Search Documents

By G. R. Hopkins, E. M. SEELEY

According to reports received by the Bureau of Mines, Department of Commerce, as of Jamary 1, 1930, there were 1,035 natural-gasoline plants in the United States, with a total daily capacity of 10,516,000 gallons. (These data do not include one small plant in Alaska.) The last similar survey, that of Jamary 1, 1928, showed a total of 1,155 plants of 8,048,000 gallons daily capa- city. This in two years time the number of plants has decreased by 120, but the total capacity has increased 2,468,000 gallons or 31 per cent. This is roughly equivalent to the gain in production over the same periodi Over half of the increase in total capacity was registered in California, where the development of flush oil production having a comparatively high gas-oil ratio in such fields as Santa Fe Springs led to construction of some new plants and material enlargement of others. Of the total plants, 999 were operating on Jamary 1, 1930, and 36 were shut down. This compares with 1,060 operating and 95 shut down two years ago, which indicates a tendency to dismantle plants as soon as they become obsolete or umrofitable. The total daily capacity of the plants operating on Jamiary 1, 1930, amounted to 10,278,000 gallons, or 98 per cent of the total, leaving only 238,000 gallons, or 2 per cent, for the shut-down plants. This contrasts with the refining industry, which usually has 5 per cent of its total capacity idle; the difference is due to the relative ease with which a refiner can secure a crude supply as against the difficulty the natural gasoline manufacturer has in reestablishing his gas connections. During 1929 the average total daily capacity of the operating plants was 9,899,000 gallons, while the average daily production amounted to 6,015,000 gallons. This indicates that the plants operated during 1929 at 61 per cent of their capacity. Although over 60 plants were dismantled in Oklahoma during 1929 the State continued to rank first in total mumber. California was second in mumber of plants with 165, and was one of the few States that showed a gain since the

Jul 1, 1930

In 1962 and 1963, two in situ combustion pilot tests were conducted in the shallow Second Venango sand near Reno, Pa. Because of poor oxygen utilization and lack of production response, both tests were considered failures and were terminated. The area was then relatively inactive until late 1966, when a development well drilled near the 1963 test site had surprisingly good production in what was considered to be a pressure-depleted reservoir. Other wells drilled in and around the old thermal pilot areas also came in as good oil producers. This report presents a study of the increased oil production from the Second Venango sand in the Reno area, and the apparent connection of the present production response and the old thermal pilot tests. Apparently combustion occurred in the Second Venango sand after the 1962 and 1963 experiments were terminated and, supported by large volumes of air left in the reservoir after the 1963 test, generated carbon dioxide which helped repressure the formation. This field evidence of combustion warrants another pilot experiment to further explore the use of properly designed in situ combustion techniques in increasing production from the Second Venango sand.

Jan 1, 1971

By Daryl R. Tweeton

The Bureau of Mines measured the geochemical changes as H2S04 was used for in situ uranium leaching by Rocky Mountain Energy Company near Casper, Wyoming. Cores and ground water were analyzed before leaching. Water samples were taken from observation wells located between injection and production wells as the leach solution was brought up to full strength in several steps. Measurements were made of pH, Eh, temperature, conductivity, total dissolved solids, dissolved oxygen, HC03, U, V, Na, K, Ca, Mg, SO4, C1, Mo, Mn, Fe, Al, Si, F, P, As, and Se. The data were gathered to assist in geochemical modeling of leaching and to study the potential environmental effects of acid leaching. Environmental considerations appear favorable. For example, the concentration of Se, a toxic element often found in uranium deposits, stayed below the EPA standard for drinking water.

Jan 1, 1979

By WenJun Dong

This paper presents the stability assessment of the steel pipe piles that are used to support a deadman beam to anchor an adjacent bulkhead wall. Finite element analyses are performed to assess the stability of the bulkhead wall and determine the required tie-back force to the pile. The piles are relatively close to the bulkhead wall such that their soil resistance wedge zones are not fully developed but truncated by the bulkhead wall. The reduced lateral resistance capacity of the anchor piles is determined by applying the Coulomb wedge method on the truncated soil passive zones between the pile and wall. Both the conventional soldier pile stability (in terms of force and moment equilibrium) and Winkler soil spring (for soil-pile-interaction) analyses are used to assess the stability of the anchor piles.

Sep 8, 2021

By Xuehui Li, Xinshuai Shi, Jun Wang, Jianguo Ning, Shang Yang, Zhaohui Zhang

Pressure relief is an important step in preventing and controlling rock burst disasters. Hydraulic slotting has emerged as a strategy for pressure relief and energy release in roadway surrounding rock. There is no qualitative description for the response relationship between hydraulic slotting parameters and the degree of pressure and energy release in a roadway, which is a scientific problem. In this paper, theoretical analysis, numerical simulation, and on-site industrial practice were comprehensively used. First, a structural model for the pressure relief and energy release of coal by hydraulic slotting in a deep roadway was established, and the pressure relief and energy release principle by hydraulic slotting was revealed. The principles and methods for determining hydraulic slotting parameters in the roadway were proposed. Three evaluation indices for the pressure relief and energy release effect of coal after hydraulic slotting were proposed, namely, the stress ratio of coal, elastic energy density ratio of coal, and displacement rate of the roadway rib. According to the evaluation indices, the degree of pressure relief and energy release was divided into three levels: reverse pressurization, full pressure relief, and transitional pressure relief. Then, a FLAC3D numerical model was constructed, the levels of pressure relief and energy release under different hydraulic slotting parameters were analyzed, and the optimal slotting parameters were determined. Finally, on-site industrial practices were carried out in Panel 7312 of the Xinhe Coal Mine. An effect test showed that the effect of pressure relief and energy release was remarkable after hydraulic slotting was adopted on the roadway surrounding rock, which can effectively reduce the risk of rock bursts. These research results can further improve hydraulic slotting technology systems and provide a theoretical basis and technical reference for the stability control of deep roadway surrounding rock.

Sep 20, 2023

The present study is devoted to improvement of the leaching efficiency during phosphorous removal from high phosphorous gravity-magnetic concentrate. Before leaching the concentrate has been subjected to roasting with the addition of either Ca(OH)2 or CaO. The oolitic iron ore is roasted at 900°C for one hour. This reflects in reaction between alkaline earth additive and quartz, aluminosilicates, phosphorus, and some other minor components of the gangue minerals. The application of leaching, physical separation, and wash out of salts has resulted in the decrease of phosphorus from 0.7 to 0.15 % and it is established that the major influencing factor is the concentration of acid and to a less extent duration of the leaching process. About two third of the phosphorus can be removed by roasting with 3 % CaO to hematite, coarse grinding to d50 0.3 mm, dry high intensity magnetic separation and leaching of the magnetic fraction with hydro-chloric or nitric acid.

Sep 1, 2012

By Shawn McWilliams, Aini Sun, Mike Lichte, Greg Colzani

The Allegheny County Sanitary Authority (ALCOSAN) adopted its Clean Water Plan (CWP) in May 2020, as part of a federal consent decree to comply with the USEPA’s Combined Sewer Overflow (CSO) Control Policy. Planned improvements include constructing a new regional storage/conveyance tunnel system, promoting green infrastructure/ source control, and expanding the treatment plant. Preliminary planning for the tunnel system was completed in October 2020. The Ohio River Tunnel (ORT) project is the first of three tunnel projects that make up the regional tunnel system. The ORT project began final design in 2021. This paper discusses the advancements made to the ORT preliminary planning concepts considering property availability, alignment optimization, tunnel boring machine evaluation, contract packaging and delivery schedules.

Jun 13, 2023

By E. M. Tignor

A research program to aid development of improved methods for increased production of petroleum from partly depleted reservoirs is a vital part of the Bureau of Mines effort to effect true conservation of that mineral resource. This report presents results of an investigation to identify the clay minerals within some Appalachian petroleum-reservoir sands, the effect of clay content on the fluid-flow behavior of those sands, and the use of brines in water-flooding operations. Permeability measurements using kerosine, calcium chloride brine, simulated oilfield brine, potassium chloride brine, sodium chloride brine, and distilled water were made on reservoir-rock cores. Clay fractions were separated from sand grains of disaggregated portions of each core sample, and the clay minerals were identified by the differential thermal analysis method. Relations of the permeability to various fluids were developed.

Jan 1, 1957

By M. Deutsch, E. González, M. Williams

"There is uncertainty in ultimate pit limits due to geologic variation and unpredictable economic landscapes. In this work we show how this uncertainty affects the ultimate pit and how it can be analyzed to improve the mine planning process. A stochastic framework using geostatistical simulation and parametric analysis is used to model the effects of geologic and economic variation on ultimate pit limits and overall project economics. This analysis is made possible by a new, highly efficient pit optimization implementation which can be automated and set up to calculate ultimate pits for hundreds of different scenarios in a matter of hours. Quantifying ultimate pit uncertainty early in the mine planning process allows mining engineers to make informed decisions regarding infrastructure placement, and to mitigate the possibility of incurring substantial costs relocating critical mine facilities. INTRODUCTION The mining industry is increasingly concerned with the effects of risk and uncertainty. Uncertain prices, unpredictable global markets, and unknown foreign exchange rates can alter the economic viability of a mining project in substantial ways. This economic uncertainty is compounded by geologic uncertainty. The extent and quality of any given deposit cannot be fully measured and is not known before consequential decisions must be made. These two sources of uncertainty are responsible for the majority of deviation between what happens during operation and what was initially planned. Understanding and explicitly quantifying this uncertainty will lead to better decision making and allow mining engineers and investors to be aware of what may occur. It is unrealistic to believe that one model, estimated from sparse measurements, is enough to capture both geologic and economic uncertainty and allow for optimal decisions. The entire breadth of uncertainty should be considered, as both upside and downside risks have large impacts on the investment potential and operational efficiency of mining projects. The workflow presented here uses Monte Carlo simulation and parametric analysis together to explicitly analyze the breadth of geologic and economic uncertainty as it applies to ultimate pit calculation and long range mine planning."

Jan 1, 2015

By W. E. Davies

"This paper is the sequel to that on Developments in Sintering Efficiency delivered by Davies and Mitchell at the International Ore Dressing Congress, Stockholm, 1957. Attention is drawn to the fundamental concept of sintering as a heat transfer process, in which the ignition heat is continually transferred onward through the bed as a heat wave. By its passage, this heat initiates endothermic 'changes, such as carbonate decomposition, whose energy requirements are supplied by the combustion of the fuel contained in the bed.Ideally, the heat wave should be generated by the ignition hood followed by the pre-heating of the incoming air. The fuel content of the bed should be no more than the theoretical quantity needed to balance the endothermic changes. In practice, the heat wave is seriously short of energy and this is offset by excess fuel in the bed. As a result, sinter quality suffers, more return .fines are produced, and fuel is wasted, a loss of efficiency which could be avoided if the fundamentals of correct ignition were more widely appreciated.Sintering speed, otherwise heat wave velocity, is a function of the rate at which the incoming air acquires .heat from the cooling sinter and imparts it to the unburned feed below the combustion zone. It is thus a function of rate of air flow and so depends on bed permeability>. Ways of• improving and maintaining permeability at the maximum consistent with thorough sintering are discussed, particular reference being made to taconite concentrates. The possibilities of recrystallizing refractory ores into forms more amenable to physical concentration techniques by sintering are visualised, very little expenditure on heat energy being required when the process is operated near the ideal conditions."

Jan 1, 1960

By V. E. McKelvey

Any discussion of growth and future requirements has to begin with people--both their number and their needs. Both have been rising ever since any American can remember. Together, the number of people, which has been increasing rather modestly, and their wants and desires for material things, which have been increasing very sharply, seemed to have comprised a growth imperative in mineral consumption in the United States, especially during the last several decades. While the Nation's birthrate is now well below the replacement rate and still falling, the built-in momentum of the post-World War II population boom will continue to be felt well into the 21st century. Even using the modest projection of a 0.8 percent yearly increase, we are still looking at the possibility of 265 million Americans being around by Year 2000.

Jan 1, 1975

By Donald C. Strimbeck

The Bureau of Mines, U.S. Department of the Interior, is conducting research and development on a coal-burning gas turbine. This work includes the development of (1) turbine blades resistant to coal ash erosion, (2) equipment to feed coal under pressure to a turbine, (3) an efficient combustion system, and (4) equipment to remove coal ash from the gases that drive the turbine. Initial emphasis is being placed on testing the first turbine ever equipped with blades designed specifically for use with coal as the fuel. Operating tests with this turbine are now in progress. This paper describes the Bureau's coal-burning gas turbine development program and progress on this operating test.

Jan 1, 1964

The 2-4D window shown above is the base startup window which allows you to begin a new project. ??Setting up the project is the first step ??The next step is to setup the properties to be used in this project

Feb 1, 2008

By B. W. Haynes

With the national focus on energy, the combustible fraction of urban refuse is being extensively considered as a fuel supplement for coal in the generation of heat and power. The objective of these analytical studies by the Bureau of Mines was to determine the concentration of major, minor, and trace elements in the combustible fractions collected at various locations in the Bureau's urban refuse recycling pilot plant located at College Park, Md. The samples processed through the plant were submitted by various municipalities that are considering resource recovery as an alternative to landfill or other means of disposal. Twenty-five elements were determined in samples from six geographic areas and were compared with element concentrations found in typical coal samples.

Jan 1, 1977

By John R. Woodcock

The Kitsault molybdenum deposit lies along the east margin of thecoast Batholith Complex near the head of the fiord of Alice Arm. It is 800 km (497 miles) northwest of Vancouver, British Columbia. The deposit is located on Lime Creek 8 km (5 miles) from the coast on a wide dissected upland valley at an elevation of 600 m (1969 ft). It is an area of coastal rain forest with high annual precipitation and extremely high winter snowfall. Although the area is of high relief, outcrops are largely restricted to ridges and canyons. Most of the area is covered by the coastal vegetation or wet swampy upland areas. The south edge of the molybdenum deposit was exposed in a sharp canyon; however, outcrops over the remainder of the deposit were largely restricted to a few small exposures of resistant hornfels. The mineralization is related to an elliptical porphyry stock of 52.3 m.y. age which intrudes argillites and microgreywackes of the Late Jurassic Bowser Group. A circular zone of alteration, with a diameter of about 700 m (2297 ft), occurs in the north end of the stock and the molybdenite mineralization is concentrated in the outer parts of this zone of alteration. Thus, the northern part of the mineralization occurs partly in the hornfels and partly in the stock, whereas the southern side of the ring of mineralization cuts across the middle of the stock. Zoning within this system includes a central circular area of almost complete replacement of quartz plus K- feldspar and this grades sharply outward into a phyllic zone. Clay alteration is largely localized along late faults. The ring of molybdenite mineralization is partly overlapped and partly surrounded by a zone of pyrite mineralization. Some chalcopyrite is coextensive with the pyrite zone. Late polymetallic veins fill two conjugate fracture sets. These quartz veins contain galena, pyrite, some chalcopyrite, and a number of lead-bismuth sulfosalts.

Jan 1, 1991

By Robert Goldstein

A computer program for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. To provide a data base for these calculations, eleven 3-D machine models were prepared and the outputs of three luminaire types were measured. Calculations were done for thirty different configurations.

Jan 1, 1977

By Peng Gao

Coal-based reduction followed by magnetic separation is an innovative technology used in processing refractory iron ores. Given that size is essential to the separation of the metallic iron from the gangue, the morphology of metallic iron particles and their evolution during coal-based reduction are investigated in the present work. The size of the metallic iron particle increased from 128.76 µm to 565.70 µm when the reduction time increased from 20 min to 60 min at 1,225° C and C/O (i.e., the amount of coal addition in terms of the gram-atomic ratio of the fixed carbon in the coal added to the combined oxygen in iron oxides) of 2.5. Based on our microstructural and metallographic analysis, the iron ore reduction process can be divided into three stages: (1) metallic iron particle formation, (2) iron oxide reduction and metallic iron assembly and (3) metallic iron particle growth. Almost all iron oxides are reduced to metallic iron in the second stage. These newborn metallic iron particles are energetically active and able to assemble and grow, and are eventually separated from the gangue. The large metallic iron particles benefit the subsequent magnetic separation process.

By B. W. Jong

The Bureau of Mines studied reinforcement of sulfur concretes using glass, polyester, and aramid fibers. The objective of this research was to determine the feasibility of fiber-reinforcing the sulfur concrete to enhance the flexural properties. Optimum fiber sulfur concrete compositions were formulated with a cement-to-fiber ratio of 9.0:1 for glass-fiber and polyester-fiber sulfur concretes and 12.1:1 for aramid-fiber sulfur concretes. Test samples were prepared using techniques developed by the Bureau of Mines. Flexural strength values of up to 50 pct of compressive strength values were achieved with fiber additions. With non-fiber-reinforced sulfur concrete, the values ranged up to 20 pct. The impact strength and fracture toughness of sulfur concretes were increased sig-nificantly by reinforcement with glass or with aramid fiber and were adversely affected by use of polyester fiber. Strain tolerance was doubled and failure mode was shifted from catastrophic to noncatastrophic type by adding glass fiber. The glass-fiber and aramid-fiber sulfur concretes are resistant to acid corrosion and have proved durable in freeze-thaw cycles. This laboratory and field evaluation has shown that fiber reinforcement of sulfur concrete is feasible and that it enhances the flexural properties.

Jan 1, 1985

By J. Pancher

"Stainless steel castings are used in abundance in the mineral processing industry. In rotary kiln-based processes, these castings are typically exposed to high loads, corrosive elements, mechanical abrasion and cyclical temperature exposure. In the processing of iron ore pellets, it is typical to use a traveling grate preheater or a straight grate furnace to heat the pellets. Both machines have a conveyor that is mainly comprised of high temperature stainless steel castings. It is these castings which are the focus of this study. The expected life of these castings can be quite short, their cost quite high and the effort to replace them very labor intensive. The goal of this study was to gain a better understanding of the failure modes of these castings. With that basic understanding, modifications to the alloy content could be made to achieve a new operational paradigm. That paradigm could be a cheaper casting, a longer lasting casting or a casting tailored to special operating conditions (for example, highly corrosive gases or sudden temperature shocks). Over the past 4 years, Metso Minerals has sought to achieve a better understanding of the failure modes through modeling, laboratory testing and sampling of used castings from various end-users. In addition, we have tested new alloys in a laboratory setting and also in the field to see how they would perform compared to the existing ""standard casting"". Our testing has revealed interesting data concerning the impact toughness, sigma phase content and formation, chloride attack and other performance attributes of various grades of stainless steel when exposed to cyclical temperatures. Interesting results were also obtained concerning the addition of rare earth elements (Niobium, Boron, etc), nitrogen and manganese to a typical ASTM A297 grade of stainless steel. To date, a few hundred test castings have been installed in iron ore pellet plants worldwide. Many of these test castings have already experienced a year or more of operation with good results.INTRODUCTION Cast stainless steels (ASTM A297 and similar) are a main constituent used in the construction of iron ore pelletizing equipment. A typical straight grate pelletizing machine would contain upwards of 160,000lbs of ASTM A297 Grade HH castings. With a typical casting lasting only two to four years, and a casting costing around $35USD, it is easy to see that the castings are a main contributor to the overall cost of producing the pellets. Grade HH and HI (see chemical composition listed below) became the “go to” materials in the 1960’s and very few changes have been made to this day (the exception being plants that switched to flux pellet production in the 1980’s)."

Jan 1, 2015

By E. C. Lane

This paper is the second report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relating to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 31293. A third and concluding paper giving the results of other tests will be published as soon as these tests have been completed. The present paper deals with the data of the twenty-third semiannual survey presented in accordance with the revised specifications for United States Government motor gasoline. The sample numbers used are identical with those used in Report of Investigations 3129, with additional data included for copper strip corrosion (method 530.22),4 and sulphur content by the lamp method. Three hundred and twelve samples were collected and analyzed in this survey. Two hundred and seven samples were competitive-price gasolines and one hundred and five samples were premium-price motor fuels.

Jan 1, 1931