Search Documents

By R. R. Joseph, K. A. Gschneidner

The solid solubility of magnesium in the close-packed modifications of lanthanum, cerium, praseodymium, neodymium, gadolinium, dysprosium, and lutetium was determined from approximately 250°C to the eutectoid temperature by the X-ray parametric technique. The maximum solubility at the eutectoid temperature was found to be 9.4 at. pet in La, 8.2 in Ce, 9.2 in Pr, 8.2 in Nd, 14.1 in Gd, 13.5 in Dy, and 11.5 in Lu. The solubility when compared at a homologous temperature was found to increase in a smooth manner with decreasing size factor from lanthanum to lutetium. It was found that the apparent atomic radius of magnesium when dissolved in the lanthanide solvent was constant and could be accounted for by consideration of several models dealing with departures from Vegard's law. The eutectoid temperatures for the lanthanide-rich La-Mg, Ce-Mg, and Nd-Mg systems were found to be 544", 505°, and 551°c, respectively. A study of the solid solubility of magnesium in the lanthanide metals was initiated because the valency and electron egativity difference are essentially constant and favorable for solid-solution formation, and thus one could examine the effect of size on terminal solid solutions. The size factors based on metal radii range from 14.6 pet for lanthanum to 7.5 pet for lutetium. Since the electronegativity difference is small, 0.06 unit or less, application of the Hume-~othery' and Darken and Gurry2 criteria for solid-solution formation indicates that the solubility of magnesium would be expected to be small for lanthanum (between 5 and 10 at. pet) and to increase as we proceed along the lanthanide series. A search of the literature revealed no data on the solubility of magnesium in the lanthanide metals except for the solubility of magnesium in cerium at 450oCA typical phase diagram for the lanthanide-rich end of the lanthanide-magnesium phase diagram is shown in Fig. 1. EXPERIMENTAL PROCEDURES Preparation of Alloys. The lanthanide metals used in the preparation of alloys for this investigation were prepared from the corresponding fluoride by metallothermic reduction techniques previously described by Daane.4 The chemical analyses of the metals used are listed in Table I.

Jan 1, 1965

By Thomas P. Mucho, Thomas M. Barczak, Dennis R. Dolinar

Maintaining ground stability in the gate roads, particularly the tailgate, has always been critical to the success of longwall mining, both in terms of safety and productivity. Several new support technologies have been developed in recent years to replace conventional wood and concrete cribbing for secondary roof support. Since their performance characteristics are unique, the best practices that have been developed with conventional wood cribbing may not be applicable for these alternative support technologies. Therefore, with so many options to consider and the importance of achieving adequate ground control at minimal cost, the trial-and-error approach to longwall gate road support is no longer prudent. This paper discusses a design methodology for standing secondary tailgate supports. This design technique requires in-mine measurements of tailgate support loading and convergence to establish a tailgate ground reaction behavior based on support and strata interaction. The methodology uses the performance characteristics generated in the National Institute of Occupational Safety and Health's (NIOSH) Mine Roof Simulator (MRS) to match the stiffness and load characteristics of various supports to the measured ground reaction behavior. It can be used to determine the appropriate application of alternative roof support systems or to design in-mine trials so that a fair and equitable comparison of different support systems can be made. A case study of the methodology at a western Pennsylvania mine site is presented in the paper, including a comparison of four alternative support technologies to the conventional wood and concrete cribbing historically used at this particular mine.

Jan 10, 2000

Electrochemical Behaviour of Massive Chaclopyrite Bioleached Electrodes in Presence of Acidithiobacillus ferrooxidans and Acidithiobacillus caldus In this work, the monitoring of bacterial and chemical dissolution of massive chaclopyrite was evaluated using cyclic voltammetry (CV); the mineral surface was examined using scanning electron microscopy (SEM) and the elements were examined by Energy Dispersive X-ray Analysis (EDAX). The electrolyte employed for the electrochemical tests was the medium used to bioleaching the electrodes (3.0 g/L (NH4)2+SO4, 0.5 g/L K2HPO4, 0.5 g/L MgSO4+7H2O and 0.1 g/L Ca(NO3)2).The results showed differences in voltagramms carried out by Acidithiobacillus ferrooxidans and Acidithiobacillus caldus: In bioleached electrodes tested in the presence of Acidithiobacillus ferrooxidans, the anodic and cathodic current signals were larger than with Acidithiobacillus caldus. The analysis of CV results allowed attributing the different peaks observed in both the direct and reverse potential scanning to the oxidation of chaclopyrite to a secondary copper mineral (bornite, chalcocite and covellite) and its reduction via different non stoichiometric copper sulphides intermediaries. Surface evidences were observed by SEM, and chemical elements evidences were also investigated by EDAX.

Sep 13, 2010

By Anderson Ayres Bittencourt

O monitoramento de sistemas e ativos de automação sempre existiu de forma rudimentar e descentralizada. A análise desses dados tanto quanto sua obtenção é um desafio para as empresas atuais. Foi a partir deste princípio que nosso projeto foi desenvolvido.Este trabalho tem como objetivo demonstrar a solução de Monitoramento online e preditivo implementada na ArcelorMittal Aços Planos da América do Sul, onde desde o início de sua implementação pudemos capturar benefícios operacionais, melhoria dos processos, otimização, eliminação e/ou diminuição de indisponibilidade de plantas, entre diversos outros retornos que serão apresentados.

Oct 30, 2017

Agglomeration for Copper Heap Leaching Agglomeration of ore is a method which can be used to eliminate the migration of fine grained particles throughout a leach heap. Without agglomeration, fine ore particles are able to migration within the heap, clogging flow channels and producing large areas where access of the solution is poor. In order to gain the benefits of agglomeration and improve agglomerate strength even further in copper heap leaching, an economical, acid-resistant binder is needed. However, most binders have been used without any systematic reasoning. A set of novel testing methods were developed, including a soak test, percolation flooded columns, and larger long-term leach columns. The soak test compares the degree of breakdown when agglomerates are subjected to an acidic environment. While the percolation flooded columns and larger long-term leach columns evaluate the flow of leach solution throughout the ore bed. Systematic studies have been completed on a wide range of binders using these novel testing procedures. It was found that for a low grade chalcocite ore, which was rich in silica, from a southwest US mine, polyacrylamides reduced the fines migration the best in the novel soak test. The non-ionic binder, in particular, was found to reduce fines migration as much as 93 per cent. Several of the binders tested were shown to increase the hydraulic conductivities of the agglomerated ore up to 2.5 mm/sec, compared to a hydraulic conductivity of only 0.25 mm/sec when no binder was used. These binders also prevented 'slumping' of the ore, which indicates a decrease in breakdown of the agglomerates. The use of a binder also showed no interference with leaching reactions in long-term leaching experiments.

Sep 13, 2010

By Mark Coleman

Pnuematic Conveying and Process Injection Technologies have been implimented in the metals markets for the last 40 years and have consideribly improved the productivity and the performance of many processes. There have been many steps forward in handling technology and this paper seeks to consider those now offered by Clyde Materials Handling who as an established customer-driven solutions provider, which has turned its attention to supporting the Metals Market. Clyde seek to utilises its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries. With over 30 years experience in the process improvement industry, Clyde Materials Handling has helped their global customer base transform the way in which they operate their processes, which has enabled them to generate sustainable economic benefit and maintain their positions as leaders in their respective markets. Operators within the metals market have developed and deployed pneumatic conveying and pneumatic injection technologies. These environmentally supportive and sustain-able solutions have been used to transport raw materials within operating facilities, from storage to silo, as well as injecting these materials directly into the heart of production processes. Operators, such as Codelco in Chile, Corus Steel in the UK, and many others across the World have seen pneumatic injection solutions transform their process and costs. To inject a consistent, pulseless and accurate flow of material to a copper concentrate bath smelter, or injecting granular or pulverized coal as a coke substitute in to a blast furnace via the Tuyeres helps to increase the operational capacity, availability and productivity and reduce the cost of the operation. This paper will discuss and highlight the ways in which pneumatic conveying and injection technologies, created by Clyde Materials Handling, and applied in partnership with the customer, have helped to improve the operational performance of the production processes of operators across the non-ferrous metals markets with specific reference to applications in the Lead and Zinc Industries. With examples from Zinc Fuming in Australia, Zinc Calcine and Powder Handling in Korea, Precision coal injection to QSL and TSL Furnaces, and metered distribution of Zinc Calcine to Reactors.

Jan 1, 2008

By F. M. Vokes, P. M. Ihlen

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Ore deposition was related to three major stages: continental rifting and separation (Vendian-Late Cambrian), convergence (Late Cambrian-Early Silurian) and collision (Early Silurian-Devonian). The first stage included deposition of volcanogenic massive sulphide Zn-Cu and stratabound or stratiform Fe and Zn-Pb(-Cu) on continental margins, as well as less economic Nb and Fe in carbonatites, U, Mo, Ni and V in Alum Shales and orthomagmatic Cr, Fe-Ti and Ni(-Cu). The numerous volcanogenic massive sulphides formed during convergence included Early Ordovician Cu-Zn, mature-arc Cu, Zn, Pb and Fe-oxide deposits, Besshi-type deposits dominated by Cu or Zn in gabbro-intruded sediments and minor Cu-Ni(-PGE), Cu-Mo and skarn deposits. The collisional stage is represented by epigenetic deposits including sandstone Pb deposits (Pb, Zn, Ba, F and Cu) and minor vein deposits with variable Au, Ag, Pb, Cu, Zn, Fe, As, Sb, W and Mo

Jun 19, 1905

By Mark S. Sanders

This report is a review and synthesis of the published literature dealing with personal equipment items used by low seam coal miners. This report reviews the following items of equipment: headgear, outer garments, respirators, cap lamp, gloves, knee pads, footwear, boots, helmets, ear protection, eye protection. Recommendations for further research and development are included.

Jan 1, 1978

By G. W. Luxbacher

This volume describes the use of the Penn State Mine Ventilation Simulator (PSU/MVS) to model existing mine ventilation systems and, in addition, to evaluate the effect of system modifications. Ventilation survey methods designed to insure computer input data of sufficient accuracy for simulation purposes are covered in comprehensive detail, including quantity and pressure measurement and fan performance testing. The development of input data from ventilation survey results is discussed and illustrated by the use of an actual field survey. Two programs, written in FORTRAN IV with WATFIV, are presented to calculate airway head losses from altimeter pressure measurements. An existing coal mine ventilation system is analyzed and modifications to the system are simulated and evaluated. In addition the application of the PSU/MVS to non-coal mines is briefly discussed. An extensive bibliography on ventilation surveying and simulation is included.

Jan 1, 1977

By P. Taskinen, D. Lindberg, H. Viitala

The formation of copper chlorides in flue dust or deposits in heat recovery boiler of copper smelters or waste-fired boilers may lead to formation of corrosive partially molten deposits on walls and heat exchangers of the boilers. These deposits can contain various other metals, such as alkalis, Fe, Zn, Pb together with oxides and sulfates. In the present study, a thermodynamic model for copper-containing binary and ternary metal chloride systems within multicomponent CuCl-CuCl2-FeCl2-FeCl3- PbCl2-ZnCl2 system has been assessed and optimized based on own experimental phase equilibrium data, as well as literature data. The thermodynamic properties of the liquid phase was modelled using the quasichemical quadruplet model and a thermodynamic database was optimized to predict all available experimental data within the experimental error limits. The thermodynamic database allows for more accurate predictions of potential corrosion-related issues in various heat recovery boilers and waste-fired boilers due to formation of copper chlorides. INTRODUCTION In the copper flash smelting, flue dust can cause severe problems in the gas train, used for separating dust from the SO2-rich off gas, by forming corroding accretions on the walls of the heat recovery boiler. Formation of dust build-ups in the boiler need to be cleaned regularly and potential corrosion damage checked, requiring costly and unscheduled shutdowns of the flash smelting process. Compounds of copper and zinc among other elements having high vapour pressures may volatilize during the smelting of the copper concentrate, forming dust when the process gas cools down. Also, particles of solid or liquid iron oxides originating from the ore get transported with process gas to the heat recovery boiler as a result of entrainment in the flue gas (Miettinen, 2008) The dust deposit build-ups on the boiler walls are formed partly by direct impact of particles and partly by vapour condensation on the boiler walls. The initial deposition takes place by the condensation of vapours that contain zinc, lead, arsenic and other metals having high vapour pressures. Also, low melting point eutectic components of alkali salts such as chlorides and sulphates can act as sticky cohesive particles attaching to the boiler walls. The fine particles landing on the surface of the porous dust deposit layer react in the SO2-rich atmosphere of the boiler to sulphates. The process gas within the boiler contains SO2, O2, SO3, H2O and N2 that diffuse into the porous accretions to form a stagnant gas layer within the dust deposit structure. The composition of this gas layer may differ greatly from the composition of the process gas that is flowing on the surface of the accretion layer. Locally HCl and H2SO4 are formed and even a reducing atmosphere may exist within the dust deposit layer, allowing new reactions to take place. The local micro-atmosphere may enable metal sulphates to be reduced to secondary sulphides and even metallic components. Within the accretion layer, components may be formed that would not be stable in the gas atmosphere inside the boiler (Miettinen, 2008). This may be the mechanism by which for instance chlorides of Cu, Fe and Zn are formed within the deposit layer.

Jan 1, 2019

By Cardm Jeffrey W.

The decay of 222 Rn yields a series of short-lived decay products which become attached to the surface of a plate or wire exposed in a 222Rn-bearing atmosphere. The alpha-activity of two of the decay products, 218Po and 214Po, can be measured by simple counting techniques. This phenomenon may have direct application to uranium exploration. Laboratory studies have shown that: (a) radon decay products can be collected on a wide variety of materials (including various kinds of metals and plastics); (b) activity increases as a function of the surface area of the 'collector; and (c) the collection of the decay products is enhanced by applying a negative charge. The new technique was used in situ to delineate the anomaly above the South March uranium-copper occurrence. A related technique was developed to measure radium in soil samples. The results of both studies compared favourably with those obtained from conventional methods.

Jan 1, 1979

Lignite deposits of Central Otago Miocene Dunstan Formation accumulated on a broad alluvial plain and on deltas that flanked a large freshwater lake. The regional subsurface distribution and configuration of the lignite-bearing strata are identified within the context of depositional systems and placed into a genetically defined stratigraphic framework. The stratigraphic and depositional models constructed, should form an integral part of the geological assessment process to guide future regional or mine based lignite drilling programmes. Further testing and evaluation of the commercialy important lignite deposits in the Blackstone and Roxburgh Coalfields are required to adequately characterise the lignites and their geological setting, particularly to select methods of mining and wise uses of the lignite.

Jan 1, 1992

By J. R. Thoenen

This circular is part 5 of the third paper (entitled "Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes; part 2, power scrapers, slackline cable-way excavators, and hydraulic monitors; part 3, hydraulic, clamshell, ladder, and dipper dredges; and part 4, haulage systems in general, with particular reference to locomotive and car, hoist and car, and remote-control systems. This circular discusses the use of motor trucks, conveyor belts, pumps end pipe lines, barges and towboats, and aerial trams. MOTOR-TRUCK HAULAGE During recent years motor trucks have gained considerable ground as a successful competitor of locomotive haulage for quarries and gravel pits. Often where trucks have displaced locomotives and cars the operators readily admit an increase in both labor and total haulage operating costs but point to some other advantage as offsetting the extra expense. In other instances haulage costs have beep reduced by the use of trucks. In still others operators, having replaced locomotive haul with trucks, have again returned to the earlier method. Obviously gasoline-driven motor trucks cannot successfully compete with other types of haulage under all conditions. The apparent' growth in the number of advocates of truck haulage, however, indicates that it has passed the experimental stage and become a permanent competitor to other tyres.

Jan 1, 1936

Mineral formations, accumulated during technogenic activities greatly influence an economic and ecological situation in the Kola North. On the one hand, the dumps from extraction of mineral resources, tailing ponds of beneficating plants, ash dumps, wastes of metallurgical and mechanical engineering productions destroy the regionÆs environment and require taking certain measures and costs to bury or protect from weathering, oxidation, etc. On the other hand, technogenic mineral formations contain a lot of valuable scarce components. The amount of solid wastes increases annually, causing damage to ecology and economy. Researches conducted in recent years showed a possibility and economic expediency of comprehensive processing of wastes from different enterprises in Murmansk region and their use for production of new competitive commodity output, possessing high consumer properties. Thus, involving mineral wastes from Khibiny apatite deposits into hydrometallurgical industrial processing provides the basis for setting up a large beneficating-metallurgical complex. In this case ores and wastes from other deposits on the Kola Peninsula, containing titanium, rare, rare-earth and other valuable elements, may be involved into processing. Establishing such a complex will allow to organise a deep processing of natural resources, utilise some production wastes, improve ecological security and supply production with competitive output. Expanding the complex implies not only involving new mineral raw material into processing, but mainly deepening raw material processing, maximum utilisation of local natural resources and obtaining a wider variety of prime products.

Jan 1, 2002

By J. K. Whyatt, B. G. White

A comprehensive survey of mine seismicity and rock bursting during development of two sublevels at the Lucky Friday Mine, Mullan, ID, USA, was conducted to better define rock failure mechanisms and sources of ground control hazards. Survey data included rock burst damage reports, seismic event locations and magnitudes and, for the most energetic events, first-motion information. Several subsets of this database, including large seismic events, rock bursts, and microseismic activity near the face, were analyzed. Elements of the large-event and rock burst data sets were nearly independent. That is, there was no relationship between the risk posed by a seismic event and its energy, although such a relationship is well established for the mine as a whole. All data sets showed that certain geologic features appear to control the spatial distribution of events and the spatial distribution of rock burst risk. The data also suggest that, within the scope of this study. the greatest risk of injury occurs when a pocket of heightened rock burst risk is first encountered and that this risk is controlled when miners adapt their practices to these conditions. Recognition of the role of particular geologic features in the spatial distribution of rock burst hazards provides an opportunity for anticipating, rather than only reacting to, a changing level of rock burst hazard- However, much work will he required to make good on this promise.

The Purification of Low-Grade Quartz Ore by Flotation and its Mechanism

Sep 13, 2010

By Y Zhuang, S La Brooy

The selection of the optimum process route for a new project has traditionally consisted of investigating existing options and ranking them in terms of cost, technical risk and environmental acceptability. With the current focus on sustainable development other factors now need to be considered. Life Cycle Assessment (LCA) of the process options can be used to extend the assessment in terms of their potential for earning renewable energy credits and in judging their ability to achieve greenhouse gas emission reductions. A rigorous life cycle assessment is demanding in terms of setting the baseline for comparisons and evaluating the elements that make up the emission profiles of the process options. However, a simplified LCA can provide a useful tool for comparing different process options. This approach can be combined with traditional assessment criteria to rank the options available to the project. GRD Minproc has been intimately involved in executing LCA calculations for different municipal waste treatment options. This paper applies a similar LCA methodology to investigate the greenhouse gas implications for different options for copper processing. The process options considered are:concentrator û sale of concentrate to smelter, concentrator û on-site mini smelter, and concentrator û leach SX/EW. The paper then goes on to consider the operating cost implications that could arise with the introduction of carbon taxes or carbon credits and how these might impact on the future choice of flowsheet.

Jan 1, 2002

By Parker A. J, Giles D. E

Solutions of copper(II) sulphate in acidified aqueous acetonitrile leach copper from copper-lead matte derived from the drossing of lead with sulphur to produce solutions of copper(I) sulphate. The reactivity of the matte constituents towards copper(II) sulphate is Cu2S> PbS > CuS > > Pb. According to the leach conditions, part or ,all of the copper may be leached 'leaving a residue of CuS/PbS, or S/CuS/PbS04, or S/PbS04, to be recycled to the lead smelter. Complete extraction of the copper requires leaching with oxygen which occurs under mild conditions in the presence of acetonitrile and sulphuric acid in water. Copper is selectively recovered as a pure product by electrochemical or thermal disproportionation of copper(I) sulphate solutions. A notional process is proposed.

Jan 1, 1979

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United states and publishes economic data on the peat industry, based upon reports submitted by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all commercial producers, although a few small companies may not have been canvassed as the industry has many small operations that operate intermittently. Output of the various companies listed ranged from a few tons to more than 50,000 tons. Peat is included in the Bureau's annual surveys of the mineral industries because peat is classified as a mineral fuel. Although none is used for fuel in the United States, peat is a potential source of energy and ranks as one of our large mineral resources. The domestic peat industry sells peat, chiefly, for use as a soil amendment for general soil-improvement purposes. During the past decade the industry has expanded rapidly with operations increasing from 45 in 1947-494/ to 115 in 1960. Output during this period has more than tripled, increasing from 131,782 short tons to 470,889 short tons.

Jan 1, 1961

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rim. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988