Search Documents

By Katsuyoshi Tatenuma

"In order to mitigate the effect of global warming by preventing the accumulation of atmospheric CO2, a permanent fixation method of surplus CO2 as an insoluble mineral onto the sea bottom is proposed. As the proposed reduction method of atmospheric CO2, the concrete concept of this method is to form an insoluble carbonate mineral (CaCO3) by direct electrolysis of the seawater; Ca2++2HCO3 -+OH- ? ?CaCO3(insoluble)+CO3 2- (soluble)+H++H2O <not as coral reef reaction>, are directly disposed of itself onto the sea bottom. By this treatment, a concentration of carbonate is reduced in the section of superficial seawater, and therefore the absorption capacity of atmospheric CO2 increases depending upon the shift of chemical carbon equilibrium between the mass of superficial seawater and the atmosphere. As no additives are required, or no secondary waste are produced, the proposed method assuming as green-orientated, has possibility to resolve fundamentally the problem of global warming in a green orientate manner.IntroductionRecently, the amount of atmospheric CO2 has been exponentially increasing and it is a main greenhouse effect gas causing the global warming [1, 2]. The concentration of atmospheric CO2 has increased more than 30% (370ppm in 2001) during only last two centuries, therefore approximately 750 Gton-C of CO2 currently exist in the atmosphere, in which 180 Gton-C of CO2 are accounted for the increment during two centuries [1, 3, 4]. In order to avoid the progressive increase of CO2 global abundance, 3 Gton-C of the incrementing amount per year [4], have to be removed annually from the atmosphere."

Jan 1, 2008

By Charles H. Jacoby

The economic importance of salt domes has been recognized throughout the world primarily because of oil and gas accumulations on their flanks and, to a lesser degree, for the value of their salt and potash. Recently they have become of value as hosts for cavities used to store hydrocarbons. In the near future we believe that their main value will be as a source of geothermal energy. Although tremendous effort has been expended on the understanding of the geology and physical characteristics of the strata intruded by salt domes, relatively little energy has been exerted in the comprehension of the salt dome itself. Salt domes have long been recognized as a geological heat anomaly. With respect to other sedimentary rocks, salt is a good conductor of heat. Expressing values in 10-3 cgs units, sedimentary rocks vary from 1.0 to 8.0; metamorphic rocks from 5.2 to 8.4 and igneous rocks from 3.1 to 9.8. Rock salt in its pure form has a thermal conductivity of 17. (Gussow, 1970). Thus a salt dome (Fig. Ml) can be expected to act as a conduit bringing heat vertically from deep within the Earth&apos;s crust. This was, in part, substantiated when in 1958 a horizontal core hole was drilled from within the Avery Island Mine at the 500 foot level. The horizontal hole was started where the ambient temperature of the salt was 74° F. and drilled toward the center of the dome. At the end of this 2,000 foot hole the temperature was 90° F. thus depicting a horizontal temperature gradient of 7° F./1,000 feet. Because this core hole penetrated a shear zone connate water that appeared as a "cold spot" on the temperature gradient, the foregoing data can only be regarded as indicative.

Jan 1, 1974

By M. M. Wong

Salt mixtures consisting of KC1, BaC12, and HfCl4 with RbCl or CsCl were investigated as electrolytes for refining hafnium. The presence of RbCI or CsCl in the electrolyte appeared to suppress the volatility of. Best electrorefining was obtained with an electrolyte containing 50.7 percent KCl, 27.l percent BaCl2, 15.7 percent CsCl, and 6.5 percent HfCl4. In this electrolyte, hafnium metal with an average oxygen content of 470 ppm was produced from an anode feed containing l,600 ppm oxygen. All metallic impurities were lowered, except titanium, manganese, and tin.

Jan 1, 1966

By Raissa Santos Salgado

Atualmente, a exigência do mercado pela produção de aços de alta qualidade aliada a redução de custos, impulsiona maiores investimentos em novas tecnologias e a busca pelo melhor conhecimento dos processos que ocorrem na usina siderúrgica. O desgaseificador RH tem-se revelado um equipamento fundamental para produção de aços ultra low carbon, tipo cada vez mais solicitado pelos maiores consumidores de aço. Diante disso, este trabalho visa a elaboração de um modelamento matemático das curvas de descarburação e desidrogenação no RH thyssenkruppCSA. A geração dessas curvas possibilitou o estudo do comportamento do teor de carbono e hidrogênio durante o tratamento das corridas no reator. Os resultados demonstram que o teor de carbono médio obtido não está dentro do esperado, conforme previsto pelo comissionamento. No entanto, a desidrogenação pode ser considerada como satisfatória.

Oct 30, 2017

By G. R. Phare

Explosives formulation is dictated by desired field performance, which in turn is dependent on such physical properties as strength, velocity of detonation, sensitivity, and water resistance. The design of explosives to obtain these properties is discussed with some reference to detonation and rock mechanics theory.

Jan 1, 1958

By R F. G Phelps

The former Gwynfynydd gold mine is located within the heart of the Snowdonia National Park, North Wales, United Kingdom. The black shale-hosted quartz reefs have intermittently produced more than 50 000 ounces of gold since 1863. Its most recent period of operation by Welsh Gold PLC was between 1992 and 1999 when it extracted 10 000 tonnes annually from a total resource base of 180 000 tonnes. A historical mining grade of 15 grammes/tonne was recovered from the Chidlaw Reef on which all production was based. Erratically distributed gold pockets hosted in the footwall zone of a 3 - 6 m wide quartz reef characterise the mineralisation. The gold exhibits a high-nugget effect and as a consequence the accurate determination of tonnage and grade was difficult. Production was undertaken by overhand shrinkage stoping. Due to its location within a National Park certain environmental constraints were placed on the operators. The principal requirement of planning permission was that processing should take place above ground and not involve chemicals. As a result, an underground mill based on physical separation methods was constructed in response to these environmental constraints. Much of the mine discharge is related to the flow of rainwater through the workings from surface openings on the reefs. Discharge from the underground milling facility was enhanced in various metals, particularly zinc, though was reduced to legally acceptable levels using liming tanks prior to discharge into the River Mawddach. The company was required to monitor and treat all water discharged from the mine before it reached the river. The mine closed in 1999, since which time a tip re-processing has continued as part of an environmental remediation and gold supply program.

Jan 1, 2002

By L. O. Howard

L. D. RICKETTS, New York, N. Y.-The advance which has been made in Smelting has been in the line of cheaper cost of handling, due to larger units and decrease in losses. At the International smelter, Mr. McGregor designed everything to handle the ore under cover. But we do find an unaccounted for loss of 0.7 per cent. of our copper, which is serious. Mr. Wallace has made a suggestion that I think metallurgists ought to know of and think about. He made it years ago-and that is that one of the chief losses is undoubtedly in the charging and discharging of the calcine cars. His idea is that possibly the dryers and heaters might be put immediately over the reverberatories So that they could discharge in conveyors. They could feed on both sides, and thereby the dust raised by discharging in the cars from the hoppers could be overcome. E. P. MATHEWSON, Anaconda, Mont.-I might Say a few words on the plants we have visited So far. I was particularly struck with the cleanliness of the plants, which is next to Godliness. I noticed also that the skull-cracker arrangement they have for handling their converter slag is very good. And they have paid considerable attention to ventilation, and are taking steps to take care of the health of the men. "Safety first" has been well looked after in all the plants we have visited so far. The steel structures are right up to date, and the buildings are of the most modern type, and everything is conveniently arranged. I think the designers of the plants in the Southwest are to be congratulated on what they have done.

Jan 12, 1916

By William E. Greenawalt

Ever since electrolytic copper refining gave promise of success, about a half century ago, efforts have been made to apply the idea to the extraction of copper from its ores. The methods of attack have, usually, been to leach with a dilute acid and then to deposit electrolytically the copper from the resulting solution with the simultaneous regeneration of the solvent used in the process. Many efforts have been made, and many patents have been taken out, both in the United States and abroad, to give this idea practical application, but only within the past few years have the difficulties been surmounted. Leaching and electrolysis, as applied to copper ores, are among the most promising fields in modern metallurgy. New conditions are arising, which will bring the wet methods into prominence; while high freight rates and increasing cost of fuel will tend to limit smelting to highly favored localities. The possibilities offered by the installation of hydroelectric plants and the greatly enlarged range of power transmission will greatly widen the field of electrolytic methods. Electrolytic methods are ideally adapted to hydroelectric development, for the load is constant throughout the full twenty-four hours, and the cost of both installation and operation of hydroelectric plants is not appreciably greater when operating for twenty-four hours than when operating for eight or ten hours; whereas, in fuel-power generation, as also in smelting, the cost is more or less in proportion to the fuel and power used. Nevertheless, fuel-power generation presents advantages in electrolytic methods, as the power plant may be located in a favorable place while the leaching and electrolytic plants may be located at the mine. The ultimate possibilities of the wet methods have yet to be determined. The possibilities of smelting have been thoroughly worked out; there is no unsolved major problem in copper smelting, and it has practically reached the limit of its possibilities. It seems hardly probable that any future improvement, either of method or apparatus, will greatly

Jan 1, 1924

By AIME AIME

AT a joint meeting of the Tulsa Geological Society and the Mid-Continent Section of the A; I. M. E., held at Tulsa on March 21, the history of unit development in the Kettle- man Hills field was discussed. Robert C. Patterson? Super- visor for the U. S. Geological Survey at Taft, Calif., was the speaker. An abstract of some of his remarks follows: On July 1, 1923, curtailment agreement for two years was made between the operators of North Dome Kettleman and the U. S. Department of the Interior. In this it was agreed to consider a plan of unit development, or other cooperate method of developing the structure. As a result, Kettleman North Dome Association was incorporated in December, 1930, as a non-profit cooperative corporation under the laws of California. Approved in January, 1931, by California Oil and Gas Supervisor and by Secretary of Interior. On Feb. 10, 1931, it became an active organization through election of executive officers and eleven- directors. General manager chosen. Association started to function April 1, 1931. Assumed control of 10,800 acres of proved and semi-proved land, as shown in Table 1.

Jan 1, 1932

By "Andreas Steinwandter

The demand for increasing energy efficiency and CO2 reduction is one of the global megatrends of our time. Although the steel industry suffers from a volatile economic environment, the steel plants are interested to find opportunities for sustainable cost reduction and put efforts into healthy solutions for the environmental. Integrated steel plants are trying to cut electrical power and energy costs as these are among the biggest cost factors that can be influenced and taking all the advantages they can. For the integrated iron and steel making route the interaction of waste energy utilization along with process energy demand, natural and metallurgical gases, steam and heating systems as well as power generation has to be considered. Potential energy sources, such as sinter plant, basic oxygen furnace (BOF) cooling stack or reheating furnaces are considered in order to elaborate an integrated energy concept. Especially electric power generation is an attractive option for steel plant operators since it can easily be connected to the existing power grid of the steel plant. When direct local use of waste heat is limited, the best option is to convert it to mechanical/electrical power with a Rankine Cycle. A stand-alone system, compact design with minimum operational costs in order to fit into the existing steel plant layout, are the main requirements of such units. The objective of this paper is to demonstrate economic feasible opportunities for energy recovery for sinter cooler and basic oxygen furnace with focus on electric power generation via ORC modules taking at the same time advantages of CO2 reduction by utilizing waste heat from the process. Furthermore typical arrangements and layouts of such solutions as well as basic economic calculations will be presented in the paper.

Oct 30, 2017

By Raymond B. Ladoo

"The talc and soapstone deposits of Vermont have been worked more or less continuously for nearly 100 years, but all of the early efforts seem to have been directed toward the production of slabs for foot warmer, and other similar uses. Altho soapstone of good quality occurs at several places, much of the material first utilized was really talc and was not massive enough to be cut successfully. The grinding of talc in Vermont seems to have commenced in about 1902 and has shown continuous growth since that time. Statistics compiled by the Geological Survey in Mineral Resources of the ,United States show that the production of talc in Vermont has increased, from 8,978 short tons valued at $65,525 in 1905 to 93,960 short tons valued at $625,150 in 1917. Until 1917, New York was the leading producer in both tonnage and value with Vermont second, but in 1917, Vermont took the lead in tonnage produced, although not in value, with a production of over 47% of the total tonnage produced in the United States and over 35% of the world's pro-duction. This increase in production will probably be continued, though possibly at decreased rate, for the reserves of talc In Vermont are large.Active talc mines and mills in Vermont are found in four districts: Chester, Windsor County; Rochester, Windsor County; Waterbury, Washington County; and Johnson, Lamoille County, These mines and mills are distributed as shown in the following table:While there are a great many other known deposits of talc and soapstone in Vermont, some of which have been worked, those listed above are the only ones which have survived and are producing on a commercial basis. The closing down of many mines and quarries, for example, those at Perkinsville, Stockbridge, Reading, Cavendish, and Athens, has been attributed to several causes. Of these causes the most important seem to be exhaustion of the deposit, poor grade, long haul to the railroad, poor management due to lack of knowledge of mining methods and failure to consider talc mining strictly as a business proposition. The companies which are now operating with greatest apparent success are those which have realized the present and future possibilities of their industry, and have invested sufficient capital in both equipment and personnel to establish their companies on a firm business basis."

Sep 1, 1919

By A. Soderberg

This paper describing the mining practice at the Utah Copper Co., Bingham Canyon, Utah, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Utah Copper Co. operates the low-grade open-out copper mine at Bingham Canyon, Utah, which is 30 miles in a southwesterly direction from Salt Lake City. In addition to the mine the company operates two flotation concentrators, the Magma plant and the Arthur plant, which have a combined capacity at maximum metallurgical efficiency of 60,000 tons daily. The concentrators are at Magna, about 18 miles from the mine. The company operates its own standard-gage railway, known as the Bingham and Garfield Railway, between the mine and the mills (fig. 1). Concentrates are smelted at the Garfield smelter of the American Smelting and Refining Co., situated 4 miles from the mills.

Jan 1, 1930

By Harry W. Campbell

In 1984 and 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the Meadow Valley Range Wilderness Study Area (NV-050-156) in order to evaluate its identified mineral resources. The study area is located in Clark and Lincoln Counties, NV, about 50 miles northeast of Las Vegas, NV. The Johnston and Fitchett prospect, in the northern part of the study area, has more than 3 million tons of marginal perlite reserves suitable for many commercial uses. A preliminary mining feasibility estimate suggests perlite could be profitably mined from the study area; however, it is unlikely these perlite deposits will be developed in the foreseeable future because of unfavorable market conditions. Zeolite minerals occur in alteration zones adjacent to perlite deposits at the Johnston and Fitchett prospect, but high quality material is closer to potential markets. A metalliferous black shale unit containing 800,000 tons of subeconomic resources may extend into the study area at the Bradshaw vanadium prospect on the northwest boundary. Limestone, stone, sand, and gravel occurrences are wide-spread, but other suitable deposits in the region are more accessible to potential markets. Seven prospects in and near the study area were examined. The entire study area is leased for oil and gas exploration. A group of perlite placer claims covering more than 480 acres was located in the 1940&apos;s in the northern part of the study area. A small group of lode claims was located in the mid 1950&apos;s in the southwest part of the study area. No mining claims are currently (1985) held inside the study area. No mineral production is known from within the study area.

Jan 1, 1987

By R. Karl Zipf, Z. T. Bieniawski

"Researchers at The Pennsylvania State University are engaged in a project to understand the mechanics of respirable size fragment formation in coal. The project is based on the premise that a thorough understanding of the fundamental mechanics of fine fragment formation may lead to techniques for reduction and better control of coal dust problems in mines. Presently, it is believed that the mode of fracture propagation which can range from pure tensile to pure shear or any mixed mode in between and the loading or displacement rate can influence the amount of respirable size fragments that are generated on new fracture surfaces during the fracture propagation process The essence of any coal cutting process is one of mixed mode fracture propagation. To study the crack propagation process, a unique mixed mode testing rig was designed and fabricated. This rig is capable of applying loads to a prenotched test specimen that range from pure Mode I (tensile mode) to nearly pure Mode II (shear mode) or many mixed mode loading combinations. It is also possible to apply different loading or displacement rates to the test specimen. With this rig, it is possible to create new fracture surfaces via the different fracture modes and under various loading conditions.These new fracture surfaces are examined with a scanning electron microscope (SEM) to characterize the amount of structural damage and respirable size fragment formation that occurs during the fracture process. Initial observations suggest that the amount of fine fragment formation and the new fracture surface appearance is related to the fracture initiation conditions, particularly the fracture mode and the loading rate. Mode II loading and higher loading rates seem to generate more structural damage and respirable size fragment formation that Mode 1 loading at slower rates.With the mixed mode test rig, the mechanics of fracture initiation for a single crack can be controlled to better understand its influence on respirable size fragment formation. Such understanding may lead to methods which characterize the tendency of specific coal seams to produce undesirable fine fragments during the fracture process, or it may lead to rational recommendations and design guidelines or coal mining machines which inherently produce less dust.IntroductionAs part of a larger effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners, researchers at The Pennsylvania State University are engaged in a project to understand the fundamental mechanics of fine fragment formation in coal. This project is part of a com¬prehensive research effort within the Generic Mineral Technology Center for Respirable Dust which is jointly administered by The Pennsylvania State University and West Virginia University.The principal source of the coal dust in underground mining is the cutting operation. The U.S. Bureau of Mines (USBM) and various European research organizations have conducted investigations into the mechanics of coal cutting for many years. These studies of airborne respirable dust (ARD) formation have concentrated on empirical studies of the various cutting parameters and their effect on ARD for¬mation. The parameters study include depth of cut, cutting speed and bit spacing.(1,2) Other studies investigated the effect of symmetric and asymmetric bit wear and various bit geometries and designs (3-5) Roepke(6) summarized the principals of proper coal cutting to minimize dust formation by recommending to ""cut at maximum depth (maximum advance rate) at all times, at minimum RPM, with the fewest possible bits, having the lowest possible included tip angle."" Most coal in the U.S. is mined with the continuous mining machine which inherently cannot meet these design recommendations.(3)It is recognized that respirable size dust particles are formed and/or liberated by a fracture process. One extremely interesting and useful study performed very early in the USBM dust re"

Mar 1, 1989

By S. Rideout

As Assistant Director for Program Support for the Office of Surface Mining Reclamation and Enforcement (OSM), a bureau of the U.S. Department of the Interior, I am responsible for the regulatory and abandoned mine land programs under the Surface Mining Control and Reclamation Act of 1977, which governs the environmental impacts of coal mining. My perspective is influenced by my current position and my previous positions in government and private industry. Sustainability is a cooperative effort of many parties and can only be achieved if each assumes their responsibilities for making it happen. I will highlight some of my thoughts on the role of government in achieving sustainability in the mining arena.

Jan 1, 2007

By M. A. Wei

Effects due to some metal cations, such as Ca2+, Mg2+,Fe2+, Fe3+, Cu+, Cu2+, Zn2+ and Al3+ etc., which are produced in the pulp when the complicated ore is dipped in the deioned water, on the flotation of chalcopyrite and galena with the isopropyl thionocarbamate as collector have been studied. It is found that chalcopyrite floatability is not influenced by these cations, and the cations can be di-vided into three types according to their effects on the purified galena?s floatability with the same conditions, as activator such as Cu+; as depressant such as Al3+, Fe3+, Fe2+, Zn2+ and Cu2+ , unaffective such as Mg2+ and Ca2+.

Jan 1, 2014

By D. H. Carlson, J. H. Johnson

"The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios.The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory grade instruments. Concentrations of CO and C02 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for C02• EMA measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and C02 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios."

Mar 1, 1992

By J J. Pretorius, G M. Hoffmann

Utilisation of lower-grade (<60 per cent Fe) resources, not utilised in the current products, is crucial to ensure optimal resource utilisation and maintaining/improving future profit margins by reclassifying low-grade material to ore. The purpose of the Sishen Expansion Project (?SEP?) is therefore to investigate the technical and financial viability of producing up to an additional 10 Mtpa of new products at Sishen from material currently classified as low-grade materials. Jigging technology has progressed to a point where Sishen?s 50 to 60 per cent Fe run of mine (?ROM?) material, once considered as waste, can be beneficiated to produce a saleable 64 per cent Fe product. This has been confirmed through appropriate beneficiation testwork. Consequently, Sishen can now produce saleable product from material not currently included in the resource definition, increasing the resource base of the mine significantly and ensuring higher resource utilisation. Mine Planning utilised the geological models to produce detail planning schedules, reflecting the current and SEP plants separately, optimised to comply with product specifications of both the current and SEP plants and to confirm the viability of the low-grade resources identified as SEP feed material. The SEP products specifications have been derived by optimally matching iron ore market requirements with the revised resource base. A 64.0 per cent Fe lump product and a 63.5 per cent Fe fine product are the optimal SEP products. The SEP plant will be able to produce 10Mtpa at an average yield of 60 per cent and a lump to fine ratio of 62 to 38. The plant consists of five major sections namely crushing, material preparation, beneficiation, final product handling and quality control services. Maximum integration with the current Sishen plant was considered. Kumba currently has an agreement with Transnet to rail up to 23.5 Mtpa through the Sishen Saldanha Iron Ore Export Channel (?IOEC?). Transnet and Sishen Iron Ore Company have signed a Definitive Agreement that deals with the expansion of IOEC?s capacity, which increases Kumba?s entitlement from 23.5Mtpa to 35.0Mtpa. The detailed enviro-legal impact assessments for the SEP indicated that the project has low enviro-legal risk as a result of it being a brownfields project incorporated into the current Sishen operations.

Jan 1, 2006

By John T. Galey

Production of crude oil for 1940 in southwestern Pennsylvania was off nearly 70,000 bbl., largely as a result of the great number oi abandonments, together with the lack of extension of the Washington and Green County pools. Oil wells completed numbered 51, which is 26 more than last year, but the total initial production of 259 bbl. is only 18 bbl. greater than in 1939. There was an increase of 72 over last year for a total of 209f gas wells. However, 68 7 dry holes were drilled, which is 40 more than a year ago. Thus, 328f wells were drilled during the year, and rigs are erected or drilling is progressing on 59 t more. Shallow Development Oil.—Butler County led in number of oil wells completed, with a total of 27 for an initial production of only 69 bbl. Washington County, with 12 new oil wells, one of which made 40 bbl. from the Fifth sand in S. Franklin township, has 95 bbl., while in Allegheny County 9 wells gave an initial of 86 bbl. for the highest Per well average in the area. This initial was given a considerable boost by one 35-bbl and another 2;-bbl. well in West Deer township, where the Fourth sand produced at 1840 feet. Greene County had only one oil well completed during 1940, and Washington County had 12. The subnormal totals for these counties may be explained by the higher cost of completions and the declining price of crude. The first price change in crude during the year occurred on May 22, when a 25 cut was made. A second 25 cut was made July 12, and was followed by a 156 cut on .Aug. 28. This price held until Nov. 12, when there was a restoration of 156. On Dec. 17 a second 156 increase was put into effect, bringing the price to $I.So per barrel. Gas The large increase in the number of gas wells completed may be attributed to three factors; namely, the recently discovered production possibilities of moderately deep, hitherto little tested horizons, together with increased demand and price. The latter has been made possible by a recent decision of the court, which ruled restraining the public service Commision&apos;s prohibition of a raise in the minimum monthly charge to small consumers by one of the major gas companies. A portion of the revenue derived in this manner is being passed along to the producer in the form of higher prices in the field. This higher field rate will remain in effect until a new ruling is made, when it will be reduced in proportion to the reduction of the monthly minimum charge. In an effort to extend the chambers Dam Fifth sand oil pool southwest from Amwell township, Washington County, several wells have been drilled. One of these, in Morris township, washington County, had an initial of 3.2 million cu. ft. open flow from the Big Injun sand. This indicates an entirely new productive area for the latter horizon. Allegheny County had one spectacular well in South Fayette township-—at a depth of about 2500 ft. a 4-million-CU. ft.

Jan 1, 1941

By John T. Galey

Production of crude oil for 1940 in southwestern Pennsylvania was off nearly 70,000 bbl., largely as a result of the great number oi abandonments, together with the lack of extension of the Washington and Green County pools. Oil wells completed numbered 51, which is 26 more than last year, but the total initial production of 259 bbl. is only 18 bbl. greater than in 1939. There was an increase of 72 over last year for a total of 209f gas wells. However, 68 7 dry holes were drilled, which is 40 more than a year ago. Thus, 328f wells were drilled during the year, and rigs are erected or drilling is progressing on 59 t more. Shallow Development Oil.—Butler County led in number of oil wells completed, with a total of 27 for an initial production of only 69 bbl. Washington County, with 12 new oil wells, one of which made 40 bbl. from the Fifth sand in S. Franklin township, has 95 bbl., while in Allegheny County 9 wells gave an initial of 86 bbl. for the highest Per well average in the area. This initial was given a considerable boost by one 35-bbl and another 2;-bbl. well in West Deer township, where the Fourth sand produced at 1840 feet. Greene County had only one oil well completed during 1940, and Washington County had 12. The subnormal totals for these counties may be explained by the higher cost of completions and the declining price of crude. The first price change in crude during the year occurred on May 22, when a 25 cut was made. A second 25 cut was made July 12, and was followed by a 156 cut on .Aug. 28. This price held until Nov. 12, when there was a restoration of 156. On Dec. 17 a second 156 increase was put into effect, bringing the price to $I.So per barrel. Gas The large increase in the number of gas wells completed may be attributed to three factors; namely, the recently discovered production possibilities of moderately deep, hitherto little tested horizons, together with increased demand and price. The latter has been made possible by a recent decision of the court, which ruled restraining the public service Commision&apos;s prohibition of a raise in the minimum monthly charge to small consumers by one of the major gas companies. A portion of the revenue derived in this manner is being passed along to the producer in the form of higher prices in the field. This higher field rate will remain in effect until a new ruling is made, when it will be reduced in proportion to the reduction of the monthly minimum charge. In an effort to extend the chambers Dam Fifth sand oil pool southwest from Amwell township, Washington County, several wells have been drilled. One of these, in Morris township, washington County, had an initial of 3.2 million cu. ft. open flow from the Big Injun sand. This indicates an entirely new productive area for the latter horizon. Allegheny County had one spectacular well in South Fayette township-—at a depth of about 2500 ft. a 4-million-CU. ft.

Jan 1, 1941