Search Documents

By Chuanyao Sun, Zhenguo Song, Aijun Ren

"Lead-Zinc sulfide ore containing carbon is one of typical refractory resource. Because organic carbon has natural floatability, it has a great negative influence on flotation of lead-zinc sulfide ores. It is difficult to obtain qualified lead concentrate by flotation using conventional reagent system. In order to reduce the influence of organic carbon on lead and zinc flotation, two alternatives, i.e., removal carbon by pre-flotation or adding carbon depressant in lead and zinc flotation, can be adopted. If the flowsheet of removal carbon by pre-flotation is adopted, the lead and zinc recovery which are lost in the carbon tailings is often higher. If conventional carbon depressants are used in lead and zinc flotation, it has a certain depression effect on lead minerals. In the paper, the ore grading 1.49% Pb, 5.73% Zn, and organic carbon 3.14% has been carried out by flotation tests. In the bulk flotation of carbon and lead minerals, Pb concentrate is only about grading 21.00% Pb. In the pre-flotation of organic carbon, it’s hard to remove most of carbon, and the loss of Pb and Zinc recovery is too much in carbon tailings. New carbon depressant BK547 and three conventional carbon depressants including sodium lignosulphonate, Fe-Cr-lignosulfonate, and dextrin, are used in comparative tests of Pb flotation, and results show that BK547 have a good depression on organic carbon, and have almost no effect on Pb flotation. Using BK547 as carbon depressant, cycle test in flowsheet of two-stage Pb and Zn selective flotation and coarse concentrate regrinding have been carried out, and results show that concentrates grading 62.51% Pb and 41.33% Zn are obtained at recoveries of 70.24% Zn and 83.58% Zn.INTRODUCTION Lead and zinc mineral resources are still the main source of lead and zinc metal. For lead-zinc sulphide ore, lead concentrate and zinc concentrate are obtained by flotation. Minerals separation by flotation is a complex process and is dependent, along with other factors, on the relative distribution of hydrophobic (e.g. collector, polysulfide, elemental sulfide) and hydrophilic (e.g. metal hydroxide) species between different particles of the same mineral phase and between mineral phases (Piantadosi & Smart, 2002; Boulton, Fornasiero & Ralston, 2003). Organic carbon has natural floatability and is often associated with lead-zinc sulphide ores. If the content of organic carbon in the ore is more, the flotation index will become worse. The main problem is that the concentrates has too low grade to be qualified grade products for sale. At the same time, the consumption of reagents is more than ordinary ores without organic carbon. In order to solve the influence of organic carbon on the flotation of lead and zinc and other sulphide ores, a lot of research works have been carried out."

Jan 1, 2018

By George E. Blandford

A deterministic model to assess the hydrologic impact of small watersheds subjected to unsteady storm events is presented. The overland flow model is based on the kinematic wave approximation coupled with a Green-Ampt infiltration equation. The Green-Ampt infiltration parameters are estimated using the USDA-ARS parameter estimation technique which is based on soil moisture-tension data. A Galerkin finite element formulation of the kinematic wave approximation is presented for the deterministic analysis of overland flow on small watersheds. The finite element formulation includes linear, quadratic and cubic Lagrangian one-dimensional spatial elements. A linear time variation is assumed which includes both explicit and implicit time marching algorithms, depending on the choice of the time weighting parameter. The implicit time algorithms result in a system of nonlinear equations which are evaluated using a modified Newton-Raphson iteration scheme. Initial solution estimates are generated using a linear finite difference procedure. The coupled infiltration overland flow model is tested using storm data for impervious surfaces, a laboratory soil flume, and two natural, USDA-ARS experimental watersheds.

Jan 1, 1983

By M. B. Kime

"Discrete-element method (DEM) modelling is a powerful tool for studying particulate systems within the mineral processing industry. DEM simulations were conducted to investigate the power draw, load behaviour, and impact energy profile of an experimental ball mill under different milling conditions. The variables considered were mill rotational speed (percent critical speed), ball size, and lifter face angle. The simulation results indicated that the grinding efficiency would be enhanced by using 80% critical speed, 30 mm ball diameter, and 45° lifter face angle. These findings can be useful in guiding actual ball milling tests involving an ore sample.RÉSUMÉ La modélisation par méthode des éléments distincts (MED) est un outil puissant qui permet d’étudier les systèmes particulaires au sein de l’industrie de traitement des minerais. Des simulations par MED ont été menées de façon à étudier le profil de la consommation énergétique, du comportement de la charge et de l’énergie de rupture d’un broyeur à boulets expérimental dans diverses conditions de broyage. Parmi les variables prises en compte figuraient la vitesse de rotation du broyeur (vitesse critique en pourcentage), la taille des boulets et l’angle de coupe de la cornière élévatrice. D’après les résultats de la simulation, on pourrait améliorer l’efficacité de broyage en utilisant une vitesse critique de 80 %, un diamètre de boulet de 30 mm et un angle de coupe de 45 ° de la cornière élévatrice. Ces résultats peuvent se révéler utiles pour les essais concrets de broyage à boulets impliquant un échantillon de minerai.INTRODUCTIONComminution is a very energy intensive process. It consumes approximately 5% of the electricity produced worldwide and more than 50% of the total energy used in mineral processing plants (Pokrajcic, 2010). Among all the comminution stages, ball milling is one of the most energy intensive processes. In ball mills, rotational movement provides the rise of the load and the media that are projected and impact on the mill shell at lower angular displacement, resulting in particle breakage. Ball mills are able to reduce particle size over a relatively wide range of particle sizes. This explains their wide applicability in research laboratories and the mineral processing industry."

Jan 1, 2017

By A. Rodriguez-Prado

"Magnetic fields affect the growth of cultured cells and plants; however, limited information exists about their effects on vegetation performing environmental remediation. Constructed wetland mesocosms treating hexavalent chromium (Cr(VI)) wastewater exposed to low-intensity magnetic fields (60 Hz, 56.5 × 10-6 Tesla) produced 100% more biomass than the unexposed control. Nonetheless, they removed only 43 ± 27% of Cr(VI), compared to 60 ± 21% for the control. A Cr(VI) reduction expression was developed as a function of the magnetic field. The design and operation of constructed wetlands to treat mining wastewater can be corrected for magnetic field effects.RÉSUMÉ Les champs magnétiques affectent la croissance des cellules et des plantes cultivées; toutefois, il existe peu d’information quant à leurs effets sur la végétation utilisée à des fins d’assainissement environnementale. Les mésocosmes des marais artificiels traitant des eaux usées, contenant du chrome hexavalent (Cr(VI)), exposés à des champs magnétiques de faible intensité (60 Hz, 56,5 × 10-6 Tesla) ont produit 100 % plus de biomasse que le contrôle non exposé. Néanmoins, ils n’ont enlevé que 43 ± 27 % du Cr(VI), comparativement à 60 ± 21 % pour le contrôle. Une expression de réduction du Cr(VI) a été développée en tant que fonction du champ magnétique. La conception et l’exploitation de marais artificiels pour traiter les eaux usées des mines peuvent être adaptées pour tenir compte des effets des champs magnétiques."

Jan 1, 2015

By V K. Panwar, Sampat Raj

At a Fertilizer plant located in the southern part of India, 74 numbers of pump foundations have shown non-uniform settlements causing the tilting of pump foundations under self-weight primarily due to the presence of varying thickness of the heterogeneous subsoil beneath the pump foundations and soil erosion because of water seepage through deeper excavations in the close vicinity. Various corrective measures have been explored and taking due cognizance of the prevailing subsoil conditions, site constraints, and constructability aspects, micropiling has been adopted. This paper presents the site problem and details of remedial measures adopted for rehabilitation of the distressed pump foundations. The main objective of this paper is to provide guidelines for designer during design and detail engineering stage to avoid similar nature of problems and also to provide a solution concept to tackle similar nature of problem(s) if encountered at site.

Nov 1, 2022

By M. J. Kanda, T. R. Stacey

Thin spray-on liners (TSLs) have been used as sealants and rock support in tunnels for over 25 years. Laboratory tests have indicated satisfactory properties that can provide adequate strength, adhesion, toughness, and elasticity as part of rock support systems in mining excavations. These characteristics are, however, not always demonstrated in practice, when mine environmental conditions do not correspond with laboratory environmental conditions. The shortcomings of TSLs experienced in the mining industry have raised concerns, resulting in scepticism from some operators regarding their utilization. The research described in this paper aims to investigate TSL performance in environmental conditions similar to those experienced in mines. Brazilian indirect tensile (BIT) specimens were prepared from precast shotcrete and coated with TSLs. The specimens were then exposed to different environmental conditions for up to 112 days before BIT testing under various conditions: laboratory room temperature and humidity; saturated room temperature; and combined saturated and high temperature (50°C). Additional uncoated shotcrete and TSL BIT specimens were prepared for comparison purposes. The results of the BIT tests showed that environmental conditions have a significant influence on the tensile strength enhancement of shotcrete by TSLs. Water-based TSLs are most likely to be suitable for high humidity environments, although their performance decreases at higher temperatures. Numerical modelling of TSL-coated BIT samples confirms the potential limitations of designing TSL support based only on laboratory testing carried out under room conditions.

Jul 1, 2021

By F. B. Plummer

PROGRESS during 1940 in oil-production technology has been confined largely to a steady advancement in practices inaugurated in previous years, rather than the introduction of any new startling process or technique. The usual changes, improvements and additions in production equipment have been introduced. An increased attention to, and interest in, research has been noteworthy, resulting in improved efficiency in operation of oil wells. control, utilization of reservoir energies and reduction of production costs.

Jan 1, 1941

By Raymond L. Carpenter

The thermal conductivity, electrical resistivity, and Seebeck coefficient for nine compounds, based on the formula for enargite Cu3AsS3, were measured in a search for efficient materials to be used in thermoelectric generators or refrigerators. Results indicate that one of these compounds, Cu3SbSe4, has thermoelectric properties approaching those of bismuth telluride. An investigation of the effect of adding small quantities of tellurium to Cu3SbSe4 and Cu3SbS4 in order to improve their properties also was made. A figure of merit of 2.1 x 10-4 °C-1 was obtained for Cu3SbSe4 + 0.1 percent tellurium.

Jan 1, 1963

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open-pit and underground mines of all sizes are regularly collecting point cloud data as laser scanning (LiDAR) and photogrammetry surveying devices have become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely and safely, rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing. This article specifically focuses on digital outcrop modeling and digital terrain engineering. Point clouds. The high-resolution and increasing availability of point cloud technology is rapidly improving open-pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations and typically the reflective intensity and/or the visible three-band color of each point (Fig. 1).LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device.Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles and even in a mobile backpack shown in Fig. 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds,” but this article does not address these due to their higher cost and lower versatility and mobility."

May 1, 2016

By Ballard H. Clemmons

THE future of the steelmaking industry of the Birmingham, Ala., district is closely related to and, in a large measure, dependent on the development of workable, economic processes of ore concentration. Operations thus far in the area have been possible only because of the fortuitous occurrence of iron ore, fluxing stone, and coking coal-all the primary iron-making materials- within a 25-mile radius of the blast furnaces. Commercial ore of the district consists mainly of a 10 to 20-ft hematite-calcite-silica bed locally known as the "Big Seam," a component of the Clinton formation of Silurian Age. At present mining rates, this ore will be available for a number of years. It is largely mined under 1000 to 2000 ft of cover and transported on 15 to 20" slopes that, in some instances, are as much as 10,000 ft long. Under these conditions, particularly with increasing distances from face to portal, mining costs are gradually becoming disproportionately high. Although not a major factor thus far, it should also be noted that the average annual ore output of the district is gradually be- coming more siliceous.

Jan 1, 1950

By P. Ramsaywok, S Ndanduleni, G. Legodi

The objective of this paper is to share the optimisation journey of a pilot Reflux classifier (RC) circuit in the Exxaro GG1 plant, at Grootegeluk beneficiation complex in Lephalale, South Africa. The RC circuit was commissioned in 2016 to produce semi-soft coking coal at its fines circuit; however the stability of operation as well as the quality control of the coal product was not fully achieved. Various test campaigns and optimisation studies were conducted to understand and optimise the RC circuit at GG1. The studies revealed circuit design inefficiencies; provided an improved technical understanding of the current pilot circuit and the parameters required for the circuit to reach a stable operation. The operation was stabilised with its current inefficiencies to produce an average 12.5% ash semi-soft coking coal product for sustained periods, above the initial target of 10.3% ash. Keywords: Reflux classifier, coal

Jan 1, 2020

By P. J. Ehret

By and large, I agree with many of the precepts discussed in the Saperstein paper. I believe there is much more that can be done on the local level to involve both government and planning in the mine permit review process. Admittedly, much can be done to improve discussion between the state regulatory authority, local authorities, and mine operators. However, I strongly disagree, as suggested in the paper's conclusion, that such a system, as outlined in Saperstein's paper, could result in a reduction of review time or a lowering in the cost of permitting. The implementation of such a system by its very nature would only add a new level of bureaucracy to an already cumbersome process. This system, in my opinion, would only add to the cost of permitting and the time necessary to obtain a permit. Admittedly, it would achieve the result of adding local influence into the permitting process, but at what off-setting cost? It has been my professional first-hand experience and observation in the permitting and lands unsuitable processes to note that under the present system, local governments that do feel they have a stake in local mines and actively advocate their position (not simply comment), have had significant input into the conduct of mining and reclamation plans in their areas. Mining companies that mine in these areas are aware of local interests and attitudes, and do consider them in their plans. Simply put, local governments that want to get involved and want to play significant roles can and do. Those that do not advocate a position or have no input to offer do not. Although the present system is not as direct in effect in regard to local control as Saperstein's, it does work. It does so without the red tape that would result from developing miniature regulatory authorities in every county in which mining occurs. Although local input is important, there are many more sections of the Surface Mining Control and Reclamation Act (SMCRA) than Sections 508(a)(8) and 522(a)(3)(A) that also are important. It appears Saperstein's paper may overindulge these sections. An additional specific comment is made in regard to the statement that while local areas benefit from mining (wages, salaries, and purchases), they also endure environmental deterioration caused by mining affects. It is believed that the whole purpose for which SMCRA and its resulting regulations were enacted and developed was so mining would not be permitted if significant environmental deterioration could occur. Therefore, it could be argued that this point under current law is moot.

Jan 1, 1985

By The Mill Staff

Introduction The Hollinger cyanidation mill commenced operating in June, 1912, and 49,779,978 tons of solids had been discarded by the end of 1950. The present tailing disposal plant has been in operation since 1924 and holds 39,762,250 tons. The tailing disposal plant is on the property of Kayorum Gold Mines, Limited, about a mile and a quarter south of the mill. The area available for tailing covers 640 acres and is roughly l ¼ miles long by ¾ mile wide. Tailing was first deposited on the McKay veteran claims, l mile long by 1/2 mile wide, which were later included in the Kayorum property. This site sloped from northeast to southwest, the slope amounting to 106 feet between the northeast corner and the low land to the southwest. The low land was wet and a considerable area was covered with muskeg up to 17 feet deep. It was drained by a brook running across the property in a southwesterly direction. Later, when more ground was needed, the low-lying mining claims adjacent to the south and west boundaries were acquired to allow for the extension of the plant. This entailed some extra difficulties and expense that would not have been encountered had the whole of the present site been acquired with the original purchase. At the present time, the top of the tailing deposit stands at two elevations, but eventually the tailing deposited on the extension to the original plant will be raised to the same height as the older deposit. Previous to 1924, all of the tailing was deposited on Low land and in lakes near the mil1. Between 1924 and 1926 an increasing tonnage was sent to the McKay claims until, in 1926, all of it was being sent there. In 1936, the area of the deposit was extended and shortly afterwards all of the tailing was deposited on the new site.

Jan 1, 1951

By Autumn Fjeld

The filling and solidification of an industrial scale composite casting has been simulated to investigate the re-melting of the outer shell material during casting. Production of a composite requires a two-step casting process which includes centrifugal casting of a hard outer shell material and subsequent conventional ingot casting of a tough core material into the shell-mold assembly. During casting of the core, a thin layer of the shell material re-melts and mixes with the core material producing a bonding layer of intermediate composition. The present numerical model employs the volume of fluid method and an enthalpy-porosity technique to couple the filling of the core material and re-melting of the shell material. The interface between the two materials is tracked and can be used as a guide to examine the extent of melting and, to some degree, mixing of the two fluids and species diffusion.

Jan 1, 2008

By E Villaescusa, C Drover

The stability of access tunnels is one of the main engineering challenges in deep underground mine construction. Many underground hard rock mining operations are now reaching depths where the induced stresses are such that sudden and violent failure of the excavations can occur very soon after construction. The loading conditions on the installed ground support schemes are often underestimated by conventional engineering design methods. Therefore, the actual loading conditions often exceed the installed ground support capacity. This can result in failure of the excavations and, in extreme cases, potentially closure of mining operations amounting to hundreds of millions of dollars in lost production. More frequently, violent excavation instability at great depth causes operational delays, costly and unplanned rehabilitation, as well as risks to worker safety. In order to address this challenge, this paper briefly summarises a modern, innovative approach to the design and construction of mine development at great depth. The process follows seven main steps. The first step is to characterise the rock mass strength, structure and stress. The second step is a stability assessment, which identifies the plausible modes of excavation failure, based on the rock mass characterisation. The third step is the definition of an excavation geometry which is harmonic to the high stress conditions. The fourth step is to prepare a site-specific face destressing drill and blast design which will reduce the potential for rock mass instability during the development construction cycle. The fifth step is to accurately quantify the expected loading conditions on the installed ground support. The method of doing so is uniquely analytical and probabilistic. It is based on the natural mechanical relationships between rock strength, structure, induced stress and the physical characteristics of the instability, including its mass and ejection velocity. The sixth step of the design process is to specify a ground support scheme arrangement with sufficient strength and displacement capacity to exceed the rock mass demand by a safe margin. The final stage is to install the complete ground support scheme using mechanised technologies which minimise the exposure of the equipment operators to unsupported ground at the tunnel face.

Nov 29, 2022

By Jeferson Preti

Este trabalho apresenta a análise, o projeto e o desenvolvimento de um manipulador robótico industrial de baixo custo para linhas de produção. O aparato proposto possui potencial para contribuir na melhoria das condições de utilização de células robóticas no cenário industrial nacional, auxiliando na superação dos desafios existentes na implantação de células robóticas por pequenas e médias empresas, nomeadamente, custos de implantação, manutenção e reprogramação/reconfiguração. O manipulador robótico industrial foi projetado considerando uma estrutura metálica leve de baixo custo, com elementos mecânicos de precisão média e não dedicados, facilmente encontrados no mercado nacional. Além disso, o manipulador robótico foi projetado para ser capaz de alcançar velocidades médias provendo tempos de ciclo de operação quase equivalentes aos apresentados por robôs polares articulados convencionais, nas mesmas aplicações. O sistema de controle foi concebido para não empregar o dispendioso sistema convencional de hardware centralizado de controle de eixos, sendo esta operação realizada por algoritmo computacional executado no mesmo PC responsável pela gestão e integração dos processos. Assim, a operação emprega dispositivos acionadores descentralizados considerando o envio dos sinais de referência diretamente aos acionadores, possibilitando a compensação das restrições dos esforços da estrutura com recursos de suavização de trajetórias. A integração com o usuário foi projetada para possuir uma interface gráfica de manipulação amigável e que permita facilmente os processos de operação, manutenção e de reconfiguração. Fornecendo ainda, recursos de supervisão, histórico de falhas e assistência remota. Por fim, um protótipo do manipulador robótico industrial proposto é apresentado demonstrando as principais características construtivas e operacionais.

Jul 30, 2018

The global mining industry will always face significant challenges. Some, though, are bigger than others. What do you consider the major challenges facing the mining industry as a whole and SME in particular? Without a doubt, the major issue in both coal and metal/nonmetal mining industries is the ?graying? of the workforce in all aspects of mining. As the baby boomers continue to age, valuable experience is being lost by industry, government and academia. And there is the potential for SME to lose some of its membership. Now with that said, I should note that, despite the aging of the workforce, SME membership continued to grow by 7.1 percent during 2011.

Jan 1, 2012

By C. Ndou, T. Mothupi, H. Mandende

The technological advances in efficient, rapid, and non-destructive hyperspectral core logging systems for systematic mineral mapping have led to the discovery and exploitation of new mineral deposits Hyperspectral imaging in the long-wave infrared range has been recently used successfully to identify various phosphatebearing minerals (monazite, xenotime, and britholite), with limited work on apatite associated with mafic-ultramafic layered intrusions. In this study we investigate the effectiveness of a hyperspectral imaging (HSI) system with long-wave infrared (LWIR) bandwidthsto identify apatite in the Upper Zone of the Bushveld Complex. The accuracy of the HSI results was validated by mineralogical and geochemical data. The two apatite-enriched zones detected by HSI suggesting widespread development of apatite throughout the uppermost 600 m of the Upper Zone. The lower apatite-enriched zone is approximately 40 m thick, while the upper apatite-enriched zone is about 23 m thick, consistent with previous thickness determinations by traditional logging and analytical methods. Spectral mixing observed in the response of apatite is ascribed either to the common association of apatite and olivine in these rocks, or to differences between the spatial resolution of the hyperspectral image and the size of apatite grains. The VNIR-SWIR wavelength region did not show prominent spectral features of apatite. Nonetheless, HSI in the LWIR range is effective in mapping apatite and should therefore be considered as an exploration tool. This research advances our knowledge of the reflectance spectroscopy of REE-bearing minerals, which makes it easier to detect, identify, and quantify REE-bearing silicate minerals by HSI.

Feb 6, 2023

By Brian W. Mackenzie

"This paper briefly outlines the characteristics which should be considered in assessing the economics of mineral exploration, and illustrates such an assessment by using data from the Canadian base metal sector. Implications for the sector are found to include the following:(1) base metal exploration has the potential to create a substantial amount of new wealth;(2) investment incentive for exploration under current conditions is not unattractive over-all;(3) because of existing taxation policies, there is much more incentive for large companies to explore than for smaller enterprises;(4) succesful exploration is sensitive to the size, financial resources and organizational structure of the exploration entity;(5) the general level of recent exploration expenditures should be adequate to maintain the current rate of production and perhaps to support very modest growth; and(6) there is an important opportunity for growth in the sector.The findings of the study suggest that government policies should be made more flexible, in order to take into account the risks associated with exploration and with price fluctuations in the base metal sector. Recommendations are also made concerning improvements in provincial regulations for disclosure of exploration information."

Jan 1, 1981

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over the navigation channel. The subsurface soil profile was quite variable along the bridge alignment. In Virginia, there was fill over soft Alluvial deposits underlain by dense Terrace deposits, as well as remnant foundations from a former ship yard. At the bascule span, there was up to 50 ft of a soft organic silty clay layer underlain by a deep deposit of stiff Cretaceous clay. Along the Maryland approach, there were Alluvial deposits over dense Terrace deposits over stiff Cretaceous clays and dense Cretaceous sands. The variation in subsurface conditions led to the selection of alternative deep foundations that suited the specific conditions and were based on the design phase testing program, from which ultimate design capacities were determined. During construction, there were instances of unexpected pile performance, notably different than that experienced during the design phase testing, requiring changes to the contract installation criteria and re-design. This paper will present the types of deep foundations used for the project, the performance criteria assumed during the design, the measured performance and difficulties encountered during construction, and the resulting remedial actions, i.e., changes to contract installation criteria and/or re-design due to the unanticipated field conditions.

Jan 1, 2009