Search Documents

By Shi Hongchao, Zou Zou Xinkuan, Zhang Jichun

As drilling and blasting is carried out in an urban tunnel, which is adjacent to an existing building or structure, the balance between blasting-induced vibration reduction and drivage efficiency is a most important issue that must be resolved properly. Therefore, a new cut blast method named Stepped V-cut millisecond blasting (SV-cut) was developed by optimizing the most common used Vertical V-cut blasting method (V-cut). The most significant features of SV-cut lie in the utilization of sublevel interval charging structure and millisecond delay blasting technology in cut hole and the cut-cavity formed from outside to inside sequentially. SV-cut provides advantages of high borehole using ratio, low vibration level, and satisfied advance per attack. Based on the principal of millisecond blasting, the rock fragmentation process and the vibration reduction mechanism of SV-cut are analyzed. Determining methods of blasting parameters, which do have significant effect on vibration intensity and cut-cavity formed quality, are proposed according to the forming requirement of both outer and inner cut-cavity and vibration reduction. In order to compare the performance between SV-cut and V-cut, field blasting experiments were performed in the blasting engineering of Yamalike twin-arc tunnel, which closely passes over aged parallel tunnels. Blasting results show that SV-cut blasting is proven as an effective tunnel blasting method for both increasing blasting effects and decreasing blasting vibration. Comparing SV-cut with V-cut, the SV-cut can increase blasting drivage about 8.5% and reduce the vibration intensity induced by cut hole blasting 30% at least.

Jan 1, 2015

Various reagents are added to flotation pulps to manipulate the chemical environment in order to create favourable conditions for the separation of the desired mineral from the unwanted gangue. Interactions occur between these reagents and between the other chemical parameters existing in the flotation pulp which complicate the elucidation of the behaviour of the respective reagents. This paper discusses the roles of the main classes of reagents added viz. collectors, frothers, depressants and activators, as well as the interactions between frothers and collectors. A case study reporting synergistic interactions between thiol collectors in the flotation of pyrite at pH = 4 is included. The use of Potassium n-butyl xanthate (PNBX) and a dithiocarbamate type collector (DTC) were tested both as pure collectors and as components in a collector mixture. In the batch flotation tests sulphur recovery and grade, water recovery, rate of recovery and image analysis of the surface froth were used to evaluate the effect of the mixture on the overall flotation performance. Bubble loading tests showed that the use of the mixture improved the efficiency of the particle collection process by bubbles. Thermochemical measurements of the adsorption of the collectors onto the mineral, indicated the formation of different surface products by the two collectors.

Jan 1, 1998

By R. H. Grau, S. B. Robertson, F. Garcia, A. C. Smith, T. P. Mucho

Researchers working for the National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory are developing ways to protect the health of miners. Part of that effort is devoted to improving the air quality in underground stone mines by developing ventilation techniques that can be used in these types of operations. The air quality in these large opening nonmetal mines can be significantly improved by using diesel particulate matter (DPM) controls along with sufficient ventilation quantities to remove contaminants. Practical methods of ventilating these underground stone mines can be accomplished by using mine layouts that course and separate ventilation air through the use of stoppings. The design, construction, and maintenance of effective stoppings in large openings have been a real challenge to mine operators. Several different types of stoppings have and can be used for this application. The choice of stopping design, material used, and construction techniques should be dependent upon a number of factors such as the intended life and effectiveness desired.

By Sharpin P. C

The countercurrent gas-solid heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temperature distributions through the drier have been calculated. Although the calculations rest on several simplifying assumptions, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating conditions on the rate of drying of the briquettes which controls the strength of the char produced. The analysis shows why a limitation was reached in the improvement of char strength in the pilot plant in 1961 due to the performance of the drier and a prediction is made of a way in which the limitation could be overcome.

Jan 1, 1966

This Bureau of Mines report is devoted to descriptions of investigations pertaining to underground mine trailing cables, their handling, splicing, and the use of couplers.

Jan 1, 1979

By Z. J. Hladysz

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, South Dakota, under the sponsorship of the National Science Foundation (NSF) in cooperation with the Department of Energy (DOE). This national facility will host a variety of multi-disciplinary science and engineering experiments including physics experiments that require shielding from cosmogenic radiation. Current plans include construction of large rooms (up to 55 m in width) at depths of 1.48 km (4850 ft) and 2.25 km (7400 ft) below the surface. Preparation of the preliminary design required the development of a geotechnical characterization program including: preliminary drilling and coring, core logging, drill hole mapping with a televiewer, drift mapping of the geology and rock structure, in-situ stress measurements, and laboratory testing of the mechanical properties of the rocks and discontinuities. Overall rock quality is very good to excellent. Site investigations were followed by geotechnical assessments for the construction of caverns and laboratory modules. The results are favorable and reaffirm selection of the Homestake site for establishment of a Deep Underground Engineering and Science Laboratory.

Jan 1, 2011

By G. S. Hansford, C. J. N. Dempers, G. E. Searby, A. W. Breed, M. A. Jaffer

The bioleaching of sulfide minerals involves a ferric attack of the mineral with the role of the micro-organisms being the oxidation of the ferrous-iron back to the ferric form, and the oxidation of sulfur, either via thiosulfate or polysulfides, to sulfate. The kinetics of bacterial ferrous-iron oxidation and the chemical ferric leach kinetics of sulfide minerals can both be described as functions of the ferric/ferrous-iron ratio. The independently determined bacterial ferrous-iron oxidation and chemical ferric-iron leaching kinetics have been successfully used to predict continuous bioleaching operations.

Jan 1, 2000

By P. G. Flood

A simplified conceptual model shows how the arc flank to arc fringe areas adjacent to ignimbritic centres form a prospective zone for natural zeolites. Large alkaline lakes that serve as the repository of voluminous ash-fall tuffaceous material provide the ideal chemical setting for pervasive alteration of silicic glass to zeolites. The unusually old age of the Escott deposit demonstrates that any silicic volcanic province that contains low-temperature, unmetamorphosed sequences is a potential zeolite exploration target and that age should not be used as a criterion to exclude potential areas. It has also been demonstrated that heulandite and mordenite, formed by diagenetic alteration of silicic glass, do not always change to analcite and albite through the ageing process

Jan 1, 1991

CrusherMapperTM - A New Tool for Crusher Condition Monitoring The efficiency of mineral processing plants is entirely dependent on the availability of the plant equipment critical path. This typically concerns comminution circuits consisting of primary crushers and primary grinding mills. Crusher and mill availability are determined by the frequency and duration of maintenance shutdowns, which are primarily driven by the need for replacement of sacrificial liners. The change of crusher and mill liner shape over respective life cycles also strongly affects plant efficiency. It is therefore highly desirable to accurately monitor the condition of mills and crushers in order to optimise plant efficiency through maximised availability and targeted liner shape. Traditional comminution liner and other production parameter condition monitoring has been attempted through ineffective methods which prevent satisfactory management of crusher and mill maintenance and reduce operational control. This situation has recently dramatically improved for grinding mills through the development and commercial deployment of MillMapperÖ, a technology based on three-dimensional laser scanning data and dedicated software (Franke, Lichti and Stewart, 2006; Franke and Lichti, 2007; 2008; Franke, 2008; Franke, Redman, Johnson and Michalek, 2009). At the time of writing in late 2009, MillMapperÖ is in successful use at a rate of approximately 170 surveys and associated reports per annum at processing plants in Australasia, South America, North America and Africa. This paper presents the introduction of CrusherMapperÖ, the MillMapperÖ equivalent for crushers. CrusherMapperÖ also utilises high density, high accuracy laser scanning data, and features dedicated algorithms for three-dimensional monitoring of wear on crusher concaves and mantles. This facilitates the detection of wear hot spots or zones or localised liner failures, and accurate forecasting of reline tonnages and dates. It also for the first time provides the means to establish optimised concave and mantle shapes in order to achieve production targets. In contrast to any other currently utilised condition monitoring method, CrusherMapperÖ data collection can occur remotely and does not require any shutdown or crusher isolation. This method therefore does not interrupt crusher production while at the same time eliminating any confined space risk normally associated with taking measurements inside the crusher cavity.

Sep 13, 2010

The mining industry continues to be a major driver of the Australian economy generating over A$130 billion in export earnings in 2008/2009. However, the industry has been cited as a significant contributor to green house gas emissions. Australia's proposed carbon trading scheme, the Carbon Pollution Reduction Scheme (CPRS) will financially impact on mining operations; this calls for a holistic planning approach for mining operations taking into account the impact of the emissions trading scheme. Since carbon trading is a new area of study, particularly within Australia, the quantitative effect of the CPRS on the mining industry is uncertain and current mine planning practices do not directly consider emissions. This paper presents results of the study into the impact of the CPRS on a hypothetical large scale open pit operation, using a spreadsheet model based on linear programming and simulation. By varying the production rates, life of mine (LOM), carbon price and ore grades among other variables several scenarios were simulated to determine the impact of emissions trading scheme on the net present value of the project. This study found that the adoption of the proposed Carbon Pollution Reduction Scheme could impact mining operations in Australia by a three per cent to six per cent reduction in net present value, for carbon credit costs of $25/t to $50/t respectively. While the six per cent reduction in net present value for a mining operation is significant, rising fuel prices have had a similar effect in recent years. The most energy-intensive processes are the milling circuit and the flotation concentrator circuit. These processes are jointly responsible for up to 60 per cent of the total emissions, depending on the production rate and the level of offshore processing conducted. Clearly, the introduction of the CPRS makes it is imperative for mining companies to assess the impact of carbon emissions on a mining project during mine planning.

Dec 6, 2010

By R. J. Matetic, J. S. Peterson, P. G. Kovalchik

The National Institute for Occupational Safety and Health (NIOSH) has initiated a study of a roof bolter to reduce noise exposure to mine roof-bolter operators. An important segment of this research entails determining the affect of various drilling configurations on the performance (penetration rate) and sound power emissions when drilling into granite. Test conditions included using various combinations of rotational speeds and thrusts, using 2.54- and 3.49-mm- (1- and 1 3/8-in.-) diameter hexagonal and round drill steels, using vacuum and wet conditions and using drill media of differing compressive strengths. This paper details the affects of each of these variables on the performance and sound power level emission. When drilling into granite, it was found that wet drilling generated lower sound power levels and performed better than vacuum drilling.

By Young-Dong Cho, Yonghun Jong, Dong-See Shim, Seokwon Jeon, Chung-In Lee

The most important operation in the tunnel blasting procedure is to create an opening in the face in order to develop more free surface in the rock mass. This operation is highly dependent on the cut holes. In general, the burn-cut or V-cut is commonly adopted to blast the cut section. But, these traditional methods often raise problems. There are instances (a) that the actual advance is considerably less than the designed advance depending on the rock mass, (b) that they cannot sometimes enlarge the free surface efficiently and (c) that the blast vibration resulted from the cut blast exceeds the allowable vibration level. In order to resolve the problems, many different kinds of the cut blast can be considered.

Jan 1, 2005

By A. M. R. Neiva

The WNW-ESE-trending hydrothermal veins cut alternating mica schists and quartzites of mainly Ordovician age and, to the west, a Hercynian muscovite-biotite granite. They have been prospected and developed to a depth of 300 m and reserves of 20 t Au estimated. The paragenetic sequence and chemical compositions of the ore minerals are generally similar to those at Jales to the south. Gold, electrum and aurian silver form inclusions in arsenopyrite, pyrite, galena, sphalerite, pyrrhotite and quartz and also occur in veinlets that cut these minerals. Silver has been found in gold, electrum, aurian silver, tetrahedrite, freibergite and the Ag-Pb-Sb sulphide owyheeite. Early arsenopyrite crystallised at an estimated 480 degrees C and the more common, later arsenopyrite in which Au and Ag are generally included at 430-300 degrees C. Sphalerite crystallised at 307-100 degrees C. Monoclinic pyrrhotite may have been formed by the inversion of hexagonal pyrrhotite at 248 degrees C

Jun 16, 1905

By Darrell Wilder

When designing excavation support systems in urban environments, it is often necessary to consider the effect of vertical surcharge loads from adjacent structures. Several methods are used in practice to establish the horizontal surcharge-induce pressure on the excavation support. According to the experience of the authors, these methods often seem to overestimate the effect of the surcharge and may have significant impact on the construction costs. This paper explores several of these procedures and provides a discussion as to the reasons for the differences in surcharge effect predictions between different procedures. It also provides practical recommendations for designers dealing with excavation support design.

Jan 1, 2006

By D. Malovichko

Seismic events and pillar failures observed in two platinum mines in the Rustenburg area, South Africa, were investigated. We studied the sources of approximately 300 largest seismic events recorded in 2009. Moment tensors of these events were estimated from amplitudes and polarities of P- and S-waves. The inverted mechanisms contain isotropic implosive components in many instances. Analyses of uncertainty of the moment tensor solutions confirmed the significance of the implosive component in general. Several documented cases of pillar failure were considered in detail. For each of these a seismic moment tensor was calculated from an elastic stress model assuming an instant removal of a failed pillar. The geometries and magnitudes of the theoretical seismic moment tensors are in agreement with the observed (i.e. inverted from seismic data). The results indicate that either pillar failure or fracturing in the proximity of the reef (within a fraction of the dominant wavelength of seismic waves) are responsible for a significant portion of the large events recorded in these mines.

Jan 1, 2012

By P N. Holtham

Magnetic separation is routinely used in the processing of titaniumminerals, and the efficiency of these operations can be determined bymeasuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved.This paper describes the development of an inductance-basedinstrument for measuring very low levels of magnetic susceptibilityon-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance.A prototype instrument has been installed in the zircon scavengercircuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction.Using the instrument, the zircon content of this stream can now beaccurately determined from the measured magnetic susceptibility,provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By W. Robert Thompson

Hurricane Katrina caused significant damage to transportation structures on the Gulf coast in August, 2005, including the destruction of the US 90 Bridge over Biloxi Bay, Mississippi. Part of the successful design/build proposal for the replacement bridge included a comprehensive test pile program of indicator piles and load test piles in the geotechnical investigation program. A total of 22 indicator piles were installed on the project using the pile driving analyzer to monitor the pile behavior. Five load tests were performed: two axial Statnamic, two lateral Statnamic, and one static axial. The results of the test pile program established driving criteria for production piles that included end-of-drive blow counts and pile tip elevations with an appropriate allowance for setup. The program also confirmed that the planned installation equipment and techniques of GC Constructors, a joint venture of Massman Construction Co., Kiewit Southern Co., and Traylor Bros., Inc., would install the piles to the design tip elevations before production piles began. An extensive program of restrike measurements at a range of times after initial driving of the indicator piles provided a systematic documentation of pile setup in the soil profiles on the site. These resistance values were used to develop a dimensionless setup factor ?S? as the ratio of the restrike resistance to the end of drive resistance. This factor varied from 1.5 for piles penetrating clays and tipped in sand to 3.0 for piles bearing completely in clay and helped establish an end-of drive blow count that included an allowance for setup. The CAPWAP analyses of restrike data with setup and the load test data were used to confirm the design unit side shear and end bearing values developed from the borings and static capacity calculations and to select the design pile lengths.

Jan 1, 2009

By John C. Machisak

THIS INFORMATION CIRCULAR contains injury and employment data for all stone quarries in the United States for the Calendar year 1960. This publication contains statistical data on injuries and employment pertinent to the stone quarries and related operations, such as the manufacture of cement and lime, rock dressing etc., but excludes statistics for clay and sand and gravel operations. Data for these commodities may be found in other Bureau publications. Reports received from the operators are voluntary responses to the Bureau's request for information; therefore, the figures may not be complete for the industry. However, since these data contribute greatly to the promotion of safety, every effort has been made to make them representative of the industry.

Jan 1, 1963

By John C. Machisak

THIS INFORMATION CIRCULAR contains injury and employment data for all stone quarries in the United States for the Calendar year 1960. This publication contains statistical data on injuries and employment pertinent to the stone quarries and related operations, such as the manufacture of cement and lime, rock dressing etc., but excludes statistics for clay and sand and gravel operations. Data for these commodities may be found in other Bureau publications. Reports received from the operators are voluntary responses to the Bureau's request for information; therefore, the figures may not be complete for the industry. However, since these data contribute greatly to the promotion of safety, every effort has been made to make them representative of the industry.

Jan 1, 1963