Search Documents

By R. J. Leary

The natural gas-air burner described in this report was designed and constructed to meet the thermal requirements of a convective process for heating steel scrap. This process involved downward combustion of natural gas with air, blending the combustion products with diluent air, and then passing this tempered stream of gases downward through a porous bed of steel scrap contained in the furnace chamber. The scrap would be heated to a temperature limited by the adiabatic flame temperature of the gas stream in a period that depended on the rate at which heat was supplied per unit of bed cross section. The temperature of the gas stream would be limited to that beyond which an objectionable degree of oxidation would occur; for carbon steel this limit had been found to vary from 1,900° to 2,100° F. with the superficial velocity of the gas stream. The productivity of the process was dependent on the rate of heat input per unit of furnace cross section; for the 3-foot-diameter experimental furnace an input of 680,000 B.t.u. per hour was desired. The burner described was designed to meet these conditions of temperature and heat input. It provided for three streams of entering gases: (1) A primary air-fuel mixture too rich to be combustible, that is, above the upper flammable limit; (2) secondary air for combustion of the primary mixture; and (3) tertiary air, principally for cooling the combustion products to the temperatures desired for process operation. Downward combustion of the primary and secondary streams occurred in a flame stabilized on an annular port, while tertiary air flowed in an annular path surrounding the port and also through an axial channel whose wall formed the inner ring of the annular port. This burner performed beyond the designed heat-input rates while producing stable flames, which were adjusted readily to the temperatures desired. Gas-stream temperatures were easily controlled to within 15° F. of the desired value by simple manual adjustment of the flow valves.

Jan 1, 1959

By George A. Komadina

Pima Mining Company has recently completed their expansion tripling the plant capacity to 18,000 tons per day and now is in the process off expanding to 30,000 tons per day with completion scheduled for the summer of 1967. This paper briefly discusses the additions to the mining department and support areas with a more detailed report on the complete new crushing plant and additions to the concentrator. The crushing plant includes a 54-inch gyratory crusher, three 7-foot standard and seven 7-foot short head crushers along with necessary screens, feeders, and conveyor belts to produce a minus 1/2-inch rod mill feed. The concentrator consists of ten milling sections, each containing one 10-foot by 16-foot rod and two 10.5-foot by 13-foot ball mills, classification is done with cyclones. Pulp from each section is floated in 50 cells of 66-inch Fagergren flotation machines to produce a rougher concentrate which is cleaned in six stages of Denver cleaners to produce a final concentrate The various mill products are thickened with disposal made in conventional manner. Plant instrumentation is discussed in the paper.

Jan 1, 1967

By B. P. Watson, D. Hoffmann, D. P. Roberts

Potholes on the Merensky and UG2 reefs in the Bushveld Complex occur as near-circular to elliptical depressions or slumps on the reef horizon, normally presenting as severe disruptions which prevent economic extraction. Within the pothole, the reef and other strata may either be attenuated, absent, or highly deformed, this being the result of the overlying hangingwall strata having slumped down. The hypotheses for pothole formation involve several mechanisms, including downward erosion, upward fluid movement, or synmagmatic deformation. When potholes are exposed in mine workings, significant fracturing is often observed. This fracturing is particularly evident in anorthosite rock types. Stress measurements were conducted in a pothole on the Merensky Reef to determine if the fracturing was due to high stress conditions. The paper describes the measurement results and numerical modelling that was done to determine the influence of depth and mining on the stress condition at the site. The results show that high stresses do exist in at least some potholes, and that current formation theories do not adequately explain the measured stresses. In support of understanding the high local stress associated with the pothole, the study explored several rock engineering modelling processes to validate the conditions of the study site and enclosing excavations. A better understanding of the stress conditions in potholes with additional data could lead to more appropriate support design and avoidance of potential rockbursts in these structures.

Jan 1, 2021

By Wallace W. Roepke

The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60' and 90' (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate.

Jan 1, 1983

By J. E. Brantly

In October 1939, a drilling program was commenced on the Atlantic seaboard of Brazil, with three steam rotary rigs of medium capacity. One of these was assigned to the State of Alagbas and the other two to the State of Bahia. During the remaining few months of 1939 and during the year 1940, some eight wells were drilled, two in Alagbas and six in Bahia. Two small producers were found in the latter state. In early 1941 three medium-weight Diesel rigs were added to the equipment, thus permitting the drilling of some 15 wells during the year 1941. The two small producers found in 1940 in the State of Rahia were near the city of Silo Salvador. In 1941 three additional small wells were brought in, in the same area, and a further producer on an isolated structure some 75 km. to the northwest of this production. No commercial production has been found in the State of Alagbas. Approximately 26 wells have been drilled or are drilling, six of which are producers— five in one area and one in another. The program for 1942 calls for the development of the two areas in which wells have been found and also the drilling of several wildcat structures located either by geophysics or surface geology. All production in the area of the several producing wells is somewhat less than 2000 ft. and in the other area about 3800 ft. The area of the several wells is known as the Lobato field, and is practically within the city limits of Sao Salvador. The area 75 km. northwest of the city will be known as the Candeias field.

Jan 1, 1942

By J. E. Brantly

In October 1939, a drilling program was commenced on the Atlantic seaboard of Brazil, with three steam rotary rigs of medium capacity. One of these was assigned to the State of Alagbas and the other two to the State of Bahia. During the remaining few months of 1939 and during the year 1940, some eight wells were drilled, two in Alagbas and six in Bahia. Two small producers were found in the latter state. In early 1941 three medium-weight Diesel rigs were added to the equipment, thus permitting the drilling of some 15 wells during the year 1941. The two small producers found in 1940 in the State of Rahia were near the city of Silo Salvador. In 1941 three additional small wells were brought in, in the same area, and a further producer on an isolated structure some 75 km. to the northwest of this production. No commercial production has been found in the State of Alagbas. Approximately 26 wells have been drilled or are drilling, six of which are producers— five in one area and one in another. The program for 1942 calls for the development of the two areas in which wells have been found and also the drilling of several wildcat structures located either by geophysics or surface geology. All production in the area of the several producing wells is somewhat less than 2000 ft. and in the other area about 3800 ft. The area of the several wells is known as the Lobato field, and is practically within the city limits of Sao Salvador. The area 75 km. northwest of the city will be known as the Candeias field.

Jan 1, 1942

By A. K. Snelgrove

At a time when water resource planning is proceeding on a continental scale, such as the proposed $100 billion North American Water and Power Alliance, which would redistribute water among three nations, including seven provinces of Canada, 35 of the United States, and three States of Mexico, the selection of a single river basin for study may seem to require an apologia. None is offered because of ( 1) the magnitude of the Indus , itself a part of the great Indo-Gangetic Plain drainage system, with Himalayan sources, upon which the thickly populated northern sub-continent of Indo-Pakistan depends for agriculture and hydroelectic power; (2) the extraordinary problems created by dismemberment of the world?s largest irrigation system through legal beheading of the Eastern Waters under the Indus Waters Treaty of 1960; and (3) the herculean effort to contain the twin encroachments of waterlogging and salinization in a basin which faces a shortage of fresh water. The British irrigation system of barrages and canals on the Indus was a venture admirable in conception. Unfortunately, it is now a legacy burdened with unwanted consequences, due to interference with the hydrological regimen, particularly the rise of water table occasioned by leakage.

Jan 1, 1967

By R. Khanna, K. Hyun Ko, A. J. Berkovich, J. Hook

"The co-pyrolysis of synthetic polymer polyethylene terephthalate (PET) and agricultural wastes (naturally occurring polymer-macadamia nut shell) was investigated in the temperature range 473K to 1273K using a horizontal furnace with an aim to understand their thermal degradation under isothermal conditions. In-depth characterization of pyrolysis residues was carried out using x-ray diffraction (XRD) and solid state nuclear magnetic resonance (NMR) for carbon structure, and through determination of the concentration of unpaired electrons using electron paramagnetic resonance (EPR). In previous studies, it has been found that PET thermally decomposes ~ 650K-700K, releasing (~80 wt % of initial weight) gaseous products due to random chain scission. In the case of macadamia nut shell, three types of byproduct can be obtained from pyrolysis: char, tar and gaseous products. In the co-pyrolysis of macadamia nut shell with PET in 50-50 wt% ratio, total product weight ratio could be modified with the addition of PET acting as a hydrogen source. This is because a recombination of thermal cracking products of cellulose could be suppressed by hydrogen from PET, which will later lead to an enhancement of tar formation. In addition, pyrolysis around 673K is sufficient for bond cleavage to occur in cellulose and lignin leading to the formation of negatively charged activated carbon with high surface area, providing bonding sites for volatiles evolving from PET. Therefore the co-pyrolysis may be able to enhance the product yield (tar/char/solid carbon residue) along with a reduction in the release of gaseous products. During the co-pyrolysis, temperature was found to have a significant influence on the kinetics of thermal degradation and solid residual by-products after co-pyrolysis.INTRODUCTIONPlastics are being used worldwide in a wide range of applications in the modern society; their usage has resulted in increasingly a massive waste problem. The production of most synthetic plastics requires hydrocarbons that are produced from petrochemicals derived from fossil oil and natural gas, a non-renewable source (Speight 2011). Currently, plastic manufacture utilizes ~4% of world oil and gas production, and it is expected to drive further increases in petroleum demand by 1-2% due to their large volume of manufacture (Hopewell, Dvorak et al. 2009). Landfilling and incineration of plastic waste are the two main routes to plastic waste management (Encinar and González 2008). In Australia, only 10% of waste plastics were recycled in 2006 (White and Hyde 2011). This means that large amount of fossil fuels from plastics has either been simply burned for energy recovery or buried in the ground. There is an urgent need for developing alternative avenues for recycling waste plastics. Our group at UNSW has carried out extensive research on the recycling of waste polymers as carbon resource in steelmaking including slag foaming and carbon dissolution from waste plastics into liquid steel at 1600°C; the effect of basic plastic characteristics such as chemical composition, structure, bonding network etc. was examined (Sahajwalla, Rahman et al. 2009)"

Jan 1, 2012

By L. C. Lang

INTRODUCTION The introduction of 165-mm (61/z-in.) holes to underground mining operations has made possible the application of Canadian Industries Ltd's (CIL) vertical crater retreat (VCR) mining method, illustrated in the accompanying sketches. This unique and revolutionary new application of spherical charge technology (see the Appendix), when applied to primary stopes and pillar recovery, eliminates raise boring, slot cutting, and dilu¬tion of ore by backfill; greatly improves fragmentation; reduces labor and time requirements; eliminates uphole drilling and blasting; and minimizes or completely elimi¬nates damages by blasts to the walls and retreating backs of the stope or pillar. If vertical large diameter holes are drilled on a designed pattern from a cut over a stope or pillar to bottom in the back of the undercut, and spherical charges of explosives are placed within these holes at the calculated optimum distance from the back of the undercut and detonated, a vertical thickness of ore will be blasted downwards into the previously mined area. Repeating this loading and blasting procedure, min¬ing of the stope or pillar retreats in the form of horizontal slices in a vertical upwards direction until the top sill is blasted and the mining of a stope or pillar is completed. The VCR method is also applicable to drop raises and has the potential to replace all other raising methods under most circumstances. PILLAR RECOVERY Levack Mine Inco Metals Co., Ontario Div., provided the first opportunity for the method in pillar recovery. The Levack mine's high grade ore pillar No. 4800 on the 975-m (3200-ft) level was used for the production¬scale experiment (Figs. 1 to 3). The pillar was about 49 m (160 ft) long, 6 m (20 ft) wide, and 20 to 26 m (65 to 85 ft) high. The mined area on both sides of the pillar was backfilled with a 1:30 cement:sand mixture. The pillar was removed in two phases. In phase 1, the standard uphole method was used to blast down the 18-m (60-ft) long section of waste from the bottom of the ore into the undercut. From the pillar's top sill, 165-mm (61/a-in.) holes were drilled downward into the pillar, and by measuring the depth of the holes, the results of the uphole blast were determined and roof line 1 was established. The bottom of each hole was plugged, then filled with sand to place the center of gravity of each spherical charge (loaded from the top sill) at a predetermined optimum distance from the horizontal free surface. The charges were then detonated. After detonation, both draw drifts were full of extremely well-broken material. The depth of each hole was measured again, and the plot of these depths re¬sulted in roof line 2. The same blasting procedure was repeated and the resultant new back elevation was marked by roof line 3. The poor results of the initial uphole blast at one location (notice the peak in area 1) appeared to influ¬ence the subsequent new backs. A third blast success¬fully evened the back, and resulted in roof line 4. An unblasted slab averaging 6.3 m (20.9 ft) thick remained below the pillar's top elevation as the final sill. In all three spherical charge blasts fragmentation of the blasted material was extremely fine. The backfill was fully exposed on both sides of the now-blasted pillar. The backfill remained undamaged and the ore was not diluted by sand. The remnants of all the 165-mm (61/2 -in.) holes remained clean and undamaged, and the holes had well-defined bottoms that could be easily measured and plugged. Each blast took down a 3.9 to 4.2-m (13 to 14-ft) thick horizontal slab of ore. Productivity was three times greater than that of the previously practiced cut-and-fill method. Since this was the first such experiment, blasting the remaining 6-m (20-ft) thick final slab was the sub¬ject of some deliberation. If the described method was repeated, we could have ended up with a 1.8-m (6-ft) thick sill unsafe to work on. It was therefore decided to blast the whole sill using two spherical charges prop¬erly placed in each hole, but with the application of

Jan 1, 1982

By Geoffrey G. Huggins

Discussions are presented of the three phases of the noise reduction program on flight-type coal conveyors. The three phases are identification of noise sources, evaluation of potential noise reduction concepts, and implementation of noise reduction which is intended to reduce conveyor noise to less than 90 dB(A) in the underground mining environment. The major noise sources are impacts of the chain on the tail roller and on the top and bottom decks. A total noise reduction of 11 dB(A) was achieved by using techniques which are applicable to retrofit. These are a vibration isolated tail roller and an isolated wear strip on the return deck. A theoretical model of isolation provided by the isolated tail roller is developed. Appendices are presented which contain information on other potential concepts and additional data generated.

Jan 1, 1976

By Shields H. Arup

The paper describes the innovative foundation reuse and strengthening works for two buildings in Central London. A 1950s building on piled foundations (65 Whitfield St) and a 1930s building (67-69 Whitfield St) on 3m deep pad foundations were both extended upwards by two new stories. The Client for the project is Derwent London, with Make as their architect, Main Contractor Multiplex and Engineer Arup. Little was known about the foundations of either building at the start of the scheme. Extensive investigations of the existing foundations and ground conditions were carried out in both buildings. At 65 Whitfield St, investigations identified piled foundations, but found that pile lengths were short and variable. As a result, strengthening works solutions were adopted whereby the increase in column load was shed into new mini piles constructed around the existing pile caps. At 67-69 Whitfield St, deep pits were used to investigate the foundations and reuse was justified based on understanding of the pad dimensions, concrete strength, and strength and stiffness of the underlying geology. For both buildings the residual risk was closed out through monitoring during construction. The combined reuse of the structural frame and foundations of both buildings facilitated a sustainable solution, breathing a new lease of life into outdated buildings.

May 1, 2022

By K Edwards, A J. J Mouton

Hematite represents the vast majority of iron ore exported from Australia as the development and processing cost of magnetite is generally seen as a barrier to the development of vast magnetite resources. However, a number of magnetite projects have attracted a significant amount of interest and investment from large Chinese steelmakers.This paper compares the relative merits of the development of Australian magnetite and hematite ore from the point of view of the steelmaker, taking into account the factors that influence the capital costs of the development of the ore types and the relative costs of operating the process plants to treat these ores. By modelling the relative operating cost for the production of hot rolled coil in China for the two ore categories, the paper demonstrates the economic drivers behind the Chinese steelmakers’ large investments in the magnetite resources of Western Australia. It does this by estimating the potential value of magnetite concentrate to the steelmaker in the event that the maximum potential is realised by operating the blast furnace with a 100 per cent pellet burden.Under the conditions described, it was found that direct reduction (DR)-grade magnetite concentrate could command a price premium over 62 per cent Fe fines of up to 46 per cent (December 2014 on a cost and freight (CFR) basis). The corresponding premium for blast furnace (BF)-grade magnetite concentrate is 17 per cent, which demonstrates the dependency on grade.The capital expenses for a 14 Mt/a concentrate plant is estimated at US$3.1 B for BF-grade magnetite and US$3.35 B for DR-grade, with operating expenses at US$45 and US$50 respectively. The corresponding free on board price for a break-even net present value is calculated at US$82/t for BF-grade magnetite and US$90/t for DR-grade. The minimum long-term iron ore price (62 per cent Fe) that would be required to underpin such a project is estimated at US$78/t CFR for BF-grade magnetite and US$68/t CFR for DR-grade concentrate.Apart from the financial benefits, it is demonstrated that the use of magnetite concentrate in ironmaking has the potential to reduce CO2 emissions by approximately 400 kg per tonne of hot rolled coil.CITATION:Mouton, A J J and Edwards, K, 2015. Magnetite – a higher-grade blast furnace feed and its potential benefits for the ironmaker, in Proceedings Iron Ore 2015, pp 613–620 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By V. N. Mackiw, H. Veltman

"A process is described which permits the separate recovery of lead and zinc from complex low-grade sulphide concentrates such as are produced from the New Brunswick type of disseminated pyrite ores. This process calls for the preparation of a lead-zinc bulk concentrate from the original ore by flotation. The bulk concentrate is then oxidized under pressure in autoclaves in aqueous sulphuric acid solution, such as return electrolyte from zinc electrolysis. This yields a zinc sulphate solution and a residue containing lead sulphate, unaltered pyrite and elemental sulphur generated during the oxidation. After the oxidation, the leach slurry is briefly heated to above the melting point of elemental sulphur and then cooled. Thus, pellets containing pyrite and elemental sulphur are formed, and they are separated from the lead sulphate by screening and/or flotation. Laboratory tests have shown that about 95 per cent of the zinc and lead can be separately recovered from complex bulk concentrates. Process possibilities are discussed."

Jan 1, 1967

By Joseph M. Singer

Ignition of hybrid coal dust - methane - air mixtures by hot- turbulent - pulsedgas jets was investigated . The turbulent jets were generated by explosions in a primary chamber of stoichiometric mixtures of methane , oxygen , and nitrogen . The hot - gas ignition apparatus provided an adjunct means of testing , on a small scale , the type of ignition that exists in large - scale galleries or in coal mines . = coal particle The temperature Ignition variables were channel diameter , channel length , size , fuel concentration , and temperature of the hot - gas jet . of the hot jet was varied by changing the oxygen indices ( OI ) of the primary explosion mixtures . Coal dust having approximately 37 percent volatile matter was used . 02 O2ટ + N₂ The hybrid coal dust - methane - air mixtures required higher jet temperatures ( higher oxygen indices ) for ignition than the single fuel component methane - air mixtures . Methane in air concentrations less than the lower flammable limit of methane could be ignited in the presence of coal dust if the jet temperatures were increased . A specific explosion transmission ( ignitability ) curve existed for each coal dust concentration . The total fuel concentrations at the lower limit of each ignition curve was always close to or greater than stoichiometric , indicating that not all the coal dust was involved in the ignition .

Jan 1, 1964

By D. H. C. Wilton, W. A. Sears

"Abstract-The 682.8 ± 1.6 Ma Tickle Point Group consists mainly of rhyolite flows and tuffs with- in the Avalon Zone of the Appalachian Orogen in Newfoundland. Stratabound massive sulfide mineralization, consisting of pyrite, sphalerite, chalcopyrite and galena, occurs at the Winter Hill prospect, where a lower pyritic, Cu-rich zone and an upper Zn-Pb-rich zone are hosted by a carbonate-calc-silicate lens. At the Frenchman Head prospect, stringers of pyrite, minor sphalerite, chalcopyrite and rare galena are hosted by felsic volcanic rocks of the Tickle Point Group .Base metal ratios, metal zonations and the overall stratigraphic framework suggest that these sulfide occurrences represent volcanogenic massive to semi-massive sulfide mineralization (stringer type at Frenchman Head). As such these prospects represent the only known VMS occurrences within the Avalon Zone of Newfoundland. Pb isotope data indicate that galena from the Winter Hill prospect is less radiogenic and older than galena from Dunnage Zone occurrences, and suggest that the Winter Hill mineralization formed in an environment tectonically distinct (exotic) from the Dunnage Zone."

Jan 1, 1996

This problem is seen as being central to a number of peripheral problems. Of these, the following are considered to be of major importance: 1. Reserves. Changes in Quality. Depths at which they occur. The effects of catchment and water storage areas. The effects of urban development. 2. Environment and the compat- ibility of mining and preparation of coal. 3. Transportation of Coal. J. tabour.

Jan 1, 1976

This brief resume of events, transpiring in Mexico, culled front the daily New York newspapers, since the last Bulletin-went to press, does not indicate any degree of improvement in the situation. RECORDS OF 217 MEXICO KILLINGS SUBMITTED BY AMBASSADOR FLETCHER Henry P. Fletcher, the American Ambassador to Mexico, called as the first witness before the Rules Committee of the House which has begun a preliminary inquiry into conditions in Mexico, which, it, is believed, will lead to a thorough and far-reaching investigation by a joint Senate and House Committee of the entire Mexican problem, submitted a list of the names of Americans officially known to have been killed in Mexico, a majority of them murdered in cold blood, since the overthrow of Porfirio Diaz by Maderoin 1911. The list contains 217 names and in comparatively few instances do the records show that arrests were made by the particular Mexican faction that happened to be in power where the crime was committed. In only one instance, that of John B. McManus, who was killed in March, 1915, was reparation made. It is significant that McManus was killed by Zapatistas, and Zapata officials apologized for the crime and paid to Mrs. McManus a voluntary indemnity of $20,000 in gold. Of the 217 persons listed as victims of the Mexicans, .137 perished since Carranza came into power. The list, it was admitted, is not complete. It was evident, says the New York Times, that the Ambassador considered the situation very serious.

Jan 9, 1919

By John D. Bardill

This report covers the magnetic surveying done in the Plattsburg area , which was part of a general survey, of magnetite deposits in New York State . Other areas being surveyed are the Star Lake district , St. Lawrence County ; Brewster district , Putnam County; and the Sterling district , Orange County. Reconnaissance indicated an area about 3 miles long and 1,200 feet wide , but detailed surveys have been completed on only a portion of that area . In several districts , surveys of this type have served as a basis in the selection of areas for exploration by diamond drilling by the Bureau of Mines .

Jan 1, 1947

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

In underground continuous mining operations, ventilation, water sprays and machine-mounted flooded-bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements — such as face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation and equipment operator positioning — can have impacts on the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Pittsburgh Mining Research Division for remotecontrolled continuous mining machine operators as well as haulage operators at 10 U.S. underground mines. The results of these respirable dust surveys show that continuous miner exposures varied little with depth of cut but are significantly higher with exhaust ventilation. Haulage operators experienced elevated concentrations with blowing face ventilation. Elevated dust concentrations were observed for both continuous miner operators and haulage operators when working in crosscuts driven into or counter to the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposures attributable to particular mining configurations. These findings form the basis for recommendations for lowering face worker respirable dust exposures.

Jan 1, 2016

By P. J. Coleman

Research in the field of mining safety and health in the United States plays an important part in protecting the lives of miners. The National Institute for Occupational Safety and Health (NIOSH) Mining Program conducts surveillance, studies and developmental work aimed at improving the safety and health of miners. With recent reviews of the Mining Program by the National Academy of Sciences and the Mining Program response (NIOSH, 2008), the importance of setting goals, conducting high quality engineering and scientific research and evaluating the outputs, outcomes, relevance and impacts of these projects has been reemphasized. Surveillance of reported injuries is a first step in deciding on research directions and in designing specific projects. Groups of injuries often share features and attributes that suggest common causes and may respond to similar preventive efforts. Identifying groups of injuries also serves to prioritize intervention efforts. The Mine Safety and Health Administration (MSHA) Accident and Injury database (MSHA, 2008) provides individual case reports of mining injuries, illnesses and certain no-injury accidents (events such as roof falls that stop mine production or miners? activities for more than one hour). This database is an indispensable resource for researchers and stakeholders needing information on the statistics of these events. From an epidemiological perspective, research projects target groups of miners at risk due to specific patterns of work, equipment, mine settings and the management of safety and health in their mines. Incidence rates are provided by the MSHA data for selected variables, such as surface/underground location, standard industrial classification and state. While incidence rates are the preferred measure for all variables, denominators are not typically available; for example, to more clearly under-stand the data about injury by occupational type, it would be necessary to conduct demographic surveys. A current survey of the demographics of the mining industry should be complete by 2010, which will allow incidence rates to be developed for a number of variables such as age, occupation and experience. This survey will provide the first update of its kind since the first survey was conducted in 1985.

Jan 1, 2010