study of the fabric of some rocks from Broken Hill have been used to support the epigenetic hypothesis for the origin of the ore, first by Edwards (1959, p. 70) and then by Stillwell (1962, p. 131) in his criticism of Segnit's (1961) views. Den Tex claimed that the petrofabric study provided "independent evidence that the ore, at least in its present form, post-dates all events of a diastrophic nature in the area concerned".Repetition of this claim by Edwards and by Stillwell and the lack of any criticism of den Tex's work for more than three years implies its general acceptance by geologists in Australia. Therefore it appears necessary to examine parts of den Tex's paper in detail to show that his, conclusions are unwarranted. The major weaknesses in his study are that1. the petrofabric study was inadequate to warrant any major conclusions, and2. the petrofabric data allow alternative conclusions.Den Tex made a single visit to the field, collected six carefully selected specimens and presented quartz and· biotitepetrofabric diagrams for two specimens, quartz-diagrams alone for three more and included three diagrams of the orientation of c-axes and fractures in one specimen. It is not reasonable to come to firm conclusions about the origin of such a complex area as Broken Hill on such inadequate data, despite den Tex's claim (p. 87, lines 22 and 23) that "a thorough investigation of the quartz-fabric of the wall rock was undertaken".Den Tex's interpretation of each diagram is open to criticism, and alternative (and to my mind, preferable) interpretations may be made. It is impossible to evaluate den...

Jan 1, 1962

By C. C. Merrill

The Bureau of Mines beneficiated the wastes generated by commercial titanium chlorination operations to reclaim metal values and reduce the problem of disposing of solid wastes. A water leach solubilized about 40 percent of the dry weight and over 75 percent of the metallic impurities. The residue from the water leach was rich in titanium dioxide and carbon; it was combined with rutile and recycled to a laboratory chlorinator. The contained carbon was used in lieu of part of the coke requirement.

Jan 1, 1969

By Zhang Libo, Peng Jinhui, Zhang Zhengfu, Fu Mengbi, Han Yamei

In this paper, results of a novel synthesis method of carbon-coated LiNi113Mn113Co11302 cathode material for lithium-ion battery are reported. The carbon coating was produced from a precursor, glucose, by microwave-pyrolysis method. The structure, morphology and electrochemical performance of the bare and carbon-coated LiNi113Mn113Co11302 were characterized by X-ray diffraction, scanning electron microscopy and charge-discharge tests respectively. The L8(27) orthogonal experiments were carried out to optimize LiNi113Co113Mn1130z/C technological conditions. The conditions of the orthogonal experiments were that the glucose content were 1.5 % and 4 %, the holding time were 15min and 30min, the heating temperature were 400 °C and 500 °C and the solvent were H20 and CH3CH20H. The main experiment target include specific capacity at 0.1C and 0.2C, Capacity retention rate, medium voltage attenuation rate and The fifth discharge medium voltage. The data were analyzed by Minitab 14 statistics software. The results of analysis of variance indicated that the most influential factor was the glucose content despite of discharge rate. Secondly, the effect of the solvent was equivalent to the holding time.

Jan 1, 2013

By Bradford F. Townsend, Matthew E. Fowler, Michael F. Smithson, Lawrence R. Eckert

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2010

By Jesús E. Gómez

This work is a continuation of a paper presented in the 32nd DFI Annual Conference, Colorado 2007, titled ?Hollow Core Bar Micropiles - Design parameters interpreted from 260 load tests.? The first paper presented the results of the verification and proof tests performed for the retrofit of two bridges with hollow core bars that used 260 micropiles. It included an interpretation of the unit bond values in the different soils where micropiles were installed. Recently two additional bridges within the same geological environment were also retrofitted using 144 hollow core micropiles. This paper includes the interpretation of the additional data from the proof tests performed and refines recommended values for design of hollow core bar micropiles in soils similar to those encountered in these two projects. The authors believe that the data collected will significantly add to the relatively small existing database on micropile tests and may also be useful during implementation of the LRFD design methodology.

Jan 1, 2008

By S. L. Huang

The location and shape of potential failure surfaces in soil slopes were directly determined based on the stresses induced in the soil mass and the strength of the soil itself. Stress calculations were carried out by the finite element method with the Drucker-Prager nonlinear material model. The Mohr-Coulomb failure criterion and Mohr's circle stress analysis were then applied to the calculated stresses to determine the characteristics of the failure surface.

Jan 1, 1989

By Oliver Bowles

Under a cooperative agreement between the Bureau of Mines, the United States Geological Survey, and the United States Bureau of Standards, a study of the stone-quarrying industries of the country was begun in 1914. The results of investigations made have been published from time to time.1 During the World War the Bureau of Mines centered its attention on problems relating to national defense, and detailed studies of stone-quarry problems were not undertaken except for an investigation of labor saving at limestone quarries, reported in Technical Paper 203, which related to a question of military importance. Since the return of peace, the high cost of materials and labor has made more imperative than in prewar times the conduct of investigations for aiding the quarrying industries in every way possible to adopt more economical methods and to utilize the most efficient labor-saving equipment. The publications already issued have had a wide demand, and in the interest of the quarry industries the bureau proposes to issue additions to the series as rapidly as funds are available. In an endeavor to promote economy and the reduction of waste in the slate industry, a study of slate quarrying was begun in 1920 and covered a period of about two years. Sixty-five active quarries were visited, and a detailed study made of all problems bearing on their successful operation. Field study was supplemented by a study of all information available in books or published articles on slate quarrying.

Jan 1, 1922