Search Documents

By J. E. Nesset, F. Rosenblum, J. A. Finch

"The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to highly reactive and potentially hazardous to both humans and infrastructure. It is essential that there be a reliable test methodology that can measure and categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral mixtures making it difficult to predict their self-heating behaviour a-priori based on mineralogy or with a simple “snapshot” test. Furthermore, self-heating behaviour will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to measure and reliably predict the latent self-heating hazard of a sulphide material. Several of the methods were tested and compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.INTRODUCTION Sulphides as well as other materials (coal, wood chips, hay, powdered milk, to name a few) that are stockpiled in an air atmosphere may undergo oxidation reactions which can result in the evolution of heat (Beever, 1984) (Hudak, 2002) (Blanchard, 2007). If the rate of heat generated exceeds the rate of heat dissipation, the stockpile temperature will rise, potentially leading to “hot spots” in the most reactive areas, and possibly even fires. The heat generation rate, the “self-heating” rate, depends on many factors such as the type and composition of material, particle size, moisture content, oxygen availability, ambient temperature and humidity, and of prime importance, the extend of prior oxidation, or more specifically, the presence of oxidation products. The desire of operators that mine, process or transport sulphide-bearing materials with a potential for self-heating is to have an accepted and reliable method for evaluating and quantifying the potential hazard of their material. The challenges are how to best measure the self-heating properties of given samples, and based on results, predict the behaviour of the bulk material over time and in-situ. Generally, when evaluating a given material one derives the self-heating characteristics of that sample at the time and under the conditions of testing, which will be referred to as a “snapshot test”. If that material is invariable, i.e. it will not change its response over time, then it may be considered to be a “predictive test”. However, if as a result of continuing oxidation or other changes, the material becomes more or less reactive with time, then a “snapshot test” is unreliable with respect to predictive ability."

Jan 1, 2014

By E. G. Baglin

As part of an effort to decrease U.S. dependence on imports of critical and strategic metals, the Bureau of Mines investigated three leaching methods for extracting the base metals and recovering platinum-group metals (PGM) from matte prepared from Stillwater Complex flotation concentrates. Because of a limited supply of natural material, synthetic matte of composition similar to matte prepared from natural concentrates was used to devise the extraction sequences. The validity of the sequences was verified with matte prepared from Stillwater concentrates. In two-stage matte leaching, first-stage H2S04 leaching extracted 99 pct of the nickel and iron from the matte but negligible amounts of copper and PGM. Second-stage oxidative leaching with Fe2(S04)3 or FeC13 solubilized more than 98 pct of the copper and no precious metals. Sequential leaching, in which acid and oxidizing lixiviants were added sequentially to the matte without an intervening filtration step, extracted 99 pct of the Fe, Ni, and Cu. A roasting-leaching technique, in which the residue from first-stage leaching was roasted between 360° and 500° C before a second leaching with H2S04, solubilized 98 pct of the copper. The three leaching methods yielded high-grade PGM residues containing more than 98 pct of the PGM in the matte.

Jan 1, 1982

By E. S. Schubert

Keywords: co-generation, furnace CO-gas cleaning, disintegrator scrubber, Theisen In a closed, electric, reduction furnace, no oxygen enters the furnace from the surrounding environment. The off-gases are thus not ?burnt? and therefore contain a considerable amount of CO and H2. Traditionally these gases have been captured and burnt in a flare stack. Recent developments have led operators of such furnaces to revise this strategy and to consider utilising these gases as a fuel for gas-fired generator sets to produce electricity, thus becoming more energy efficient. On 31 March 2010 the new emission standards, in accordance with the Air Quality Act, Act 39 of 2004, were promulgated. The minimum emission standards according to the act require that the particulate matter emissions from the primary fume-capture systems on closed furnaces for ?new plants? in ferroalloy and calcium carbide production not exceed 50 mg/Nm³ and 25 mg/Nm³, respectively. By implementing co-generation, the producer automatically complies with the new environmental emission standards for an off-gas. As much as 30% of the electrical power cost, which is set to double in the near future, can be saved by partly generating one?s own electrical power. In December 2010, the National Treasury published a discussion paper for public comment, one entitled ?Reducing greenhouse gas emissions: The carbon tax option?. Irrespective of how the tax is finally implemented, it will result in an increase of production costs in affected industries. This paper focuses on the characteristics of a furnace-off-gas cleaning system for closed ferroalloy smelters, characteristics that meet the requirements of both reducing solid-matter emissions and operating a safe and reliable gas plant.

Jan 1, 2011

By Hui Wang

With the great increasing use of nickel metal hydride batteries recently, the waste of this kind batteries have been paid for close consideration. For the main reason that the waste of the batteries contained precious metals and lanthanide which cost great lose. This paper introduces the pyrometallurgical process of recovering nickel and cobalt from the waste of the nickel metal hydride batteries. Particularly, the waste for the process was from factory during the producing program. The use of designed solvent to divide nickel and cobalt in melted state from the waste is described. Also, the result of the nickel and cobalt and melted gangue that mainly consist of lanthanide oxide are included in details. The aim of the paper is to find out a simple and feasible way to reuse waste from nickel metal hydride batteries.

Jan 1, 2009

By Andy Fortin, Jeet Basi, Simon Hille

Goldcorp’s Eleonore mine is situated in Ell Lake area in the northeastern part of the Opinaca reservoir in the James Bay region of Quebec. The design of the 7000 t/d process plant includes crushing, grinding, bulk sulphide flotation, separate concentrate and tails leaching and detoxification circuits and residue handling. Detoxified flotation tails are thickened and filtered. A portion of the filtered tails are blended with the thickened detoxified sulphide concentration for paste backfill. The remaining filtered tails are trucked to the waste management facility. This presentation will describe the challenges faced with the commissioning and subsequent ramp-up of the flotation tails filter plant and the successes achieved by the multi-discipline team at Eleonore.

Jan 1, 2016

LANDSAT imagery has renewed interest in linear features first recognised by E. S. Hills in a physiographic model of Australia. Certain of these lineaments are aligned with structures which control mineralisation.Lineament guidelines are potentially useful in many poorlyexposed areas if they can be recognised early enough in exploration and drilling programs leading to mine development.A case history based on the Charters Towers Gold Field indicates that lineament guidelines can be established early enough to guide development ofnew mines. The position of the Charters Towers Lineament was known as early as 1956. Subsequently, more detailed publications identified and classified associated lineaments which provide intersections correlated with gold occurrences. The discovery of a significant orebody at one of the most prominent lineament intersections came in 1975. Mine drilling has confirmed the influence ofintersecting structural trends indicated by lineaments but not by previous regional mapping.Recent gold discoveries south of Charters Towers lie in a grid of prominent lineaments. The development of mines about Charters Towers will provide additional understanding of relationships between centres of mineralisation and lineament intersections. This understanding may in future be sufficient to encourage exploration for a new generation of concealed gold deposits in northeastern Queensland.

Jan 1, 1986

As it is probable that a large proportion of the members of the Institute attending this meeting are connected with the metalliferous side of mining, the writer thought that, as coal and coke are required for various purposes in considerable quantities by their companies, some particulars of the coal industry might be of interest, especially when visiting such an important coal-mining centre as Newcastle. It is proposed to deal with the matter from the mining and economic point of view, as the geology has been so well and exhaustively dealt with in various publications referred to in the bibliography at the end of this paper. In the immediate vicinity of the city of Newcastle the collieries are gradually being abandoned, and during the past few years the Wickham and Bullock Island, Stockton, Hetton, Newcastle Coal Mining Company's "B," and the Australian Agricultural Co's Sea pit, have disappeared from the coal-producing list of collieries. AIl of these collieries worked the Borehole seam, from which, up to date, the largest quantity of coal has been produced in the northern district.It is the bottom seam of any present commercial value in the Upper or Newcastle coal-measures, and although the coal-in this seam has not been entirely 'exhausted in the collieries referred to, they have been abandoned for various reasons. For example, although about 60% of the seam (18 to 20 ft. thick) was left in the workings in the form of rectangular pillars under the city of Newcastle, this was not sufficient to 1?revent'the subsidence which took place about twelve years ago.Again, large quantities of coal in the Borehole seam have been left to protect the shipping arrangements at the Dyke, and other...

Jan 1, 1918

By Bowang Xiao

Recently more and more attentions are paid to high pressure hydrogen quenching (HPHQ) for its advantages such as environmental friendliness, low distortion, etc, compared to oil and water quenching. In HPHQ process, heat transfer coefficient (HTC) usually varies from part surface to surface because of the intense variation of gas velocity around the part. This article studies the effect of HTC distribution on part distortion after HPHQ and shows that finite element simulations considering HTC distribution predict different distortion from these without considering HTC distribution. It is also pointed out in this article that HTC distribution can be optimized by adjusting part orientation and HPHQ condition so that part distortion is minimized.

Jan 1, 2010

Pillars in underground limestone mines are required to support the overburden and provide a safe, stable working environment for mining personnel and equipment. Pillar stability was assessed by the National Institute for Occupational Safety and Health in underground limestone mines in the Eastern and Midwestern United States. It was found that current mine layouts have been successful in providing support to the overburden, while a small number of isolated pillar failures were observed. The stable pillar layouts and failed pillars were plotted on a chart that demonstrates the relationship between pillar width-to-height ratio and pillar stress. The results show that pillar failures occurred at the lower range of width-to-height ratios and can occur at relatively low stress levels. Zones indicating the potential risk of pillar instability are shown on the chart, based on hazards associated with the onset of rib spalling, large angular discontinuities and unconfined pillars. The chart can assist limestone mine planners to evaluate potential instability in current or new pillar layouts that are similar to those included on the stability chart.

Jan 1, 2008

By M. Hopf, E. Rossouw

Keywords: Pyrometallurgy, furnace, copper coolers, freeze lining, monitoring, Saveway The use of water-cooled copper components as sidewall elements of submerged arc furnaces and other pyrometallurgical applications has become increasingly common. The high cooling efficiency of copper has made it possible to increase the service life of furnace refractories when compared to conventional refractory linings. However even the self-healing effect of ?freezing? worn areas of the lining does not necessarily protect the copper coolers against wear or corrosion completely. In order to avoid furnace explosions, various methods have been used to monitor the wear of coolers. Unfortunately, these have not been able to consistently identify localized wear. Thos Begbie (South African) and SAVEWAY (German) jointly developed technology to embed a line sensor into the copper cooler during the casting process. This system allows an exhaustive monitoring of the copper cooler. A SAVELINE sensor is placed inside the copper-cooling panel between the water-cooling passage and the hot face of the panel. The sensor follows the meandering shape of the cooling water channels. In the first instance, the sensor provides analogue information as the thickness of the copper reduces. Secondly, this wear signal will be confirmed by a signal of interruption if the sensor is washed away. Because of the structure of the sensor, a self-diagnosis is possible and indications can be confirmed (double proofed). Subsequent to the manufacture of some test pieces, coolers for a large submerged arc furnace were manufactured. The sensorized coolers have been installed at the intermittent surface (slag line) where the largest amount of corrosion has been encountered. The system has been operating since December 2005 in what is considered one of the largest submerged arc furnaces in South Africa.

Jan 1, 2006

By Ronald E. Heuer, Debra L. Virgens

INTRODUCTION Behavior of clay soils in response to tunneling is reasonably well understood by reference to the tunnel stability factor NT = Pz/su (Peck, 1969; Heuer, 1974). With this analysis tool, care must be taken to use a value of clay shear strength which represents the actual mass strength, considering such factors as slickensided fissures often found in stiff and hard clays. Behavior of clean sand and gravel soils is also reasonably well understood. Above the water table these soils must be assumed to act as running ground unless they are known to have significant cementation or have a very dense and angular interlocked grain structure. Below the water table they must be tunneled using some form of groundwater control such as dewatering, grouting, freezing, or internal fluid pressure in the tunnel such as compressed air or a slurry tunneling machine. The internal fluid pressure must approximately balance the external water head. Without such precautions these soils behave as flowing ground and may yield large volumes of water flow into the tunnel. A wide range of very fine sand, silty sand, cohesionless silt, and clayey sand soils exist in nature in a variety of geologic environments. The behavior of these soils in response to tunneling, and guidelines for anticipating their behavior, are not well described in the literature. Because of their content of fine particles, these materials may behave as if they initially have appreciable cohesion and moderate to low permeability. They may exhibit significant standup time, and require tunnel internal fluid pressure (compressed air or slurry pressure) less than the full external water head. It is important to be able to estimate the behavior of these soils when planning construction methods. For example, if the external water pressure is 140 kPa (20 psi), but soil stability at the tunnel face can be achieved as a compressed air pressure of 80 kPa (12 psi), a large cost savings may result.

Jan 1, 1987

By K. Lundholm, M. Andersson, L. Nevatalo, Å. Holmström, L. Hedström

"Several copper deposits have the arsenic bearing minerals enargite (Cu3AsS4) and tennantite (Cu12As4S12). Since this mineral contain both arsenic and copper, it is not possible to remove the arsenic by selective flotation. Partial roasting is a method to clean the concentrate from arsenic and thereby produce a suitable raw material for the copper smelter. Also mercury is commonly found in copper bearing minerals. In the partial roasting process both arsenic and mercury are volatilized, while part of the sulphur is used as energy during the roasting. This gives a calcine suitable as feed to a smelter, much like an ordinary copper concentrate. A typical analysis of calcine would be: S content 18–22%, As content below 0.3%, Cu content – not affected, grain size – not affected. However, if the concentrate contains mercury, the mercury will be volatilized during the roasting process. This will lead to very high mercury contents in the subsequent process of sulphuric acid, unless the SO2-rich process gas is pre-treated by the Boliden/Norzink process that recovers mercury as calomel, Hg2Cl2. The volatilized arsenic in the gas phase can be recovered either by dry or wet methods. However, one problem is that arsenic also contaminates the fine grained calcine dust that is captured downstream in the gas cleaning system. The calcine dust contains valuable metals such as copper, gold and silver that needs to be separated from the arsenic. The ultimate aim is to stabilize the recovered arsenic as a compound with minimum impact on the environment and recover the valuable metals. By using wet recovery methods it is possible to selectively precipitate copper, gold and silver as sulphides while arsenic is kept dissolved in the liquid. The precipitated metal sulphides can be mixed with the calcine and sent to the copper smelter. The dissolved arsenic is sent to effluent treatment and is further treated in Outotec ferric arsenate precipitation process, where arsenic is precipitated as the stable compound basic ferric arsenate, formula FeAsO4·xFe(OH)3. All concentrates containing arsenic are unique and the process design of a roaster plant must be based on relevant process data. The process data is collected during tests in lab scale and pilot scale, where the influence of critical process parameters on the quality of calcine is studied. The ability to run tests both in lab scale and pilot scale is crucial to the development of the correct roasting process. Outotec is well equipped for this."

Jan 1, 2014

By Eduardo Pimenta de Melo, Rambabu Pothina, Rajive Ganguli

Sensors are everywhere in the mining industry, with sensor information being used to monitor and operate processes. Therefore, when sensor information is wrong, economic losses can occur. Unfortunately, sensor errors are usually not detected till they become large. This is problematic as most calibrate their sensors no more than once a year (Beamex, n.d.). Using principles of data mining, where all relevant information is tapped to glean hidden information, Pothina [8] designed an algorithm to detect errors in temperature sensors in gold stripping circuit in Pogo mine, Alaska. This paper continued his work by analyzing the behavior of the algorithm on baseline data and testing the algorithm in new data and under more rigorous conditions. It also made a change to the algorithm. The modified algorithm performed very well in the new data. It also worked well under the new error conditions. Three types of errors were seeded, a fixed additive error (+ 2%), a fixed subtractive error (− 2%), and a noisy, normally distributed error, with a mean value of + 2%. Artificially seeded errors were detected within about 20 gold stripping cycles. Inherent bias in operation impacted algorithm performance by increasing the number of cycles needed to detect errors. This paper reinforced Pothina’s [8] conclusion that when data mining approach is used, sensor errors can be detected even when they are pretty low. Significant economic losses can thus be minimized.

By N. E. Lehman

Cordilleran metamorphic core complexes in the southwestern United States are areas where middle to late Tertiary low-angle normal faulting has uncovered rocks that were at temperatures sufficient for mylonitization during the early part of Tertiary extensional faulting. Large-displacement low-angle normal faults that separate upper-and lower-plate rocks in metamorphic core complexes are termed detachment faults. The significance of Tertiary detachment faulting in the Basin and Range Province has only become apparent in the past 6-8 years, and the association of mineral deposits with detachment faults has only been recognized in the past few years as well. Crystalline rocks below detachment faults have typically undergone chloritic alteration and brecciation over a distance of a few to a few hundred meters below the fault surface (Fig. 1). Chloritic alteration and brecciation overprinted mylonitic fabrics formed during earlier ductile shearing along the down-dip projection of detachment faults. Rocks that underwent pre-Tertiary ductile deformation and prograde metamorphism were subjected, in rapid succession, to middle to late Tertiary mylonitization, brecciation and chloritic alteration, microbrecciation immediately adjacent to the fault, and subaerial exposure. Lower-plate rocks thus experienced rapid decompression and cooling as a result of tectonic denudation and isostatic uplift (Wernicke, 1981; Davis, 1983; Davis et al., 1986).

Jan 1, 1987

This publication summarizes the Bureau's activities as part of a study of the Juneau Mining District (JMD) during the period 1984-1988. The objectives of the program were to identify the type, amount, and distribution of mineral deposits in the district, determine ore reserves, study beneficiation technologies for the ore, make feasibility studies, and address economic and legislative effects on mineral development. The JMD study was a cooperative study involving the Bureau and the Alaska Division of Geological and Geophysical Surveys (ADGGS). Over 30 employee-years were spent by the Bureau on this project. Bureau investigations in the JMD consisted of a district-wide investigation of industrial materials in addition to site-specific investigations of precious and base metals in five subareas. During the 4 years of the JMD study, more than 300 areas, mines, prospects, and occurrences were visited, which contain gold, silver, copper, zinc, lead, nickel, cobalt, tungsten, molybdenum, chromium, and platinum group metals (PGM). More than 59,000 feet of underground workings were mapped and sampled. More than 5,500 samples were taken; one diamond drilling program and three geophysical surveys were completed. An up-to-date and complete mineral data base for the JMD did not exist prior to this study. The JMD study, which coincided with a tremendous increase in mineral interest and activity in the district, has proven to be valuable to both the minerals industry and land management agencies. The discovery of two new mineral occurrences and compilation of data on known mines, prospects, and occurrences have aided industry activity in the region. The study enabled timely data to be available to land management agencies at the Federal, State, and municipal levels.

Jan 1, 2012

By L. W. T. Weitzel

"This paper reviews the Falconbridge- SMRQ’s Raglan project in northern Quebec and the process that was used in developing its current long-term mine plan. Challenges were many and not only limited to the longevity of the project, numerous ore deposits (both underground and open pit), and a 40 km property strike length. As a result of its remote northern location, other factors such as progressive reclamation, leachable mine waste, water treatment, and waste management were also part of the plan. A combination of modern planning tools were used to formulate the plan including DataMine, Mine 2-4D, AutoMod Simulation, and an Excel-based financial spreadsheet to bring the total plan together. The focus of the paper is to show the complexity of modern mine planning and associated economic modelling of mine processes. IntroductionThe Raglan project is located 1660 km directly north of Quebec at the northern tip of the Quebec Peninsula in Nunavik. The main property is 40 km in length stretching from the Donaldson airport area at the eastern edge of the property to East Lake at the western edge. The Deception Bay port is 90 km north of the main complex/mill situated at Katinniq which lies approximately in the middle of the property (Fig. 1). The mine processes 1 000 000 tpy of ore from both open pit and underground sources. The mill is forecasted this year to produce more than 150 000 t of concentrate grading more than 18% nickel. All personnel and critical cargo are transported to the site via a company-leased 737 jet from Rouyn-Noranda where the main administration office is located. The majority of cargo is shipped to the site via Deception Bay from Quebec and on the return trip, nickel concentrate is shipped back. From Quebec, the nickel concentrate is sent by rail to the Falconbridge smelter in Sudbury and on the reverse rail haul, nickel matte from the smelter is sent to Norway via Quebec."

Jan 1, 2003

By J. R. P. Aguirre

Minerales Monclova, S.A. de C.V. (MIMOSA) is owned by Grupo Acerero Del Norte (GAN). This company has 4 underground coal mines and 1 open pit to feed it?s steelmaking facilities located in the city of Monclova in the North of México in the state of Coahuila. The current underground mines are Mine 3, 5, 6 and 7 and the future projects are Mines 8 and 9. In the last years Mines 2 and 4 have been closed because they finished their coal resources. The remaining mines have bigger production and developments requirements in order to accomplish the goals of the company. The mines have been working in deeper and gassier areas. These conditions have required improvements in the ventilation design and methane control systems for all the mines. In some cases the ventilation of some of the MIMOSA?S mines has been increased 80%, and besides this, an intensive methane drainage program has been applied using horizontal in-seam boreholes and gob wells. The short-term ventilation plan includes the construction of 3 new vertical shafts with 5 and 6 meters diameter for Mines 5, 6 and 7 and the purchasing of bigger new main and backup fans for each one of these mines. One of these vertical shafts and the purchasing of the first 2 fans is already in process. This paper will explain the evolution and results of the ventilation and methane drainage systems in MIMOSA and the ventilation planning for the future years.

Jan 1, 2009

By L. M. Southwick

"The history of extractive metallurgy is replete with examples of commercializing new processing technologies. The successes are widely reported, but failures seldom are. This is unfortunate, for usually we can learn more specifics on how to succeed in technology development by studying and thoroughly understanding their failures. Frequently one encounters a red herring that caused the whole effort to fail. A thorough and objective due diligence up front would have identified those red herrings and prevented the pursuit of a bad idea and the resulting destruction of capital. Due diligent analyzes performed before construction of three such bad ideas will be discussed. One is an EAF dust process, which pursued the red herrings of a poor understanding of the business, a naïve view of past experience, and false confidence in the technology. Another will examine the effort to commercialize a new pressure copper leach process that followed the red herrings of inadequate testing of the raw material, application of processing conditions that were inherently unsafe, and an improper assessment of the inherent advantages of past developments. The last is an alternative iron-making process, where the red herrings were incomplete and superficial assessment of prior pilot plant and demonstration plant tests, an assumption that the commercialization model of “build it and we will make it run” was viable, and a technology whose technical fatal flaws had already been identified. Unfortunately, capital destruction often also closes the window to more intelligent pursuit of technology development. TECHNOLOGY COMMERCIALIZATIONThe development and commercialization of new technology is a vital part of keeping industry profitable, able to deal with new sorts of feed stocks and current with economic, product, operational and environmental requirements. This is a difficult task in the best of times, and can be compounded when the developers become enamored of a particularly favorable characteristic of the project or of the product. These “red herrings” divert project focus away from the arduous path to success and, in the end, result in project failure."

Jan 1, 2012

By Jacob Chacko

The east span of the San Francisco-Oakland Bay Bridge (SFOBB), which is one of the most heavily traveled bridges in the world, will be replaced due to seismic safety concerns. The majority of the new bridge will be founded on large-diameter (1.8 to 2.5 meters), approximately 60- to 100-meter-long pile foundations The large-diameter steel pipe piles and soil conditions are similar to those used/encountered in many offshore structures. Thus, the design methods used are based on site-specific modifications to the procedures recommended by the American Petroleum Institute rather than the conventional procedures that have been formulated and used for the design of much smaller piles. Pile foundations will experience their maximum loads during the design earthquake. For the Safety Evaluation Earthquake, tension loads of up to approximately 80 to 90 meganewtons (MN) and compression loads of up to approximately 120 to 140 MN were calculated. Due to the economic importance of the SFOBB and the consequences of catastrophic failure in both economic and human terms, the design and analysis of the pile foundations supporting the bridge consider a number of aspects of pile-soil behavior that are normally ignored. Those aspects include: 1) the effects of consolidation and setup, 2) the behavior under dynamic loading, 3) the losses of resistance under cyclic loading, and 4) the load-settlement behavior of the piles under severe cyclic loading conditions. Since the treatment of complex aspects of pile foundation behavior is not codified in any guiding documents, several project-specific methods were developed for design and analysis of the foundation piles.

Jan 1, 2002

By Steve Kral

The mining industry in Colorado faces the same problems the industry faces throughout the United States and the world — record low commodity prices and increasing regulatory and environmental restrictions that seemed designed to curtail mining activities. Despite those obstacles, the mining industry in Colorado still contributes about $8 billion annually to the state’s economy in the form of base and precious metals, industrial minerals, coal and associated service businesses and jobs. So the 300 attendees at the102nd National Western Mining Conference felt reason-ably positive about the industry in their state. The meeting is the Colorado Mining Association’s annual conference and was held at the Broadmoor Hotel in Colorado Springs in November. The theme was “Mining in the New Millennium — Achievement + Innovation = Survival.” Experts from Colorado’s mining industry and abroad discussed the challenges faced by the mining industry as it enters the new millennium. They offered insights into how the industry will operate during the early years of the 21st century and how it will survive low prices and increased regulatory restrictions.

Jan 1, 2000