Search Documents

By B Miles, D J. Williams, J Ahn, T A. Vangsness

The flooding of open strip coal mines in the Bowen Basin and Hunter Valley Coalfields of Eastern Australia has the potential to soften the spoil and floor materials to produce “mud”. This mud can act as a slip plane or weak zone when spoil is dumped into it, resulting in geotechnical instabilities. It is therefore important to understand the mechanisms and degree of degradation likely to occur within coal mine spoil of different qualities.To investigate this, five clay mineral-rich coal mine spoil samples were collected from the Bowen Basin, and each sample was subjected to wetting and drying cycles to simulate degradation that could be expected on wetting-up in situ, with their particle size distribution analysed both before and after degradation. These results were compared with the results of a modified slake durability test, in which the entire sample was tested.The paper presents the results of the accelerated degradation and modified slake durability tests on each of the five spoil samples. These results were related to the physical and geochemical characteristics of the samples, which highlighted their importance. The modified slake durability test may be used to rapidly simulate the expected in situ degradation of coal mine spoil on wetting-up, enabling susceptible spoil materials to readily be identified.CITATION:Vangsness, T A, Williams, D J, Ahn, J and Miles, B, 2018. Accelerated degradation and modified slake durability testing of clay mineral-rich coal mine spoil, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 83–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

On-stream determination of xanthate concentrations can be made by photometric measurements at 313 nm.A simple double-beam instrument was developed for this purpose. A mercury lamp is used as the light source and a composite filter of UGll glass and chromate solution is used to isolate the required spectral region. The light beam is split into two components of approximately equal intensity. One component is passed through a reference cell containing water to a photo detector; the other component is passed through the xanthate solution to a second photo detector. The reference signal controls amplifier gain to eliminate effects of lamp intensity changes and the amplified sample signal can then be used to measure xanthate concentration.Plant trials showed that provided a clear solution free of air bubbles was obtained from an on-stream filter, the instrument indicated the xanthate concentration and operated satisfactorily for long periods.

Jan 1, 1973

By Sergio N. Monteiro

Polymeric matrix composites with dispersed hard particles are being as wear resistant tools in industrial polishing operations. In the present work, the microstructure of epoxy composites with different amounts of embedded diamond particles, up to 30 wt.%, was investigated for the effect on fracture characteristics. It was found that the introduction of diamond particles promoted an increase the porosity of the epoxy matrix. Moreover, the particle morphology associated with a non-uniform distribution within the matrix was responsible for the nucleation of cracks that caused rupture of the composites.

Jan 1, 2006

The mining industry has recognised for some time the importance of supporting programs which serve to educate the Australian public about the socio-economic benefits of mineral resource development. More recently, industry leaders have realised that the future development of the industry will depend on attracting sufficient young people to commit to a career in the industry. Apart from lending support to the traditional education institutions in Australia, the industry now has the opportunity to participate in the development of education programs in museums. Whilst historic, mining-related theme parks such as Sovereign Hill and Coal Creek in Victoria serve very effectively the objective of relating past mining activities to the socio-economic development of Australia, there still exists the need to provide a facility which, under the same roof, excites interest in geology, mining, mineral processing and the role of minerals and energy in modern society. The redeveloped Geological and Mining Museum (the "Mining Museum"), which is located in The Rocks area of Sydney, meets this objective. With the central themes of formation and transformation this new Museum, which aims to be the best of its type in the world, will use modern museum exhibit techniques and the resources of the Minerals and Energy Information Centre to educate the community including teachers and school children. In the best tradition of museums, outstanding mineral and other collections will complement a comprehensive range of interactive, high technology exhibits which will include a number of exploratory "hands on" facilities. Australian companies are joining with Government to fund this exciting new museum. There is still a need for industry professionals to realise that a modern "mining" museum is no longer just a repository for objects of mining heritage but is also an important centre which serves as an important educational and public relations interface. The Education Section of the new "Mining Museum", which is linked closely with the new Minerals and Energy Information Centre, will be working closely with appropriate mining-related Tertiary institutions to develop specific career programs aimed at secondary students who wish to pursue a career in the mineral resource industries.

Jan 1, 1989

By Martin Banda, Gift C. Chisakuta, Moses Chabinga

KCM made a major modification to the Nchanga Tailings Leach Plant (TLP) changing the circuit from feeding post leach thickeners in parallel with leach discharge for solid ?liquid separation to a Counter Current Decantation (CCD) configuration utilising most of the existing equipment. The new circuit is aimed at improving copper recovery from approximately 70% to 79% through enhanced wash efficiency. The re-introduction of CCD circuit at elevated throughput of 46 000-tpd design was made possible due to the EIMCO E-Duc technology design which is an auto-dilution system that enhances solids settling rate. Commissioning (manual operation) which accommodated on-going operational requirements was phased and completed in January 2004. The circuit stabilised in subsequent months and in March alone an all time record copper recovery of 81.8% was achieved which contributed an extra 779 tonnes copper above the plant?s projected production plans. 100% of the project cost was paid back by end of April 2004 This paper discusses the work involved and the challenges faced during the re-commission

Jan 1, 2005

Using a cylindrical hydrocyclone with a long vortex finder as the separator, a batch sizer was developed for the fast comparative sizing of the coarse solids normally encountered in mineral pulps.Operating times as short as 2 or 3 min gave separations ranging from 16 mesh down to the subsieve sizes.Reproducibility was good and sensitivity was adequate for most applications.

Jan 1, 1968

By A. M. Hearn, J. G. Roos

Energy consumption, being a large proportion of the input of the ferroalloy production process, can be measured in terms of the efficiency with which the energy is utilized and the effectiveness with which it is used. The efficiency of the usage of energy revolves around the specific consumption of the energy for the production of the alloy, which encompasses the thermodynamic aspects of the process and is more of a metallurgical function that will not be addressed further in this paper. The effectiveness with which the energy is utilized is determined by the optimisation of the electricity supply from the utility (in this case Eskom). The South African electricity supply industry is on the brink of considerable restructuring, implying changes in ownership, structure and regulation. In other countries, however, restructuring has often seen higher prices. Owing to the diversity of growth prospects in South African markets, Eskom is turning to new market management and generation strategies. In future, Eskom will develop pricing strategies to increase demand from attractive customer segments such as paper & pulp, iron & steel, aluminium, and other metallurgical industries. There will be a broader spectrum of product offerings, including dynamic pricing options and demand-side management incentives. In a future electricity market that will become more dynamic and demanding, it will become increasingly important for electricity consumers to optimise their electricity supply. There are many facets in optimising the electricity supply, which include optimal utilisation of the tariff, integrating energy cost management into the production planning process, implementation of demand-side management actions, modelling, scenario planning (.what-ifs?.), optimisation, maintenance scheduling coordinated with the tariff periods, etc. This paper gives consideration to the status of the development of technology at the manganese alloy works of Samancor at Meyerton, South Africa in order to increase the effectiveness with which energy is utilized.

Jan 1, 2004

By V N. Rudashevsky, F Melcher, J Lodziak, D Klosa, N S. Rudashevsky, M Sitnikova, L Gast

A combination of novel and æclassicÆ methods, namely electric pulse disaggregation (EPD), hydroseparation (HS), preparation of monolayer polished sections, and mineral liberation analysis (MLA) was employed to study ores from platinum pipes (Bushveld Complex, South Africa), pristine PGE mineralisation of the Main Sulfide Zone (Great Dyke, Zimbabwe), as well as ancient and modern gold/PGM placer deposits. It is shown here that the EPD technique liberates mineral grains of interest without any visible destruction allowing the study and analysis of individual rock-forming and ore minerals, in our case especially platinum-group minerals. The HS method is an effective tool in concentrating heavy minerals by factors up to 10 000 fold. As near-total recovery of grains >10 ¦m is achieved, the nugget effect can be overcome also in case of limited availability of samples (drill core, museum specimens). The MLA technique is a fast tool to detect and characterise mineral phases in ores and ore processing products. Many mineralogical parameters of individual grains and mineral assemblages can be deducted and documented. The results show that the techniques employed, either on their own or in combination, provide a wide range of additional information especially on platinum ores which is beneficial to both the researcher and the metallurgist.

Jan 1, 2008

By A R. Cameron

"The number of commercial explosive products available to the mining industry has been steadilyincreasing and associated with this there has been an increase in the range of characteristics or properties of them. This has lead to increased difficulties in selecting the most appropriate explosive for a particular blasting situation. Techniques are available that can be used to evaluate and compare the characteristics of explosives under a range of conditions. Also, the techniques are used to assess the variability in the characteristics between batches."

Jan 1, 1994

By Tian Sugui

By direct aging treated, creep properties measurement and microstructure observation, the influences of the direct aging treatment on the creep behaviors of Hot Continuous Rolled GH4169 superalloy are investigated. Results show that the creep resistance of Hot Continuous Rolled GH4169 superalloy may be obviously improved by directly aged treatment. Under the applied stress of 700MPa at 660, the creep lifetime of the alloy is enhanced to 126h from 60h. During hot continuous rolling, the deformation features of the alloy are the twinning and the double orientations slipping of the dislocation activated within the twinning regions. After direct aging treated, the alloy displays a smaller grain size, and the finer g² phase is dispersedly precipitated in the matrix of the alloy, which is thought to be a main reason of enhancing creep lifetime of the alloy.

Jan 1, 2010

By Steve Dubnewych, Jon Kaneshiro, Calvin Jin

The Joint Water Pollution Control Plant (JWPCP), operated by the Sanitation Districts of Los Angeles County (the Districts), treats wastewater generated by over3 million people and processes wastewater solids generated by over 5 million people. The JWPCP Tunnel and Ocean Outfall Project, if constructed, would be one of the major marine outfall projects in the world. The new tunnel and ocean outfall system would provide relief to the existing outfall and allow inspection, maintenance, and repair of the existing tunnel and outfall system, portions of which were constructed as early as the 1930s. Geologic conditions are challenging along the alignments within the study are a being considered. Conditions include saturated alluvial soils, weak sedimentary rock, mixed face conditions, and squeezing ground conditions. Other significant challenges include the potentials for encountering up to 11 bars of water pressure, crossing seismically active faults, and encountering gassy and contaminated ground conditions. This paper discusses the details of the proposed project and the associated challenges.

Jan 1, 2007

By Robert C. Horton

The Getchell Mine is located on the east flank of the Osgood Mountain Range in the Potosi Mining District, Humboldt County, NV. Mining in the area first began in 1883 for copper, lead and silver in skarn-related deposits. Tungsten was discovered in the skarns in 1916 and was mined sporadically until 1957. The first major discovery was made in 1933 when two Winnemucca prospectors, Edward Knight and Emmett Chase, found gold at the present site of the Getchell gold mine. In 1934, after a small amount of preliminary prospecting, the claims were purchased by Noble H. Getchell of Midas, NV. The Getchell Mine Inc. was organized and exploration and development work began on a broad scale. Major funding was provided by George Wingfield and investors he assembled. Laxalt described Wingfield’s immediate history prior to his financing of Getchell as follows.

Jan 1, 1999

By Dilip I. Patel, Jesus Schabib, W. Allen Mawr, Daniel A. Louis

East Side Access (ESA) will extend Long Island Rail Road into midtown Manhattan via 11 km of tunnels, a new terminal station and associated rail support facilities. The hard-rock tunneling in Manhattan will traverse under Park Avenue and some of the most historically and commercially significant real estate in the world. The soft-ground tunneling in Queens will traverse beneath Amtrak’s Sunnyside Yard and the Harold Inter locking, the busiest rail interlocking in North America. This paper details ESA’s program-wide geo-instrumentation monitoring system for obtaining, processing and presenting all geotechnical monitoring data. Data streams will be real-time, such as from automated total stations, and manually read, such as from optical survey instruments and handheld data loggers. All data will be input into a web-based Geo-Instrumentation Data Management System, which will be accessible to project stake holders via ESA’s intranet or via the Internet using remote access controls.

Jan 1, 2007

By B. H. Caudle, L. G. Loncarie

Pilot flooding is one method of evaluating a proposed secondary recovery project. However, the amount and rate of oil recovery from an unconfined pilot area is not usually the same as from an equal area in a large-scale flood. This is true because fluids are free to move across the boundary of a pilot area. The result is that some of the oil produced in a pilot flood may come from outside the designated area and some of the displaced oil may leave the pilot area completely. This paper presents the results of fluid-flow model studies on a five-spot pilot flood. Mobility ratios between 0.1 and to have been studied. The effects of changing the ratio of injection to withdrawal rates are shown. INTRODUCTION A small-scale field test, or pilot flood, is an accepted method for evaluating the applicability of a secondary recovery operation and the economic potential of that operation for a reservoir. The pilot flood is carried on in the same manner, with the same injected materials and at the same pressures as would be used were the secondary recovery program to be expanded to a larger area of the field or to the entire field. If the reservoir fluid and reservoir rock properties are the same in the pilot area as in the rest of the reservoir, the production, injection and other pertinent data associated with the pilot test will represent and measure what should be expected from a full-scale development of this secondary recovery program. There is one major exception which, unfortunately, has been overlooked by many and which has been awaiting quantitative definition. This is the sweep-out pattern the reservoir engineer must use in interpreting the pilot flood and in extrapolating it to the full-scale development. The sweep-out area in a pilot flood is not contained within the five-spot pattern. Further, there is oil flow into and/or out of the five-spot during a pilot test. Thus, production data from pilots must be interpreted with this different flow system and sweep pattern in mind. We have studied the sweep-out pattern that will exist for some conditions of operation of pilot flooding a single five-spot (four injection wells and one producer). In our study, reported here, we have assumed that the reservoir is relatively homogeneous and of uniform thickness in the pilot area. The results of this study en-able the engineer to predict the recovery, injection requirements and project life for a full-scale operation from the pilot flooding data. The effects of various injection to withdrawal-rate ratios and mobility ratios in a relatively gas-free (10 per cent pore volume or less) system are shown. Experimental Method The technique used in this study was the same as that for the X-ray shadowgraph studies of sweep-out pattern efficiencies.' The model of the pilot and surrounding area was made from a uniform packing of round-grain sand consolidated with an epoxy resin. Fig. 1 shows the relation between the model and the pilot area. Only one-eighth of the pilot area had to be represented in the model because we assumed equal injec-

Author's Note: Since the paper on "All-Flotation at North Broken Hill Limited" was read and discussed, the metallurgical results obtained have conclusively justified the adoption of the All-Flotation treatment.At present the shipping grades of lead concentrate produced from North mine ore range between 74% and 75% Pb, carrying approximately 43 oz. Ag and 4.5%-5% Zn. The lead recovery in lead concentrate is recording 95%-96% of the lead content of crude ore, and the milling and treatment cost on 6400 tons crude ore perweek of 96 hours has dropped to 6s. 3.6d. per ton on ore. With an increased ore tonnage, and with a new mill, considerable further reduction in costs is certain.New flotation machines, with 30 in. vertical depth of overflow (instead of 42 in. depth), are now being tried for the secondary granular treatment, with advantageous results. The treatment to-day is practically the same as that outlined in the paper, excepting that additional concentrate is returned for retreatment in the existing units.(Signed) A. LOWRY.Mr. T. A. READ: The author states (page 356 of Proceedings, No. 79), "The sulphide ore itself was then comparatively coarsegrained, a fact which permitted ready concentration of the galena contents by means of jigs, tables, vanners, etc."

Jan 1, 1931

By Pfeifer H. C, Nicacio P. A D

Sinter has been used as part of the metallic charge in large-scale blast furnaces for many years with the well-known benefits in terms of productivity and fuel consumption. However, because of the high investment in a conventional sinter plant, small blast furnaces and the associated integrated mini steel plants have not taken the advantages of using sinter. Recently KTS Korf Tecnologia Siderurgica, a division of Mannesmann Demag Ltda in Brazil, has developed a mini sinter plant for which the investment is compatible with small blast furnaces. Consequently, it is of great interest to evaluate the economical impact of using sinter in such small-scale integrated steel plants. In order to compare two alternatives, ie 100 per cent ore and 70 per cent sinter in the blast furnace burden, mass and heat balances for the entire operation from sinter plant through the blast furnace and EOF-based melting shop, were performed to evaluate the final production cost of the liquid steel. It was found that, depending on the sinter feed price, substantial savings can be obtained with the use of sinter.

Jan 1, 1999

By Radianto Elprama

For the realisation of the underground railway line RandstadRail in the city area of Rotterdam a bored tunnel is under construction. Diaphragm walls up to a depth of about 40 m were used to construct the building pits for the start shaft, the Blijdorp Station and the end shaft. The water tightness of the diaphragm walls was determined by leakage tests that were executed after the construction of the walls, but prior to the excavation of the building pits. The tests showed satisfactory results with a hydraulic resistance of the diaphragm walls of at least 500 days. To determine the water tightness of diaphragm walls it is recommended to follow the specific procedure as described in this paper.

Jan 1, 2006

By Adrian Coombs, Paul Magowan, Derek Zoldy

Continued development and intensification are fuelling the urgent need for new trunk infrastructure within The Regional Municipality of York and throughout the Greater Toronto Area. Permitting of these projects is increasingly subject to public scrutiny to severely restrict dewatering through construction technologies and the requirement for a comprehensive and effective Environmental Management Plan. Three current projects: one on the York Durham Sewage System and two in the City of Toronto 1.Conventional Design, Tender, Award: 4,150m (13,600 ft.) 2.7m (9 ft.) finished interior diameter soft ground tunnel for York Region’s YDSS Interceptor Trunk Sewer 2.Negotiated Contract: 3,800m (12,500 ft.) 3.5m diameter (11.5 ft.) rock tunnels for Enwave’s environmentally sustainable and innovative chilled water system in downtown Toronto 3.Conventional Design, Tender, Award: 2,200m (7,200 ft.) 3.3m diameter (10.8 ft.) rock tunnel for reinforcement of Hydro One’s primary hydro feed in the downtown core of Toronto These projects exemplify issues such as: EPB tunnel and sealed shaft technologies Substantial permitting requirements associated with dewatering Mitigation of rock creep Congested downtown rights-of-way Deep shafts and confined working compounds Unique scheduling and cost benefits when Owner, Contractor and Consultant can work together cooperatively.

Jan 1, 2007

An understanding of the way that solutes are transported in mining or natural environments is essential to the development of sound strategies for managing waste disposal. Research on miscible pollutant movement in unsaturated porous media is carried out both experimentally and numerically. Results of numerical modelling are obtained by solving the groundwater flow equation and the solute transport equation. The finite element method is employed and comparisons between simulation results and experimental data are found in remarkable agreement.

Jan 1, 1995

By Isobel Yeo, Luca Cocchi, Sven Petersen, Nico Augustin, Sean Plunkett, Ingo Klaucke

Exploration for seafloor massive sulfides is currently mainly focused on investigation for active hydrothermal vent fields. However, most of the resource potential is thought to be related to inactive, large deposits that had enough time to accumulate sufficient tonnage. At the same time, ageing of these deposits will ultimately result also in burial acted by either sediments and/or volcanic deposits. We currently lack the technologies to explore for these deposits in a time- and cost-efficient manner. In the fall of 2012 we used a number of AUV-based technologies to explore and image a sulfide occurrence at the Palinuro Volcanic Complex in the Tyrrhenian Sea (Mediterranean Sea; Fig. 1) where sampling and drilling have documented a buried polymetallic barite-pyrite dominated site (Petersen et al., 2014). Sulfide mineralization is here covered by volcaniclastic and pelagic sediments and only red sediment staining and the presence of few tubeworm bushes indicated recent hydrothermal activity - black smoker venting is absent. We used AUVbased high-resolution bathymetry, sidescan sonar imaging, subbottom profiling, as well as magnetics to describe, in a quantitative way, the previously known sulfide-bearing areas as well as to successfully explore for new hydrothermal sites including large chimney structures (Figs. 2). Additionally chemical sensors (CTD, Eh, turbidity) investigated the water column for signs of hydrothermal activity in areas not previously investigated, but at the end, only weak anomalies were found in the southern part of the summit.

Sep 1, 2014