Search Documents

By M. Makarchian

Existing buildings sometimes experience excessive settlement under their design loads, or due to increased foundation loading, if a change of building use is required. One of the oldest and widely numerical study has been carried out of a simple idealised problem of an underpinned rigid circular foundation to better understand the behaviour of pile used for underpinning and load transfer mechanism from an existing foundation to the underpinning piles. The finite element method has been used for this analysis, with the soil treated as a two-phase elasto-plastic material. It is found that the effect of the length of the pile becomes more significant as pile length increases. As would be expected, the earlier the pile is installed, the less is the final settlement.

Jan 1, 1996

By John F. Gamble

Paper 1?South African experience with asbestos-related environmental mesothelioma: Is fiber type important? Neil White, Gill Nelson, Jill Murray The purpose of this review was to illustrate the importance of the type of asbestos in environmental mesothelioma. South Africa is a logical place to assess fiber type. The three major types of asbestos (crocidolite, amosite and chrysotile) were mined (all asbestos mining stopped in 2002) in South Africa. The association between asbestos and mesothelioma was discovered in South Africa. The occupational literature indicates high mesotheliomagenic potential for crocidolite, less for amosite and less still for chrysotile. Since South Africa has been a major source of crocidolite, relatively high rates of mesothelioma in the mining population is not surprising. High rates of mesothelioma due to environmental exposure is surprising, except perhaps when the authors? point out potential sources for community exposures (e.g., mine tailings used for road surfacing, golf courses, brick and plaster making; insulation in residential ceilings; children playing on fiber-rich waste rock). The authors? reviewed four studies reporting on mesothelioma cases and their sources of exposure and fiber type. Overall 23% of the known cases were attributed to the environmental (not occupational) exposure and about 90% were due to crocidolite asbestos. The proportion of environmental mesothelioma is considerably higher than in Western Australia where crocidolite is also mined. There the overall rate of environmental mesothelioma is about 6% (and less than 1% from residence in a crocidolite mining area).

Jan 1, 2007

Neutralization with lime is a simple, cheap, and effective means of treating acid raffinates from uranium processing to' raise the pH, reduce the concentrations of dissolved salts (including heavy metal impurities), and remove amine by adsorption. Two-stage neutralization, using limestone in the first stage at approximately pH 4 and lime in the second, lIlay be advantageous.Lime neutralization of mffinates in the pH range 7 to 8· 5 generally reduced the radium ·concentration to 10 to 200 pCi 1-1, but ·there was considerable scatter in the experimental data. The radium concentration was further reduced to less than 3 pCi 1-1 by co-precipitation of barium (radium) sulphate with 10 mg Ba (as barium chloride) per litre of raffinate. Adsorption of radium on barytes was -also effective in reducing the radium concentration in neutralized raffinate to less than 3 pCi 1-1.The radium concentration of pit water was readily reduced to less than 3 pCi 1-1 when pit water containing 0·01 M sulphate as ammonium, calcium, or sodium sulphate was treated with 20 mg Ba per litre of pit water.Adsorption on barytes was also effective in removing radium from pit water containing 0·03 M sulphate.

Jan 1, 1975

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

By Robert M. Funk, James E. Lawver

The development of a laboratory and pilot-scale high-tension electrostatic flowsheet for the production of iron-ore super concentrates having silica contents in the range of 0.1% is presented, A variety of hematite and magnetite ores were tested with this flowsheet, and the pertinent metallurgical data are given. The applications and limitations of this process are brought out in terms of both practical and theoretical considerations. There have been many new developments in the past few years that have required mineral beneficiation engineers to consider new techniques for iron-ore concentration. Developments in iron powder metallurgy, and particularly the making of sheet metal directly from high-purity iron-ore concentrates, and the concept of using metallized pellets as a substitute for scrap in electric-furnace steelmaking have created demands for what is commonly referred to as iron-ore superconcen-trates. In most cases, specifications for superconcentrates are that they contain less than 0.1% total gangue, with some applications requiring less than 0.05% gangue. To produce these concentrates, new and modified processes are being developed, and the three methods receiving attention as the primary concentrating methods are: 1) Magnetic separation in which dry rotor-type equipment is used for magnetite and the high-intensity magnets are used for hematite. 2) Amine flotation. 3) "High-tension" electrostatic separation (or, elec-trodynamic concentration). This paper examines the high-tension electrostatic process in terms of its limitations and abilities for the production of iron-ore superconcentrates. A technically effective and simple flowsheet was developed through laboratory and 5 and 100-ton pilot-plant studies for the production of concentrates containing from 0.02 to 0.20% SiO, with iron recoveries between 85 and 90%. The process is also shown to be economically feasible. Laboratory Test Program Separation Characteristics: The suitability of the electrostatic high-tension method for iron-ore supercon-centration stems from the fundamental mechanism governing the process, i.e., particles are separated on the basis of differences in electrical conductivities. This conductivity is a characteristic property of minerals, and if the difference between the conductivities of two min- erals is great enough, then their separation can be performed by a high-tension machine. As shown in Figs. 1 and 2, the critical factor is the time necessary for the particle charge density, which is established by a corona discharge field, to decay to a level such that the centrifugal force acting on the particle exceeds its electrostatic, or image, force. At this point, the particle can leave the rotor at some trajectory and fall into an appropriate product receptacle. This decay time is directly proportional to electrical conductivity, and the process variables, such as feed rate, rotor speed, electrode configuration, and rotor composition, are selected to optimize the ability of the separator to resolve different conductivities. Table 1 lists the measured conductivities for some of the iron and gangue minerals used in developing the flowsheet. These results were obtained by using the conductivity cell described by Lawver and Wright.' The discharge curve of most minerals that lend themselves to super concentration by high-tension is so fast that the

Jan 1, 1971

By McKinnon R. L

Laboratory and field work on the use of wetting agents for suppression of colliery dust is described. Although the results were inconclusive they were not discouraging and further investigation is required. The use of certain wetting agents may constitute a healthhazard.INTRODUCTIONCoal dust presents explosion and health hazards to the coal mining industry. The problem of dust suppression is particularly acute where water alone is unsatisfactory for this purpose. The addition of a surface active agent (wetting agent) to the water should enable the dust particles to be more easily wetted and thus more easily prevented from entering and spreading through the mine atmosphere.Investigations into this effect carried out at The University of Sydney mainly under research grants from The Joint Coal Board (Dawson and Hargraves, 1955; Charlton and Curnow, 1957) are summarized, and information on the possible harmful effects of certain wetting agents is given.Twelve local manufacturers and five importers supplied 52 wetting agents in liquid, solid, powder, and paste form.The active material content varied from approximately 10 per cent to 100 per cent and the cost per pound from 8d. to 14/3.LABORATORY TESTINGPossible test methodsThree methods of laboratory testing were considered.1. The standard method for comparing wetting agents is the Draves test, used in the textile industry on cotton...

Jan 1, 1961

By C. Legote

"This paper investigates the conditions leading to the indefinite termination of production in four critical primary panels at an underground coal mining operation, the observed shortcomings in the mining approach, and the proposed strategy to mine through the affected panels. Initial assessment of the abandoned panel conditions indicated time-dependent strata failure,(i.e. bolted roof failure overrunning intersections), which occurred from mere minutes to up to four weeks post-production, with and without prior warning of failure. This prompted the constant re-supporting of back areas, which raised safety and productivity concerns. Investigation of the initial mining conditions revealed that the failures were due to a critical combination of factors, the chief of which was isolated horizontal stress. Other factors that were initially overlooked by the mine (i.e. influence of hydraulic stress, misinterpretation of borehole data), resulted in the conditions being described as abnormal. Remedial actions were determined, and in so doing, a new strategic approach was formulated to thoroughly address all failure concerns. The four panels were explicitly planned to serve as the main intake and return airways for the recently commissioned secondary ventilation shaft, as well as providing access to millions of tons in proven coal reserves. It is thus imperative to mine the panels. A feasibility study showed that the proposed strategy set for implementation would be financially viable. Paper written as project work carried out in partial fulfilment for BEng(Mining Engineering) degree"

Jan 1, 2015

CONTENTSIntroductionNorthern ExplorationDrive ConceptionGeneralDriving CrewDrive Cross Section and Track DetailsVentilation by Electrically Driven FanTemperatures and HumidityFan PerformanceRock Drill Carriage and Rock DrillsStandard Drilling RoundElectric Firing from Power MainsExplosives and DetonatorsCharging and FiringMechanical Loading and Electric HaulageOperating CycleStatisticalEquipmentAcknowledgementINTRODUCTION.The driving project described in :this paper is one of greater magnitude than usual for the Broken Hill field, and in the execution of the work a departure was made from long-established local practice by the introduction of mechanisation. The primary object of the drive is to provide sites for gaining information regarding the behaviour of the ore-bodies well beyond the limits of the present exposures.Due to thermal conditions, the major portion of the work was done on a six-hour shift basis, in contrast to the normal one of seven hours, with a five-day week.

Jan 1, 1946

By A. Moergeli

The Swiss are building the world’s longest tunnel, the 57-Kilometer (35-mile) long Gotthard Base Tunnel. Lot 252, Tunnel Amsteg: Two Hard Rock Tunnel Boring Machines (TBM) crossed hydro-thermally decomposed granite. While the East TBM advanced slowly but steadily, the West one got stuck for five months and had to be recovered by special means and methods. Both TBMs have finished their more than 11-Kilometer (7 miles) long drives successfully. Lot 360, Tunnel Sedrun: For the first time in tunneling, roadway support machines are used through most challenging, squeezing geology. They constantly advance in full face mode for about one Tunnelmeter/24 hours.

Jan 1, 2007

By Frank Rausche

Since the early 1980s, when the Road Construction Authority of Victoria authorized the dynamic proof testing of roughly 100 drilled shafts of 1.5 m diameter and typically 60 m length in Melbourne Australia, dynamic load testing has been applied worldwide for quality control of drilled shafts. Today, test capacities of 4000 tons or more are not unusual. On numerous occasions the authors have been involved in similar tests in the United States and test engineers from other countries have reported on experiences in many different countries. Without doubt, generating high test loads is most economically accomplished by dynamic load testing and this method is particularly well suited for testing piles founded in rock because of the rocks low energy dissipation. However, deep foundation professionals have on occasion expressed reservations about subjecting a drilled shaft to impact loadings fearing, for example, a degradation of the shaft ? rock interface properties or potential error sources due to uncertain concrete properties or shaft geometry. This paper will present numerous case studies, demonstrating the performance of rock socketed drilled shafts under dynamic loads. It will discuss the mechanics of the dynamic tests and the method of data interpretation, addressing the concerns stated above and investigating the limitations of the test method. The paper will formulate a set of recommendations for the design and execution of these tests.

Jan 1, 2006

By M Pizey, M Kingsbury

Since 1950 Stockton Open Cast Mine has excavated over 60 million tonnes of Brunner Coal Measures overburden sandstones and mudstones. The current operator, Solid Energy New Zealand, recognises that acidic drainage from this overburden and from historic underground mines has led to depressed pH levels and elevated levels of metals in streams draining the Stockton Plateau. These streams report to the Ngakawau River. To quantify the effects of mine site acid drainage remediation/mitigation on the lower Ngakawau River water quality, a catchment hydrogeochemical model has been field calibrated and ecotoxicology tests have been undertaken. The hydrogeochemical model indicates that pre-mining and present pH values in the lower Ngakawau River are similar but present aluminium and iron concentrations are elevated. Ecotoxicology tests have semi-quantified the critical metal concentrations and interim water quality targets to achieve ecological recovery are presented. Analyses of long-term total suspended solids (TSS) and turbidity monitoring in the lower Ngakawau River and St Patrick's Stream indicate that TSS of 120 mg/L and turbidity of 20 NTU are exceeded for <20% per cent of the time. Hence, specific criteria to protect migratory native fish from turbid water are currently met in the Ngakawau River and St Patrick's Stream.

Jan 1, 2003

By Met B. E

During the operation of the Parkes process of desilverising, and in the earlier days of the continuous process, gold and silver were removed separately from softened lead bullion. Gold was removed in the Parkes process by a selective zincing, and -in the continuous process by treatment with zinc in a special de-golding kettle, in each case a crust being obtained carrying the gold and a small portion of the silver. Actually the process could have been more correctly termed a de-copperising process, on accountof the relatively large amount of this metal present, and its affinity for zinc, which caused it to enter the crusts produced.The crust was treated in reverberatory furnaces, where the bulk of the copper and zinc was removed in by-products, and the resulting "gold bullion" cupelled to give adore bullion containing approximately 2,000 ounces gold per ton.For the purpose of parting this dore, a small Balbach-Thum plant of 11 cells was used, and once each six months a short campaign was conducted on the accumulated metal.With the development of the process of de-copperising smelter bullion by means of sulphur, when a bullion averaging about .004% copper was constantly available for refining, the need for a separate de-golding process disappeared.The de-golding kettle of the Continuous Process...

Jan 1, 1937

By Edmund S. Leaver, R. S. Dean, T. L. Joseph

The metallurgy of manganese has developed along the lines of iron metal¬ lurgy. Enough high-grade ore has Been available so that by reduction with carbon it could be turned into an iron-ma.nga.nese alloy and a slag containing some 9 to 15 percent manganese. More siliceous ores have been smelted in the blast furnace to form iron-silicon-manganese alloys called spiegel. When lower-grade ores came in for serious consideration, which lias only been since l°l4, two types of processes received the most consideration — hydrometallurgical processes to produce a concentrate which could be smelted like the higher-grade ore and processes involving concentration of the manga¬ nese from manganiferous iron ores by preferential reduction of the iron (184)1. Special chapters in this bulletin are devoted to the production of ferro¬ manganese from ore, the hydrometallurgy cf manganese, and the Bureau of Mines modification of the preferential reduction process. Other methods of producing manganese alloys from low-grade or refractory ores have been suggested and may find future application. Manganese has a very high affinity for sulphur and is particularly adaptable to concentration by matte smelting. According to Betts (26), manganese silicate may be smelted with pyrite to give manganese sulphide and iron silicate. This method would be applicable to concentration of either the silicate or carbonate ores. The sulphide, once obtained, could be roasted to oxide and reduced in the usual way. Another possibility for the production of manganese from silicate ores involves their reduction by silicon or manganese silicides. Swedish Patent 52290, February 25, 1925. covers the reduction of a slag rich in manganese by silicon-manganese alloy containing more than 10 percent silicon, Joseph H. Brennan (38.) describes the concentration of manganese iron ores by partial reduction with silicon. Beckett (7,4,19) describes the reduction of manganese dioxide with a manganese silicide for the production of standard ferromanganese. Beckett gives as a typical alloy, manganese 64.4, silicon 24.6, and as a typi¬ cal ore, 5S.5O manganese as MnO^. The product of the reaction between these two is 80.11 percent manganese and 1.22 percent silicon.

May 1, 1934

By Dennis W. Boehm

The building boom of the late 1970's and early 1980's has all but used up most of the better sites across the more populated metropolitan areas of the United States. This means that current buildings and other types of structures are being founded on more marginal sites. The use of marginal sites has placed ever-increasing quality control on the installation of the deep foundation systems utilized for these sites. Several remedial techniques are available for the repair of the deep foundation systems. These include minipiles, compaction grouting and jet grouting. Eight case histories are cited where these methods have been utilized to repair deep foundations.

Jan 1, 1999

By A. Dave Mackintosh

In 2001, at the CIM AGM in Quebec, a paper discussing poor ground conditions in a newly opened area at Agrium?s Vanscoy Potash Operation?s, suggested load transfer around old workings as a possible reason for the early room failure. High closure rates are expected in deeper regions however the rapid failure of walls immediately behind the face resulted in protective guards being mounted on and behind the borer. The high closure and early rib failure continued well past any reasonable distance to be explained by load transfer around old workings and investigations continued into possible reasons other than simply depth. Detailed investigations into the mineralogy and crystal fabric of the ore zone provided one possibility, which combined with a changed borer cutting profile are now believed to have contributed greatly to the poor conditions.

Apr 1, 2005

The results of self potential geophysical surveys conducted over base metal prospects near Orange, Goulburn, and Wellington, N.S.W., indicate that this rapid and inexpensive exploration procedure merits wider application within eastern New South Wales, and in similar environments elsewhere.

Jan 1, 1973

By J. D. Steenkamp

Keywords: Thermal, conductivity, diffusivity, expansion, history, density, specific heat capacity, industrial rich high-carbon manganese slag The thermal conductivity of slag is an important parameter in the design of furnace-containment systems based on freeze-lining technology. Literature indicates that the crystal content of a slag has a significant influence on its thermal conductivity. Industrial, rich, manganese-bearing slag was cooled at different rates to create samples with different microstructures. The coefficients of thermal conductivity of these samples were measured in a nitrogen atmosphere from room temperature to 990°C at 100°C intervals. The laser-flash measurement technique was used for this purpose. Follow-up investigations included XRF and XRD and modelling in FACTSage.

Jan 1, 2011

By Gordon King

The site of the First Quality Tissue plant is located on a previous paper production facility in Lock Haven, Pennsylvania. The new development, which included the construction of a tissue machine building, baled building, converting building, various storage buildings and an electrical switchgear building, required the use of deep foundation systems to transfer loads below compressible fill and alluvial soils. Loading details provided by Jacobs Engineering, the project structural engineer, detailed braced steel frame buildings with typical column loads ranging from 75 to 150 kips and slab live loads of 250 to 300 psf. As an exception to this, however, the tissue machine and stock preparation building, which had a roof height ranging up to 85 feet, had column loads ranging up to 800 kips in addition to high dynamic loads. The First Tissue plant is located in a river valley in the hills of Western Pennsylvania. To evaluate the proposed site conditions and to formulate recommendations for the structure foundations, a geotechnical study was performed by the owner. Approximately 30 borings were advanced to bedrock, with wire-line coring performed in the tissue machine building. The borings disclosed a soil profile comprising of the following:

Jan 1, 2004

By S. J. Jung

A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.

Jan 1, 1989

The literature pertaining to the electrochemical reaction at the anode during electrolytic reduction of alumina by the Hall-Heroult process is not in universal llgreement about the gaseous product. The possibility of electrochemical formation of CO at the anode was examined using existing data. Although the thermochemistry favours co-evolution of CO and CO2 with CO as the major product, the mechanism of the reaction shows this is unlikely. Since the origin of CO can be more logically explained by non-electrochemical mechanisims, it is concluded that CO2 is the only product from the electrolytic reaction at all current densities.

Jan 1, 1967