Search Documents

By A. W. Deurbrouck

Five preparation plants employing concentrating tables for washing 3/8- inch to 0 raw coal were tested. Two of the plants were washing Pittsburgh-bed coal, two were washing Pocahontas-bed coal, and one was washing Elkhorn-bed coal. Samples of the feed to and products from the tables were collected over the normal operating shift. These samples were analyzed, and complete performance criteria were determined. The results of this study show that the concentrating table is an effective fine-coal cleaner even when operating at 40 percent over the recommended 10 tons per hour feed rate. Recovery efficiencies for the 3/8-inch to 200- mesh size fraction ranged from 97.3 to 99.3 percent; maximum yield errors and ash errors were 2.4 and 1.0 percent, respectively; probable errors ranged from 0.074 to 0.115 specific gravity units and error areas from 52 to 73 square centimeters. The amount of minus 200-mesh material in the water used for feed water and dressing water to the table had no significant effect on the sharpness of the separation achieved but did have an effect on the ash content of the clean- coal product. In the one plant studied, the substitution of fresh water for plant circulating water reduced the ash content of the clean coal by about 6 percentage points.

Jan 1, 1963

By Earle S. Burnett

Rotating piston deadweight gages have been used for many years for measurement of pressure to several hundred atmospheres. They have been calibrated by comparison of fluid pressures produced by various loads bearing on the piston bases, as measured by corresponding heights of balancing columns of mercury. When expressed in appropriate units, these ratios of column heights to piston loads are called piston constants. Experimental arrangements and procedures for their determination are presented in this paper, followed by a discussion of their significance and of their subsequent applications.

Jan 1, 1966

By J. W. Paul

A superintendent is one who has the oversight and charge of some organiza- tion or enterprise, with porer of direction. The superintendent of a coal mine is the official who is in general charge of conducting the operation of the nine for the purpose of producing coal; he is accountable to his superiors for all matters that relate to the cost of production and safety in operation, ed under him are all the underground officials and other personnel making up the mine organization. The responsibility of the superintendent covers all the principal phases of mining, purchases of materials, issuance of supplies, accounting, and upkeep of the property and equipriont. In a broad sense, the superintendent must view his job as embraced under four gneral heads: (1) Construction, (2) instruction, (3) supervision; and (4) discipline. The degree of efficiency with which each of these phases of his work is conducted is a measure of the safety factor which the superintendent injects into his job. Injury to workmen and damage to property may be due to neglect of one of these general headings; as for example in the collapse of a scaffold there has been faulty construction which may be found upon investigation to have been the result of faulty instruction or lack of instruction. It may be that the condition of the scaffold was not ascertained in advance of its collapse through faulty supervision, or the discipline of the workmen had been neglected.

Sep 1, 1930

By B. G. Cousins, L. Racine, R. S. MacPhail

"FLEX 31 is a chemically enhanced sodium isopropyl xanthate that has shown improved collection properties over SIPX for copper-bearing and copper-activated minerals. Characteristics such as improvement of recoveries with lower dosages and high pyrite and pyrrhotite rejection capabilities have all been exhibited by FLEX 31.The most improved results have been seen insphalerite flotation. Plant trial work carried out in the zinc circuit at the Louvicourt Concentratorin northern Quebec has produced data showing superior grade and recoveries from rougher concentrates that previously had not been attain-able with other reagents effectively. The improvement over SIPX adds up to an almost$1,000,000 annual improvement on the mine’s bottom line at present zinc prices.IntroductionSodium Isopropyl Xanthate (SIPX) is one of the most popular flotation chemicals on the market today. Somewhat more specific than amyl xanthates, SIPX is used in a variety of ores like copper/zinc, lead/zinc, arsenopyrite/pyrite, and many others (Melis et al., 1991). An investigation carried out by Tennants Research Technology Applications (TRTA), a division of Charles Tennant & Co. (Canada) Ltd., produced a chemically enhanced SIPX that has shown all the advantages of normal SIPX along with improved recoveries of copper and copper activated minerals. The new product has been named FLEX 31. Currently, FLEX 31 is manufactured at the Prospec Chemicals, another division of Charles Tennant & Co. (Canada) Ltd.A large amount of laboratory testing pro-grams have been carried out with FLEX 31 todate (MacPhail and Cousins, 1995; Cousins and MacPhail, 1996). One of the minerals that has a defnite affinity to improved fotation is sphalerite (ZnS). Once activated with copper sulphate, sphalerite has produced some of the most spectacular test work when FLEX 31 is compared directly to SIPX. Plant trials of FLEX31 at Aur Louvicourt Inc. carried out in 1995show that FLEX 31 is far superior to SIPX for activated sphalerite flotation."

Jan 1, 1997

By L. W. Palmer

Compositing or regularization of drillhole data is common practice in mineral resource estimation and is deemed a necessary step in producing unbiased estimates of mineral resources and reserves. Commonly, data are collected over irregular distances due to the varying relative thicknesses of lithologies drilled or sampling/assaying strategies. This necessitates data transformation to regular lengths of equal size to ensure that all data have the same sample support. However, there have been few detailed publications on the effect of this process on the composited data that are subsequently taken forward for the estimation process. In this paper, three currently available compositing methods are reviewed and the effects of inappropriate compositing methodologies presented. It is shown through a case study that compositing samples to different lengths leads to changes in the average and variance of the grades in the drillcores in the dataset, which will impact the final estimated value. These differences are exacerbated by breaks or gaps in data where, for a variety of reasons, there has been no data collection or data have been lost. The importance of appropriately treating blank and zero data is also presented. Globally, these differences might be minimal, but locally may be substantial, affecting the efficiency of the estimation and subsequent use of the results in, for example, mine planning and reconciliation. Further detailed investigation of compositing practices is required if the full implications of compositing are to be understood and any induced bias effectively defined.

Jul 10, 2024

By Michael G. Zabetakis

Investigation of gas explosions usually reveals that the combustible gases have come from transmission and storage facilities or from natural gas or oil wells. However, combustible gases such as methane and hydrogen can derive from biological processes. Hazardous situations have been created in the past by the use of abandoned mines for the disposal of sewage and rainwater, by the interconnection of storm and sanitary sewers, by sealing the openings in manhole covers when repaving the roadway over a sanitary sewer, and by the construction of buildings over or near garbage fill areas without adequately providing for the release of combustible gases.

Jan 1, 1962

By Fabiano Della Libera da Silva

Este artigo propõe uma metodologia para a construção de um Referencial Estatístico para a Utilização Física de equipamentos de mina. Para tanto, calcula-se um valor mensal (RE) apoiando-se em conceitos importantes para a operação de mina e que estão e inter-relacionados, como o comportamento sazonal da precipitação pluviométrica, o Teorema do Limite Central e a Gestão da Lacuna de Resultado. A metodologia proposta foi aplicada em uma mina de ferro a céu aberto e às frotas de transporte de um complexo minerador no Norte do Pará.

Aug 17, 2017

By Torma A. E.

Biotechnological processes are considered to be cost effective especially for situations where the recovery of metals from 'Very large volumes containing trace metal concentrations (less than 10 ppm) is concerned. Microorganisms, alive or dead, or their products can be highly efficient and selective biosorbents for metal concentration. It is important that the metal bound to the biosorbent can be stripped by suitable agent(s) and regenerated for repeated use. The stripped solution should be concentrated enough to be introduced into the common metal recovery circuit. The industrial acceptance of biosorption processes is dictated by increased competitive advantage over other processes. This paper reviews the pertinent literature?, regroups the information, and points out future possibilities for the mineral and metal processing industries.

Jan 1, 1992

By Wm. O. Vanderburg

This report on the mining and milling of tungsten ores is the second part of a general study of the domestic tungsten industry. The first part, comprising general information on tungsten, has been printed as Bureau of Mines Information Circular 6821. The purpose of these papers is to increase efficiency in the mining, preparation, and utilization of the tungsten resources of the United States. The tungsten industry forms so small a part of the vast mining and metallurgical operations of the illation that private metallurgists have not had enough inducement to give special attention to the recovery of tungsten minerals from the ores, and many of the small companies are financially unable to undertake research work. A study of the milling of tungsten ores reveals that further improvement is possible, especially in the treatment of slimes. Recent experimental work by the Bureau shows that the flotation process is applicable to certain tungsten ores. The future of the tungsten industry it the United States depends to a great extent on utilization of the low-grade deposits of the contact-metamorphic type.

Jan 1, 1935

By J. C. Barrett

Bureau of Mines research on the arc welding characteristics of titanium was initiated in 1948. Little was known about the art except that the easily contaminated metal required more protection from the atmosphere during welding than most other metals. Chambers were designed and built within which titanium could be welded with adequate inert gas protection. Welds were made and their properties studied, and prototype items were made successfully. This report, presenting a resume of the titanium arc-welding experiments undertaken by the Bureau of Mines, demonstrates that the process is successful if conducted under proper conditions and describes the welding of prototypes. INTRODUCTION The Bureau of Mines' first report on methods of joining titanium covered the subject of spot welding,4/ outlining the conditions necessary for producing spot welds in ductile titanium consolidated by powder metallurgy methods and describing the characteristics of such welds. This report embraces the field of fusion weld-ing of titanium and traces the development of suitable methods and equipment for producing such welds.

Jan 1, 1956

By Kwame Awuah-Ofei, Sisi Que, Shaochun Yuan, Yumin Wang, Ziwei Ding

This research sought to facilitate improved stakeholder analysis in mining by providing further insights into the preferences of local community members using discrete choice theory. While recent research has demonstrated the usefulness of discrete choice theory in mining stakeholder analysis, no previous work has examined which discrete choice model (DCM) is most suitable. This paper provides a research note on a case study in a mining community that was performed to compare three DCMs. After a thorough examination of the benefits and deficiencies of all models, this study concludes that the conditional logit model stratified by questions is the most useful DCM for mining stakeholder analysis. The recommendation is based on the usefulness and accuracy (ability to match the survey data) of this model.

Jul 25, 2022

By N. S. Dalal, Xianglin Shi

"The mechanism of vanadium(V) V ) toxicity is still not fully understood in spite of extensive current effort (1-3). The presence of a vanadium(V) V ) -dependent NAD ( P )H oxidase in cell membranes suggests that at least one of the pathways involves oxidation of NAD(P)H (1-3). Considerable effort has therefore been devoted to finding the mechanism of NAD ( P ) H-oxidation by va¬nadium( V ) (1-19). Recently Liochev and Fridovich (4, 16) provided a critical review of vanadium( V) -stimulated NAD (P )H oxidation by plasma membranes. They out¬lined a mechanism in which vanadium(V) V )-stimulated oxidation of NAD ( P )H by biomembranes involves an O2 - initiated free radical chain reaction (4 ). While the above may be the major pathway for the vanadium-me¬diated NAD (P )H oxidation in membrane-related sys¬tems, some recent results suggest that in the presence of NADPH the flavoenzyme glutathione reductase can function as a vanadium(V) V ) reductase (18). Because of the significance of this result in relationship to the mech¬anism of vanadium( V) metabolism and the novelty of the metal-reductase behavior of a flavoenzyme, we have car¬ried out additional studies on one-electron reduction of vanadium( V) by two other, related flavoenzymes: lipoyl dehydrogenase and ferredoxin-NADPH oxidoreductase. These two enzymes were selected because they are known to catalyze a one-electron reduction of Cr ( VI ) (19-21 ), which is isoelectronic with vanadium( V ).The present study also reports on the generation of hydroxyl ( • OH) radicals in the vanadium( V) -flavoen-zyme redox system without exogenous H2O2. The • OH study was undertaken because • OH radicals are known to be generated in reactions of vanadium( IV) with H2O2 (17,18,22-27). For example, Piette and co-workers (17, 22) have studied effects of vanadium(IV) IV ) on lipid per-oxidation and NADPH oxidation and suggested that va-nadium( IV) -induced • OH radical formation may play an important role in vanadium( V) toxicity. Carmichael (25, 26) investigated the reaction between a RNA /VO 2' complex and H2O2 with a view to probe the possible re-lationship between vanadium( IV) -mediated • OH radical generation and DNA damage. He has suggested that in this reaction the • OH radical adds to the C (5) carbon of uracil, causing nucleotide damage, similar to what occurs in the nucleotide /Fe2+ / H2O2 reaction (28) and in y-irradiated aqueous solutions of nucleic acids (29 ). To our knowledge, however, there is as yet no report on ·OH radical generation in any reaction involving the reduction of vanadium ( V) by a well-characterized enzyme, without exogenous H20 2 • The present study provides evidence that ·OH radicals can form in a flavoenzyme-mediated reduction of vanadium( V) to vanadium( IV) and that this process involves also the reduction of molecular oxygen ( 0 2 ) to H20 2 • The H20 2 thus generated reacts with vanadium( IV) to produce ·OH radical, in analogy with the Fenton reaction ( Fe2 + + H20 2 - Fe3 + + OH- + ·OH)."

Mar 1, 1992

By H. El-Faramawy, A. Ahmed, M. Eissa, M. El-Fawakhry, T. Mattar, S. N. Ghali, E. M. Kotb

As a result of the depletion of high-grade manganese reserves, it has become necessary to consider the exploitation of low-grade manganese ores. The main problem of low-grade manganese ore is the low Mn/Fe ratio, which makes it unfit for the production of manganese ferroalloys. In this work, a selective reduction technique was used for smelting low-manganese ore in the presence of coke and fluxing material in an electric submerged arc furnace to obtain a rich manganese slag and low-manganese pig iron. The product slag was blended with medium-manganese ore and smelted in an electric submerged arc furnace, in the presence of coke and the fluxing agent, to produce silicomanganese alloy. The influence of reducing agent ratio, charge basicity, and charge Mn/Si ratio on the smelting process was investigated. The optimum conditions were found to be a coke ratio of, 1.35, Mn/Si ratio of 2.0, and charge basicity of 2.5. The silicomanganese alloy produced under these conditions satisfies the specifications for Si16Mn63 and Si17Mn65. The experimental results were applied on a pilot scale, producing a silicomanganese alloy with a chemical composition close to that of the standard specifications.

Jan 2, 2022

By E. W. Davis

IF the tonnage of merchantable iron ore remaining in the Lake Superior district is divided by the average of the annual shipments for the past 20 years, it will be found that this ore supply will be exhausted in approximately 35 years. This computed exhaustion period would be an indication of the future activities of the iron-mining industry if it were not for the fact that merchantable ore is being manufactured from low-grade ore, of which there is an almost inexhaustible supply in the Lake Superior district. It is true that at present only the simplest of these low-grade ores are being concentrated to any considerable extent, but progress is being made with the treatment of the more complex ores, and now, in addition to 20 washing plants on the Mesabi Range, three plants are equipped with jigs for the treatment of ore that cannot be concentrated simply by washing. The latest addition to the ore-treating plants of the Mesabi Range is a magnetic roasting and concentration plant at Cooley, Minn., in which ore that cannot be concentrated either by washing or by jigging is roasted to the magnetic state and concentrated on magnetic separators. This plant is beginning its third season of operation, and while it is too soon to make definite predictions, there are strong indica-tions that this new process may make commercially possible the manu-facture of high-grade, merchantable iron ore from large quantities of low-grade ore now considered worthless. After the iron oxide contained in an ore has been converted to mag-netite, almost any desired grade of concentrate can be produced, using magnetic-concentration equipment of the types now in general use for the concentration of the natural magnetites of New York, New Jersey and Pennsylvania. The conversion of hematite (Fe2O3) to magnetite (Fe3O4) is easily accomplished by heating the ore to a dull red tempera-ture in a reducing atmosphere. The reaction is slightly endothermic, and while it requires 200 B.t.u. to heat to 900° F. one pound of hematite ore containing 45 per cent Fe, it requires only 100 B.t.u. to convert the oxide into magnetite. In the laboratory, using small quantities of ore, this conversion is very simple, but large furnaces suitable for commercial

Jan 1, 1936

By Robert H. Peters

This U.S. Bureau of Mines report identifies the types of serious accidents that occur most frequently at small underground coal mines and describes the strategies that could help prevent these accidents. A wide variety of methods for improving safety are suggested, including improvements in the design of equipment, work procedures, work schedules, safety programs, and emergency response plans, as well as techniques for diagnosing the potential hazards associated with new technologies and work procedures. Some of the papers in this volume focus on preventing specific types of mining accidents--ones associated with materials handling (primarily back injuries), equipment maintenance, improper machine guarding, and ground failure during retreat mining. Although the recommendations in this volume are heavily influenced by research performed at underground coal mines in the Appalachian coalfields, most of the papers contain advice that is equally pertinent to almost any type of mine.

Jan 1, 1994

By D. T. White

Pressure acid leaching of nickel laterite ores typically involves the production of an intermediate product that is releached and refined to pure nickel and cobalt products. BHP Billiton is developing the Ravensthorpe Nickel Project to produce up to 50,000 t/y of nickel via a mixed hydroxide intermediate, which will be refined at its Queensland Nickel (QNI) Yabulu Refinery near Townsville, Queensland. The hydroxide precipitation flowsheet has been adapted to process high magnesium ores through an atmospheric leach stage, eliminate iron(III) as jarosite and oxidise iron(II) during neutralisation. The neutralisation conditions are controlled to precipitate aluminium, chromium and silicon, and to ensure good solid-liquid separation. Soluble impurities such as magnesium are purged with the tailings stream and will be managed over the long term by crystallisation in evaporation ponds.

Jan 1, 2006

By B. Peszko

There are many measuring methods of grain sizes. Taking into consideration the fine grained materials, one of the existing techniques is measurement of grain size by the Coulter Counter method. This method is based on the measuring the changes of electrolyte resistance during grains flow through the calibrated diaphragm. This method is relatively simple to apply, significantly precise and the results are given quickly. However, the problem is that the measurements are limited by the size of diaphragm. Because of this situation, measurement of grain sizes by this instrument is possible in range from 10% to 60% of diaphragm diameter. This limitation causes the necessity of re-placing diaphragm in case when the measured grain size distribution concerns the material of large size range. In purpose of determining the total grain size distribution, the synthesis of some partial distributions, given for individual grain fractions (with different diaphragm applied), is required. This is possible to do by calculating the mixture of distribution functions, created from the partial distribution functions. Two materials were selected to research: quartzite and glass, which were comminuted in cylindrical crusher, additionally grinded, screened and then analyzed by Coulter Counter for five grain fractions: 0~125 µm, 0~80 µm, 0~56 µm, 0~40 µm and 0~25 µm. For each fraction, five different partial distributions were given (in case of glass ? four), which are the basis for the creating the joined grain composition. To assure the adequacy of the given distribution function, it is necessary to obtain the possibly best approximation of partial distributions. In the work, both the parametric and non-parametric methods of density approximations of investigated random variable. For each grain fraction the approximations were done by three traditional distribution functions: RRB, GSA and log-norm distribution functions and three methods of non-parametric approximation: Gauss kernel, Epanechnikov kernel and orthogonal Fourier series method. As the criterion of the certain distribution function acceptance, the value of the residual deviation was assumed, given by the formulae:

Jan 1, 2014

Western Mining Corporation has grown from a small gold exploration and mining company, funded by large established mining companies, into a large multi-commodity and multi-national mining company with shareholders who no longer have the same understanding of mining as the founders. Ore reserve calculation methods and reporting procedures have gradually changed throughout the group during this growth. These changes have been led by the newer mines, in particular the Kambalda nickel mines, where the need for more global, less conservative reserves were required to justify capital and forward sales contracts and to inform shareholders of the true worth of their company. This change in attitude to reserves has flowed back to the gold mines and has allowed a better informed management and investing public to plan for the future. Management of the calculation of reserves remains the responsibility of individual mining operations, but a corporate reporting and management structure exists through the office of the Director of Exploration and divisional chief geologists who strive to maintain standards of calculation and reporting. Specialist ore reserve geologists are starting to justify their place in the organisation, particularly at the larger operations. Reporting to the new AusIMM Standards is fully supported, although the amount of supplementary information requested will need to be considered carefully because of the large number of factors that make up even the simplest reserve.

Jan 1, 1990

By Alexsandro Berger

Many thickener operations continue to be constrained by their ability to process consolidated underflows with high yield stress and associated rheological characteristics. To maximise separation efficiencies within a thickener operation the use of both engineering and reagents are always considered. BASF is developing a Novel Flocculant Technology (NFT), which combines both of these aspects to enhance the performance of the thickener operation, improving the areas of pumping efficiency, underflow density and throughput. The development progression through stages of laboratory scale batch test work to pilot scale dynamic testing has demonstrated the ability of BASF NFT to maintain effective flocculation performance whilst increasing the rate of underflow consolidation, and significantly reducing the associated underflow yield stress of the treated material. This paper will present application data through full scale dynamic testing conducted on a granite washing circuit to demonstrate the performance benefits that NFT offers to a thickener operation. Compared to the conventional flocculant treatment, within the operation parameters and conditions employed during the full scale trials, the NFT produced a reduction in underflow rheology (yield stress) of around 45 % relative to a given solids and improved the underflow consolidation by providing at least 20% relative higher underflow solids loading than the upper limit of the given typical thickener operation. Keywords: flocculation, thickener operation, rheology, yield stress, underflow density, throughput, slump test

Sep 1, 2012

By Alexander Malahoff

The most exciting frontier in Ocean Technology is represented by a new class of Marine Bioproducts, the source of which lies in marine microorganisms. The microorganisms include microalgae, bacteria and archaea. These organisms represent very diverse, adaptive life forms and in their metabolic processes use carotenoids, polyunsaturated fatty acids, ultraviolet blockers, as well as a wide range of enzymes that are pivotal in the production of new pharmaceuticals and nutraceutical products. These organisms cover a wide spectrum of ocean environments, from the shallow to the deep, from the normal to the extreme. The technological challenge is in the identification of candidate organisms, in the screening for valuable enzymes, and in the industrial production. A whole new range of collecting strategies involving submersibles, ROVs and in situ ocean floor instrumentation is emerging. New non-polluting industrial chemical processes involving the use of photobioreactors and extremophile bioreactors for breeding and monitoring these organisms in neo-farming technology is emerging. The commercial value of these candidate products is immense, as is the range of potential organisms. The dimension of this new industry is global. The Marine Bioproducts Engineering Center (MarBEC), funded by the National Science Foundation (NSF), has been established at the University of Hawaii. The vision of MarBEC is to develop a seamless research system stretching from undergraduate education to industry for the purposes of producing valuable marine bioproducts outside of the normal chemical factory production. MarBEC is uniquely and strategically placed in the Pacific to explore, find, and adapt highly bioactive marine micro-organisms found in the tropical ocean. We have watched the increasing need by the ever-

Jan 1, 2000