Search Documents

By Parker A. J, Muir D. M

Solutions of acetonitrile in water dissolve water soluble copper(I) chloride. Removal of volatile acetonitrile from the resulting solutions, by distillation with low grade steam, precipitates pure copper(I) chloride. This is used to purify a crude copper chloride sublimate from the chlorination of nickel matte but is applicable to other sources of copper(I) chloride. The pure product can be converted to pure copper(I) oxide, copper(II) oxychloride or pure copper metal directly.

Jan 1, 1980

By Horst Peter Wölfel

The goal of biodynamic models is to simulate the vibration behaviour of the human body. In combination with experimental studies biodynamical models can be a powerful tool for the analysis of the effects of vibration exposure on health [1] and comfort. This paper gives an overview of the state of the art of biodynamic whole-body vibration models of humans, addressing both numerical models and hardware dummies. Method Two approaches are distinguished, the phenomenological and the anatomical, as illustrated in Figure 1. [ ] Phenomenological models aim to reproduce the vibration behaviour of humans with respect to particular physical quantities, chiefly the driving-point impedance at the interface to the seat, and partly with respect to other transfer functions. Discrete systems of masses, springs, and dampers with several degrees of freedom whose topology and parameters are determined by structure- and parameter identification methods are used in the sense that the functions derived from measurements are reproduced as well as possible. This paper provides an evaluation of this methodology and defines its range of application as well as its limits.

Jan 6, 2006

By T DePetris, B B. Beamish

There has been a gradual increase in the volume of internationally traded thermal and coking coal, with emphasis on blending of coals rather than single coal usage. New Zealand can take advantage of this situation, especially with its low ash and sulphur content coals. However, there is a need to clarify the thermal and coking behaviour of these coals as they relate to other market players, to benefit both the consumer and supplier. The high volatile matter contents of New Zealand coking coals are due to their high vitrinite content, which causes them to demonstrate stronger coking properties over a wider rank range than Gondwana coals. These same high vitrinite levels appear to correspond with lower initial softening temperatures than for Gondwana coals of similar rank. Preliminary results using thermogravimetric analysis also suggest that New Zealand high volatile bituminous coals can be used to substitute for higher rank Gondwana coals in combustion processes.

Jan 1, 1994

By F. Seitz

STAFF: Editor, Gerhard Derge Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Managing Editor, James J. Burke THE METALLURGICAL SOCIETY: John Chipman, President; W. R. Hibbard, Jr., Post-President; C. C. Long, Vice-President; T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. Maddin, Chairman; Dennis Carney, J. C. Fulton, J. H. Hollomon, T. B. King, C. C. Long, W. 0. Philbrook, J. D. Sullivan, David Swan, and F.L. Vogel. Review and selection of manuscripts is under the supervisian of the following Publications Committees: Extractive Metallurgy D ivis ion: T. 0. King, Chairman; S. J. Dick inson, R. P. Hermsdorf, R. Schuhmann, Jr., and H. H. Kel logg. Institute of Metals Division: F. L. Vogel, Choirmon; R. L. Smith, Vice Chairman; R.W. Balluffi, J. H. Bachtold, A Servi, C.D.Graham, Jr., C. G. Goetzel, F. E. Joumot, Jr., G. E. Pellissier, Paul Gordon, Jock Washburn, Harold Margol in, A. U. Seybolt, I. R. Kromer, R. A. Meussner, R. W. Guard, M. Harmon, J. N. Hobstetter, Dean Starr, P. Shewmon, R. Gordon, J. 0. Betterton, and E. Morgan. Iron and Steel Division: W. 0. Philbrook, Chairman; F. C. Langenberg, C. W. Sherman, J. Wagstaff, and E. J. Whittenberger. Published bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for non-AIME members in United States and North, South, and Central America; $25, foreign; $5 for AlME members. Single copies, $4.00, single copies foreign, $5.00. The AlME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1959 by the Americon Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York ... Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts . . .Second class postage paid at New York, N. Y. , ond Ann Arbor, Mich. Volume 215, Number 3

Jan 1, 1960

By Charles F. Seemann

It is with considerable trepidation that I set out to defend "litigation" to Design Professionals (DPs), as a better method of resolving disputes than arbitration, in the light of my personal feeling that an increasing amount of America's productive process is being squandered in litigation. Newer methods of dispute resolution, particularly arbitration, are fashionable, and opponents of these schemes risk being viewed as cynical or self-serving. My quandary is heightened since for some smaller disputes, arbitration seems clearly the better choice. I must concede, for example, that when the cost of dispute resolution--i.e., the cost of the process (such as arbitrators fees, attorneys fees, etc.), plus the cost impact of the non-productivity of involved employees--approximates the amount of the dispute, controlling that cost may be as important as a correct resolution. This principle is particularly true for small disputes arising during the progress of a project; it is probably more cost-effective for all parties to resolve their disputes quickly than permitting the dispute to drag out.

Jan 1, 1988

By Andrea McGlynn

Iron Ore Company of Canada, Labrador City 2011?Canada's largest iron ore producer, leading global supplier of iron ore pellets and concentrates ?Rio Tinto (58.7%), Mitsubishi Corporation (26.2%), Labrador Iron Ore Royalty Income Fund (15.1%)

May 1, 2011

In a previous paper the writer dealt -with the jasper bar formations and their relationship to the structural geology of older pre-Cambrian rocks in the goldfields districts of Western Australia (24). He has pointed out in this ahd other papers that jasper bars, or banded iron formations, banded hematite or ,magnetite quartzites, jaspilites and related banded ferruginous or non-ferruginous cherts, occur in abundan'ce in the Older Greenstone Series of Western Australia (22), (24), (26). They are considered to represent special forms of banded ferruginous sediments, and are usually fpund in the field interbedded with more or less metamorphosed pasaltic 01' andesitic lavas and tuffs, now amphibolites, together with occasional thin bands of normal pelitic sediments, which go to make up a large proportion of the Older Greenstones in thfs State (26).Great thicknesses of fiat-bedded ]:landed ferruginous cherts are also found associated with cherty' carbonate rocks; quartzites, shales and thin-bedded dolomite whicIi constit'ute the Nullagine (Pl'oterozoic) system in the northwest of Western Australia. In the Hamersley Range district these banded ferruginous chert beds are the hosts of important deposits of blue amphibole asbestos.In the paper mentioned above brief reference was> made to the importance, of geological structure in relation to economic geology, particularly in the goldfields regions of Western Australia, and it was shown that jasper bars may have an important role in the study of 'the structural geology of many of these regions. Of possibly more immediate economic importance is the part that these rocks play, both directly and indirectly, as host rocks for mineral deposits-the chief of Which are gold, iron ores, blue asbestos, and manganese ores. The blue asbestos bearing banded iron formations mentioned above are confined to the younger pre-Cambrian Nullagine formations. They have been described in detail elsewhere (23). In this paper it is proposed to discuss the economic geology of the jasper bars found in the older pre-Cambrian series.The jasper 'bars have in themselves little or no intrinsic value except perhaps some of the more highly coloured and banded varieties which may be utilised for ornamental and decorative purposes. Probably the best known of such varieties is the so-called "marble bar;" a belt of, strikingly coloured banded chert occurring just south and west of the famous town of that name (see Fig. 1t). This consists of a hard, very fine, even-grained rock with alternate individual stripes varying from the thickness of a sheet of paper up to an inch or more in width, and ranging in colour from clear white to yellow, from various shades of pink to brilliant...

Jan 1, 1943

The Porgera Joint Venture commenced production during September 1990. A small tonnage underground mine extracts high grade gold ore using small scale stopes. Conventional drill and blast methods are used for development and production mining. Ground support is effected with Splitset anchors, grouted rebar bolts and grouted cable bolts. Splitsets and grouted rebar can be installed by mechanised means. Vertical crater retreat, slot and massfire, and modified VCR stoping tech- niques are used at Porgera. Stopes are backfilled with a relatively strong cemented rockf ill. Future stope sequences require recovery of pillars beside and under filled stopes.

Jan 1, 1991

By D. S. Dihalu

A generalization of Gy?s model for the fundamental sampling error introduced the new ?parameter for the dependent selection of particles?, denoted as Cij. This allows for modeling deviations from the ideal situation where the selection of a pair of particles is composed of two independent selections. The generalized model potentially leads to more accurate variance estimates in the case of clustering of particles, differences in densities or sizes of the particles or repulsive inter-particle forces. A straightforward and practically applicable method is needed for the determination of this parameter for miscellaneous mixtures in industrial settings. In this contribution, the feasibility of using digital image analysis to determine this parameter Cij, will be demonstrated. Line transect sampling of a digital image was used to construct a transition probability matrix. A new algorithm to derive quantitative estimates for Cij will be presented and discussed. The applicability was verified by a photograph of zirconium silicate particles of sizes typical for industries dealing with pharmaceutical, food/feed, and environmental applications. Conditions affecting the practical applicability are identified and potential pitfalls will be discussed, including e.g. how a potential unrepresentative surface can affect the quality of the estimate of Cij.

Jan 1, 2010

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2010

A new test coke oven of 7 cu. ft. capacity is described. The oven was designed to simulate conditions in a central section of a battery oven and a special feature is the achievement of unidirectional heating from theflues on either side of the charge.The method of charging permits close control of charge conditions such as bulk density and moisture content.These conditions, as well as coking conditions (e.g. flue temperatures and coking time) must be varied to simulate conditions in different batteries. The effects of several variables on coke quality are discussed.Using test oven conditions corresponding to those of Newcastle steelworks batteries, good agreement was obtained between strength indices of test oven and battery cokes. For 17 tests, the average ASTM stability and hardness indices for the test oven coke were 38· 5 per cent and 69·7 per cent, while those for the battery coke were 37· 4 per cent and 67·6 per cent.Observed relationships between coke yield and productivity, and volatile matter and charge moisture are given.The use of a test oven to classify test coals into prime-, medium-, poor-, and non-coking coals is discussed.This may be achieved by observing the effects of the test coal in blends with other coals. The results of a series of blending tests are presented.The dangers of attempting to predict coke quality from a single coal property are pointed out, since this can be done only for very restricted ranges of coals.A diagram is given showing the established trends in the effects of blending various types of Australian coals on coke strength.

Jan 1, 1970

A process was developed, on a laboratory scale, for the removal of iron oxides from Weipa pisolitic bauxite. The technique involves the chemical reduction ofthe iron oxides by carbon, followed by selective removal of the iron species by acid leaching or chlorination.To remove more than 90 per cent of the iron it is necessary to reduce the iron oxides substantially to iron metal by heating the bauxite, pre-calcined at 650-800°C, with reactive carbon at 1040-1100°C. Reduction proceeds via the intermediate formation of hercynite (FeO.Al2O3) and difficulties have been encountered in reducing hercynite formed under less favourable reduction conditions.Following reduction, efficient selective removal of iron species is readily effected by acid leaching using dilute hydrochloric acid at 100°C, or chlorination at 500-750°C using Cl2, Cl2/N2, or Cl2/N2/CO mixtures.After removal of unreacted carbon, the final products contain 0·5-1.0 per cent Fe203 and 87-92 per cent Al203.

Jan 1, 1971

Building the Unified Comminution Model The Unified Comminution Model (UCM) was formulated with the vision of bringing all comminution models onto a common base. The structure of the model relies on knowledge of the mechanical environment in the comminution devices to predict the modes and rates of collision in a device. A detailed understanding of the breakage modes and an ability to correctly test these modes for the ores in question is then required to feed into the UCM. A model structure has been developed that has the capability of dealing with multiple modes of breakage, such as low energy impact surface damage, chipping, sliding abrasion, cumulative impact body breakage and the transition of rock between modes. A critical review is presented on the shortcomings and limitations of utilising the discrete element method (DEM) to provide the mechanical environments. The assumptions and applicability of utilising DEM in milling models are presented and proposed routes to building a realistic mechanistic model are proposed. Based on this more realistic measures of collision energy have been derived from the DEM simulations, which better mimic the real breakage tests. Generic forms of the collision energy distributions have been observed and developed into functional forms for use in the simulation environment. The method of application of this model to a pilot SAG mill is presented.

Sep 13, 2010

By John L. White

Vibratory driver/extractors do more than drive and extract sheet piles. I would say more than sixty percent (60%) of the time, vibratory pile driver/extractors are engaged in work that has nothing to do with sheet piles. This is the main reason I refer to this tool as a "driver/extractor", and omit the word "pile". I have spent the last twenty years applying the technology of the vibratory driver/ extractor to all areas of foundation construction. As you will see, the only limits are humankind's ingenuity.

Jan 1, 1997

By J. M. Dean, R. L. Grayson, R. C. Althouse, M. J. Klishis, G. L. Winn

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Feb 24, 1997

By Gerald V. Gibbs

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 0° to 90° for CuKa and from 25° to 180° for CuKa1. The wavelengths used for Cu in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): CuKal 1.54051 A.; CuKa2 1.54433 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn., X-ray diffraction crystallography using tubes with copper targets revealed a need for a handy reference for the quadratic functions of copper radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961

By T. R. Ellis

Minerals Appraisers/Valuers often find great difficulty or failure in attempting to employ the Sales Comparison Approach to the Market Value Appraisal of development and operating stage mineral properties. An important factor generally overlooked is a comparison of net operating income (NOI) margins on a per-unit-of-production basis between mineral properties, whether these be demonstrated or forecast margins. NOI margins can vary greatly between mines or quarries that are producing similar products. Ultimately, the expected NOI margin determines what a buyer is willing to pay for an income producing property. Common criticisms of the sales comparison approach by minerals appraisers are introduced. These are counterbalanced by raising some issues in the way the inputs for the Income Approach are usually derived by minerals appraisers, and by review of some conspicuous examples of the much too common misuse or abuse of the income approach in market value minerals appraisals. Example transaction analyses and sales comparison analyses are used to demonstrate the author?s methodology for adjusting units of resource in his transaction adjustment tables (see APPENDIX). The examples are used as the basis for discussion of ways to employ adjustments for operating economics and many other factors, while cautioning about the potential for double counting. The conclusions include a recommendation that minerals appraisers attempt to apply at least two of the three valuation approaches when appraising the market or fair value of development and operating stage mineral properties, the two being the sales comparison and income approaches.

Jan 1, 2011

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2007

By G. I. Gritsko

In this paper we consider the elements of a distributed information geomechanic monitoring system which is used in computerized mine planning and mining operations control. The automated system is a technical means of geomechanic monitoring, as a complex system of regulated observations, estimation and prediction of geomechanic state of rock mass and workings during underground mining of coal deposits. Geomechanic monitoring at coal mines and the automated system execute data collection, analysis and calculations of geomechanic situation in the panel during planning, development and carrying-out of mining operations for ensuring geotechnical stability of underground mining.

Jan 1, 1996

By Rob Thomas

Adequate load transfer is considered essential for optimum ground support and is increasingly important in weak roof and/or high stress environments. If adequate load transfer is achieved not only can this have a positive impact on the resulting roof behavior, but it may also allow the use of lower and hence more economic densities of roof support. A wide variety of post-groutable cable bolts are currently in use in the Australian coal mining industry, each of varying capacity, design, and grouting methodology. Though all of the cables are supplied with the appropriate steel specification, strength, and modulus data, the Australian coal mining industry does not have access to a comprehensive and comparative database on the corresponding load transfer performance, which is a critical problem. On the basis of the above, this paper describes the methodology and results of a laboratory pull testing program that aims to assess the impact of cable bolt design on load transfer, and specifically, the impact on the capacity and stiffness of the anchorage. As part of the testing program, 19 cables were tested including (1) plain-strand cables installed in holes drilled with 28 to 55 mm diameter drill bits and (2) bulbed and nutcaged cables installed in holes drilled with 42 to 64 mm diameter drill bits. Other parameters assessed included the significance of smooth and profiled wire, wire packing, and expanded geometry bulbs. The main results of the testing indicate that in comparison to plain-strand cables, if the cable is bulbed or nutcaged, the capacity of the anchor can increase by up to 400%, and the peak stiffness by between one and two orders of magnitude. The results also indicate that increasing hole diameter may have a positive impact on load transfer in the case of bulbed or nutcaged cables and a negative impact on plain-strand cables. No conclusive results were obtained with regard to the impact of grout strength on load transfer.

Jan 1, 2012