Search Documents

By M. M. Hassan

This report describes the analysis tools developed at West Virginia University which can be implemented to optimally design coal mine electrical systems. The basic analytical tools for all power systems are the load-flow and short-circuit analysis. Well known programs have been developed for analysis of ac transmission and distribution systems, but they are not applicable to a system which has combined ac/dc distribution, such as a coal mine power system. Furthermore, the topology of a coal mine electrcal system changes continuously due to the movement of the locomotives on the track. In the first section of this report, algorithms for carrying out load flow and short-circuit analysis of a coal mine electrical system are described. Results from the study of a typical coal mine system are presented. In the second section a method is described to optimally size power cables for cyclic loads. The method is based on the development of a thermal-electric model for a low-voltage power cable. Results from experimental verification of the model are also presented. These techniques are useful in the safe, efficient, reliable and economical design of the coal mine electrical power systems.

Jan 1, 1979

By ERIK CHARRIER, HUGH MILLER, JOSEF BOURGEOIS

In this study, a unique excavation system was characterized, utilizing waterjet technology as the primary tool for material removal during rehabilitation of reinforced concrete and shotcrete structural liners. Through empiric testing, this research seeks to validate the hypothesis that waterjet removal of these support systems will result in less unintended damage than conventional removal methods. The intent is to develop a viable technology that will reduce the collateral damage caused to surrounding liners during excavation, improve the adhesion between shotcrete and the substrate for longer lasting ground support, and improve overall safety for workers in underground environments. An analysis on the fracture mechanisms and operating parameters of each method was completed. Instrumented shotcrete panels were physically tested and examined through visual inspection and ground penetrating radar (GPR) to compare substrate damage according to each testing method. After testing was completed, the data strongly indicates that waterjet cutting causes less collateral damage to the surrounding intact liner and substrate when compared to that of conventional impact hammers. This research is intended to provide a scientific basis for additional applied research in the rapid excavation and repair of shotcrete support systems.

Sep 23, 2021

By Pattinaja MA

Mathematical modelling was carried out to determine the probable convergence and vertical stress patterns around a retreating longwall panel in an underground coal mine in New South Wales. An 'Electrical Resistance Analogue' and a program called 'THREED' based on the displacement discontinuity method were used for the modelling. Parts of the obtained results are presented here and compared with some measurements of convergence at the site. The modelled and measured data agree better qualitatively, than quantitatively.

Jan 1, 1986

By Cao rong-jiang, Tang Xin-he

"In ordinary manufacture process of tungsten powder, a preferable intermediate product used is ammonium paratungstate (APT). The particle size of tungten powder made from it through W2OO58 is larger than 1. 0 um. In order to obtain ultrafine tungsten powder with narrow size distribution, a new type of tungstate, hydraziniull tungstate, was studied. Its formula is 5(N2H5)2O·12 WO.s , with tetragonal crystal structure of a=5.821 , c=18. 468. Three methods for preparing hydrazinium tungstate (ART) were set up and ART can be produced by current industrial APT process with little modification of operation and without any change of equipment.Under certain PH and operation condition of the solution from which ART was produced, an autoreduction of tungsten occured, which produced a lower valency tungstate with blue color when ART was heated at different temperatures, in N atmosphere, tungsten bronze, tetragonal W0290 and W02.7E could be obtained respectively. They all have the superiorities, in the production of tungsten powder, of superfine size and narrow size distribution [average size of 0.5um or even smaller.The rate of autoreduction of ART is very fast at elevated temperature. The reduction reaction, which gaves tetragonal WO290, could be handled smoothly without explosion. To research their behaviors at autoreduction temperatures and the products of autoreduction will be new advances of tungsten chemistry and may also serve tungsten industry with new processes and materials."

Jan 1, 1988

By Shaojun Bai

Siderite ore with high phosphorus content was reduced isothermally at 1,050° C with pulverized coal and different dosages of sodium carbonate. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energydispersive analysis of X-rays (EDAX) were used to characterize the samples. The influence of sodium carbonate on the carbothermic reduction process was investigated. Sodium carbonate and its dosage played a considerable role in the carbothermic reduction. The iron particle size in the reduced ore was below 20 µm, and fayalite was abundant without sodium carbonate additive. With a mass ratio of Na2CO3-to-ore of 5% additive, the iron particle size in the reduced ore was generally above 50 µm, and the diffraction intensity associated with metallic iron in the XRD pattern increased. The effect of sodium carbonate on the phase transformation of fluorapatite during carbothermic reduction was also addressed via thermodynamic calculations and aqueous leaching experiments. The results showed that the fluorapatite was not reduced to P2 at 1,050° C, and a portion of the fluorapatite was converted to soluble phosphate. The reduction of siderite can be catalyzed by adding an appropriate amount of sodium carbonate. This catalytic activity was caused by an increase in the reducing reaction activity of FeO and the acceleration of the carbon gasification reactions. The decrease in phosphorous content in the iron concentrate was attributed to an improvement in the separation of the iron phase from the slag phase when sodium carbonate was added and with the formation of soluble phosphate.

By C. H. Li, R. D. Carnahan, R. J. Stokes, T. L. Johnston

When silver chloride deforms by pencil glide at temperatures of 26ºand 72°C, grain size has no effect upon the proportional limit and the material necks down to a knife edge under tension. At -196ºC, deformation takes place on fewer slip systems to produce straight slip traces, the flow stress becomes sensitive to grain size and fracture occurs by cleavage from an intergranular source without any reduction in area. THERE are significant differences between the appearance of the slip bands formed in silver chloride and in the alkali halides at room temperature. The bands in sodium chloride, e.g., are fine and geometrically straight, whereas in silver chloride they are coarse and wavy.' Such differences in the slip behavior prompted us to inquire what the effects of grain boundaries might be on the mechanical properties of these solids. As an introduction to a general study of ionic poly-crystal behavior, we have investigated the effect of grain size on the stress-strain relationships in silver chloride at different temperatures. We have chosen silver chloride chiefly because polycrystals can be easily prepared free from cracks and macroscopic voids by conventional techniques. Moreover, as we shall see, the slip behavior can be readily modified by changing the temperature. It will be shown that the effect of grain size on the yield stress of silver chloride is strikingly dependent upon the temperature of deformation and that this temperature effect comes about through a change in the number of slip systems which operate at the onset of plastic flow. EXPERIMENTAL PROCEDURES Polycrystalline tensile specimens were made by recrystallizing cold-rolled AgCl sheet. Thirty-gram quantities of AR grade silver chloride powder were melted in a low heat capacity furnace, cast into cylindrical forms 3/4 in. in dim and approximately 1 in. in length and then extruded with a 16:l reduction ratio into rods 3/16 in. in dim. Extrusion temperatures were varied from room temperature to 350°C. In order to impart various degrees of cold'work to the extruded rod. All extrusions were then cross rolled to sheet 0.040 in. in thickness at room temperature and machined to form tensile specimens having a gage length of 0.750 in. with a width of either 0.250 or 0.145 in.* Annealing was carried out in an air oven at 200°C for periods up to 20 hr. specimens having average grain diameters ranging from 0.024 to 0.40 mm were prepared by varying the extrusion temperature and annealing time in the conventional manner. To obtain specimens with grain sizes larger than 0.40mm, lightly deformed thin prisims of silver chloride single crystals (supplied by Harshaw Chemical Co.) were recrystallized. Grain size determinations were made by an intercept method and revealed that the grains were equi-axed. Laue back-reflection X-ray patterns showed little tendency to form a preferred orientation texture. Specimens which were to be used for the slip band studies were polished by immersion in fresh boiling concentrated NH,OH for 60 sec. They were then etch polished for 10 sec on each side by hand lapping on a stationary velveteen lap wetted with a dilute Hypo solution (5 g of Kodak Acid Fixer in 100 cc H20). Finally the specimens were rinsed in warm water and alcohol, blown dry and carefully mounted in the tensile machine for testing. Tensile tests were performed at three temperatures, namely, 26º, -72º, and -196°C. A screw-driven hard tensile machine was used at a constant strain rate of 0.006 in. per in. per min. Loads were determined with a light- proof ring fitted with A-18 strain gages and extensions were measured with a 0.0001 in. dial gage. Constant level baths of alcohol with dry ice and liquid nitrogen were used to maintain the two lower test temperatures. EXPERIMENTAL RESULTS Reproducibility—In view of the light sensitivity and reactive nature of silver chloride, it was necessary to determine whether reproducibility depended upon either exposure to light or to the condition of the surface. However, during the course of the work it became clear that variation of laboratory lighting

Jan 1, 1962

By Benjamin F. Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of different types of hammer drills to various mining, quarrying, and excavating operations, that an indication of the 'economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the "rock drills;" that the placing of small holes inclined upward, at angles steeper than 40' above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized. The common test was to fill a measured air receiver with compressed air at a certain gauge pressure, run the drill until the pressure had dropped to too low a figure, then compute from the time, drop in pressure, and

Jan 1, 1915

By Lv Guozhi, Ren Xiaodong, Liu Yan, Dou Zhihe

"This paper investigated a new desulfurizer, dolomite and ferrosilicon. Magnesium vapor produced by silicothermic reduction of dolomite and ferrosilicon in an immersion tube of molten iron was injected into the molten iron by carrier gas through the underpunch of the tube and desulfurization reaction occurred. In order to explore the desulfurization process of molten iron by the new desulfurizer, the thermodynamics, and experiments of magnesium vapor production and desulfurization have been studied. Through thermodynamic calculation, the reaction temperature of magnesium vapor production by 75ferrosilicon and light-burned dolomite is 1838K in the standard state and decreased with the decreasing partial pressure of magnesium vapor, PMg· When PMg=25kPa, the reaction happens at 1673K. From experiments of magnesium vapor production, reduction efficiency of Mg vapor is about 60 % in 15 minutes at 1673K. From hot metal experiments, the desulfurization efficiency is 89.35%, and the lowest sulfur concentration after desulfurization is 46ppm.IntroductionPretreatment desulfurization of hot metal has become a necessary step in modem optimizing steelmaking process for its cheap cost, which can not only liberate of blast furnace productivity and reduce the burden of produce steel, but also effectively improve overall economic efficiency of the iron and steel system[l-ZJ_ At present, injection magnesium particle is one of the two main methods of desulphurization in hot metal owing to its strong affinity for sulphur, low amount of slag produced, low iron loss in slag skimming and low equipment investment[3l. However, there are still some insufficiencies on the hot iron pretreatment with magnesium particles at present[4-5l"

Jan 1, 2013

By C. A. Heiland

WITH seventeen papers submitted. and thirteen presented in three sessions, the geophysicists had a most successful meeting at New York in February. The first paper on Monday morning dealt with the location of a diabase dike near Chapel Hill, N. C., by magnetic and resistivity methods. The magnetic indications were pronounced directly over the dike. whereas the anomalies of apparent resistivity were less distinct and displaced away from the dike. In the second paper, Professor Keys reported on the results obtained with four different methods of depth calculation on known portions of the Falconbridge

Jan 1, 1937

By Dave G. Osborne

With the growing exportation of coal from North America to the Pacific Rim countries and Europe, has come an increasing awareness of the need to determine economically optimized amounts of incombustibles (ash and moisture contents) for the shipped product. Despite the fact that demand bas caused a steady improvement in selling price, particularly for thermal coals, growing production and transportation costs have compelled producers to keep a sharp eye open for ways and means of minimizing the latter since this probably represents the greatest single potential for making savings. Consequently the Coal Industry has become acutely aware of the economic ramifications of eliminating moisture in particular, thereby producing further saving in the cost of transportation of product from the mine to the consumer. There is, however, a lower limit to which dewatering or drying can be taken and this relates to dustiness which is a function of the characteristics of the coal and the methods used for handling and storage during trans-shipment. Overdrying can lead to serious dust losses and difficulties in handling particularly if the coal contains a large proportion of fines. The ways and means for achieving this "happy medium" of optimization in moisture removal are seemingly undergoing gradual modification largely assisted by the following factors. a) Improvement in effectiveness of coal dewatering and drying equipment. b) Improvement in operational availability and utilization of the equipment. c) The development of surfactants, polymer flocculants and other agents which in many cases can be almost tailor made to suit specific applications.

Jan 1, 1982

These pages may be used as order sheets. Mark the number desired opposite title of pamphlet wanted, add your name and address, tear out the sheets and mail them to us. Single orders 25 c. Pamphlets 10 c. each in lots of three or more. Pamphlets 5 c. each in lots of fifty or more. These prices prevail for orders for pamphlets of the same or different titles, when cash accompanies order. The pamphlets listed on the following sheets are advance copies printed to facilitate discussion at the meetings of the Institute. They are offered for sale at the reduced prices given above as long as-the supply lasts. This list is published in the Bulletin in order that members may have the first opportunity to secure pamphlets, which sometimes are in such great demand that the supply is exhausted before the wants of members can be supplied. The following list includes only a fraction of the pamphlets that have been published by the Institute. Any other paper published by the Institute may be obtained for the price of $1, except those published in Volume XXXI, which are rare. The Institute is still selling back volumes of Transactions at reduced prices, but some of these volumes are becoming rare and members who desire to complete their sets of these very important books on mining and metallurgy are advised to send in their orders as soon as convenient. (See Advertising page 15.) , The attention of members is also called to the bibliographical index of the science of ore, deposits contained in the Emmons Volume which is selling at $3 in paper and $4 in half morocco. The Posepny Volume is already exhausted and members who do not get in their orders for the Emmons Volume at the present reduced price may soon find themselves unable to obtain it on such favorable terms.

Jan 6, 1917

By V Lishchuk, C Lund

"Geometallurgy aims to improve resource efficiency by creating a spatial model of an orebody in order to forecast ore processing behaviour. This enables calculation of the economic value of each ore block and the use of this information for production optimisation and hence an improved economic return. Modelling uses different approaches to link geological information with mineral processing: traditional approach uses chemical elements; proxy approach – small-scale geometallurgical tests; and mineralogical approach – minerals.A geometallurgical model is obtained during execution of a geometallurgical program encompassing the entire value chain of ore processing. Available methods for establishing a geometallurgical model are in many cases limited and not yet comprehensively validated. Some of the limitations include: sampling density, assaying methods and quality, forecast accuracy block model content, geostatistical solutions for non-additive components, blending and assessment of positive impact of geometallurgy on the project. Synthetic ore models combined with process simulations and production scheduling, based on strong case studies, present a viable way to address these shortcomings. Such synthetic ore models will have realistic elemental and mineral distribution, textural attributes and 3D variability for input into the design of an appropriate geometallurgical program.A synthetic orebody was created for an apatite-bearing iron deposit. Variability in modal mineralogy was described by geostatistical parameters combined by a set of linear and trigonometric functions. The generated synthetic deposit model was used to develop a mine production plan to generate a simulated process feed. The process feed had detailed information required for beneficiation process simulation: modal mineralogy, chemical composition of minerals, grain size and specific gravity. The synthetic system was used to measure benefits that a geometallurgical program developed for real cases could provide, compared to production where only head grade is optimised. These include a reliable sampling strategy and confidence in the feed-quality forecast for economic evaluation.CITATION:Lishchuk, V, Lund, C and Lamberg, P, 2016. Development of a Synthetic Ore Deposit Model for Geometallurgy, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 275–286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By M Gasparon, J Harris, T Baumgartl, D J. Williams, M Edraki, P A. Kirsch, D Rowe

RISKGATE, an Australian Coal Association Research Program-funded (ACARP) initiative, has been designed to assist the Australian coal mining industry in improving minimum standards for safety performance, efficiency, operating practice and training. The online system is innovative in that it is built upon a foundation of industry expert knowledge gathered through action research workshops, which is further supported by a broad array of industry, academic and technical resources. In operation, RISKGATE offers a continuum for knowledge transfer and communication of current practice in risk identification, assessment and management in the coal mining industry. The primary mission of RISKGATE is to focus industry attention on prioritising control management as a way to achieve acceptable risk.A Coal Mine Tailings Dam Module has recently been added to the RISKGATE suite. The key risk, or initiating event, associated with coalmine tailings dams is catastrophic failure of the dam, leading to the release of tailings and water. This can occur due to geotechnical instability of the dam itself or of its foundation, overtopping and erosion of the dam, and piping failure of the dam itself or of its foundation. Coalmine tailings dams are also prone to seepage into the foundation and through the dam, particularly during operation when large volumes of water are discharged with the tailings. The most significant risk associated with seepage is the release of potentially contaminated water to the environment. Contamination can take the form of elevated salinity, acidity and dissolved metals. Run-off from coalmine tailings can cause erosion and can also potentially contain contaminants. Desiccation of the tailings surface can result in dust generation and dispersion.The paper presents the background and context of the RISKGATE project, the need for the addition of the RISKGATE Coal Mine Tailings Dam Module, and a description of the developed module, including the five initiating events considered, their causes and associated preventive controls, and their consequences and associated mitigating controls. This paper concludes with a discussion of the ways in which Australia’s coal mining companies are starting to apply the RISKGATE body of knowledge at their sites, which will flow onto the management of their tailings dams.CITATION:Williams, D J, Kirsch, P A, Gasparon, M, Baumgartl, T, Edraki, M, Rowe, D and Harris, J, ?2014. Application of RISKGATE to coal mine tailings dams, in Proceedings Life-of-Mine 2014 , pp 219–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By I. H. Warren

The high temperature lubricant molybdenite, MoS2, is usually produced by a complex sequence of processes involving mineral dressing of molybdenite concentrates followed by leaching with hydrofluoric acid to remove abrasive impurities such as silica (1). Many attempts have been made, mostly by techniques involving, direct fusion of molybdenum compounds with sulphur, to produce synthetic molybdenite. However, apart from some experiments of geochemical interest (2) in which aqueous solutions of sodium sulphomolybdate, Nat MoS4, were decomposed under pressure at temperatures between 300°C and 700°C, no attempts to produce the mineral by hydrometallurgical procedures have been reported. Since molybdenite is nominally a compound of tetravalent molybdenum with sulphur, and the most common state of molybdenum is +6, production of molybdenite is likely to involve reduction and sulphidization. The present study, therefore, describes the reduction, with hydrogen and carbon monoxide, of molybdenum in the hexavalent state in alkaline aqueous solutions containing sulphide ion. In these

Jan 1, 1972

By Anderson Alves Cunha

Diante do cenário macroeconômico internacional, o setor mineral busca soluções inovadoras e sustentáveis para seus processos produtivos. Uma dessas soluções é, sem dúvida, aumentar a recuperação do mineral de interesse presente no rejeito proveniente de operações de beneficiamento de baixa recuperação metalúrgica. A substituição de matérias primas naturais por resíduos abre uma gama de oportunidades para melhorar a gestão de recursos não renováveis, contribuindo significativamente para o desenvolvimento sustentável e competitividade do negócio. O presente trabalho tem o objetivo de definir qual a faixa granulométrica, existente na lama, é mais adequada para concentrar e produzir pelotas, considerando a composição química, perda por calcinação, mineralogia e quantidade de elementos deletérios. Para isso, foram utilizadas técnicas de caracterização tecnológica, como: classificação granulométrica (peneiramento a úmido e cyclosizer), fluorescência de raios X, difração de raios X e microscopia óptica. Os resultados do trabalho permitiram identificar uma faixa granulométrica com alto teor de ferro e alto grau de liberação dos minerais de ferro, porém com teores de quartzo acima que um pellet feed comercial. Sendo assim, um determinado tratamento de concentração ou um blend será necessário para adequar quimicamente o material, para posterior obtenção de pelotas com baixo custo.

Aug 17, 2017

By Mehmet Ali Recai Önal, MAHMUT CAMALAN

Mineral liberation is one of the primary objectives in comminution circuits for the downstream separation of valuable minerals. Breaking minerals through their grain boundaries (grain-boundary breakage) enables mineral liberation in their natural grain size, removing the need for intensive grinding. This study aimed to evaluate if gaseous carbon dioxide, oxygen, or hydrogen can be used as grinding additives to promote the liberation of chromite grains by grain-boundary breakage. For this purpose, chromite ore particles in the −9.53 + 6.35 mm size fraction were pretreated by exposing them to carbon dioxide, oxygen, or hydrogen flow. Then, the untreated and pretreated samples were broken in a drop-weight tester under the same conditions. Finally, the graderecovery plots of chromite grains in the selected progeny size fractions and the overall progeny distributions were measured and compared. Pretreatment with carbon dioxide flow was found beneficial for grain-boundary breakage. It significantly enhanced the liberation of coarse chromite grains along with the overall progeny fineness. EPMAanalysis showed that the adsorption of carbon dioxide seems to reduce aluminum concentration at grain boundaries, which could be the reason for grain-boundary weakening. These results suggest that carbon dioxide can be used as a grinding additive, reducing the carbon footprint of the mining industry.

Oct 29, 2020

By G. M. Wolfaardt, B. C. Qi

"From a lifecycle point of view, biologically digested sludge is a valuable product that should be reused if possible. Sludge may be applied to agricultural land for further sludge treatment and improvement of the characteristics of the soil. The characteristics of sludge that affect its applicability for soil conditioning include moisture content, pathogens, nutrients and metals. In this paper, the use of solid anaerobic digestion sludge of the lignocellulosic residues to condition soil was investigated in regards to nutrient composition, water content/retention capacity, hygienic quality (contamination of pathogenic bacteria) and heavy metal adsorbing/releasing characteristics of the sludge.It was found that the digested sludge had approximately 44.5% free and immobilized water and 46.9% bound water. The water-holding capacity of the sludge was high. This was a merit to apply the sludge to agriculture in dry areas. Anaerobic digestion under thermophilic conditions showed a promising disinfecting effect to the sludge, in contrast to the landfill digestion. The anaerobic digestion sludge could be considered as a humus-rich hygienic product that improves soil fertility and water holding capacity, nourishes plants and immobilizes heavy metals in the environment"

Jan 1, 2003

By Marvin L. Whisman

Several parameters controlling the reproducibility of tritium determina¬tion in organic compounds by liquid scintillation counting were evaluated by the Federal Bureau of Mines. These included optimum volume of scintillator solution for maximum counting efficiency, reproducibility of counting a sealed commercial standard and comparison with duplicate counts on laboratory-prepared samples. The error introduced by using microliter pipets, optical differences in counting vials, reproducibility of counting organic samples where quenching is a factor, reproducibility of counting laboratory-prepared samples with an added internal standard, optimum ratio of internal standard activity to sample activity, effect of sample volume upon counting efficiency, count rate at which coincidence losses become apparent, and reproducibility of organic compound radioassay by the standard addition technique are outlined. From the evaluation of these parameters, a technique that can be applied routinely to organic compounds containing tritium has been established, and details are included in this report.

Jan 1, 1961

By R. E. H. Pomeroy

Early in 1917, it became evident, owing to existing and pending market conditions, that a substitute for crude petroleum must be found for firing the smelter furnaces. After a review of the plants then existing, it was deemed advisable to depart from their practice and to adopt the following described system of distributing pulverized coal to the furnaces. The principal advantages of the proposed system, which influenced this decision, were: (I) Equal safety; no pulverized coal is stored at the furnaces; (2) greater ease of operation, furnace fires being controlled by regulating valves in burner branches, as in gas firing; (3) better organization; all machinery, including pulverized coal feed, is under one roof, and the organization is separate from the furnace department; (4) greater cleanliness; all machinery is under vacuum; (5) greater flexibility of application, the coal and air mixture can be piped where needcd. The design of the plant is the result of the combined efforts of the local engineering staff and of the machinery manufacturers. Many new features were embodied in this design to insure greater safety, cleanliness, and efficiency of handling. After 14 months of continuous operation, the plant has proved entirely satisfactory. The building is of structural steel, covered with corrugated steel, with many windows and is painted light gray inside and out. The building floor is of concrete with ample drains to the sewer, and the building is equipped with fire and service water piping. Fig. 1 shows the east side of the building and the incline conveyor from the raw-coal bins. The plant is operated entirely by electric power. All alternating current is 550 volts, 3-phase, 60 cycles. The pulverized-coal feeding niotors and control mechanism are operated by 220-volt direct current supplied by motor-generator sets in the building. Autamatic push-

Jan 1, 1921

By R. E. Chaney

This report summarizes the research on the Strategic and Critical Materials Program tasks conducted at the Idaho National Engineering Laboratory (INEL) between May 1984 and April 1985. The work is divided into two areas: 1. Production Technologies - Tasks directed at developing advanced extraction technologies ? Biologically-Assisted Minerals Processing ? Metal/Gas Reactions and Thermal Plasmas ? Dehydration of Aluminum Chloride Hexahydrate (completed). 2. Conservation/Substitution Technologies - Tasks directed toward establishing the technical processing base which will permit the use of advanced materials ? Joining of Rapidly Solidified Alloys (RSA) ? Joining of Silicon Nitride-Based Ceramics ? Nondestructive Evaluation of Ceramic and RSA Joints and Materials ? Substitute Catalytic Materials for Platinum.

Jan 1, 1985