Search Documents

By M. A. Hermanus

This paper examines the occupational health and safety performance (OHS) of the South African mining sector against the backdrop of changes in the composition of the sector, international trends in OHS performance, and the agreement on OHS milestones and targets by mining stakeholders at the Mine Health and Safety Summit of 2003. Although OHS performance has improved, progress is slow and there is need for significant rather than incremental change if the targets are to be realized. Since 2003, fatalities and injuries are 20?25% short of annual milestones and not all commodities show consistent improvement. Statistics on occupational health impacts are unavailable, but noise and respirable dust levels are known to be high in mines, with much work lying ahead to address exposures at source. Trends in regulating and addressing OHS hazards are discussed with reference to the notion of ?systems-thinking? and the targets. Efforts to improve OHS and to respond to changes in the sector are constrained by a lack of training and consistency in risk management, guidance for junior, small and artisanal miners, and holistic approaches to risk. For example, treating risk holistically would involve taking proper account of contractors and women in the workplace, and attending to human factors and ergonomics.

Jan 1, 2007

By John P. Hager

A special inlet system has been developed for a TOF mass spectrometer that allows the equilibrated high-temperature vapors from an atmospheric-pressure flow reactor to be leaked into the ion source of the mass spectrometer without undergoing any compositional changes. Using this flow reactor - mass spectrometer system and a modified transpiration system (one that allows for the carrier stream to be equilibrated with two different condensed samples) a series of fundamental vapor transport studies were undertaken. The results of these studies are summarized as follows: 1. The vapor species in equilibrium with condensed copper (I) chloride were determined to be Cu3C13, Cu4C14, and Cu5C15. The gas mixture is fifty percent tetramer near the melting point (703°K), with the percentage of tetramer decreasing with increasing temperature. The following thermodynamic results were obtained.

Jan 1, 1977

By C. G. Anderson

"As demand for copper and precious metals continues to grow, the need to develop new supplies increases. In the imminent future, the new large global ore bodies are more complex, with enargite, tennantite and tetrahedrite as the abundant contained mineralogy. These resources also contain considerable gold and silver. As such, direct treatment by conventional smelting is prohibitive due to the potential environmental impacts and copper quality issues. This paper outlines the effective application and associated economics of industrially proven Alkaline Sulfide Leaching (ASL) hydrometallurgical technology to an enargite concentrate for selective removal and recovery of arsenic, antimony, gold and silver, leaving a clean high-grade copper concentrate. The fundamentals behind the technology are described, along with those of hydrometallurgical arsenic fixation and stabilization. Flowsheets and unit operations are elucidated, along with an in-depth economic analysis. INTRODUCTION Hydrometallurgical methods can be employed for treatment of gold-, arsenic-, antimony-, tin- and mercury-containing materials, concentrates and ores, as well as complex ones containing any number of metals (Conner & Anderson, 2013). The alkaline sulfide leaching (ASL) system is one of these. It is essentially a mixture of sodium sulfide and sodium hydroxide with other meta-stable alkaline species as required. This is a unique hydrometallurgical system beause it is a very selective lixiviant for the distinct leaching of tin, gold, antimony, arsenic, tellurium, silver and mercury (Anderson, 2000, 2001a, 2001b, 2002, 2003, 2012, 2014; Anderson & Twidwell, 2008a, 2008b, 2010; Anderson et al., 2004, 2005; Glazkov & Tseft, 1961; Gnatyshenko & Polyvyanni, 1961; Nadkarni et al., 1975; Nadkarni & Kusik, 1988; Polyvyanni, 1963). Worldwide, ASL technology has been employed industrially in the former CIS, China and the United States for the production of antimony (Anderson et al., 1992, 1994; Anderson & Krys, 1993; Holmes, 1944; Kaloc, 1967; Nordwick & Anderson, 1993; van Stein, 1971)."

Jan 1, 2015

By M P. Simpson, J L. Mauk

The Golden Cross, low-sulfidation, epithermal deposit shows a number of features that are directly or indirectly related to boiling hydrothermal fluids. Occurrences of lattice calcite and their quartz pseudomorph equivalents in veins, and occurrences of adularia in veins and in the surrounding altered rocks in the vicinity of ore, are both direct evidence of deposition in the presence of boiling hydrothermal fluids. Loss of carbon dioxide causes calcite deposition (platy variety) near the level of first boiling, while adularia deposits due to the attendant pH increase along the cooling flow path. Indirect evidence of boiling include crustiform-colloform quartz banding, late massive calcite veins, clay-carbonate alteration in the shallow and peripheral parts of the ore zone, and the restricted vertical interval of precious metal mineralisation. The colloform quartz banding strongly resembles the banding in amorphous silica deposits found in geothermal surface pipes. This implies that fluids ascending the Empire Vein structure were saturated in amorphous silica. If so, then they must have undergone phase separation, which initiated at considerable depth (e.g. =1000 m) and very hot temperatures (e.g. =300¦C). On the basis of stable isotope data, late massive calcite veins appear to have deposited from CO2-rich steam-heated waters. Calcite deposited along heating paths as these waters descended into the upflow zone during late stage collapse of the hydrothermal plume. In active systems, such steam heated waters form by deep boiling. The high CO2 contents of these waters promote hydrolytic alteration and the formation of clay-carbonate alteration. Reaction path modelling using CHILLER and a deep, Broadlands-Ohaaki water as an analogue, shows that minerals deposit along boiling flow paths over discrete spatial intervals. Calcite and adularia deposit near the site of first boiling, followed by gold and then by amorphous silica. For deep boiling starting at 300¦C, these minerals deposit over a path length that exceeds 1000 m. The distribution of banded quartz and gold at Golden Cross are consistent with such a boiling model. However, the elevation of first boiling must have fluctuated over 500 m to account for the coincidence of lattice quartz (pseudomorphs of platy calcite) and adularia, crustiform-colloform silica and gold over distances of a few centimeters in veins. We deduce that a downward propagating boiling front and expansion of two-phase flashing in a flowing water column occurred during episodes of high vertical permeability and fluid flux in the Empire vein structure.

Jan 1, 2000

By Brigitte J. Dejou

The Red Dog sediment-hosted zinc-lead deposit is located in the Brooks Range thrust belt in northwest Alaska, approximately 1000 km northwest of Anchorage. The mine constitutes the primary deposit in a 400 square kilometre district, which hosts several other mineral occurrences. All the known mineralisation is hosted by the Mississippian Ikalukrok Member, deep basinal shale of the Kuna Formation, part of a Devonian to Cretaceous sedimentary sequence. The rocks underwent intense deformation during the Brookian Orogeny in Middle Cretaceous time. Several thrust faults juxtapose the stratigraphy. The Red Dog mine is composed of four deposits which together contain 105 Mt in resources and reserves for a total resource exceeding 18 Mt of Zn metal. The mine is an open pit with 25 foot high benches. The biggest challenge is not the Arctic conditions, but metal extraction, due to the fine grained nature of the mineralisation and the variability of the ore. The mine produces Zn and Pb-Ag concentrates that are shipped to smelters around the world from the Red Dog port facilities during the short summer period. Ore mineralogy is generally simple and consists of sphalerite, pyrite, galena and marcasite. The deposits are generally overlain by decametre thick exhalative barite horizons and exhibit strong silicification, which locally obliterates the original textures. Although described as a world class Sedex-type deposit, a large portion of the mineralisation exhibits sub-surface replacement textures. Moreover, unlike most other Sedex deposits, the reconstruction of the basin is made difficult by the structural complexity of the district. To assist exploration in the district, several assumptions are made regarding the deposit settings relative to metal source, growth faults or crustal extension.

May 1, 2006

By Ron Board

"Probably the only thing that can he said about conveyor belt scales without fear of contradiction is that they have been responsible for as much or more puzzlement, argument and frustration than almost any other piece of equipment commonly found in ore processing facilities. To be sure, there are certainly a good number of satisfactory installations, some of these having been achieved through forethought and careful consideration in the early stages of plant design, while others seem to owl their success to what seems to be little more than good luck or white witchcraft; and it might also appear that black witchcraft or other gremlins are solely responsible for the poor performance of many belt scales that enjoy well-designed installations with apparently good operating conditions.This paper is intended to acquaint users with the major operational reasons why belt scales seem so fickle (and downright ornery too), and establish some reasonably simple test standards against which the performance of scale hardware can be measured. Then it shall be shown how the design flexibility of electronic scale systems can offer particular advantages in overcoming some of these everyday problems in a practical way, and without undue inconvenience to plant operations."

Jan 1, 1975

By John H. Fowler

"Most of the aggregate used in Nova Scotia is produced from numerous glaciofluvial and ice-contact deposits scattered throughout the province. Production from bedrock sources is increasing, with most of the coarse aggregate used in the Halifax-Dartmouth area coming from quarries operating within the metro area.A recently completed provincial sand and gravel inventory mapping program has identified some ""resource-poor"" areas where comprehensive aggregate evaluation programs are underway. Although some areas of the province are experiencing aggregate supply problems, large volumes are exported to markets as far away as Bermuda.IntroductionThe Nova Scotia Department of Mines and Energy has been involved with aggregate resource studies for several years, although sand, gravel and crushed stone are not designated as minerals under the Mineral Resources Act of Nova Scotia. Our role has been to provide the aggregate industry with resource data as well as provide similar information to governmental agencies involved with municipal planning, water resource studies and environmental protection regulations. Several private consulting firms use the information in many of their site development studies.We became involved with aggregates in a rather roundabout way. Several years ago, an outcry from inhabitants of a small coastal community over the removal of sand and gravel from a local beach moved the provincial Department of Lands and Forests to take action to protect provincial beaches. We were asked by the Department to provide information and to suggest alternative sources here operators extracting sand and gravel from beaches could relocate. This request initiated an aggregate inventory survey in southeastern Cape Breton, which was later extended to cover the entire province. The initial provincial sand z and gravel inventory survey provided a series of 1:50,000 maps showing the distribution of sand and gravel deposits in the province."

Jan 1, 1982

By Charles Barnhart

This paper is a discussion of the causes of deflagration in cast blasting and a description of a project intended to demonstrate how changes in six critical parameters contribute to the deflagration chemical reaction. Control of these parameters is key to solving the nitrogen dioxide “orange smoke” problem. Preliminary results of an investigation into the development of a technology addressing the problem of atmospheric releases of nitrogen dioxide during cast blasting in surface mine operations are described. The project is funded by a $600,000 Small Business Innovative Research grant from the National Science Foundation and an $80,000 Abandoned Coal Mine Land Reclamation Program grant from the state of Wyoming. The presentation will address the measures required to control the blast chemical reaction so that it does not produce nitrogen dioxide through deflagration. Experimental blast data will be focused on a new shaped charge detonation system designed to instantaneously bring the powder column to maximum velocity of detonation (VOD), thus insuring efficient detonation of the entire colulnn.

Jan 1, 2003

By J. W. Town

The Bureau of Mines determined the physical properties of southeastern Idaho phosphate fines as related to mineral composition, particle size and liberation, beneficiation, and potential use in structural clay products. The phosphate mineral in the fines was identified by unit-cell dimensions to be essentially the same as the phosphate mineral fluorapatite identified in the coarser sizes. The mean particle frequency as determined by electron-microscopy and pipet-analyses was between 0.5 and 0.2 micron. Liberation of the phosphate could not be definitely determined because of the weathered condition of the minerals and their extreme fineness. No beneficiation scheme was developed that would concentrate the phosphate into a marketable fertilizer product; therefore, forming and firing tests were made to demonstrate that the fines can be used to manufacture structural clay products.

Jan 1, 1968

By E. T. Turkdogan, P. Grieveson, J. F. Beisler

Jan 1, 1963

By S. J. Benson

The Harts Range deposit, owned by Olympia Resources is located some 130 kms northeast of Alice Springs, in central Australia (part of Australia’s Northern Territory). The core economic minerals here are industrial grade garnet and alumino magnesio hornblende (AMH). The resource contains an estimated 2.3 million tonnes of recoverable garnet and 6.2 million tonnes of recoverable AMH, making Harts Range one of the most significant abrasive medium deposits in the world. Part of the general marketing axiom of Olympia Resources is to make high quality products from the garnet and also a special series of blended garnet/AMH products to match the needs for other sectors of industry. The deposit mineralization is of alluvial origin and thus, requires no significant liberation regimes. Over 50% of the head feed is in the form of SiO2/quartz and as much as 17% is –63micron clay slimes and mica. Original pilot scale testwork for flowsheet development centred around fairly conventional wet gravity systems, with spiral concentrators being the pre-eminent separating device. To a point, this type of flowsheet was going to achieve some of the aims albeit fairly predictably. The one area that this circuit would be very limited though is in the recovery of the very coarsest of the medium SG minerals. This was going to be a very important and longer-term costly flaw. Amongst the highest demand, greatest value of products to be produced will be the range of garnet & AMH in the +600 microns sector. A flowsheet dominated by spirals would be fated to forfeit a significant proportion of these coarse minerals to tails. At the Outokumpu Technology P/L test facilities in Perth, testwork was conducted using a pilot scale Floatex® Density Separator, the LPF-230 model. Using a twin stage approach, whereby a primary Floatex® underflow reports directly to a secondary Floatex®, recovery of the economically important +600 micron garnet was increased from 65% in the spirals-only flowsheet to 95% using the Floatex® based flowsheet. Finally, the other significant aspect of this approach is in substantial simplification of the circuit required and a huge reduction in plant footprint. Also, the nature of using hindered settling provides substantial opportunities for process control and automation.

Jan 1, 2005

By Heikki Laurila, Sirkka-Liisa Jämsä-Jounela, Jarkko Karesvuori

"Artificial Intelligence includes excellent tools for the control and supervision of industrial processes. Several thousand industrial applications have been reported worldwide. Recently, the designers of the A1 systems have begun to hybridize the intelligent techniques, expert systems, fuzzy logic and neural networks, to enhance the capability of the A1 systems. Expert systems have proved to be ideal candidates especially for the control of mineral processes.As successful case projects, an expert system based on on-line classification of the feed type using neural data analysis is described in this paper. The essential feature of this expert system is the classification of different feed types and their distinct control strategies at the plant. In addition to the classification, the expert system has a database containing information about how to handle the determined feed type. This self-leaming database scans historical process data to suggest the best treatment for the ore type under processing. The system has been tested in the Outokumpu Finnmines Oy, Hitura mine. Other projects have been reported to be in progress.INTRODUCTIONIn the past ten years considerable researches have been done in the application of artificial intelligent methods in process industry. The technologies of fuzzy logic, neural networks and expert systems have received several thousand applications worldwide: monitoring and analysis of process operations, fault diagnosis, supervisory control, feedback control and scheduling and planning of operations. Recently, the designers of these systems have begun to hybridize these intelligent techniques to enhance the current capability of expert system. Complex signal processing, neural networks, fuzzy logic and rule-based systems are also implemented to develop new so-called smart or intelligent sensors, actuators or components. Field buses are playing a more and more important role in automation systems and in imbedded systems. The development of field buses has allowed the distribution of smart components over networks."

Jan 1, 2000

Several common ratios used for determining spontaneous combustion activity rely on comparing the amount of various products of oxidation with the amount of oxygen consumed to produce these products. As coal gets hotter, oxidation reactions become more efficient meaning more products produced for less oxygen consumed. There are many problems associated with accurately determining the true amount of oxygen used. These problems relate to the monitoring technique (and its associated uncertainties) used to generate the results, deficiencies in the established equations utilized in calculations, dilution with other gases and other sources of oxygen depletion. Typically the oxygen deficiency is over estimated, resulting in the under estimation of the indicating ratio. For this reason the use of ?one off? calculations to determine the status of the underground environment is not recommended. Instead trends of these ratios should be used to identify increases which indicate an increase in oxidation intensity. This paper outlines problems associated with the monitoring techniques and equations used to determine the oxygen deficiency.

Jan 1, 2009

By Julie Culverhouse, Dennis Grimm, Kieran Harding, Jean-Francois Boulanger

"Agrium’s Canadian Phosphate Business (CPB) is comprised of Kapuskasing Phosphate Operations (KPO) in Northern Ontario, Canada’s only operating phosphate mine, and Redwater Phosphate Operations (RPO) in Alberta, which manufactures the fertilizer from KPO’s concentrate.Production from KPO’s South Pit commenced in 2009 and introduced contaminant problems: high aluminium from crandallite and kaolinite clays. These issues caused a drastic decrease in P2O5 recovery and throughput in both plants. KPO attempted to reduce Al clays by means of aggressive desliming. Meanwhile RPO experienced high amounts of dissolved metals in their feed that are detrimental to fertilizer production.This paper covers the mineralogy of the problem, its impact on contaminant separation at KPO, on RPO’s process and on Agrium’s Canadian Phosphate Business as a whole.Potential solutions to the problem are discussed and analysed, including a process change to deslime high aluminium streams more aggressively and high grade ore flotation, which is atypical at KPO. The latter is a demonstration of the value of communication between the concentrator and the client, as KPO accepted a recovery loss and increased production costs in order to increase overall CPB profits. General lessons learned are discussed, followed by a section on ore blending.INTRODUCTIONAlthough the existence of the Kapuskasing phosphate deposit has been known since the 1970s, it’s only since 1999 that Agrium has been operating the Kapuskasing Phosphate Operations (KPO). The mine consists of three major pits (Center, North and South) from which a mining contractor hauls the apatite ore to the Agrium concentrator. The beneficiation plant processes the ore, separating contaminants such as Fe, Mg and Al which are detrimental to its client, Agrium’s Redwater Phosphate Operations (RPO). The KPO concentrate is finally thickened, filtered and dried before being shipped by rail to RPO.At the Redwater plant, the KPO concentrate is added to a sulfuric acid solution in an attack tank, to create a phosphoric acid solution and gypsum:"

Jan 1, 2011

The Objective: To reduce the noise generated by the exhausting air from a pneumatic roof bolting drill to a maximum of 90 decibels. Any attachment used for this purpose must be lightweight and must not cause a significant increase in back pressure. The Approach: Absorb the noise with a properly designed muffler that will permit sufficient airflow without affecting the normal operation of the drill. How It Works: The air exhausted by the drill enters the muffler through perforated disks into a resonator chamber. It then passes through a series of expansion and contraction chambers and is expelled to the atmosphere through another perforated disk. The basic muffler design for the pneumatic drill was established by using both digital computer analysis and experimentally simulated noise tests. The measured parameters used in the computer program consisted of inlet and outlet pressures, temperatures, airflows and exhaust areas. United

By Neil McMillan

"By any measure of common practice, Claude Resources' Seabee Gold Mine in Northern Saskatchewan should not now be operating. Not because reserves dwindled, or grade dropped or prices weakened or technical problems arose, but because a host of unimaginable other problems beset the project, any one of which would normally have led to the mine's failure.The success of the Seabee Mine, and it is extremely successful, is a story of the vision and blunt determination of two men. Neither is remarkable in his own right but each possesses the characteristics which were necessary to forge a highly productive and profitable narrow-vein mine in the midst of the most bizarre and unpredictable events which likely have ever beset a mine start-up in Canadian history.Together, Bill MacNeill, a Saskatchewan born, former bush pilot and Ray Gagnon, a big hearted, hard-fisted, miner with 44 years of experience in Canada's underground, built the Seabee Mine.They didn't accomplish this with brilliant geology, outstanding engineering or nimble corporate manouvering but rather a stubbornness and raw common sense which likely are all too often, ingredients missing in failed projects.The Seabee Mine is 100% owned by Claude Resources, a Saskatoon based company taken over by Bill MacNeill, its current chairman, in 1982. The company is listed on the TSE and produces 1200 barrels of oil per day and about 60,000 oz of gold per year. The company has a strong balance sheet, is very profitable and has 18 million shares outstanding.The Seabee property in Northern Saskatchewan started out like many other gold exploration properties in Canada.It was discovered in the l 940's by what is now Cominco, and, while highly regarded by that company the property sat largely dormant until acquired by Claude Resources in 1985.Claude did what most junior exploration companies would do and went looking for a company with a depth of expertise to joint venture the property.That company was Placer Development who could earn a 55% interest in the Seabee by delivering a bankable feasibility study on the Project by July 1988 and providing financing to production.Placer Development was an excellent company and spent over $8 million dollars on the Seabee over a 3 year period. Unfortunately for Claude Resources, Placer Development merged with Dorne Mines in 1987 and the new merged company, Placer Dome, established a minimum production threshold greater than the 50,000 oz per year which the Seabee appeared capable of supporting at that time. Placer Dome's request for an indefinite extension of the joint venture agreement to allow it to drill off a larger ore body was rejected by Claude Resources and the Seabee Property was returned to Claude in 1988."

Jan 1, 1998

By K. A. Lewandowski

Leach heaps are plagued with problems due to fine material migrating downwards, clogging the spaces between the coarser ore particles, resulting in decreased metal recovery rates. The use of a binder in agglomeration would allow the fine material to be immobilized, increasing the availability for the solution to come in contact with all the ore. As much as 1.64*1012 BTU per year would be able to be saved if a 25% increase in copper recovery was experienced, assuming that 70% of heap leaching units converted to using agglomeration technology. This is equivalent to approximately 18% of the energy currently being used in leaching heaps.

Jan 1, 2008

By Y. P. Chugh

This is the final report of a study done by IIT Research Institute for the Bureau of Mines to identify the problem areas and technological inadequacies in noncoal (metal, nonmetal, stone, and sand and gravel) mining and processing systems that are the primary causes of death, injury and occupational disease, and to make recommendations to improve safety and health in these operations. The findings and recommendations presented in the report are based on: (1) analyses of MESA injury and employment data for the period 1961-70, MESA fatality reports for underground noncoal mines (1968-72) and lost time accident data for 1970-72 obtained from mining and processing operation: (2) visits to a variety of noncoa1 mines and mills throughout the country to observe the operations and to study the safety organization and practices used in the industry and (3) interviews with industry and government representatives knowledgeable in the field of noncoa1 mining and processing safety and health. The report provides a comprehensive overview of safety and health problems.

Jan 1, 1974

By George J. Conroy

To provide data as a basis for proposed acceptance standards and procedures covering permanent splices in trailing cables, the Bureau of Mines conducted testing programs on the flexure life in flat types W and G dc trailing cable splices and ground conductors. Primary reliance was placed on laboratory testing, although some cross comparisons were made at manufacturers' plants and mine operations Besides providing data for acceptance standards and procedures, results of the program should promote the general improvement of commercially available splice kits.

Jan 1, 1977

By A T. Job, M L. Edgar, P R. McAree

Characterising ores in-pit and in real-time presents a significant value opportunity for the mining industry. Hyperspectral imaging systems are proposed as an enabling technology to achieve this real-time characterisation. This paper considers the application of a hyperspectral imaging spectrometer mounted on a shovel. We define the performance requirements for such a spectrometer and associated subsystems during a typical dig-load cycle. The relatively high swing rotation speed of the shovel requires approximately video-rate exposure times to achieve good spatial resolution. We analyse a selection of components against these requirements and find that suitable commercial spectrometers, detectors and optics appear fit-for-purpose. Automated, real-time spectral classification systems are also available, with only relatively modest requirements for processing power. The paper argues that at near peak solar illumination, a system for field deployment at the required sensitivity is viable using only commercial off-the-shelf components.CITATION:Job, A T, Edgar, M L and McAree, P R, 2017. Real-time shovel-mounted coal or ore sensing, in Proceedings Iron Ore 2017, pp 397–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017