Search Documents

By Adam Zanker

Smooth roll crushers are widely used as secondary crushers, operating most effectively when set for size reductions in a ratio between 3 or 4 to I. The feed supplied to these units varies from 13 to 102 mm in size and the product obtained ranges from 13 mm to about 20 mesh. Smooth roll crushers produce very few fines and absolutely no oversize. The diameter otfhe rolls varies with the clearance between them, feed size, and the coefficient of internal friction ofmaterial to be crushed, Detailed calculations of this relationship may be found in Unit operations of Chemical Engineering, (McCabe, W. L., and Smith, J. C., 1967, McGraw Hill, NY, Chapter 26, pg. 825). The geometrical arrangement of the roll crusher is shown on the accompanying sketch. A relatively simple relationship between the diameter of feed, the roll, and the gap between them is as follows:

Jan 6, 1980

Temperature Sensitive Polymers as Efficient and Selective Flotation Collectors

Sep 13, 2010

By I. S. Parrish

One of the most common errors uncovered while performing a reserve, or resource, audit is not in the geological modeling or grade problems due to poor sampling, prepartion or assaying. The error most commonly found is in tonnage or, more specifically, in the tonnage factor - that factor applied to volume to derive tonnage. Tonnage factors In the metric system, the tonnage factor is the density, or specific gravity. Specific gravity (Sp.g.) is defined by Dana (1947): • "The specific gravity of a mineral is the ratio of its density to that of water at 4° C (39.2° F). • "Density is the mass of the unit volume or weight of the body divided by the weight of an equal volume of water." When Sp.g. is multiplied by the metric volume it yields metric tonnes. In the English system, the tonnage factor is usually expressed in cubic feet per short ton (cu ft/st). When the volume in cubic feet is divided by cu ft/st, the resulting figure is in English short tons. Table 1 gives the cu ft/st factors equivalent to specific gravities from 1.6 Sp.g. to 5.8 Sp.g. The table is based on the following equation: cu ft/st = 0.9072 divided by Sp.g. times 0.02832 The blase attitude that most geologists have toward tonnage factors is echoed in the prevailing definitions of Reserves and Ore, as provided by the US Securities and Exchange Commission (S.C Form S-18), Canadian National Policy 2A and the SME Proposal for Reporting Terminology (SME February 1991). In each case, it is stated that "quantity" (SEC, SME), or "tonnage" (Can.2A), "is computed from dimensions revealed in...." etc. Unfortunately, "dimensions" do not directly yield tonnage. Dimensions must be factored by density to derive tonnage.

Jan 1, 1993

By T. I. Nelson

Natural aggregates, primarily stone, sand and gravel, are recovered from widespread, naturally occurring mineral deposits and processed for use primarily in the construction industry. They are mined, crushed, sorted by size, and sold either loose or in concrete products to build roads, houses, buildings, and other structures. Smaller quantities are used in agriculture, cement manufacture, and industries employing chemical and metallurgical processes. The growth of cities, their buildings and the highways that connect them have created demand for enormous quantities of aggregates. The aggregates industry is the largest mining industry in the United States in terms of production by weight, volume and by number of active operations.

Jan 1, 2005

The Earth Moving Equipment Safety Round Table (EMESRT) was established by mining companies in 2006 to influence manufacturer's equipment design through a process of engagement. 2010 EMESRT member companies include Anglo American, Barrick, BHP Billiton, Centennial Coal, Collahausi, Newcrest, Newmont, Rio Tinto, Vale and Xstrata.Driven by a persistent need for retrofits to new equipment, such as haul trucks, EMESRT initially engaged with Surface Equipment Manufacturers including Caterpillar, Komatsu, Leibherr, Hitachi, Le Tourneau and Terex. These OEMs responded positively to the EMESRT initiative, welcoming the opportunity for dialogue with an aligned industry regarding human factors issues related to equipment design, rather than needing to respond to the disparate range of demands for design modifications previously received from individual customers. This engagement process is about making global sustained changes within the OEM organisations and within the mining companies. It is a very international exercise. For example, over two weeks in September 2010, a total of 21 different miners from ten different companies travelled from Australia, South Africa, Canada, Brazil, Singapore and the United States to engage with OEM counterparts who assembled from the United States, Japan, France, Sweden, Finland and Germany. EMESRT Surface Group representatives completed a whirlwind tour of the major North American manufacturers of mining equipment. Starting in Dallas (Atlas Copco, LeTourneau), this tour passed through Gainesville (Sandvik), Newport News (Liebherr), Guelph - Ontario (Hitachi) and Milwaukee (P&H Mining/Joy Global; Bucyrus), before winding up in Peoria, Illinois (Komatsu, Caterpillar). Over nine meetings, this group engaged with 129 individuals from nine OEMs. The EMESRT group welcomed miners from four non-member companies to come along for the meetings. These companies are Syncrude Canada Ltd, the Kearl Oil Sands Project - Imperial Oil (ESSO), Suncor Energy Ltd and Teck Resources Ltd.Other mining industry sectors have now expanded the EMESRT scope from surface mining to include exploration and underground mining equipment. In 2009, EMESRT was organised into four Technical Groups, consisting of EMESRT member company representatives, to focus on engagement with OEMs of surface, underground coal and soft rock, underground hard rock, and exploration drilling equipment. An advisory group has been formed to coordinate activities between all workgroups and provide strategic direction and cohesion between all activities. The Minerals Industry Safety and Health Centre (UQ-SMI) facilitates and coordinates all EMESRT activities on behalf of member companies. Building on successes with individual Surface Mining OEMs, EMESRT now aims to help OEMs in their transition to a sustainable design process that will incorporate and address specific design philosophies at the concept phase of design, so that significant improvements can be made up front for little cost within the overall budget. EMESRT members plan to educate all stakeholders, internally, within their own companies, and externally, by addressing industry associations, regulators and other end users about new ways of evaluating equipment design based on EMESRT purchasing specifications. This presentation will outline the EMESRT approach and report on progress in 2010.

Dec 6, 2010

By F. R. Morral

INDUSTRY has yet to find a universal solution to the problem of engineer personnel selection. Today, the choice of the right man for the right job is even more pressing than ever before. The age of the hard apprenticeship seems to have passed. In its place one finds the interviewer who must determine through personal contact and evaluation of college grades whether a graduate engineer will fit into his company's scheme. The problem, as it is constituted today, may be broken into four parts: Need for better use of human resources (there is a shortage of engineers, scientists, and skilled workers), productivity with higher efficiency, encouragement of personal pride in work performed, and employee's happiness on the job and away from it.

Jan 4, 1953

By F. W. Bradley

MY first Nevada City mining reminiscence is one of seeing Capt. Thomas Mein, over 52 years ago, in the old Wyoming mill on Deer Creek about a mile below the town of Nevada City. Captain Mein was then superintendent of the Wyoming mine, where the old fashioned Cornish pump was used, as well as hurdy-gurdy water wheels for power. This mill was one of the typical, up-to-date mills of that time and consisted of stamps, fed by Chinese hand feeders, who also cobbed the ore down to a small enough size to be fed into the mortars. Stamps at that time were of light weight and crushed about one ton to one and a half tons to the stamp, the pulp going over plates, then into sluices with self-raising gates. When a sluice became full the pulp was shut off and directed into the parallel sluice, also with a self-raising gate. The concentrate thus collected in the sluice was shoveled out and carried to Cornish buddles and there cleaned up, preparatory to being sent to a local custom chlorination works.

Jan 1, 1929

By Kazuya Naito, Nobuyuki Okamoto, Natsumi Kamiya

JOGMEC (Japan Oil, Gas and Metals National Corporation) became the first entity to sign an exploration contract for Cobalt-rich Ferromanganese Crusts (Crusts) with the ISA (the International Seabed Authority). The contract was signed on 27 January 2014, and 15 years exclusive rights for exploration activities had started in the contracted area, located in the North-Western Pacific Ocean. JOGMEC had already conducted basic scientific surveys around the contracted area from 1987 to 2012. Activities by JOGMEC that will be undertaken during the first 5 years of the contract include examination of geological and acoustic surveys, environmental baselines surveys, and undertaking basic studies of R&D in mining, processing, and smelting technologies. Geological surveys will include analysis of rock core samples, using BMS (Benthic Multi-coring System). Deep-towed TV Camera will be used to estimate the distribution of crusts deposit and to get basic environmental data of deep-sea megabenthos. Water sampling, marine sediment sampling, and installation of mooring systems on the seafloor will also be conducted as a part of environmental surveys.

Sep 1, 2014

By A. W. Czarnowsky

More than ever before, mining projects are besieged from growing regulatory, political, public, and special interest group pressure. Administrative and legal appeals to permits and environmental documents can delay project start-up and add tremendous cost to mineral development. Some mining projects have been canceled given undue external constraints. Successful managers must learn to cope with these constraints. This paper will discuss controversy and present a number of environmental management tips to minimize the potentials for delay and to lessen the impacts from government and anti-mining pressures.

Jan 1, 2001

By F. F. Roberto, E. Kirby, A. R. Marchbank

The application of biologically assisted methods for metal extraction in the mining industry has a long history, but development of modern techniques has been relatively slow. There is, however, a resurgence of interest in the industry with the recent development of methods to successfully treat base metals concentrates. Two major pilot plant programs for treatment of chalcopyrite concentrates have been initiated in the past year and results from one are beginning to be released. This paper provides an overview of methods that have been applied in the past, from the earliest deliberate applications of the technology, through the copper and uranium heap and dump leach applications, the more highly engineered agitated tank leach gold applications and the developments currently taking place in the industry.

Jan 1, 2003

By A. R. Miller, G. Desrivières, M. C. Bétournay, D. L. Barnes, P. Laliberté

"Over the last four years, an international initiative, championed by Vehicle Projects LLC, the Fuelcell Propulsion Institute and Natural Resources Canada, has been active in carrying out research projects to prove out the concept of applying fuel cell technology to underground mining vehicles. These have been carried out by a consortium consisting of mining companies, equipment manufacturers, technology developers, national laboratories and consultants, with the participation of Canadian and U.S. mine regulatory agencies.This clean technology, which produces only water and electricity, would allow several advantages to be obtained, in the health area (by eliminating diesel emissions and reducing noise generation), in lowering production costs (such as reducing ventilation required) and lowering greenhouse gas emissions.This paper outlines the results obtained in several key areas, such as, the operation of fuel cells in underground conditions, risk issues related to underground and surface operation of hydrogen vehicles and hydrogen production and delivery systems, and the design and mining performance of the world’s first hydrogen mining vehicle, a mine production locomotive. The work to date on the fuel cell loader, designing the power plant and power transmission systems, operational requirements, and operating cost reductions is also presented."

Jan 1, 2003

By P. Tong-jiang

We studied mineralogical characteristics of the vermiculite samples from seven mines in China. We found three types of interstratified structures in the investigated samples: 1:1 regular interstratified structure, segregated interstratified structure, and random interstratified structure. The vermiculite samples from six mines are mainly composed of phlogopite?vermiculite interstratified minerals, and the samples from the other mine are composed of chlorite?vermiculite interstratified mineral. The samples with phlogopite?vermiculite structure have high contents of K2O, TiO2 and Na2O. The samples with chlorite?vermiculite structure have the highest contents of MgO and Al2O3. The cation exchange capacity of the samples is 17.3?99.0 mmol/100g.The exchangeable cations of phlogopite?vermiculite samples from Weili Mine mainly include Na+ and Ca2+, while those of phlogopite?vermiculite samples from Tongguan Mine mainly include Mg2+ and Ca2+. The thermal expansion ratio of the samples is between 9 and 32. The exfoliated vermiculite products from Weili Mine have the best mechanical strength.

Feb 27, 2013

By José Dávila

El presente trabajo señala el programa de manejo de datos del monitoreo biológico aplicado en BHP Tintaya. El estudio informa sobre el estado actual de las variables del medio natural, tales como la flora y la fauna, así como sus características temporales y espaciales para así diseñar las soluciones a los riesgos e incidentes ambientales referidos a ecosistemas naturales. Asi también, la investigación se complementa con el monitoreo de suelos, aguas, aire y residuos de diverso tipo, al reconocer que las actividades mineras se efectúan inmersas en medios naturales. Por lo que las empresas mineras , están obligadas a proteger el equilibrio y adecuado funcionamiento de los ecosistemas naturales.

Sep 13, 2001

By F. K. McKean

Introduction The present paper may be considered as a sequel to a paper, A Process for Cleaning Molybdenite .Concentrate, which was presented by the author at the annual meeting of the Institute last year. In that paper, a description was given of the laboratory work leading up to the adoption of a new process for treating complex molybdenite ores of the Molybdenite Corporation of Canada. A bare outline of mill performance with the new flow-sheet was included. With this writing, the purpose is to describe the highly interesting work of translating laboratory experience into mill practice, to show what changes were required in design to put the scheme on an operational basis, and to point out the gratifying improvements in mill products which resulted from the new procedure. The process has been placed in operation at the La Corne mine of the Molybdenite Corporation of Canada. This mine was operated during the war by Wartime Metals Corporation, and, earlier, by the Molybdenite Reduction Company, which installed a small plant. The property is situated on the highway from Amos to Val d'Or, Quebec. The claims held by the Company are at the boundary between La Corne and Vassan townships.

Jan 1, 1947

By M. A. Rabah

This paper focuses on the separation and extraction of lead and zinc from Egyptian ore at the Eastern Desert close to Red Sea. The ore sample contains cerussite, galena, hemimorphite and other impurities. Experimental program includes flotationof galena using xanthate collector and cerussite using oleic acid as collector and sodium silicate to depress hemimorphite tailing. Galena, and hemi-morphite are converted to carbonate with sodium carbonate prior to metal extraction. Lead and zinc are extracted pyrometallurgically at 1050°C and750°C or electrochemically respectively. The overall performance of the applied method amounts to 99.2%. Extraction efficiency of lead and zinc amounts to 98% and 94.5 % respectively. A model assumed that galena and cerussite in the ore are partially oxidized and can be liberated by grinding. Oleic acid selectively reacts with cerussite in a multistep sequence. Preliminary cost estimate shows that the price of the products is competitive to their local market prices.

Jan 1, 2000

By Ludwig M. Strah

"Wear is a universal problem and is present in all cases wherein one weighted surface moves with or relative to another surface. A practical description of wear as applied to mineral processing plants is outlined.With the advent of higher material and maintenance costs, more attention is being focused on the field of wear resistant linings. The aforementioned is magnified today as the production facilities continue to be designed to handle larger daily capacities. These changes, higher costs and larger plant handling facilities have necessitated the introduction of different materials and designs to combat the never ending battle against wear.In order that wear be understood, it can be relegated to two specific types:1 - Mechanical Wear - due to movement of one loaded surface relative to another.2 - Chemical Wear - more easily defined as corrosionMechanical wearMechanical wear can be subdivided into two basic forms:A.,Material movementB.,Material impactMaterial movement Abrasion is the result of, as earlier stated, the straight move¬ment of one loaded material relative to another.Material impact Is the striking effect when a mass strikes another from various angles and at various speeds. Impact can be severe enough to permanently damage and distort the basic component installed to overcome impact."

Jan 1, 1983

By C. K. Man

Coal dust explosions in underground coal mines are prevented by generous application of rock dust (usually limestone). If an explosion should occur, the rock dust disperses, mixes with the coal dust and prevents flame propagation by acting as a thermal inhibitor or heat sink. To investigate this process in more detail, a number of explosion experiments using various coal dust and limestone rock dust mixes have been carried out at the Lake Lynn Experimental Mine (LLEM). These were conducted in a single entry of about 1600 ft (488m) in length and initiated with a methane gas explosion. A consistent set of post-explosion floor dust samples were taken along the entry after each test. These dust samples have been analyzed in the laboratory using thermogravimetric analysis (TGA) and solubility to determine how the limestone rock dust behaved during the coal dust / rock dust explosions. The preliminary results are reported in this paper and indicate that the chemistry of limestone plays an important role in its capacity to inhibit coal dust explosions. The results also show that it may be possible to estimate the intensity of the explosion using these conventional methods of analysis. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By J. J. Geldenhuys

A colloquium on 'Developments in the Mechanization of Mining Operations' was held in, conjunction with the 1984 Electra Mining Exhibition, at the Milpark Holiday Inn in Johannesburg on 19th September, 1984. An attendance of close on 200 delegates was testimony to the popularity of the subject. The delegates included a number of visitors from abroad, including senior members of the management of foreign companies and a member of the Council of the Institution of Mining and Metallurgy, United Kingdom. Both the local and foreign press was also represented.

Jan 1, 1985

Jan 1, 1957