Search Documents

By J. H. Viljoen, C. H. Graan, N. B. Strydom, J. S. Greyson

M J Martinson (Fellow) There is everywhere a lamentable dearth of quantitative information on occupational factors affecting the health and safety of mineworkers, and as the authors point out in their introduction underground lighting is one of the factors which has received little attention in South Africa prior to this welcome paper. Since the authors are to some extent pioneering, it is perhaps inevitable that the paper should raise more questions than it answers, but nevertheless it provides a provisional yardstick against which the need for, and success of, remedial action may be judged. Before commenting in detail on a few aspects of the paper it may be worthwhile to summarize the statutory provisions relating to underground lighting, contained in Chapter 15 of the Regulations promulgated in terms of the Mines and Works Act 27 of 1956. Chapter 15 is entitled `Lighting, Safety Lamps and Contraband', but in the context of the present paper only four simple regulations need be noted: firstly, no person shall work or travel in an unilluminated part of a mine unless he carries a light ; secondly, adequate stationary lights shall be provided at stations and certain other localities in shafts, winzes and places used for winding; thirdly, mechanically propelled conveyances shall be provided with an effective bright light shining in the direction of travel; and fourthly, moving machinery to which personnel have access shall be illuminated so as to be clearly visible. In all four regulations the standard of lighting to be provided is wholly subjective, and under these circumstances the wide inter- and intra-mine variations in light intensity disclosed by the study are hardly unexpected. Nevertheless the data presented in the authors' Table I raise three points (1) Is there any evidence that the 19 mines visited during the survey are representative of the 45-50 large gold mines in South Africa, or that the shafts selected are representative of the respective mines? Mine managers would scarcely be human were they not to offer better lit working places for the survey; perhaps the use of a scaling factor (e.g. tonnes or transit mineworkers per shift, kilowatts, etc.) for each working place might have helped to put the figures in perspective. (2) Looking at two of the more numerous - and probably important - of the ten working places included in the survey, i.e. stations and tips, one is struck by the marked. skewness of both intensity distributions (with higher frequencies at the lower intensities) and the abrupt cut-off in both cases just short of pitch darkness. Thus, of the 45 meaned readings recorded at 26 tips no less than 19 fall in the lowest range of 0,1-0,9 1m/ft2, with but one tip in total darkness; of 46 readings on 26 stations, 7 fall in the lowest range and none is in total dark-'1 ness. Although a light with an intensity in the range 0,1-0,9 1m/ft2 may satisfy the regulations, it is certainly arguable that in some situations it may be safer to have no light at all. (3) In view of the skewness referred to above, one wonders how meaningful are the `total average light intensities for (the gold mining) industry' quoted in Table I, which the authors compare with illumina¬tion levels found in other countries. Looking at tips again, one notes that 34 out of 45 meaned intensity readings fall below the `total average' for tips, and only 10 exceed it. From this it may be concluded that a few well-lit working places included in a `total average' may conceal a plethora in Stygian gloom. In their discussion the authors make fleeting reference to the effect of underground lighting on productivity and accident rates, without however quoting any South African experience in this regard. Intuitively it seems highly likely that better lighting (in the widest sense) would improve productivity and reduce accidents, and of course it is in these areas that the mining industry might seek economic justification for providing better lighting. It is all the more regrettable therefore that these factors were not studied simultaneously with the present investigation, especially at the Psychological Division of the Human Sciences Laboratory has recently published a study on underground accidents in the gold mining industry without making any reference whatsoever to lighting as a causal factor. In the event neither of the two studies enables us to make an economic appreciation of the situation, and this seems to be a classic example of a situation where some dovetailing of research effort would have greatly increased the useful return. On the effect of lighting on accidents, it may be noted that in 1939 Mickel presented some very interesting statistics to the Mine Managers Association of the Transvaal2, on the improvement in accident rates which followed the random issue of electric cap lamps to native mineworkers in the Hercules Section of E.R.P.M. the previous year. Based on a 12 month trial period in which 250 000 shifts were worked with carbide lamps and (contemporaneously) 307 000 shifts with cap lamps, the incidence of major accidents (at least one day in hospital among men using carbide lamps was 1,15 accidents per 1000 shifts, while the incidence of minor accidents (requiring dressing only) was 11,52 per 1 000 shifts. The corresponding figures for men using cap lamps were 0,79 and 7,31 accidents per 1 000 shifts respectively, representing a reduction of over 30 per cent in both major and minor accidents. While these figures are obviously dated - only men using cap lamps were issued with hard hats, for instance - they do indicate a need for similar research today.

Jan 1, 1971

By M Hopkins, A Mutale, A E. Vidal da Silva

The Cliffs Nickel Mine extracts a narrow near vertical nickel vein using a mining method of underhand bench stoping with paste backfill. In 2014, at a depth of 400 m below surface, the Northern block of the mine began to experience squeezing within ore development. At first the deformation was localised, within 30 m of the stoping front, but later became pervasive extending across the Northern block and resulting in a hiatus in mine production. The global mechanism is a progressive pillar failure, where the inter-level pillars in advance of the production front could no longer withstand the induced load and progressively yielded. The local mechanism of failure was observed as crushing of the massive sulphide ore and ‘punching’ of the pillars into the ultramafic hangingwall exhibited as floor and sidewall dilation and unravelling of the mafic footwall. The cause of the global mechanism was attributed to a combination of factors, including: high overall extraction ratio, small vertical pillar heights between ore development, high stress in relation to the low rock mass strength, shallow stope front angle, and insufficient ground support capacity. Following the progressive failure, the remnant rock mass conditions across the northern block were severely degraded, with numerous falls of ground that led to a reassessment of the mine plan. Recovery of the Northern block started in 2016 as a staged process. Development of the safe recovery work methodology involved a number of considerations, such as: production sequencing, development access design, ground support, and development of specific procedural controls. The Northern block was then broken into smaller mining precincts based on tactical factors such as location, ease of access, scale of rock mass damage and nickel content. A specific ground support standard and work methodology are employed, while cycle sheets are used to ensure quality and completeness of work. Large intersections showing signs of deformation have either been bypassed or treated using Rocprops to maintain stability during stope production. This approach has been successful in safely regaining access and restarting production in areas that had previously been removed from the mining reserve.

Mar 15, 2021

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 12,564-acre portion of the 34,795-acre Rockhouse Wilderness Study Area (CA-010-029) in order to evaluate its identified mineral resources. The study area is located in Kern and Tulare Counties, CA, about 60 air mi northeast of Bakersfield at the south end of the Sierra Nevada. A review of the geologic and mining literature, and a field examination identified a turquoise and a gold prospect in the study area, and another gold prospect and a feldspar prospect within a mile of the study area boundary. Thirty-three rock and 16 alluvial samples were taken.

Jan 1, 1988

By John Norton

"This presentation will cover the physical properties of waste heat recovery. It is a two part presentation. The first deals with actually recovering the heat with new state of the art heat exchangers and applying that heat to the furnace combustion and the second part will cover what other processes you can enhance with this ""free"" heat. It will also talk about converting it to steam, hot air or electricity to be used or sold back to the utility company. The economics of various schemes will be reviewed. A brief discussion on State and Federal grants and subsidies will be presented.IntroductionThere are large quantities of wasted heat in the usual aluminum melting process. And, there are several techniques for reducing and/or using some of that wasted heat as you have seen. Any technique that can make use of wasted heat is a form of recovery. This can range from simply preheating aluminum billets prior to melting, to more complicated processes like air-to-air heat exchangers using the boiling and condensing characteristics of special fluids in “heat pipes.” The objective of this type energy recovery process is to move the wasted heat from the hot and dirty exhaust gas stream into some useful process.Waste Heat Recovery in the Aluminum Melting Furnace.There are considerations, of course:1) What might the value be of the recovered energy?2) Can the recovered energy be used within the process? Within the plant? Or by theneighbors?3) What is the capital cost?4) Is the recovery process complicated?5) Will it take additional staff?6) Will it cause additional downtime on the melting line?7) Will the operations staff need to be licensed?Ideally, the process will be simple and inexpensive, the recovered energy will be very valuable, and the whole effort will cause little distraction to the aluminum melting process itself. These would be ideal."

Jan 1, 2011

By José R. de Tenorio

The aim of the present work was to investigate the reduction process of MnO~FeO-Si02 slags by carbon-saturated liquid iron. The effect of the initial Mn content in the bath was explored. The initial Mn content was in the range of 0 up to 40 wt. %. The MnO content in the slag was kept constant at 40 wt. %. Tests were performed in laboratory apparatus. Samples of slags and bath were taken. In the first 5 minutes, it was observed a very strong reduction of FeO. This first step promoted a MnO-Si02 enrichment of the slag and a formation of CO bubbles, which increases the slag level. The increase ofMn content decreases the MnO reduction rate.

Jan 1, 1996

By Frederick M. Becket, Russell Franks

WideSpread experimentation has been conducted in recent years to devise a means of preventing intergranular corrosion in austenitic chromium-nickel steels of the 18 per cent chromium-8 per cent nickel type. Additions of titanium to these steels have been used commercially to overcome this dificulty, as advocated by Krupp of Germany, and the latest literature reference concerning improved details of this method is the article by Bain, Aborn and Rutherford.' Extensive work by the present authors has shown columbium also to be a particularly valuable agent for inhibiting intergranular corrosion. This paper does not deal with steels that are largely or wholly austenitic; it is limited to a discussion of the results obtained through the use of titanium and columbium in plain high-chromium steels. For many years titanium has been used commercially by some steelmakers as a cleanser, and to a lesser extent as a hardener, but then in greater percentages. The results of the work to be described disclose that titanium and columbium in proper Proportions act as effective softeners in the high-chromium steels. It is well known that chromium intensifies the hardening effect of carbon in steel; it imparts pronounced air-hardening properties within a rather wide range of chromium content; it provides increased ductility in steels of given strength and hardness; and it enhances resistance to corrosion and oxidation at elevated temperatures to a marked degree. However, in applications requiring a combination of some of these valuable properties great hardness is frequently a detriment rather than a merit. When the objective is a soft and ductile steel having optimurn corrosion resistance, the producer strives for a carbon content as low as commercially practicable. Despite these efforts some of the commercial high-chromium steels low in carbon present considerable difficulties during production, owing to their air-hardening properties, and in consequence the economic result is not favorable. A good example is found in the 5 to 6 per cent chromium steels employed chiefly in the oil-cracking industry. Sleels

Jan 1, 1934

By K. Y. Haramy

This report describes the development of an equation for predicting the crushing strength of 2-inch (5.08-cm) cubes of coal from point load tests made on irregular lumps. The equation was developed from point load and cube crushing strength tests performed on coal samples from six Western U.S. coal seams. For the six coals tested, the means of the point loads [(P)] in kg at failure were approximately proportional to the deans it the distances [(V)], in cm between the platen points for lumps in the 2 to 10-cm size ramie. This finding is at variance with results of tests on other rock types reported in the literature, which tend to show that P is proportional to D2 , as is normally assumed (in theoretical grounds. [The average crushing strength of a 2-inch (5.08 cu) cane for each type of coal was plotted against the log 10 of the slope of the P vs D plots, AP/AID . A straight line was fitted to these plots. The equation of the fitted line is cr = 1.72 x 10 4 10gK -2.10 x 10 4, where Cr is re estimated 2-inch (5. 08-cu,) cube crushing strength of the coal in psi and K is the scope of the straight line fitted to a plat of P v D for the same coal.]

Jan 1, 1982

By Camila Magalhães Gonçalves

O aço inoxidável ferrítico tipo 430 estabilizado com Nb, com e sem recozimento após laminação a quente, foi laminado a frio e submetido a recozimentos isotérmicos em temperaturas de 650, 700, 750 e 800°C por tempos variando entre 10 e 86400 s. A quantificação da fração recristalizada foi realizada pelo modelo de JMAK e pela microdureza ao longo do recozimento. A evolução da textura foi analisada via técnica de EBSD. Ocorreu o refino de grão após a recristalização, resultando em um tamanho médio de 8 mm. A temperatura de recristalização aconteceu a 750°C e esta teve maior efeito na recristalização que o tempo. Os expoentes de Avrami se situaram entre 0.8 e 1.2, significando nucleação em contorno de grão. A taxa de nucleação e de crescimento do grão diminuiu continuamente com o tempo. Em relação à textura, observou-se um aumento da intensidade das componentes (111)[121] e (111)[011] da fibra g e diminuição na intensidade da fibra a de deformação. Um modelo de cinética de recristalização do aço tipo 430 estabilizado com nióbio que leva em conta os processos de nucleação e crescimento foi obtido.

Jan 16, 2018

By S. K. Kawatra, S. J. Ripke, T. C. Eisele

It was determined by the authors that the water that remains in the filter cake after filtration in iron ore concentrators can contain several hundred times greater concentrations of calcium ions and other cations, due to surface chemical effects carrying the ions along with the water. Filter cake from two plants was analyzed. The water retained in samples of magnetite concentrate filter cake in Plant 1 contained 5088 ppm calcium and 5995 ppm magnesium, while the Plant 2 filter cake contained 231 ppm calcium and 119 ppm magnesium. These levels were dramatically elevated compared to the water that was removed from the concentrate by filtration for recycle to the plants (9 ppm calcium/15 ppm magnesium for Plant 1, and 11.9 ppm calcium/9.3 ppm magnesium in Plant 2). In addition to possible effects on agglomeration performance, the presence of these cations also affected the efficiency of filtration. In order to reduce the effects of these cations on filtration in Plant 2, carbon dioxide was injected into the slurry before it entered the filter press. This was found to increase filtration rates by up to 23.7%. Comparison of the results from the two plants shows that the concentrations of cations present in the filter cake will vary greatly from plant to plant, with correspondingly large variations in their effects on plant operations.

Jan 1, 2004

By Alfonso Rizo-Patrón

El presente trabajo describe la importancia de la explotación de los fosfatos de Sechura en la cuenca del Pacífico. Para ello, se evalúa el potencial de recursos naturales aprovechables en una infraestructura concentrada del área de Bavoyar y su implicancia en el aprovechamiento del potencial para el año 2000. Asimismo, es importante la planificación de un programa y una coordinación técnica adecuada de las realidades físicas, geográficas y geológicas de la cuenca señalada, así como la responsabilidad que ello implica.

Nov 20, 1972

By Jan M. Mutmansky

Simulation is a general term which commonly appears in the technical literature and which can have different meanings to different people. One interesting definition (9)* applicable in an engineering context is the following: "Simulation is the use of a model to study a problem." In most cases, the model referred to in the above definition is a simulation model constructed in a computer language and implemented on a computer in order to solve the problem under consideration. The application of computer simulation models to the study of problems in materials handling and earthmoving has been successful in the past. Generally speaking, this method has been used where the system to be studied has many variables and where the ability to predict the outcome of the system under different sets of conditions is difficult. The prime reason for using such a model is to evaluate the numerous likely ways of operating any particular system without the necessity of actually conducting full-scale field tests. The simulation model presented here is such an application made to the process of tunneling and, in particular, to the process of tunneling with a boring-type tunneling device. At first glance, the process of tunneling may not appear to be particularly complex and susceptible to study by a computer model. However, a close analysis of the tunneling process will reveal that it is rather complicated as a result of limitations placed upon the system by restricted space in the tunnel, geologic variations along the tunnel

Jan 1, 1972

By Michael J. Cruickshank

A workshop to examine recovery systems for selected strategic and critical materials in the U.S. National Seabeds for the National Defense Stockpile in the 21st Century was held in Hawaii September 26-28, 1991, sponsored by the National Science Foundation and the Marine Mineral s Technology Center. The National Defense Stockpile of critical and strategic mineral commodities is presently in a deficit position of more than 7.5 billion dollars. Current domestic reserves of some commodities are limited or nonexistent. As defined by the U.S. Bureau of Mines, "Reserves are select resources . . . which at the time of classification, can be mined at a profit." Occurrences of these minerals have been discovered offshore within U.S. jurisdiction. If the technology could be developed to convert these resources into usable ore reserves, our dependence on foreign ores could be greatly reduced. Preliminary estimates indicate that a ten-year program of ore reserves definition, with appropriate technical developments to demonstrate a recovery system, could cost less than half the amount authorized for stockpile acquisition in FY 1989 alone.

Jan 1, 1991

By I. Sedat Buyuksagis, Jamal Rostami, Ali Naeimipour

"Improving the safety of underground openings and optimizing ground support systems requires reliable ground characterization. This includes understanding the joints, discontinuities, and rock strength. Joint information can be obtained from borehole cameras, but measuring in-situ rock strength is very difficult. Use of borehole probes can be an ideal and efficient way to meet this requirement. This paper discusses the development of the Rock Strength Borehole Probe (RSBP) and presents the preliminary laboratory/field test. This device can be an accurate, flexible, quick, non-disruptive, and cost-effective alternative to estimate the rock strength inside boreholes in underground mines and tunnels. In addition, the scratch testing procedure in the laboratory by means of a newly developed miniature linear cutting machine is explained. Based on the results of these tests, two equations are developed to estimate the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of the sedimentary/metamorphic rocks. These equations, are based on testing 27 different sedimentary, igneous, and metamorphic rocks by full-scale scratch tests, including the cutting tests by a miniature disc. The results show a good correlation between the normal force and the compressive strength of sedimentary rock if the depth of the scratch is known. No significant correlation was observed for igneous rocks, due to the impacts of grain size.INTRODUCTIONEstimated rock mass properties are essential input for geomechanical studies and stability analysis for any structure constructed in or with rock. The availability of geological information is the crucial component of rock mass classification. One of the important parameters in evaluating rock mass properties is the intact rock strength. This parameter is usually measured by testing the core samples, obtained from exploration boreholes. These samples are subsequently tested in geomechanics laboratories. The test results offer limited information about the rock at the few boring locations despite all the efforts and costs. In addition, these results may not necessarily be representative of the behavior of the rock in the field as the test cannot provide the insitu condition of the ground."

Jan 1, 2016

By Renato G. Bautista, David C. Lindholm

The results of scale-up studies on a continuous, multistage horizontal mixer-settler extractor are presented. The chemical and mechanical system involves the separation of lanthanum from a mixture of rare earth chlorides using di(2-ethylhexyl) phosphoric acid as the solvent and dilute HCl as a scrub solution in a bench scale extractor. Each stage has a hold-up of 2.6 l. A single stage unit is utilized for scale- up studies. Results are obtained on four sizes of geometrically similar units, the largest being six times the volume of the original bench size. A unit operations technique is chosen so that mixing and settling can be examined independently. Variables examined include type of continuous phase, flow rate of inlet streams, and power input to the mixer. Inlet flow-rate ratios are kept constant for all tests. TWO potential methods of unbaffled pump-mixer scale-up are explored; the maintenance of constant impeller tip speed and constant power input. For the settler, the previously successful method of basing design on constant flow-rate per unit cross- sectional area is used.

Jan 1, 1977

By John M. Campbell, W. E. Portman

A series of correlating charts have been prepared to enable the field engineer to predict the amount of stock tank fluid produced by stabilization of first stage separator fluid. The charts shown are particularly convenient for estimating the relative effect of temperature and pressure in economic studies. Further work is planned to investigate the factors affecting stage separation' yo supplement this preliminary work. The direct correlation of separation variables is dictated as a convenience to eliminate the trial and error calculation necessary when using the standard flash vaporization equations. These are obtained by a material balance using the equilibrium vaporization ratio K, and have appeared in the following, or similar. form many times in the literature. where La = mols of any component n in the separator liquid Ko — equilibrium vaporization ratio for any component at separator pressure and temperature Fa = mols of any component n in the feed Vn = mols of any component n in the vapor V = total mols of separator vapor These equations may of course be effectively and accurately solved by use of digital and analog computers. However, these are not usually readily available in field offices and the need often arises for fast results during routine operational problems. Consequently, many methods have been devised in an attempt to simplify the basic calculation.2-14 The methods proposed are generally satisfactory, but do not eliminate trial and error methods and the necessity of subsequent calculations to obtain the answer in volume terms. The purpose of this work. therefore, was to develop accurate charts that would give the result directly in gallons. When using stage separation the recoveries would be lower than those shown, for stabilization usually gives about 95 + per cent recovery on the potential stock tank components in the separator liquid. The recoveries are shown in terms of a 14 psi Reid Vapor Pressure product which has a true vapor pressure of 14.7 psia at 98°F. Consequently, this product represents a stable stock tank liquid under normal storage conditions. To estimate natural gasoline re- coveries by stabilization the volume shown may be multiplied by 1.20 for 18 Ib RVP natural gasoline and 1.36 for 26 lb RVP natural gasoline. PROCEDURE The five analyses shown in Table 1 were chosen since they were representative of wellstream compositions often found and had almost the same propanes plus liquid content, expressed in gallons per 1,000 std. cu ft of wellstream. The distribution of the components though is widely variant. A temperature range of 0-100°F. and a pressure range of 200 to 1,250 psia was chosen inasmuch as most separations fall within these limits The K values used were modified values of those originally published by Katz and Hachmuth.' In the range chosen these have generally given good results when predicting fluid recoveries. The choice was somewhat arbitrary, for the authors' personal experience has shown that

Jan 1, 1957

By M. W. Lightner

IN 1947 the steel industry rebounded from its wartime effort and produced a record-breaking peacetime tonnage of steel ingots. During the first six months of the year the industry produced 42,000,000 tons of ingots and expected to produce 85,000,000 tons for the year. With a rated capacity of some 91,000,000 tons, production was at a rate of about 93 per cent of capacity. Credit must be extended to the steel producers who have maintained this steady state of operations while faced with many problems, not the least of which was a continued shortage of satisfactory scrap. Furthermore, the steel industry started a record-breaking peacetime expansion program at a total cost of more than $1,000,000,000. This program will increase the ingot-making capacity of the country by 2,500,000 tons and should be completed in 1948.

Jan 1, 1948

By E. J. Gleim

[of- ac tore affecting the e -success of recent conveyor miningsystems forLt. extraction. 1 GL C ,_tfreedom shoot &apos;_)`u 2--ethe.1 is coal while e en othershot firers re:7 t _e&apos; _U-tin , w J, e coal .Z- 311.ing States conveyors because ;-.;lax .ca requires thatblasting be limited to when c .. men os. _o tend neces¬sary officials 1 s . re out c-z ,r 7t ...y e:e l z<: woes no t a -¬#to 1 C" such restriction on blasting conveyor miningbeen extendedWhere ere t ere. re no _ c: t&apos;_ _c tit-----! . kind cutlasting;,1CL?; C&apos;. _ z)carried anI-7LC. AT continuouslyHowever, unless et._&apos;0:, precations are taken under r&apos;t e , accidents, n is or such, as111 electricity r 1C- from.J--_,._.1t ,° =&apos;1?without usingholes, as well as numerous-o _&apos;1&apos;-1 -= e troublehe record of mineexplosions (some of themSo so _C&apos;_ °:&apos;,v 0f rock- dusting]

Jan 1, 1941

By M Jacobs

This abstract discusses a heap leach copper mine that was failing to perform and as a result was not meeting targeted production. The mine had numerous technical challenges including: high water inflows, low levels of geotechnical monitoring, performance issues with mining, resource model and grade control reconciliation issues, and unexplained low levels of performance from the heap leaching operations. A team from various organisations with specialist skill sets including: a forensic accountant, the owner’s representative and a mining engineer, was arranged to visit the site. The task was to investigate the situation and determine what could be done to turn the performance of the mine around. After an initial assessment in late 2018, efforts were directed to better understanding the operations and improving the performance of the site through preventative management. A key part included the creation of production forecasts that could be achieved that would help restore confidence in the operations. Uncertainty in the mine achieving production forecasts and the performance of the heap leaching operations were contributing to the decline of the operations. Investigations uncovered the fact that while the resource model could reliably predict total copper, a lack of sequential leach data meant the accurate prediction of soluble and insoluble copper species, both important for heap leaching, was difficult to do with any degree of certainty. The crushing and mining contractors also appeared to have suffered somewhat from a lack of management by the owner’s team and performance had affected the production of copper. Collaboration and management were used by the team to understand and stabilise the operations. Ongoing collaborative efforts by the management team, site personnel and contractors resulted in a positive outcome for the owners and their mine – and could at yours.

Jun 22, 2022

By L. R. Chimimba

"The Trojan nickel deposit occurs within a pile of ultramafic lavas subjected to a lower amphibolite grade of metamorphism. The lavas form part of the Upper Greenstones (Bulawayan Group) of the Mazoe greenstone belt. The nickel mineralization occurs as disseminated, massive and near-massive sulphides. The massive and near-massive ore occurs along the basal contact of the serpentinite units and is overlain by the more abundant disseminated ore, which occurs within the serpentinite. The main sulphide minerals are pyrrhotite. pentlandite and chalcopvrite. Minor amounts of millerite and pvrite are present. The Ni : Cu ratio in all three types of ore averages 15:1.The intercumulus nature of sulphides in the near-massive ore and similar textures occasionally seen in the disseminated ore indicates a magmatic origin of the mineralization. The basal position of the near-massive and massive ore suggests that the sul­ phides settled out under gravity during the emplacement and crystallization of a peridotitic magma. The deposit has been deformed and some of the primary massive ore has been remobilized into veins and breccias. The disseminated mineralization now occurs mainly as blebs of sulphides intergrown with silicate minerals or as stringers of sulphides between foliation planes in the serpentinite."

Jan 1, 1984

By Daniel Roy, Danielle Bouffard, Antoine Berton, Simon Gariépy

Commissioning a mineral processing plant has always been a challenging task. The process includes pre- operational verification, dry and wet commissioning, and a gradual ramp-up to full production, all of which must be executed within the shortest possible timeframe, requiring numerous highly interdependent tasks to be conducted concurrently. This phase is under scrutiny by shareholders, corporate management, and other stakeholders who are keen to see a return on investment as the operation starts yielding results. Despite extensive documentation in the literature highlighting its significance, the impact of the commissioning phase remains underestimated in contemporary mining projects. This paper provides an overview of the commissioning process and its associated challenges before focusing on a critical success factor: building a dedicated commissioning team with the required competencies and personality profiles. The roadmap to achieving an efficient plant start-up is outlined. Drawing on over 15 years of experience with more than 20 concentrator commissioning and start-ups, a general framework is presented to maximize success. This method emphasizes the crucial role of the operation and metallurgy team in supporting these projects. Finally, insights from Soutex’s involvement in multiple start-ups are shared, offering lessons learned that emphasize best practices and challenges encountered in expediting the ramp-up process while maintaining high Health, Safety, and Environment (HSE) standards.

Feb 1, 2025