Search Documents

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Marshall County, and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, were estimated at 3,158 million short tons as of January I, 1954. Of this total, 3,071 million short tons is in beds 28 inches and more thick. Areas in each bed except the Pittsburgh were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

E. E. Russell Tratman, New York City (communication to the Secretary): Mr. Glenn's paper brings up again the question of the part played by coal-dust in colliery-explosions. In the discussion of Sir Frederick Abel's paper on " Accidents in Mines," read before the Institution of Civil Engineers,? much was said about the dangerous properties of coal-dust, and several instances were given of the successful use of a spray of water, water and compressed air, or exhaust-steam from an engine, to keep the mine SUEciently damp to prevent the formation of dust clouds. Methods of preventing shots from blowing out; of using water cartridges to prevent flame ; and of using lime cartridges, wedges and other means of breaking down the coal were also discussed. Mr. Emerson Bainbridge referred to the explosive termed " roburite " (ammonium nitrate and

Jan 1, 1895

By Eugene W. Bartel

This report describes in detail the circuitry used in the Automated Time Domain Reflectometry System and the testing and modification done to the system to improve the units performance and consistency. The analog ATDR software is described and explained in detail. Also attempts to implement the same Assembly Language program in a higher level language (PLM) are documented along `h two versions of the PLM program - one which uses a data filtering approach to limit noise and another which uses data averaging to reduce noise. The field testing of the analog and digital ATDR units is described along with the hardware modifications that resulted. The analog unit has been abandoned and the digital unit adopted for most field tests. Tests indicate that the digital units are much more consistent and less confusing for the lay-person to operate. The results indicate that the it can locate an abnormality in a test cable to within 5% of the true location (provided the cable phase velocity is known). The units can consistently locate shunt type faults which are less than 300 ohms and series type faults which are greater than 30 ohms.

Jan 1, 1980

By A. B. Pederson, G. E. Bartlett

As a part of our study of how coal mine dusts injure the lung we have studied the effects of dusts and dust-exposed pulmonary alveolar macrophages (PAMs) on the growth of lung fibroblasts (LF). Fibroblasts were cultured near confluence in low-serum medium, either alone or in the presence of dusts, dusts plus PAMs, dust leachates or superriatants of dust-exposed PAM cultures. We report here provisional conclusions, based on initial observations. Rat LF were relatively unresponsive to direct effects of dusts, showing weak stimulation in only a few cultures, and there was no evidence that dust-exposed rat PAMs had released any growth-regulatory products. In contrast, guinea pig cells were more responsive to the dusts. The pattern of responses was quite complex. Three of the dusts stimulated LF directly (with no mediation by PAMs). Two dusts were essentially inert when added directly to fibroblast cultures, either with or without PAMs, but their leachates were active: 867 leachate was inhibitory and RF leachate was stimulatory. Dust 1361, either directly in the cultures or as an aqueous leachate, was stimulatory, and it activated cocultured PAMs to stimulate LF growth; however, supernatant products of 1361-stimulated PAMs were inhibitory. Direct exposure to 1192 stimulated LF, but its leachate was inert; cocultured PAMs exposed to 1192 had weak stimulatory effects, but supernatants of 1192-exposed PAMs were mildly inhibitory. MP3-3 had effects similar to 1192, except that the cocultured, dust-exposed PAMs had no effect on growth. We conclude 1) that guinea pig lung cells are more responsive to dusts than are rat lung cells, 2) that dusts can influence growth of LF by four kinds of interaction (by direct dust-cell interaction, by release of soluble dust components into the culture medium, by activating P AMs to exert direct cell-cell interactions, and by activating P AMs to release growth regulatory products into the culture medium), 3) that each kind of interaction may be neutral, inhibitory or stimulatory, depending on the dust tested, 4) that four of the dusts tested were neutral, inhibitory or stimulatory, depending on the assay (the fifth <lust was either neutral or stimulatory), and 5) that the effects of soluble mediators (leachates or products of activated PAMs) frequently did not correspond with the direct dust-cell or PAM-fibroblast effects. These results suggest that the nature of the dust-lung interaction at the level of cells and molecules is exceedingly complex. These observations need to be confirmed and extended to determine what characteristics of the dusts determine the nature of the cellular responses, and to determine which patterns of responses are detrimental and which are beneficial in the overall health of the dust-exposed lung.

Mar 1, 1989

By Phil Rice, Mohammed Nasim, Richard Flanagan

"The Gateway Trans-Hudson Partnership (GTHP), a joint venture of WSP USA, Inc., AECOM USA, Inc, and STV Incorporated, is providing preliminary engineering services to Amtrak for the Hudson Tunnel project as well as supporting the NEPA process for getting the record of decision (ROD). This preliminary engineering design effort by GTHP includes geotechnical exploration and laboratory testing, design of structures, tunnel contract packaging and procurement planning.The Hudson Tunnel Project includes the construction of a new Hudson River Tunnel system and rehabilitation of the existing North River Tunnel. The new tunnel system will be constructed south of the existing North River Tunnel, from North Bergen under the Palisades to Hoboken in New Jersey, below the Hudson River, and connecting directly to Penn Station in New York (Fig. 1). The tunnel system is configured as two single-track tubes, intermediate ventilation shafts and cross passages in compliance with NFPA- 130 requirements. The adjacent surface alignment west of the Palisades will be constructed on viaducts, embankment and retained fills. The existing North River Tunnel (Fig. 2) consists of two single-track, electrified rail tunnels extending from tunnel portals in North Bergen, New Jersey to Penn Station in New York. Completed in 1910 by the Pennsylvania Railroad, the tunnel opened at the same time as Penn Station and the four, single-track, East River tunnels that connect Penn Station to Queens and onto Long Island and New England, respectively. Both tunnels in the existing North River Tunnel were inundated with brackish river water during Superstorm Sandy (Fig. 3), resulting in the cancellation of all Amtrak and NJ Transit service into New York City for five days. After the brackish water was removed from the tunnels, the residual chlorides and sulfates have had on-going detrimental impacts on the interior concrete and rail systems."

Sep 1, 2019

By E. Don Dilling, Wm. F. Hergert, J. W. Pennington, C. E. Wood, M. J. Slendlove, H. A. Doerner

"INTRODUCTION The Bureau of Mines began a study of various methods for producing magnesium metal from magnesite ores in 1936 at Pullman, Wash., with the cooperation of Washington State College. This work included a study of the basic principles involved in the reduction of magnesium oxide by carbon, which soon led to the development of a continuous process. In May 1939, a small pilot plant was operated, which included a small single-phase arc furnace with a hydraulic feed mechanism and an oil-spray device for shock cooling the metal vapor. 5/Subsequently, the Ford Motor. Co., Dearborn, Michigan, began a study of this process on a larger scale. A pilot plant with a nominal capacity of 10 pounds of magnesium metal per hour was constructed and operated intermittently. A larger unit with a nominal capacity of 100 pounds of magnesium per hour was partly constructed when war activities prevented experimental work.In the meantime, the process was greatly improved through continued investigation by the Bureau of Mines at Pullman, and these improvements were successfully tested by continuous operation in a small pilot plant having a normal capacity of 4 pounds an hour."

Aug 1, 1945

By S. M. Marshall

The investigations recorded in this bulletin were conducted by the Pacific Coke & Coal Co. in cooperation with the United States Bureau of Mines and the University of Washington. They cover one phase of a comprehensive investigation to determine whether coals from an extensive, undeveloped area of Pierce County, Wash., can be used in the manufacture of coke for the iron blast furnace. The completed investigation had three parts: (1) A geological survey of the coal property, (2) washing and crushing tests of the coals, and (3) coking and by-product tests. The geological survey, which was not conducted in cooperation with the Bureau of Mines and the University of Washington, included systematic tracing of the coal beds by test holes throughout the property, except some portions covered by an impenetrable layer of glacial drift. By this means all of the beds were correlated, their thickness and general character were determined, and tonnage estimates were made. Only such parts of the survey results as are necessary to a full explanation of the investigations described herein are included in this bulletin.

Jan 1, 1931

By Emily Wortman-Wunder

While the mood at the 2013 annual joint meeting between the Pittsburgh Coal Mining Institute of America (127th Annual Meeting) and SME Pittsburgh Section (68th Annual Off-the-Record Meeting) in Canonsburg, PA was subdued following a rocky year in the coal industry, attendance was down only slightly, to 300, and overall, the meeting?s focus was optimistic about the future of coal. The conference began by addressing one of the central challenges of coal mining head-on with a keynote address on the status of safety in the mining industry. Noting that two more U.S. miners had died in 2013 than by the same date in 2012, the National Mining Association?s (NMA) Senior Vice President of Regulatory Affairs Bruce Watzman made a plea for a new approach to safety. He described the NMA CORESafety initiative, a program that promotes proactive safety measures versus a compliance-driven model. CORESafety, described in more detail on pp. 29 of this issue, focuses on developing successful ways to change company cultures of safety and behavior. Other industries that have adopted this approach have seen dramatic drops in fatalities, including the Australian mining industry, which has seen its annual fatality rate drop to nearly zero even while the number of people employed in the industry has soared. The rest of the morning?s sessions explored what is arguably the industry?s biggest challenge right now ? maintaining the social license to operate.

Jan 1, 2014

By Alex C. Smith, Michael J. Sapko

A series of explosive detonation experiments was conducted in NIOSH’s Bruceton and Lake Lynn Experimental Mines to evaluate low level (<6 psig) detonation wave propagation behavior in single and multiple entry configurations. Entry cross-sectional area varied from 5 to140 m2 and explosive weights of Pentolite ranged from 0.24 to 2.4 kg. Behavior of the detonation wave was evaluated through recording of the pressure as a function of time and distance from the explosive detonation in single and multiple entry interconnecting tunnels. Peak pressure from detonation of an explosive in an underground mine maintains magnitude for a greater distance than is the case on the surface and is shown to follow the simple scaling rela-tionship P = 702.8(W/Vt)0.514(0.65)n, where P is the peak detonation pressure in kPa, W is the weight of the explosive charge in kg, Vt is the total volume in m3, and n is the number of splits, n = 0, 1, 2, …n. The total energy, or impulse, I, generated by these detonations can be expressed as I = 1.34(W/A)0.64n, where W is the weight of the explosive charge in kg, A is the area of the main tunnel in m2, and n is the number of side en-tries, n = 0, 1, 2, …n.

By D. R. Torgoson, Th. G. Sahama

"This paper contains some new thermodynamic data for silicates in the series Mg2SiO4-Fe2siO4 and MgSiO3-FeSiO3 and gives the results of a thermodynamic attack on the problems of stability end parageneses.. Although some data are lacking satisfactory agreement with mineralogical and petrological observations is indicated.The use of thermodynamic methods in mineralogy and petrology has been rather limited, because accurate thermal data, especially for the more complicated and more important rock-forming minerals, have been too scanty to permit any systematic application to problems in those fields. It is, nevertheless, a fascinating task to investigate to what extent the mode of occurrence and the stability relations of the minerals and mineral parageneses, as revealed by petrological and mineralogical observations, agree with predictions of thermodynamics. At the present stage of development calorimetric data are needed for most of the abundant silicate minerals.Measurement of the heats of solution in hydrofluoric acid of minerals in the series Mg2SiO4-Fe2SiO4 and MgSiO3-FeSiO3 affords a ready means of obtaining their heats of formation from the oxides. Combination of such data with entropy and heat-capacity values gives a means of obtaining free energies of formation from the oxides, which, in turn, are connected di¬rectly with stability and paragenoses.The two silicates of magnesium, Mg2SiO4 and MgSi03, occur as rock-forming constituents as forsterite and clinoenstatite or enstatite. The orthosilicate (forsterite) forms a series of isomorphic mixtures with ferrous-orthosilicate (fayalite). The continuity of this series, suggested by petrological observations, has boon proved experimentally by Bowon and Shairer.4/ The present work shows that those minerals constitute a series of perfect solid solutions - that is, a series of solid solutions for which heats of formation from the individual pure silicates, Mg2Si04 and Fe2SiO4, aro negligibly small.The metasilicates of magnesium and iron also form an isomorphic series. However, this series differs from the forstorito-fayalite series in the fact that the most iron-rich mixtures, between about En10Fs90 and pure Fs, appear to be unstable with respect to the paragenesis iron-rich olivine plus quartz. The supposed instability of pure FeSiO3 as a crystalline compound, at least at high and at moderate temperatures, is remarkable, as no crystal struc¬tural reason for such instability is apparent. The present work indicates, also, that these minerals form a perfect series of solid solutions and throws additional light on the instability question.In the following, the samples used in this investigation will be described. For each of the natural olivines and orthopyroxenes, with the exception of sample L, a chemical analysis was made of the purified and actually used fraction. All the analytical work was carried cut by Oleg v. Knorring, and the specific gravity determinations, by moans of a pycnomctcr, by Oiva Joensuu, both of the University of Helsinki, Finland. The determinations of the optical properties were made by Mrs. Toini Mikkola, of the Geological Survey of Finland."

Feb 1, 1949

By R. R. Tatiya

"The ultimate aim of a mine design is to determine the development work involved and resources required by adopting one or more specific alternatives. A part of the process is the production of mining plans/designs, an outline of the amount of work and costs involved as well as a prediction of the revenues expected. The paper aims to examine these aspects of mine design using the computer models developed. These models are capable of designing and performing economic analysis for one or more stopes for a continuous orebody. IntroductionTatiya and Allen (1987) have described ’defining stope boundaries using a computer.’ Using the stope boundaries defined or even hypothetical ones, algorithms have been prepared to design the layouts of the following stoping methods: 1. sublevel stoping (longitudinal as well as transverse);2. DTH (Down-the-hole) stoping; and3. flat back cut and fill stoping with posts and pillars.Tatiya (1989) presented this work at the 21st symposium on the application of computers and operations research in the mineral industry (APCOM). Economic analysis of a stope is the additional feature incorporated with these algorithms.The system has been tested by an economic analysis of the three stoping methods modeled for a small portion of a deposit of a copper mining complex. The deposits at this mining complex form lenses of varying shapes and sizes, having low copper content. These chalcopyrite lenses are steeply inclined with a thickness in the range of 5 m to 60 m. The strata are competent and suitable for underground mining.In different sections of the mines different sets of equipment are used to perform the basic unit operations. Some of the ore handling levels in the mines are trackless, the rest are tracked."

Jan 1, 1998

By SAM YOUR

PROCESSING, technology and application of non- ferrous metals-copper, lead, zinc, aluminum, nickel, precious metals, foundry metallurgy, less common metals, secondary metals-are the special field of the Institute of Metals Division. New developments in this field during 1930 are more or less briefly out- lined in this review prepared by the papers and publications committee of the Institute of Metals Division as follows:

Jan 1, 1931

By Edward Hall Smith

The E1 Indio Mine is located in the Andes mountains about 180 kilometers East of La Serena, capital of the Fourth Region of Chile. It is reached by an international highway running up the Elqui Valley as far as Juntas from where the last 42 kilometers is on a road constructed by the Company. The plant is located at 3.900 meters above sea level among extremely rugged terrain with nearby mountains rising about 5.500 meters. Climatic conditions at these altitudes are severe with winter temperatures down to -20°C. Snow storms lasting several days and leaving up to two meters of snow have been experienced, while fierce winds are corm=.

Jan 1, 1984

This publication summarizes, for potential contractors and all other interested parties, the research and development of in-house and contract projects programmed by the Bureau of Mines for fiscal year 1983 (October 1, 1982-September 30, 1983) under its Health and Safety Technology program. The objective of these projects is to provide an ordered and sequenced series of advance toward the Bureau&apos;s overall goal of providing the systems technology required to create a more healthful and safer working environment for the Nation&apos;s mining and minerals processing workers.

Jan 1, 1982

By CHARLES R. KETES

I. INTRODUCTORY. INDUSTRIALLY, the most important service that geological science can now render to mining in the Upper Mississippi leadand zinc-fields is to devise some practical scheme whereby the productive ore-belts may be located with greater certainty than they have been in the past. Up to the present time there has been little service of this kind, and in spite of all that has been worked out concerning the geologic features of the region, and notwithstanding all that has been written about these ore-deposits, this particular phase of the subject has been, for some reason or other, the very one that has received the least consideration. The neglect by geologists in this respect has been all but complete. The following notes are suggestive of some practical solutions to the problems presented. As here suggested, the geologic relationships of the ore-bodies were surmised some years ago, though somewhat vaguely perhaps. No opportunity for securing critical data appeared until recent investigations of a private character were undertaken, which bad in view the extensive prospecting of undeveloped areas. Fresh from rather wide experiences of a decade in the principal mining-regions of four continents, and after a lenstrum&apos;s residence among the chief mining-camps of the West and of Mexico, under conditions which measured geologic hypotheses in meters and rigidly tested their values in, terms of dollars, the recent return to the Joplin field and a new survey of its ore-conditions were fraught with somewhat unexpected results. Aspects of the ore-deposition were presented of which previously there was no hint. Ten years&apos; absence from the district had tended greatly to clarify former hazy impressions. It enabled many features, then only dimly outlined, to be considered more nearly in their true perspective and in their real relationships to their surroundings. It permitted a great mass of details collected a dozen years before in connection with the work of the Missouri Geological Survey to be viewed under new light and to

Feb 1, 1909

By John H. Soule

The Torpedo Copper mine in the Organ Mining District, Dona Ana County, N. Mex., was discovered In 1899. Production was begun immediately and continued until 1907. Since 1907 very little ore has been produced, although Many individuals and companies have been interested in the property at one time or another. Approximately 6,621 feet of diamond-core had been completed on the property before 1949. The results from some of this drilling were unsatisfactory because of the poor core recovery. In addition to its investigation of the Torpedo ore deposits, attention was given by the Bureau of Mines to obtaining better core recovery through the use of special equipment and techniques. This project was begun October 3, 1949, and was completed April 30, 1950. Four diamond-drill holes totaling 2,140.5 feet, which includes 18.2 feet of overlap in a deflected hole, were drilled. All drilling was done with a Government-owned hydraulic-feed drill with some special rods and core barrels, in addition to the usual equipment. The over-all core recovery was 89.5 percent. Omitting the drilling in overburden where little or no core was desired, the recovery was 94.6 percent. Core recovery in the ore zones averaged 95.2 percent. This paper describes the location, the general features of the area, the geology, the Bureau of Mines procedures, and the results attained by these procedures.

Jan 1, 1952

By Gordon MacVean

THE adoption of rock dusting, as a safety measure, has made notable progress in the West Virginia coal mines since May, 1925. At that time there were but two mines in the State that were thoroughly rock dusted, mines No. 2 and No. 12 of the Boone County Coal Corp., at Sharpless. Since then it is probable that 75 per cent of the coal operators in the State have given consideration at one time or another to rock dusting. This growth of interest followed the meetings of the various mining institutes all over the country, during the summer of 1925, at which papers were presented, drawing the attention of the coal mining operators to the merits of this safety measure. Yet outside of the experience with rock dusting at the Old Ben Coal Corp., of Southern Illinois, and the Carbon Fuel Co., of Rains, Utah, there had been no actual occurrence in the coal mines of the United States, which could be taken as positive evidence of the efficacy of rock dusting in the prevention of the propagation of coal dust explosions. The U. S. Bureau of Mines, however, had run innumerable tests under conditions which closely approximated actual coal mining conditions and had clearly shown that rock dusting was effective.

Jan 1, 1926

By W. W. Adams

Increased employment and a lower accident-frequency rate were the outstanding features of the metal- and nonmetal-mining4 industries of the United States in 1939 compared with 1933, according to reports furnished by individual mining companies to the Bureau of Vines, United States Department of the Interior. Except for 1937, the reports for 1939 showed gains both in number of employees and number of mar -hours worked over all years since 1929. The accident-frequency rate per million man-hours of exposure to mining hazards was lower than in any year since 1925. Reports for 1939 revealed a total of 111,909 men employed in and about mines, an increase of inure than 8 percent over 1931 The total volume of labor performed at all mires was slightly more than 299 million plan-hours, an increase of mare than 10 percent over 1938. As these gains suggest, the average employee had a longer period of work in 1939, the increase amounting to r workdays per employee.

Jan 1, 1941

By H. V. Kinsey

"IntroductionTITANIUM is probably the most widely publicized metal today. Much has been written, both in the lay press and the technical press, about its properties and potentialities. In view of the fact that Canada possesses large quantities of titanium-bearing ore, and could conceivably become a major producer of metallic titanium, it was felt that a paper dealing mainly with the physical metallurgy of titanium would be of interest to this Institute. This paper is concerned chiefly with the useful properties of titanium and its alloys and the fundamentals governing the modification of its properties by alloying.Physical Properties of TitaniumTitanium belongs to a family of metals that have been termed 'gas sensitive' (I), because their mechanical properties are altered by certain gases which they readily absorb and retain. Other metals of this group are zirconium, hafnium, vanadium, columbium, tantalum, and chromium. Titanium has a strong affinity for oxygen and nitrogen and once it has absorbed these gases they cannot be removed either by melting in vacuum or by any degassing agent. These gases, when present in excess of about half a per cent oxygen plus nitrogen, render the metal brittle and useless as a structural material.Some of the typical physical properties of titanium are listed in Table I along with those of common structural metals for comparison."

Jan 1, 1953

By U. K. Custred

Who We Are Farmland Hydro (FHLP) is a Limited Partnership formed by Farmland Industries, the largest U.S. farmers’ cooperative, located in Kansas City, MO, and Norsk Hydro, a large Norwegian company engaged in fertilizer, petroleum and the specialty metals industry. Both of our parent companies have a long history of commitment to the fertilizer industry. This year, Farmland Industry celebrates its 71st year in the business, and Norsk Hydro celebrates its 100th operating year! We employ approximately 300 associates in Central Florida. What We Do Farmland has been active in Hardee County, FL since the 1970’s as a large landowner and citrus grower. We plan to expand this activity into phosphate rock mining. The phosphate rock produced here will be shipped to our nearby chemical fertilizer complex in Polk County, where we produce quality phosphate products - liquid and granular fertilizers. Of the phosphate rock mined, 90% is used to make fertilizer. Other uses include animal feed, vitamins, medicine, light bulbs, soft drinks, film, flame resistant fabric, optical glass, toothpaste, bone china and other consumer products.

Jan 1, 2000