Search Documents

By Pedro Lilienfeld

This report describes a program to develop, design, fabricate and subject to environmental testing three prototype collection-sensing devices of an eventual mining-machine mounted automated monitor for the measurement of the respirable fraction of coal mine dust to determine both short-term as well as average mass concentrations over typical 8-hour shifts. The design of this instrument is based on collection by filtration and mass sensing by beta-radiation attenuation. The emphasis of this development program was to evolve a rugged, stable and reliable collection-detection head compatible with the environment to which An eventual monitor will be subjected. Laboratory testing of this prototype instrument was performed over a representative range of temperature, humidity, dust concentration and composition, shock and vibration. The results of this testing program indicated that the operation of the prototype version His compatible with these environmental conditions and that further development of this configuration into a field operational device is justified.

Jan 1, 1977

By Klaus Pronold

Once installed rolling mills can look forward to a long life. Around 40% of the 140 conventional hot strip mills presently in operation were built between 1960 and 1970. 17 of the 29 CSP®-plants were commissioned before the year 2000 and have automation platforms that are obsolete and/or have outdated rolling technology. Keeping pace with the market requirements is an ongoing challenge for producers of flat steel. It is a real balancing act keeping production facilities performing at necessary levels, safeguarding the investment and keeping outage periods to a minimum. To overcome these demanding factors and strike the right balance allowing for the production of higher grade steel that meets the current market price the installation of mechanical equipment as well as automation platforms and process technology must meet the latest technology standards. Being discussed in this paper are the different motives for modernizations along with their impact on project handling and commissioning philosophies. Experience gained during recent modernization projects in the field of flat steel rolling relating to Steckel / plate mills or current CSP® modernizations will be shared and demonstrate that each modernization has its own individual solution. Specific strategies are explained to help optimize production, increase plant agility and maximize the return on investment.

Aug 17, 2017

By Youjun Tao

Falcon centrifugal gravity separation tests were conducted to study desulfurization and de-ashing performance with different size fractions of a high-sulfur Chinese -0.5mm fine coal in a dense medium. Performance indicators such as combustible recovery, ash and sulfur rejection, and desulfurization efficiency were used to evaluate the separation efficiency. The results show that for -0.5 mm coal particles, all performance indicators except ash rejection are higher for the Falcon concentrator than for flotation. More specifically, for the +0.125 mm size fraction, Falcon centrifugal separation produced better ash and sulfur rejection performance than froth flotation. However, the Falcon concentrator also showed higher combustible recovery but lower ash and sulfur rejection than froth flotation for the -0.125 mm size fraction.

Aug 1, 2013

By Sander Mul, Michael Brandner, Armin Paar

Graphitic HSS roll grades such as ESW’s brand VANIMO can be considered as the latest developments for the last finishing stands in hot strip mills. These roll grades are developed on the basis of the alloying concept of (Carbide Enhanced) Indefinite Chill work roll materials. During the development of VANIMO, the amounts and types of carbide forming elements were increased and adjusted into the direction of cast HSS roll grades. The microstructure of graphitic HSS roll grades therefore consists of tempered martensite, cementite and several different carbide types as well as a well-defined amount of free graphite. The main purpose of graphitic HSS roll grades is to combine the high surface quality of Indefinite Chill alloys as well as the high wear resistance of HSS roll grades. Several systematic steps were taken to increase the wear performance from Carbide-Enhanced Indefinite Chill grades to the more advanced VANIC grade and further on to the highest alloyed roll grade VANIMO. In every development step, the surface quality of the roll grades was carefully monitored. The decision to invest in new testing equipment at ESW’s plant was driven by the wish to see microstructural effects of different alloys in a macroscopic dimension. Usually samples are taken from cast rolls and investigation is done in comparably small areas compared to the total surface of a roll. Rolling of strip is done with the entire barrel, so effects of alloy and microstructure can appear anywhere on the barrel surface. To ensure better understanding and deeper knowledge about influences of alloying trials we decided to install the last version of LRI (Lismar Roll Inspection). LRI includes the latest technology of Eddy Current with an enormous resolution. Depending on the formation of carbide precipitations, carbide network as well as matrix and free graphite, the EC test can detect smallest differences. The possibility to analyze the different results of EC and UT surface wave inspection will be discussed. A few examples of surface effects in the mill application will be discussed and improvement strategies explained.

Oct 1, 2019

By Congcong Chen, Bo Ma

When assessing the safety of a tailings dam, the constant weight method (CWM) is one of the most commonly used methods. However, when the evaluation indicator value suggests serious defects, the evaluation value is often inconsistent with the actual situation. To address this issue, the variable weight method (VWM) is introduced to assess the safety of the tailings dam. Initially, a three-layer indicator system for dam failure safety assessment is built, and individual indicator values are divided into four grades. Then, an appropriate state variable weight function is constructed and relevant parameters are determined. Finally, a case study is illustrated to verify the effectiveness of the model. The assessment results of the VWM more closely represent the actual situation than that of the CWM, which is more helpful for decision makers and technicians to take scientific and reasonable precautionary measures, thereby improving the safety management of the tailings pond.

Oct 8, 2022

By R. M. Quinlan

The coal industry in the United States has undergone significant economic changes during the past six years. The price of coal remained relatively constant from 1950 to 1969 (See Figures 1 and 2). Steam coal prices tripled and metallurgical coal prices doubled from 1969 to 1974. This price structure has created a new economic environment for coal preparation. Contributing factors to these price trends include: ? Coal Mine Health and Safety Act of 1969 ? Mid-East oil embargo of 1973 ? United Mine Workers of America contract agreements ? Productivity decrease (tons per man-day basis) ? Environmental Protection Agency regulations The increased value of coal justifies additional capital investment in cleaning facilities to optimize yield. Current trends include recovery of existing slurry ponds and recleaning of refuse. Coal preparation plant product yield and quality must be evaluated in terms of the amount of capital expended and cost of operation. Therefore, it is advantageous to optimize the plant product based on clean coal selling price and rate of return on investment.

Jan 1, 1976

By J. R. Linney

A HISTORY of the ore-mining and iron-smelting industry of the Adirondacks comprises a century and a half of pioneering by rugged individualists, both men and women. By geographical location, the climate is most severe-long, cold winters with heavy snowfall, and short seasons of vegetation growth; this, together with its remote location from large centers of population, adds considerably to the difficulties of conducting mining operations in this area.

Jan 1, 1943

By Robert M. von Storch

Chairman Doc, distinguished guests, and fellow members of the Rocky Mountain Coal Mining Institute: It's a genuine pleasure to meet with you again at the 54th regular meeting. I might add that it is always pleasant to be at the top of the batting order. The field is wide open since there is no danger of repeating something already said. At the same time, I am aware that the lead-off speaker has a responsibility to avoid stepping on the toes of subsequent speakers. I promise to confine my remarks to areas other than those to be covered by the well qualified speakers that follow. During our meetings at this convention, many fine papers will be presented. Our thanks are due Bob Williams and his hard working program committee for the superior selling that brought so many eminent speakers to our meeting. And, of course, our special thanks go to Doc Schloss, general chairman of this meeting. Doc and his able colleague, Stan Shubart, have been the spark plugs that fired up all of the arrangements we are enjoying here in Glenwood Springs. I'm sure all of us are appreciative of the many hours Doc has devoted to seeing that our meetings will be pleasant and profitable. When we mention arrangements, we always think of that master arranger, Fred Whiteside, who, as a charter member and secretary-treasurer of the Rocky Mountain Coal Mining Institute, has had more to do with more matters around these parts than just about anyone I can think of.

Jan 1, 1958

By Edmund S. Leaver

[In previous reports5/ of ore-testing studies standard methods of conducting; test with precious-metal ores selected as representative of certain mining districts were discussed in considerable detail. In addition to standard tent procedures such as direct cyanidation, amalgamation, gravity concentration, and flotation, or a combination of these methods, it is sometimes necessary to apply other methods, such as preliminary roasting and washing of the calcine with plain or acidulated water before cyanidation. In all of this work standard tenting procedure has been supplements by he necessary assaying and analyses of original ore and test products.]

Jan 1, 1941

By Abegail Endraca, Allan Sebastian, Andrew Raine, Allan Patdu

The project involves the construction of a new aqueduct tunnel by an Earth Pressure Balance TBM tunnel for the Novaliches-Balara Aqueduct No 4 (NBAQ4) project in Metro Manila. It comprises a 7.3 km long and 3.1 m internal diameter tunnel that can deliver up to 1,000 MLD of raw water and the tunnel passes under urban residential and urban populated areas adjacent to and along Commonwealth Avenue. A new reservoir intake structure was constructed in the La Mesa reservoir by a cofferdam and the TBM breakthrough connected the reservoir to the outlet surge shaft structure and the downstream pipe network system connecting to the Balara Water Treatment Plant. The TBM incorporated a double articulated head configuration to allow tight 80 m radius curves to navigate some of the difficult alignment considerations. The alignment passed very close to some existing foundations for MRT7 and needed to clear several tight curves to remain within government land ownership. The project excavated through the local Guadalupe weak rock formations and there was minimal ground movements observed as a result of the work.

Jun 13, 2023

By W. P. Campbell

Foreword At the outset, it should be stated that this paper does not pretend to present a panacea for the ills that 'frozen' wells are heir to, but rather is an attempt to bring to the attention of those whose special concern it is, a little theory and some facts, which have been brought to light recently, in connection with the problem of 'freezing' as it applies to naphtha-producing wells in the Turner Valley field, and to draw some conclusions that follow from the facts discovered. It should also be stated that the investigation is not to be regarded as in any sense complete, but in progress. Doubtless new facts will be brought to light from time to time which may modify present ideas on the subject, but whether favourable or contrary, these will be welcomed, as the purpose of the Department is to secure as complete information as possible of the factors contributing to 'freezing', since this must be the first step to an intelligent attempt to remedy or prevent its occurrence, if such can be done. It is possible, too, that the cause or causes of freezing may not be the same in all cases, but whether this be so or not will have to be determined later as new information comes to hand. Introduction One of the worries which must constantly confront the operators of gas-naphtha producing wells in Turner Valley-although all, fortunately, have not met with it-is the possibility of the occurrence of what is commonly called 'freezing' (going off production).

Jan 1, 1930

By G. M. Brownell

Introduction Within the past year a new deposit of gypsum has been opened up and brought into production in the Province of Manitoba. Until 1930, Manitoba's entire production came from Gypsumville, northwest of Winnipeg, at mile 161 on the Gypsumville branch of the Canadian National railway. However, during 1930 a gypsum bed was opened up at a point one mile south of the village of Amaranth, forty miles north of Portage la Paririe, on the west side of lake Manitoba (See Figure 1). Although no exposure has yet been discovered, the presence of gypsum below the surface in that district has been known for many years as the result of drilling for water. In 1929, J. R. Spear (1), of Winnipeg, interested some local capital in the possibility of .finding commercial deposits of gypsum, and, after some exploration work in the area with a well drill, the Amaranth deposit was located. Sixteen holes were put down at intervals of 400 or 500 feet, all of which encountered what appeared to be a continuous bed of gypsum, about thirty-eight feet thick, at a depth of 92 feet. The extent of the deposit has not yet been determined.

Jan 1, 1931

By D. Scott Barr

The Zarafshan/Newmont Joint Venture operates the Muruntau heap leach project, located in the Kyzylkum desert of central Uzbekistan. The mine produces more than 12.4 t/a (400,000 oz/year) of gold from low-grade oxide ore stockpiles adjacent to the Muruntau open pit. It is op¬erated by the Navoi Mining and Metallurgical Combine and is one of the largest gold resources known (Fig. 1). Since commissioning in 1995, total heap leach production has exceeded 21 t (675,000 oz). The joint venture uses four-stage crushing and screening to produce a final product for heap leaching, Merrill-Crowe processing and local refining.

Jan 1, 1998

By Bruce F. Grant

This report discusses research being done by the Petroleum and Natural Gas Branch und the Applied Physics Branch of the Bureau of Mines to deter-mine the most effective uses of explosives in shooting oil and gas wells, as measured in terms of rates of production from the wells. An experimental investigation of the effects of detonating explosives in shallow holes drilled in rocks, chosen to be similar to those forming oil and gas reservoirs, forms the basis of this study. Records obtained from strain gages placed in the rock around the experimental shots permit determination of the generation and propagation characteristics of the strain wave. Water-injection tests made on the test holes before and after shooting allow the increase in fluid conductivity resulting from the shot to be determined. By rotating these data to the physical properties of the rock, and by conducting shooting experiments over the range of rock types common to oil and gas reservoirs, it is expected that relationships between the fluid conductivity and the properties of the explosive and rock can be developed and used for designing efficient shots for oil and gas wells. Four series of experiment.al tests were completed during the summer of 1949 and are described herein. The results of these tests confirmed the feasibility of the experimental approach and permitted outlining the plans for future research discussed in this report. This report is presented to acquaint industry with this research program and the progress to date, so that the Bureau may have the benefit of suggestions from interested readers.

Jan 1, 1950

By E. L. Bruce

THE district of. Patricia, in the province of Ontario, lies northwest of the Albany River and extends northward to Hudson's Bay. Formerly this was the unorganized district of Keewatin, the southern part of which was divided in 1912 between the provinces of Manitoba and Ontario. The interprovincial boundary now runs north from Lake of the Woods for 275 mi. and thence northeast 375 mi. to Hudson's Bay. This district is comparable in size to all the older part of Ontario south of the Canadian Pacific Railway east of Lake Huron-thus it is roughly one-third of the whole of the present provincial area. The central part of this great triangle is one of the least accessible parts of Canada. From it streams flow southward to the English River, southeastward to the Albany, northward to Hudson's Bay and the Hayes River, and westward to Lake Winnipeg. None of the streams is large and canoe travel is not easy. The only industry it has ever had is the trade in furs. Until the development of the airplane on a commercial basis, the only means of travel was by canoe or dog-train. There is not a mile of railway in the whole district. The two areas to be dealt with lie in the southwestern part of Patricia. Red Lake is 50 mi. east of the Manitoba boundary and 75 mi. north of the transcontinental railway from Cochrane to Winnipeg. Woman Lake is 50 mi. farther east and slightly farther north. The late Dr. D. B. Dowling, of the Geological Survey of Canada, visited Red Lake and spent some time there during his exploration survey from Lac Seul to Berens River in 1893. He also visited the Woman Lake basin during the same journey, but his examination of it was much less detailed, the great area covered by him during the one field season making it impossible to make more than a hurried reconnaissance. Some prospecting in the Red Lake district followed Dowling's exploration, but the distance from railway was too great for any systematic work to be done.

Jan 1, 1928

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes? are considered one of the most promising alternatives to well-established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic-containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment-technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (000). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes are considered one of the most promising alternatives to well- established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic- containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (DoD). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By C. H. Bertoni

"The Superior Province of the Canadian Shield is the largest gold producing area within Archean greenstone rocks in the world, with total production of over 140 million ounces of gold. One hundred and fifty-five mines have individually produced more than 8,000 ounces, although only a relatively limited number of deposits (33) produced more than one million ounces of gold. The output from these 33 deposits accounts, however, for 85% of total gold production. The majority of grades (68%) ranges between 0.10 and 0.30 ounce per ton, and there is no linear relationship between grade and tonnage.Development of new gold mines reflects the history of gold prices. However, the response to the latest increase in gold prices was not as marked. It is concluded that gold deposits are becoming increasingly more difficult to find and new exploration techniques are urgently required.IntroductionWith most of its production coming out of the Superior Province, the Canadian Shield is the largest producer of gold from Archean greenstone rock s in the world. In total gold production, the Superior Province is surpassed only by the paleo-placers of Witwatersrand and the placers of the USSR (Anhaeusser, 1976). There has been no attempt so far to compile the historical production of the Province as a whole in a single document. The aim of this work is to fill this gap, not only for the convenience of having a complete list of gold producers, but, more importantly, as a basis on which to study the tonnage and grade characteristics of these deposits."

Jan 1, 1983

By John L. Miller

The synthetic fluormicas may be divided on the basis of silicon content into tetrasilicic, trisilicic, and disilicic. Properties of lead and barium disilicic fluormicas were determined to characterize these two representative members of the disilicic group. Properties described include unit-cell parameters from X-ray diffraction, optical data, chemical composition, density, melting point, and mechanical and dielectric properties. Both the lead and the barium micas were typically monoclinic; neither was sufficiently cleavable to yield usable mica splittings. Both yielded polycrystalline, machinable ceramics with excellent mechanical and dielectric properties.

Jan 1, 1963

By Malcolm Flavel

Dado que la trituración constituye el componente de alto costo en la mayoría de procesos mineros, se utiliza una tecnología basada en el resultado de los programas de investigación desarrollados por Allis-Chalmers Corporation. donde se busca reducir paulatinamente dichos costos. En ese sentido, el presente texto señala cómo reducir el consumo de energía requerida por el proceso de trituración y así minimizar la inversión de capital necesaria para construir las instalaciones del procesamiento.

Mar 1, 1983