Search Documents

By E. P. Carman

This report is the 20th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations; it is the second4/ to be issued on a calendar-year basis. Previous reports related largely to publications by Bureau authors during the reporting period. This one discusses the publications issued during 1955 and in addition describes briefly the work in progress during the year. Further details on the published work may be found by referring to the publications cited in the footnotes. The Bureau continues to direct its research and technologic work on coal toward safer and more efficient mining, improved preparation, and more effective utilization, with the ultimate twin goals of promoting conservation and insuring that coal will make its maximum contribution to the Nation's industrial capacity. Significant advances toward these goals were made in 1955.

Jan 1, 1957

By Timothy Barton

The uniaxial compressive strength (UCS) is the most fundamental measurement used in geotechnical rock characterization for mine design. While there are standardized procedures for how to conduct UCS tests, there are no firm guidelines as to when to conduct them. However, it is well known that the strengths of at least some rocks can change during the time between when the core first comes up out of the hole and when it is prepared and tested in the lab. The goal of this NIOSH (National Institute for Occupational Safety and Health) study was to evaluate UCS changes occurring in a broad range of weak coal measure rocks over a one-year time span. The study found the highest moisture contents were measured when the core was fresh, immediately after it was taken from the hole. The specimens then dried rapidly over the next few weeks. Subsequently, sample moisture contents decreased slightly in the winter and increased in the summer in response to the ambient changes in humidity. The measured UCS of the core also changed during the year, apparently in response to changes in the moisture content. The UCS values from the dry, winter months were, on average, 60% higher than the values obtained when the core was fresh, and the summer UCS was approximately 11% lower than the winter UCS. These findings have implications for the use of UCS as an input parameter for both empirical and numerical mine design methods. UCS values of unprotected core tested weeks to months after drilling can be significantly stronger and indicate stronger roof sequences than warranted. In order to obtain the most representative and reliable UCS value, it is necessary to test the core, or wrap and seal it, at the drill site shortly after recovery.

Jan 1, 2008

By Richard Paul Seelig

THE following review covers published information on pressing of metal powders at room temperature. Only those operations are considered which occur between the time the powder is filled into the cavity and the compact is ejected from the die. Thus, this review does not concern hot pressing, coining or sizing feed or flow problems, commercial presses nor designs. It was also necessary to disregard to a large extent the effect of pressing on subsequent operations and on properties after sintering. The pressing operation is considered independently in its function to compact loose metal powder into useful shapes which can subsequently be handled. There are some comments by the writer in connection with a few of the findings quoted in the literature in order to stimulate thought and discussion. The selection of references quoted in the text is in some cases arbitrary although an attempt was made to favor papers containing novel ideas, techniques or results which may stimulate future research. In order to enable the reader to check further into the subjects mentioned, the original, rather extensive, bibliography is appended even though not all the references are touched on in the printed version of this review. EXPERIMENTAL APPROACH The equipment used by various workers, for example a die design created by Bridgman,22 is very interesting. The die insert has a conical external surface. The vertical pressure exerted on the punch transmits itself to the die which in turn is pushed harder into its tapered retainer. Thus, the higher the pressure exerted on the punch, the higher also the pressure exerted inwards on the die inserts. In as much as this pressure counteracts the internal pressure from the compact the two stresses balance each other so that it is possible to obtain tremendous pressures without breaking the die. The die collar was made from an oil hardening tool steel, heat treated to a tensile strength of some 300,000 psi. The die was closed at the bottom by a plug made from special tool steels. Bridgman found that there is no steel which will withstand a compressive stress of 700,000 psi without continuous slow flow or immediate fracture. Therefore, the only material suitable for use in the pressing punch was sintered carbide. In view of the ingenious design it was possible to use special tool steel as die material. Jones22 raises the question whether this method of pressing has practical application in powder metallurgy. Al- though these tremendous pressures cannot readily be utilized without many special precautions, the tapered die and retainer idea is believed to be useful even for lower pressures. Bridgman, himself,8 calls attention to the fact that the properties

Jan 1, 1947

By H North, J Barringer, S McNeill, D Pairman

Models of ground surface elevation, slope, aspect, curvature, roughness, deformation, as well as other features are gathered together in the term Digital Terrain Model (DTM). DTMs can be generated from a wide range of technologies such as ground surveying, aerial and satellite imagery, including both active and passive sensors. Some elevation derived parameters, such as roughness and slope, can be measured directly using innovative active sensor technology and smart processing, rather than via traditional processing of elevation information. Such models are used as part of a visual interpretation process, and increasingly for computer-assisted analysis using visualisation technology. There is an ever-increasing demand for DTM information to be used in the mineral exploration and mining industry, and consistent pressure from industry to develop models of higher spatial resolution, higher accuracy, and better overall reliability, regardless of the world-wide location of interest. This presentation will survey the range of techniques available for DTM generation, including active (LIDAR, SAR interferometry and differential interferometry) and passive (optical or SAR stereo) methods, as well as interpolation methods (contour or structure interpolation), and the economic placement of these various techniques in the local and regional context. The research issue oftrue-ground elevation models and slopes is also addressed, using LIDAR and SAR polarimetry as signpost technologies. Particular emphasis will be given to the strengths and limitations of new data sources that will, over the next few years, make the acquisition of elevation models of remote regions of the world inexpensive and relatively accurate.

Jan 1, 2000

By Donald Koch

The project investigated regional impacts of mining on the ground water system of the Powder River Basin by: 1) establishment of a regional ground water monitoring network, and 2)development of , set of digital computer models to simulate ground water flow and quality, ground water contributions to surface water flow and quality (i.e., baseflow), and watershed run-off and recharge. Over 100 wells were monitored for physical and chemical parameters. Data were used as input to the model; and for the development of a comprehensive data base. The basin was modeled on a regional and subregional scale using a finite -difference model employing an alternating difference technique. Two water-shed models were evaluated for their ability to provide runoff and recharge inputs to the basic ground water model. Application of the regional and subregional models using conservative mining scenarios showed that drawdowns may extend west from the mines as far as ten miles but that impacts would be insignificant on a regional scale. The watershed model could be effectively applied to small watersheds only.

Jan 1, 1982

By Ernst A. Hauser

IN a paper published three years ago,' the term "silicic chemistry" was used for the first time to emphasize the increasing importance of the chemistry of silicon in science and technology. The development through which the colloid chemistry of siliceous matter has gone since then is in itself ample proof that the coining of this new term for this branch of colloid science was not presumptuous. Until quite recently, however, silicic chemistry concerned itself only with the composition and colloidal properties of natural and synthetic siliceous matter, but had not paid much attention to the genesis of this matter, particularly to that of the clay minerals. What is even more disturbing, particularly from an educational point of view, is the fact that neither mineralogy, geology, nor metallurgy has fully realized the important role colloidal phenomena must have played in the genesis of our planet and the formation of minerals generally speaking. Considering the importance of colloid chemistry today in the fields just mentioned, it is not surprising that the theories most agreed upon by geologists and mineralogists for the origin of clay minerals are not acceptable from a strictly colloid chemical point of view for the genesis of these most important and most abundant components of the earth. Of all the theories pertaining to the origin of clay minerals, those still most accepted by geologists and mineralogists are the "residual clay" and the "transported clay" theories.15 The former is based primarily on the assumption that the formation of clay minerals is the result of surface weathering of fresh rocks, or is due to the action of solutions. Taking the action of water on orthoclase as an example, the most recent ideas have been summarized by H. Jenny13 as follows:

Jan 1, 1952

By Ronald B. Stotelmeyer

This report summarizes the U.S. Bureau of Mines evaluation of the mineral resources of eight roadless areas in several National Forests in Montana. The areas are amoung those that have been proposed as additions to the National Wilderness Presevation System In various sessions of the U.S. Congress. Mineral Commodities present include gold (lode and placer), silver, copper, lead, zinc, molybdenum, tungsten, rare-earth elements, fluorite, and barite. Numerous mineral deposit types occur. Past production was from gold placers and vein-type deposits. There is potential for development of large volume porphyry copper-molybdenum, disseminated gold, stratabound copper-silver, and exhalative massive-sulfide metallic deposits. A substantial increase in metal prices is needed before any known vein-type deposits will be economic.

Jan 1, 1994

THE IRON HUNTER. By Chase S. Osborn, pp. 316, Ills. 10. The MacMillan Company, New York. 1919. An autobiography, the story of a Hoosier boy who fought his way to manhood and power through early misfortune and poverty, from street urchin and newsboy, to editor and author; from lumberjack and dock walloper to statesman and Governor of Michigan. The reader has the measure of the man in the first chapter, a dramatic recital of how the fighting boy editor cleaned up a lawless mining camp of 40 years ago. The thread of the narrative is the author's life-long devotion to outdoor living, ex-ploration and travel. Residing in Sault de Sainte Marie, Mich., in the heart of the Lake Superior country, he took his delight and, incidentally, found his fortune in prospecting the north woods for iron ore; eventually, extending his travels to the continents and many of the islands of the world, he discovered what, he believes-to be a great iron range in Madagascar. In this book there is plenty of anecdote, a great deal of wholesome social and po¬litical philosophy and some interesting sidelights on the characters of some of the author's prominent contemporaries in the political life of Michigan. The style is direct and animated, flavored and illuminated with the vernacular of Hoosierdom and the woods country of the North. The author levies on the vocabulary of the sciences and the classics for many a noun and adjective and, with Rooseveltian license, now and then coins a word. The reader's interest will be gripped from cover to cover, albeit he may occasionally need a dictionary. R. C. A.

Jan 11, 1919

By Halvorsen N

For mining medium-hard materials on the surface, "Continuous Surface Miners" have been employed for some years. The latest generation surface miner extends the performance of this type of machine to the point where the same cost efficiencies can now be achieved in medium-hard materials as has been achieved in softer materials by machines such as the bucket wheel excavator. The paper explains briefly the technology of the Krupp Surface Miner (recently released to the market) and develops the costs of ownership and typical operating costs. Comparisons are made between a shoveLtruck system and Krupp Surface Miner (KSM) systems based on both truck and conveyor transport systems. Further benefits of mining with the KSM, such as environmental, selective mining and improved product reovery are discussed briefly. The equipment is now available to mine semi-hard materials (with compressive strengths up to 60MPa) on a continuous basis and reap the benefits which continuous systems can deliver. All new and existing open cut mines should review their costs with regard to this technology.

Jan 1, 1990

By Cam Thomas

The initial application for reflectorless laser technology was for profiling rock faces to determine front row burden and improve flyrock control and airblast. Over the past fifteen years a number of laser systems have been developed for general ground modeling purposes and GPS offsets, but these advances have yet to gain common acceptance in construction, mining and quarry blasting. This paper will outline a number of applications for reflectorless laser technology, including the latest method for rock face profiling, mapping, and 3-D modeling to calculate available and excavated rock volumes. Drilling deviation measurements will be presented in conjunction with rock face profiling to demonstrate how this information can be used to improve blast results. In complicated excavations, the actual quantity of rock excavated for payment purposes and the amount of overbreak can be very controversial. Procedures to calculate these volumes using laser technology will be outlined and comparisons will be made between these results and traditional techniques.

Jan 1, 2003

By P. R. Jones

The Bureau of Mines has written a computer program for the design and cost of a shell and tube type heat exchanger, in which a change in phase occurs on the shell side. The total cost, which was minimized, includes the annual fixed charges and annual operating costs. The program was written to meet the following requirements: (1) Triangular pitch, (2) single or multiple pass, and (3) heating or cooling. Price optimum design was obtained for four standard tube diameters and pitch. Standard heat exchangers whose area equaled or exceeded the required area are also listed. The program was made adaptable to various fluids and to various tube dimensions by including many of the required data such as physical properties of the fluids, tube data, and standard shell data as input data.

Jan 1, 1969

By R. W. Stahl

Employees and dollars are necessary to all enterprises and any force, such as fire, which destroys either, can bring very serious consequences, including business failure. Since everyone acknowledges the necessity of conserving human life, we will devote most of our paper to the economic factors involved. A coal-mine fire is considerably more difficult to combat than a fire in a surface building because of the combustible surroundings in the mine, the explosive gases emitted from the coal, the suspension of explosive dust when mine timbers burn and the unsupported roof falls, the limited space in which approach to the fire can be made, and the limited avenues of escape. A survey of coal-mine-fire protection indicated that a rather low value was being placed on property and equipment. This prompted comparison with other industries. The comments made in this comparison are not intended as an indictment of the coal industry, since we do have mines that are well protected against fire, but the comments on conditions at the mines visited are factual and may help others to improve similar conditions. SURVEY PROCEDURES Plants of the steel, aluminum, rubber, chemical, and petroleum industries were surveyed, and all facets of the fire-protection scheme were covered. The industrial plant invariably had four times as much water readily available for instant use than the mine. In many mines where water is available, no equipment for applying it is provided, such as hose, nozzles, and adapters, so that time is lost in collecting this equipment. (See Table I.) EXTINGUISHERS Many more and generally larger portable extinpishers are available at the plant as compared to the mine. The extinguishers are generally placed nearer to sources of danger. In addition, respiratory protective equipment is always available at strategic points in plants but only in a few mines. (See Figs. 1 and Table 11) INSPECTING AND TESTING EQUIPMENT Plant water facilities are checked weekly and flushed at 6-month intervals, and hose is pressure-tested at least yearly; some mines check water yearly, but hose is not tested unless used. Fire extinguishers are inspected weekly in plants and completely overhauled yearly; one mine had monthly checks and overhauls only after use. FIRE BRIGADES AND TRAINING Every plant had designated fire-fighters and some complete full-time brigades; at one mine a chief mechanic was designated as being in charge of fires, and other depended entirely upon officials who might not be familiar with the equipment. COST OF FIRES AND PERCENTAGE OF CAPITAL INVESTMENT IN FIRE PROTECTION The direct cost of recent mine fires ranged from $128,000 to $240,000; indirect costs, such as lost tonnage, idled equipment, lost orders, and the like might run the cost to over $500,000. (See Figs. 2 and 3).

Jan 1, 1961

By K. T. Aust

The occurrence of annealing twins in high-purity aluminum resulted in the formation of grain boundaries having orientation relationships which correspond to a high density of coincidence sites. The results provide support for the coincidence site model and indicate that large-angle coincidence boundaries have lower free energies than large-angle noncoincidence boundaries. Observations are presented concerning the coherent structure of twin interfaces in aluminum and the importance of inter-facial energy in preferred orientation. RECENT experiments1 have shown that when an annealing twin is formed during grain boundary migration in zone-refined lead, a large-angle random boundary is replaced at the growth front by a large-angle coincidence site boundary. The coincidence site orientation relationships obtained by twinning were of the type considered by Kronberg and Wilson,2 Frank,3 and Dunn.4 On the basis of the theory of annealing twins advanced by Fullman and Fisher,5 these observations indicate that the energy of a coincidence site boundary is less than the energy of a random boundary by an amount which exceeds the energy of the coherent twin boundary. This energy difference between the coincidence and random boundaries must be at least about 5 pct since the ratio of twin boundary energy to grain boundary energy in zone-refined lead is 0.05 * .014.6 Fullman7 has found that the twin boundary energy in aluminum is about 21 i 5 pct that of a large-angle grain boundary. A twin boundary energy as large as this would be expected to exclude the formation of many coincidence site grain boundaries, especially those which have a relatively low density of coin- cidence sites. Therefore, if the coincidence site model is a useful interpretation of certain large-angle boundaries, then it would be predicted that only coincidence boundaries which separate adjacent crystals with a relatively high density of coincidence sites may be obtained as a result of twinning in aluminum. The present experiments provided a means of testing this prediction since annealing twins occurred during the growth of recrystallized grains into striated, melt-grown single crystals of zone-refined aluminum. EXPERJMENTAL PROCEDURE A striated single crystal of zone-refined aluminum, about 1 cm sq and 37 cm in length, was obtained during zone melting of aluminum of 99.996 wt pct starting purity in a graphite boat under helium atmosphere.8 A molten zone of 2 to 3 cm in length, which was maintained by induction heating. was passed along the length of the bar for eleven passes at a rate of 0.9 mm per min. An additional final pass was given at a rate of 0.2 mm per min. The center portion of the zone-melted bar was characterized by an electrical resistivity ratio between room temperature and 4.2° K of 8000 to 9000. Single crystals of 1 to 2 cm in length were removed from the center section of the zone-refined bar and electrolytic ally polished in a 2:l solution of methyl alcohol and concentrated nitric acid. The specimens were then chemically polished in Alcoa R-5 solution. X-ray analysis of the single crystals indicated the presence of striations or lineage substructure having misorientations as high as 2 deg. New, recrystallized grains were introduced into each striated crystal by the technique of artificial nucleation and growth, previously described.9 During the growth of the recrystallized grains at 300' to 600°C in argon, it was sometimes found that a

Jan 1, 1962

By S. H. Lorain

This paper briefly describes the principal known commercial and near commercial deposits of gold-bearing gravel end the principal placer mining operations of Idaho County, Idaho. It is one of a series of similar papers on western mining districts. The data used in writing this paper were gathered during the summer of 1937. Information concerning gold-bearing gravels was obtained from prospectors and operators, while operators supplied most of the data on mining operations. No attempt was made actually to test the gravels. The principal object of the examination was to indicate placer areas worthy of further investigation by prospective operators.

Jan 1, 1938

Although not immune from the problems affecting the U.S. economy generally, the mineral industry in 1991 contributed nearly $300 billion in the value of processed materials of mineral origin. Supporting this contribution, the Bureau of Mines continued the research and analytical programs highlighted in this annual review. Featured in 1991 were such relatively new programs as minewide monitoring applications in ground control and advances in processing of ceramics and composites, along with more traditional research into health, safety, and mining technology, minerals and materials science, and environmental technology. Under Bureau sponsorship, a National Minerals Policy Forum brought together some 200 executives from industry and Government concerned with minerals policy to begin a dialogue on developipng a policy statement on current minerals issues. A major feature of the forum was the keynote address by Secretary of the Interior Manuel Lujan, Jr.

Jan 1, 1992

The stability of paste fill bulkheads forms an integral part of a successful paste fill system. Bulkheads are constructed at the draw points of open stopes to contain paste fill while the initial pour cures and forms a consolidated plug. Mobilization of uncured paste fill as a result of a bulkhead failure can lead to significant consequences, including endangering the safety of personnel, property damage and production losses and delays. The loading conditions in the paste fill and the resultant lateral loads on the bulkheads are complex and are dependent on many factors. This paper presents a case study of several paste fill bulkhead failures; the results of an in-situ pressure monitoring program to ascertain the pressure loads, and the subsequent paste fill bulkhead evaluation.

May 1, 2007

The complex organic chemicals in coal differ from those in petroleum mainly by the ratio of carbon atoms to hydrogen atoms; this ratio is about 2 for coal and 1 for petroleum. By changing the ratio, coal can be converted into compounds similar to those found in petroleum. In. very simplified form, omitting here the special conditions required, the paths by which this can be done are: [ ] Part or all of the coal is first gasified by reaction with steam and oxygen, either in a gasifier or while the coal is still in place underground. The resulting gas is mainly hydrogen and carbon monoxide, with impurities that .must be removed before further processing by one of the following routes.

Jan 1, 1959

By Howard A. Perko, M. Mae Benvenga, Heather H. Trantham

Displacement of soil and groundwater during helical pile installation can produce excess pore water pressures (PWP) in fine-grained soils. Pore water pressure reduces effective stress in the soil immediately adjacent to the helical pile shaft and near the helical piles. Previous studies have shown generation of PWP may affect the capacity to torque ratios of the helical bearing elements. Large diameter helical piles that generate much of their torque and capacity from shaft adhesion are affected by PWP and therefore exhibit significant pile "freeze" after installation. Computer modeling is used herein to evaluate PWP immediately adjacent to helical pile shafts during installation in various soil types. The models show the degree and distance from the shaft that is influenced by PWP during installation and the amount of time required for the PWP to dissipate. Pile freeze has been measured on several project sites by re‐torque measurements. These re-torque data are compared with computer modeling and correlations between saturated hydraulic conductivity and dissipation time are presented and discussed. INTRODUCTION Helical piles are full-displacement piles, meaning installation does not produce drill spoil. Soil is displaced laterally as the pile progresses into the ground. This displacement of soil causes an increase in PWP, which reduces adhesion between the pile and the soil. For helical piles with small-diameter shafts, adhesion contributes little to the overall capacity and torque of the pile, so PWP changes are not typically considered in determining pile capacity. In modern construction, the use of larger diameter helical piles has become very common. For large-diameter helical piles, changes in PWP immediately adjacent the shaft can be quite large during installation. Increased pore water pressure and reduced adhesion can have a temporary effect on pile capacity and installation torque.

Jan 1, 2018

By Reno M. Pappas, Christopher Mark

This report presents results of a U.S. Bureau of Mines study of longwall gob material. The objective of this work was to determine material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining. Photographs of actual mine gob were digitized to obtain approximate particle size gradations of gob material. The gradation curve was shifted down to a lab- oratory scale, and 20 uniaxial compression tests were conducted. Varying the maximum particle size was not found to affect the stress-strain behavior, but changing the gradation appeared to influence the stress-strain behavior. The stress-strain relationship of the simulated gob material was nonlinear, the stress-secant-modulus relationship, was approximately linear, and the stress-tangent-modulus relationship was approximately a second-order polynomial function. Equations were generated from these curves, providing numerical modelers with a means to estimate gob moduli based on the stress level. In addition, the experimental data were statistically evaluated using multiple regression analyses, producing a series of equations to predict the secant and tangent moduli from the given stress level, bulking factor, rock strength, and thickness-to-width shape ratio of the particles.

Jan 1, 1993

By M. J. McLeod, S. Watters, G. G. Lutes, S. Castonguay

"Gold-bearing mineralization at Anomaly A occurs in polydeformed Ordovician turbidites of the Kendall Mountain Formation of the St. Croix belt in southwestern New Brunswick, and is hosted by WSWtrending, shallow-dipping, brittle-ductile high-strain zones associated with the latest stage of the second of four regional deformation events. Gold-bearing syn-deformational stockwork, massive, and multiply brecciated quartz-sulfide veined zones form irregular pods and sheets up to several meters thick, which contain arsenopyrite, pyrrhotite, pyrite, stibnite, and a variety of rare minerals that are gold-bearing. Mineralized zones are enveloped by locally auriferous, weakly to intensely altered wall rock. Vein paragenesis includes: (1) early (pre- to syn-D2) quartz-chlorite veins that are largely the product of migration of quartz by pressure solution; (2) crosscutting, multiphase, vuggy quartz-sulfide veins that contain most of the gold and are interpreted to be structurally controlled; (3) late, crosscutting, nondeformed, non-gold-bearing veins containing laumontite, chlorite, muscovite, quartz, fluorite, and base metal sulfides. Carbonate-poor alteration associated with zones of gold mineralization is lithology-specific, and appears to reflect overprinting of multiple events. Major elements removed during alteration include Si, Na, Mn, and Mg. The minor and trace elements removed include Co, Li, Sc, and possibly Sr, Ni, and Zn. Minor and trace elements added include Au, Ag, As, Sb, S, and possibly F, Cu, Pb, and Zr. On the basis of proximity, time constraints, and a similar ore mineral assemblage, gold mineralization at Anomaly A is interpreted to be a distal equivalent of the intrusion-related gold mineralization at the nearby Clarence Stream Main zone deposit. La minéralisation aurifère de l’Anomalie A se trouve dans des turbidites Ordoviciennes polydéformées de la Formation de Kendall Mountain, dans la ceinture de Ste-Croix du sud-ouest du Nouveau Brunswick, où elle est contenue dans des zones de déformation fragile-ductile à faible pendage de direction OSO associées au dernier stade du second de quatre épisodes de déformation régionale. Les zones aurifères syn-déformationelles se présentent en forme massive, de stockwork, ou de veines de quartz-sulfure bréchifiées à répétition formant des lentilles irrégulières et des couches de plusieurs mètres d’épaisseur contenant de l’arsénopyrite, de la pyrrhotite, de la pyrite, de la stibine, ainsi que divers minéraux aurifères rares. Les zones minéralisées sont entourées d’une enveloppe de roches faiblement à intensément altérées, localement aurifères. La paragénèse des veines comprend : (1) des veines précoces de quartz-chlorite (pré- à syn-D2) qui sont principalement le produit de la migration du quartz par solution-pression; (2) des veines polyphasées de quartz drusique et de sulfures contenant la plus grande partie de l’or, celles-ci sont considérées comme étant sujettes à un contrôle structural; (3) des veines tardives stériles, sécantes et non déformées contenant de la laumontite, de la chlorite, de la muscovite, du quartz, de la fluorite et des sulfures de métaux usuels. Les zones de minéralisation aurifère sont associées à une faible altération en carbonate contrôlée par la lithologie et semble résulter de la superposition d’événements multiples. Les éléments majeurs perdus durant l’altération sont le Si, le Na, le Mn et le Mg. Les éléments mineurs et traces perdus durant l’altération sont le Co, le Li, le Sc et possiblement le Sr, le Ni et le Zn. Les éléments mineurs et traces enrichis comprennent l’Au, l’Ag, l’As, le Sb, le S et possiblement le F, le Cu, le Pb et le Zr. Étant donné sa proximité géographique, les contraintes temporelles et les similitudes de leurs assemblages minéraux, la minéralisation aurifère de l’Anomalie A est interprétée comme un équivalent distal de la minéralisation aurifère associée aux intrusions du gisement avoisinant de la zone principale (Main"

Jan 1, 2008