Search Documents

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By M. C. Bétournay

Mine site infrastructure for storage and delivery of hydrogen must be standardized and acceptable for routine and safe industrial use before fuel cell technology is adopted as a major power source. An initial study reviewed possible options for production, storage and delivery of hydrogen for underground equipment. The high level review included assessment of economic, operational, technical, and health and safety risks. Following this review, a subsequent theoretical study to select typical minesite infrastructure and for construction at an operating research mine is outlined.

May 1, 2007

In recent years there have been significant advances in computing power and programming technology, enabling more complicated processes to be modelled in greater detail. This has led to increased understanding of these complex processes, including mineral processing circuits. JKSimMet was developed over the past 35 years, incorporating outcomes from various research projects conducted at the Julius Kruttschnitt Mineral Research Centre (JKMRC), part of the Sustainable Minerals Institute at The University of Queensland. It is a steady-state software program that allows the user to mass balance, model fit and simulate crushing, grinding and classification circuits. JKSimFloat has been developed over the past 20 years, incorporating outcomes from the JKMRC and other institutions around the world through the AMIRA International P9 project ? The Optimisation and Simulation of Mineral Processing Circuits. It is also a steady-state software program, similar to JKSimMet, but is focused on analysing flotation circuits. Both programs have been used in a wide variety of optimisation and design projects over many years. This paper provides an overview of both JKSimMet and JKSimFloat and examples of how both programs have been used to better understand, develop and optimise mineral processing circuits around the world.

Feb 27, 2013

By S. Assemi

Interaction forces between a hydrophilic silica particle and an air bubble were measured by atomic force microscopy using simplified model systems with deionized water and dilute KCl solutions. Contributions from the hydrodynamic force were minimized by using a low piezo speed. Particle-bubble separation distance and the bubble spring constant were calculated from linear regression of the piezo extension versus cantilever deflection. The bubble surface potential was then estimated from fitting the AFM-measured forces to the Hogg-Healy-Fuerstenau (HHF) model, using the surface element integration (SEI) method. Surface potentials obtained for the bubble at a low applied force were comparable with the literature data, suggesting that the simplified model used here can give a reasonable estimation of the bubble surface potential under moderate applied forces. Interaction forces between a silica particle and an air bubble were also measured at different locations on the air bubble surface. The force curves obtained at the edges of the bubble fitted very well to the theoretical force curves regardless of the applied force, while curves obtained at the center and halfway to the center, were more difficult to fit, in particular at higher applied forces (> 13 nN), suggesting that force curves obtained at the edges of the air bubble might be less prone to deformation effects.

Jan 1, 2008

By Cceliksirt, V Erkan

This computer program has been developed under the field conditions for use in control of surface drilling-blasting operations. This paper outlines the relevance of fragmentation to quarrying, open pit mining or road cutting and key features and operating principles of the software (DelPat for Windows 95).

Jan 1, 1998

By Atsushi Shibayama, Toyohisa Fujita, Wan-Tai Yen, Ke-jun Liu

"A gold has been leached with ammonium thiosulfate solution and several leaching conditions have been studied. The leached solution has been recovered by solvent extraction and the optimum conditions have been investigated.SUMMARYIn this investigation, a sponge gold sample (99.92% pure) has been leached with ammonium thiosulfate solution. The effects of CuSO4, (NH4)2S2O3, (NH4)2SO4, NH4OH and retention time on the gold leaching % (extraction %) and thiosulfate oxidation % (consumption %) have been studied. The copper ion acts as a catalyst in gold dissolution. On the other hand, it also accelerates oxidation of thiosulfate (consumption). It was found in this study that the best gold extraction condition was obtained at 43.2 ks with 0.8 – 1.0x103 mol/m3 (NH4)2S2O3, 30 mol/m3 CuSO4, 2.0 – 3.0x103 mol/m3 NH4OH, 0.4 – 0.5x103 mol/m3 (NH4)2SO4, pH 10±0.2 and 150 rpm. The thiosulfate oxidation was about 15% of the initial concentration."

Jan 1, 2003

By Dale Preece, Stephen Chung

Blasting induced rock fragmentation is an art that has been developed and refined for hundred’s of years through blasting and recording the results. Good blasting fragmentation practices were thus developed through experience. However, this method requires a history that is typically developed in a mine over a number of years and sometimes at considerable expense. Quantification of fragmentation as a function of rock-mass characteristics and blast design is attractive. Developments towards this end have included semi-empirical methods as well as computer codes that explicitly treat shock wave transmission and the subsequent rock breakage. This paper will present predictions of fragmentation resulting from rock blasting using the computer code AUTODYN and a new state-of-the-art material model for brittle rock and concrete.

Jan 1, 2003

By Rajive Ganguli

There are several elements of online pedagogy and information technology that are being used in the University of Alaska Fairbanks’(UAF) course “ES 201: Computer Techniques,” to enhance classroom teaching. The use of information technology in this class grew from a desire to make lecture notes available to students. This has grown to include a sophisticated, online delivery software package. It provides chat rooms, discussion groups, and online testing and grading. Online delivery aside, the class uses the telnet, e-mail and C++/FOR-TRAN compiler facilities of the university server during class to enhance learning. During class, for example, the students read the lecture notes on the Web browser, telnet to their university Unix accounts, check their e-mail and download programs (to be covered in class) sent by me, and then compile, run and modify the programs. The class, therefore, requires students to be active most of the time. This ensures their full attention and better learning due to the hands-on experience (Fig. 1).

Jan 1, 2000

By F. F. Skiba, P. J. Root

A mathematical model has been used to investigate crossflow effects in a stratified reservoir during an idealized displacement process. A process in which one incompressible fluid displaces completely another incompressible fluid of the same density and viscosity was considered. The reservoir was assumed to be composed of homogeneous layers which are discrete but interconnected. Approximate five-spot flow geometry was simulated by arranging two pie-shaped cylindrical (two-dimensional) wedges in series. Some of the common production methods rely, for their effectiveness, on the fact that the formation consists of isolated strata. This is particularly true of selective plugging and single-zone production-injection methods. The effectiveness of these techniques for several cases in which adjacent strata are in communication has been evaluated. The usual production-injection schemes for fluid injection processes involve using the same completion interval in both the production and the injection wells. The efficiency of this, as well as alternative productioz-injection procedures has been examined for some cases involving communicating strata. INTRODUCTION The performance of many fluid injection projects is marred by early breakthrough and by production of a high percentage of the displacing phase after breakthrough. This channeling effect, if it occurs in reservoirs which have large permeability variations, is often explained on the basis of a model composed of discrete, isolated strata. Corrective or preventive measures based on this same model are also common. The behavior of stratified models has been the subject of considerable study. An excellent review of the early literature was given by Seba.1 Studies of the depletion performance have since been made for continuous, unrestricted communication between strata2-4 and for production from one permeable bed in continuous but restricted communication with an adjacent permeable bed.5,6 Model studies of displacement processes in stratified systems with crossflow also have been reprted.7-12 Finally, methods which account for crossflow have been developed for computing displacement behavior in stratified systems.13,14 Most methods for controlling or preventing channeling involve some change in the interval open to production and/or injection. Although many variations of the selective completion problem have been studied in regard to the depletion of a reservoir, little attention has been given to the behavior of a displacement process under similar conditions. Sebal used a resistance network model to study the performance of a process in which one incompressible fluid displaces an identical fluid from a linear, stratified reservoir. He investigated the possibility of improving the vertical coverage by limiting the completion interval of the production well. This investigation deals with techniques in which selective completion of the production and/or the injection wells is used in an attempt to control channeling. At one extreme, selective plugging and single-zone isolation (assuming perfect execution) should be successful if the reservoir is actually made up of independent strata. At the other extreme, they can hardly be expected to be successful if the channeling is caused by a mechanism in which stratification effects are negligible even though there are extreme variations in the formation permeability and/or the injectivity profile of the wells is not uniform. By contrast, it is difficult to anticipate the effect that the amount of communication between the beds of a stratified system will have on the efficiency of selective completion techniques. The objective of this study is the quantitative determination of the effect of communication on the behavior of some particular stratified systems which will at least lead to qualitative conclusions.

Jan 1, 1966

Study on Mineral Processing for a Cassiterite Ore in Southwest China

Sep 13, 2010

By V Cullinan, D Buchanan

The Brunswick plant is located in Costerfield, approximately 40km east of Bendigo in central Victoria. Crushing, grinding, gravity gold concentration and flotation methods are used to produce a saleable gold concentrate and an antimony-gold flotation concentrate. This paper discusses the improvements made within the processing plant which have resulted in a 99% increase in throughput over nameplate capacity of 6 250 average tonnes per month to 12 445 average tonnes per month and increases of 12% gold (from 2007 average of 78% to 2014 average of 90%) and 16% antimony recovery (from 2007 average of 79% to 2015 average of 95%). This combined effort has resulted in an increase of equivalent gold ounces (AuEq oz) produced from 2010-2014 of 15 872 to 82 574 – a 66 702 increase.AuEq oz= Au oz +Sb t × Sb (US$/t)Au (US$/oz)CITATION:Buchanan, D and Cullinan, V, 2015. Improvements in bi-metal production at the Brunswick Plant, Costerfield, in Proceedings MetPlant 2015, pp 267–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Karen Mikkola, Gerald Luttrell, Jaisen Kohmuench, Glen Oswald, Michael Mankosa, Tracy Westerfield

Hydraulic separators are commonly used for particle size classification and gravity concentration of minerals and coal. Unfortunately, the efficiency of these processes can be quite low due to poor equipment design and variations in feed consistency. To help alleviate these problems, an industry-driven R&D program has been undertaken to develop a new generation of hydraulic separators that are more efficient and less costly to operate and maintain. Two of the most promising technologies, the CrossFlow and HydroFloat separators, have now been tested at industrial sites. The data obtained from these sites have been used to illustrate the potential performance improvements that can be realized through the application of these high-efficiency separators.

Jan 1, 2005

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940 to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the? Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940, to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942

By M. Rahmanpour

"Mine planning is a multidisciplinary procedure that aims to guarantee the profitability of a mining operation in changing and uncertain conditions. Mine plans are normally classified as long-term, intermediate-term, and short-term plans, and many factors affect the preciseness of these plans and cause deviations in reaching the objectives. Commodity price is the heart of mine planning, but it has a changing and uncertain nature. Therefore, the determination of mine plans in the presence of uncertain mineral price is a challenge. A robust mine plan reduces the risk of early mine closure. A procedure is presented to determine the value at risk (VaR) in any possible mine planning alternative. VaR is considered together with downside risk and upside potential in order to select the most profitable and least risky plan. The model is tested on a small iron ore deposit. IntroductionMining projects are normally evaluated with the objective of maximizing economic value, as measured by the net present value (NPV). The aim of mine planning is to develop a yearly extraction plan that guides the mining operation to the highest NPV (Dagdelen, 2007; Yarmuch and Ortiz, 2011). This plan considers the technical constraints such as blending requirements, block sequencing, and pit slope (Caccetta and Hill 2003). Thus, the mine plan affects the economics and the payback period of mining operations.Mine planning is a procedure based on which the profitability of the mining operation is guaranteed in changing and uncertain conditions (McCarter, 1992). However, conventional mine planning ignores the volatility and uncertainty of future commodity prices and does not allow for managerial flexibility. It is common practice to assume a deterministic and constant commodity price through the mine life. The problem with this approach is that the commodity price is the heart of the mine planning procedure and governs the profitability and feasibility of the operation; thus ignoring price volatility will result in a sub-optimal mine plan."

Jan 1, 2016

By John C. Machisak

THIS PUBLICATION presents injury experience and employment data for the nonmetal mining industry in the United States for 1960. Data for the mines and mills are presented separately, as shown in the list of tables. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry for their voluntary submission of injury and employment data. As the information submitted contributes largely to the promotion of safety in the industry, special effort has been made to ma e these questionnaires as complete as possible.

Jan 1, 1963

By Ike Isagon

Backfilling has become an integral process in underground mining operations, with varying cost-effective forms of application. This study is a part of an overall investigation into the backfill practices at Copper Cliff North Mine (CCNM). The mine is well-diversified in terms of backfill methodologies and practices. The mine employs different fill methods such as cemented and un-cemented rock fill, slag fill, and cemented hydraulic fill (or a combination of them) in order to fill the voids created by mining activities. The history of backfilling at CCNM has been dominated by cemented and un-cemented slag fill. Each fill method requires operating and engineering guidelines for a cost effective quality control system. The purpose of this paper is to briefly discuss the backfill methods and applications, operating guidelines, and engineering requirements at CCNM.

May 1, 2011

By Preston C. Holloway

Transformational roasting involves the heating of a material along with specific additives to induce mineralogical changes in the starting material. By controlling the chemical composition, roasting atmosphere, temperature and time of reaction, the mineral transformations induced during roasting can be engineered to control the distribution of valuable, or harmful, metals and to produce new mineral assemblages that are more amenable to conventional methods of metals recovery or to environmentally safe disposal. To date, this type of process has only been applied to the recovery of a limited number of metals, but current research is looking to expand the application of these techniques to the recovery of metals from a wider range of materials. An introduction to these techniques is presented along with preliminary results from their application to metals recovery from zinc bearing wastes, such as zinc ferrite leach residues and carbon steel electric arc furnace dust.

Jan 1, 2006

The interaction of flotation collectors with sulfide minerals takes place at the solid - solution interface. The electrochemistry of the processes which affect this interface are discussed. The interaction of xanthates with sulfides is an electrochemical process, xanthates being electro-oxidised to chemisorbed xanthate and dixanthogen. The role of oxygen is to provide a cathodic process to allow the anodic oxidation to occur. The hydrophobic condition of the mineral surface is brought about by the presence of the oxidised xanthate species. The action of reagents which can activate or depress the flotation of sulfides is discussed briefly.

Jan 1, 1971

By Alan A. Campoli

The mining industry has long been searching for an effective structural application that prevents weathering and falls of loose rock, debris, and sediment. J-Crete is a fiber-reinforced, engineered, cementitious composite rock application that is designed, tested, and successfully utilized as such a material. Laboratory evaluation of J-Crete material properties has shown the final compressive strength to be in excess of 7,300 psi (50.34 MPa), with 24 hour strength in excess of 1,500 psi (10.34 MPa). The flexural tensile strength is in excess of 600 psi (4.1 MPa) and is provided through a unique combination of polyvinyl alcohol (PVA) fibers activated by a proprietary liquid additive that prevents them from clumping and enables even distribution throughout the grout. Tensile bond strength in excess of 350 psi (2.4 MPa) at 28 day cure tightens the strata and holds loose material in place. Practically impervious to gas and liquids, J-Crete protects strata against long-term weathering, does not require screening to be effective, and has proven to be a successful waterproofing material. J-Crete has demonstrated the potential to alleviate coal mine roof cutters in soft, wet clay formations. J-Crete reinforces coal mine ribs by bonding directly to the rib, conforms to the strata, strengthens the rib, and eliminates sloughing due to long-term weathering; stabilizes coal mine entries by bonding directly to the brow and roof, and creates a monolithic shell with double reinforced corners.

Jan 1, 2012