Search Documents

By D. H. McCain

Through a unique partnership between the Colorado Mine Safety and Training Program (CMSTP), the Colorado Rock Products Association (CRPA) and the Higher Education and Advanced Technology (HEAT) Center, a video packed, dazzling CD-ROM training program was developed for new miners entering the aggregate industry. Why this product was developed, and why the aggregate industry, will be discussed along with the challenges faced throughout the project. Cooperation from every one involved including MSHA made this the product of which all other training materials in the mining industry will be measured against in the 21st Century. This product's versatility and wide application makes it a tool that is as critical to a mine's success as any earth moving machine. Developed with both state and federal grant moneys allows this product to be affordable to small operators and independent contractors. The quality of this two CD-ROM set rivals any commercially made CD-ROM training.

Jan 1, 2001

By Robert B. Johnson

The refraction seismic method has been used as an indirect means of exploring for fluorspar in southern Illinois by the Illinois State Geological Survey. Use of the method has been restricted to those areas where mineralization is associated with faults, a restriction necessitated by the operating principles of the refraction method. The seismic data enable the interpreter to locate fault zones in the subsurface and, under ideal circumstances, to make estimates of dip direction and magnitude and vertical displacement provided the local stratigraphic units are known and are geophysically recognizable. In this instance, refraction seismic exploration has been successful in the surface mapping of well-developed faults, both simple and complex with which fluorspar may or may not be associated. However, less clear results have been obtained where faulting has been less severe and where there are numerous accompanying mineralized joints.

Jan 1, 1964

By C Placzek, E Beattie, K Blake

Channel iron deposits (CID) consist of ferruginous chemical sediments, and are an unusual subset of Phanerozoic ooidal ironstone deposits almost unique to the Pilbara, where they constitute around 19 per cent of the Pilbara’s iron ore exports. These deposits occupy many of the ancestral river channels of the Pilbara region, especially the Robe River palaeochannels, incising and meandering through the Precambrian banded iron formations (BIF) of the Hamersley Group and the underlying Fortescue Volcanics.This paper explores the factors underlying geochemical variation in CID, particularly the chemical properties of goethite. The selected deposits in the western Robe palaeochannel and its tributaries show little or no secondary reworking by later water tables. There is a total absence of aluminosilicate clays with all the deleterious elements such as aluminium and silica. Instead, these are associated with the goethite mineral lattice, either within or adsorbed to the cortices of pelletoids.A thickly vegetated environment, and the presence of the Maddina Volcanics as potential source rocks for these western Robe CID is offered as an explanation for relatively high aluminium in the deposits studied, and, in turn, as the reason most parts of the palaeochannel are preserved as inverted topography.CITATION:Beattie, E, Placzek, C and Blake, K, 2017. Dirty goethite – a geochemical characterisation of some western Robe River channel iron deposits, in Proceedings Iron Ore 2017, pp 489–502 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By O. Kangal

Flame retardant materials can be incorporated or applied to products, including plastics and textiles, to increase their resistance to fire. Incorporating a flame retardant in combustible materials and plastics is a common procedure to reduce the risk of fires. Flame retardant applications include interior and exterior woods, structural steel columns, fabrics, open and closed cell foam, pressure treated wood, Formica and all types of fabrics for use in commercial applications as well as residential applications where their fire protection products can save lives and valuables. Huntite and hydromagnesite are amongst the most important flame retardant additives materials. Although various areas of the world have potential huntite and hydromagnesite deposits, their place in industry is not well known, and a detailed field search for their deposits has not yet been conducted. They are active during the starting phase of a fire, in that they prevent the spread of an inner or exterior source of ignition to the flame-retarded material, thereby, preventing, delaying or inhibiting the spread of a fire. Flame-retardants are, therefore, just one element among many in a concept for preventive fire safety. To obtain huntite and hydromagnesite concentrates that are more than 95% pure, which are used in flame retardant industry, flotation tests were conducted on low-quality huntite and hydromagnesite ores.

Jan 1, 2009

By Mech B

This paper gives a general description of mining practice at The Zinc Corporation Ltd., Broken Hill, New South Wales.The basic mining methods are those which have been common in Broken Hill for many years and have been well described in previous Proceedings. The main object of this paper is to indicate developments which have occurred in recent years and to describe changes in layout, mining methods and equipment which are taking place at present.The following headings have been adopted: History Geology and general characteristics of the orebodies, Geology, The lead lode, The zinc lode, General characteristics, Ore reserves, General mining method, Exploration and diamond drilling, Shafts and shaft sinking, Main shaft, Old main shaft, Block 5 shaft, New upcast airway, Development, Level interval, Level layout, Driving and crosscutting, Winzing, Rising, and Stope preparation.

Jan 1, 1946

A symposium was held on January 30 and 31, 1973, at Pittsburgh, Pa., to review the state-of-the-art in designing and utilizing diesel-powered equipment in underground mining. The Health and Safety Activity of the Bureau of Mines sponsored the symposium with major assistance from the following four participating organizations: The American Mining Congress J. Allen Overton, President The United Mine Workers of America Arnold R. Miller, President The National Independent Coal Operator's Association Cloyd D. McDowell, President The Bituminous Coal Operators' Association, Inc. Guy Farmer, President Seventeen papers were presented during four half-day sessions devoted to the general subjects of the diesel engine, the place of the diesel in underground mining, health protection using diesels underground, and maintaining safety of diesels underground. Eleven of the speakers were from industrial organizations here and abroad; one represented the Provincial Government of Nova Scotia; two were with the Department of Health, Education, and Welfare; and three reported on Bureau of Mines work related to diesels.

Jan 1, 1975

By Jay F. Colinet

Researchers at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) work to reduce respirable dust exposures in mining operations. One focus of this research is silica dust control for surface and underground operations in the metal/nonmetal mining industry. PRL researchers analyze dust sampling results from the Mine Safety and Health Administration (MSHA) to identify high-risk occupations to guide research efforts. Research is then conducted in an effort to improve existing technologies and/or develop new controls for reducing worker exposure to airborne silica dust. During the last few years, PRL researchers have conducted research related to the following goals: improving protection provided by enclosed cabs on mobile surface mining equipment, reducing dust generation from surface drills, reducing dust levels in iron ore operations, and developing a new method to clean dust from workers? soiled clothes. A description of each of these controls and subsequent dust reductions quantified through site surveys will be provided.

May 1, 2007

By G. C. Lammers

The object of this study was to determine the economic feasibility of hydraulically transporting Sandow (Tex.) lignite 100 miles and dewatering and thermally drying the transported lignite to a surface-dry condition. The most important factors involved in the feasibility of hydraulic transport, are the degradation incurred during transit, the length of the line, and the cost of alternative methods of shipment. In pipeline tests in which roughly 75 miles of hydraulic transport was simulated the percentage of minus-325-mesh solids increased from about 1 to 41 percent for both lignite and bituminous coal; in the micron sizes the coal fared considerably better than the lignite. Such degradation, even though it enhances flow through the pipe-line, severely aggravates the dewatering problem on lignite. Cost studies indicated that continuous vacuum filters offer the most economical means of dewatering minus-1/8-inch material. Surface moisture, if high, must be removed by relatively expensive thermal drying.

Jan 1, 1958

Two structurally and mineralogically distinct sulphiderich veins cross-cutting the disseminated sulphides of the Nairne Pyrite Member appear to be products of local remobilization of sulphides under fracture-induced free energy gradients during regional metamorphism and tectonic deformation.The contrasting mineralogy of the two vein types may have arisen as a result of differences in the structural orientation of the veins and!or the relative ages of the veins.

Jan 1, 1969

By Y. M. Chen, H. L. Zhang, W. U. Bing, C. Q. Zhou

Multiphase flow in the widely used Vanyukov furnace was numerically studied. An unsteady three-dimensional and three-phase flow model was firstly built using the computational fluid dynamics (CFD) software ANSYS FLUENT®, and then solved with the volume of fluid (VOF) and k - ??model. The results showed that the proposed model could be used to predict the multiphase movement, the slag/air fluctuation, the vortex formation, and effects of structural and operational parameters. By fast Fourier transform (FFT), the dominant frequency of density with time signal was calculated as 0.29 Hz. The analysis of different injection flow rates of enriched air indicated that this variable has a major effect on the mean slag velocity. The peak mean velocity increased from 2.17 to 4.99 m/s while the flow rate of enriched air varied from 70 to 160 m/s. The proposed model provides a method to optimize the furnace structure and operating conditions for the best furnace performance and lowest energy consumption.

Jan 1, 2015

Pulverized Fuel Combustion The apparatus shown in the illustration is a complete equipment f r supplying coal to boiler and metallurgical furnaces, cement and lime kilns, dryers, and to all furnaces requiring a temperature and quality of fame under prompt and easy control. It is claimed that the Aero Pulverizer makes practicable the highest efficiency obtainable from burning coal. It makes coal burn like a gas, a flame, the physical and chemical character of which is regulable- a flame that may be elongated or shortened, thus placing the zone of highest temperature where needed- a flame that may be made oxidizing, reducing, or neutral, as occasion may require. The coal is burned as pulverized, and there is no storage of the powder with its attendant hazard. Artificial drying before pulverizing is not necessary if the coal supply be sheltered from rain and snow. Where the Aero is used, it is wholly a furnace question whether a dryer should be installed; it is not at all a pulverizing or storage question. Labor is reduced to a minimum. Slack coal at low cost yields its last B.T.U.

Jan 11, 1915

By Niels Kofoed

Upon completion of the 6,200 m (20,340 lineal ft; lft) North Tunnel drive for the Portland East Side Combined Sewer Overflow (CSO) Tunnel project in Portland, OR, the slurry tunnel boring machine (TBM) had to be returned from the Port Center shaft at Swan Island to the Opera shaft at the main mining site for the 2,700 m (8,860 lft) South Tunnel drive. At the Port Center shaft, the main 513-t (565-st) TBM and TBM tailshield were hoisted out of the shaft in two pieces using four 200-t (220-st) strand jacks mounted on a 635-t (700-st) hydraulic boom gantry system supported by Emmert International?s custom gantry tracks designed to span the shaft. After lifting the TBM components out of the shaft, the gantry system loaded the TBM components onto two Goldhofer platform trailers, which then transported the TBM and tailshield to a barge using a roll-on/roll-off method.

Jan 1, 2011

By E. C. Stephens

The eastern Washington— Idaho clay region stretches along the northeast margin of the Columbia basin for 150 mil es. The three better known and developed clay areas are Clayton, Wash., (2 miles north of Spokane); Mica, Wash., (10 miles southeast of Spokane); and Moscow-Deary-Bovill, Latah County, Idaho (about 80 to 90 miles southeast of Spokane) see Fig. 1. Clays from the eastern Washington— Idaho clay area have been mined for more than 50 years. At present Mica, Washington deposits are used by the Gladding—McBean & Co. to make a variety of bricks and ceramic products and Latah County, Idaho clays are used by the A. P. Green Fire Brick Co. to make refractories. The Anaconda Co. made an intensive investigation of the clay deposits in the northeastern Washington-!daho area in 1919 to determine the existence of a supply of raw materials from which alumina could be made. The greater part of the work, which included systematic drilling and shaft sinking, was concentrated at Mica, Wash. This was part of a research project carrted on by the Anaconda Metallurgical Research Dept. under the direction of Frederick Laist and F. Frick and it was terminated in 4920. V. D. Perry, Vice President and Chief Geologist for The Anaconda Co., in 1952 assigned the writer to make a preliminary study of clay and other potential sources of alumina ore in the Pacific Northwest with particular emphasis on those deposits which might be of future importance to The Anaconda Co9s. then new aluminurri plant at Columbia Falls, Mont.

Jan 1, 1961

By J. Shang, P. Howarth, B. Morris

Tailings from the nickel refinery in Copper Cliff, Ontario, consist of fine silicates mixed with a variable amount of conductive and magnetic minerals mainly associated with sulphides and iron oxides. Subsequent oxidation of sulphide- rich phases within the tailings results in the formation of an acidic leachate that may contain significant concentrations of trace metals. Mapping the spatial distribution of regions of higher sulphide concentration therefore provides insight into the distribution of the acidgenerating potential within the tailings. Electrical conductivity is constrained by two parameters — the concentration of metallic sulphides and the ionic concentration of acid in groundwater. Magnetic susceptibility is directly related to the pyrrhotite and magnetite content. It is proposed that combining information derived from airborne electromagnetic and magnetic surveys can provide an indication of metallic sulphide distribution. Preliminary investigations of airborne electromagnetic and magnetic data acquired concurrently over the sulphide-rich Copper Cliff tailings site reveal that these parameters can provide information on mine tailing extent and permit separation of tailings with varying compositional and alteration levels. Airborne geophysical data provide information about the subsurface while a digital elevation model (DEM) and hyperspectral imagery record surface conditions. Integration of the two data sets can reduce ambiguity when interpreting mine tailing distributions and their subsequent alterations.

Jan 1, 2001

By M. L. Bakker

The ISASMELT? top submerged lance (TSL) bath smelting process was developed in Mount Isa, Australia by Mount Isa Mines Limited (now a subsidiary of Xstrata plc) during the 1980s. By the end of 2011, the total installed capacity of the ISASMELT? technology will exceed 8 000 000 metric tons per year of feed materials in copper and lead smelters around the world. Commercial plants, operating in Belgium and Germany, are also batch converting copper materials in ISASMELT? furnaces. This TSL technology is equally effective for continuous converting processes, in which role it is called ISACONVERT?. This paper presents the recently patented ISACONVERT? process for the continuous converting of nickel and platinum group metal (PGM) containing mattes using the calcium ferrite slag system. The paper focuses on the potential application of the ISACONVERT? technology to existing nickel and PGM smelting complexes.

Jan 1, 2011

By D. Dodgen, L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million tom of ash, boiler slag and FGD (flue gas desulfurization - "scrubber") materials as by-products. Utilities and others who bum coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Feb 24, 1997

By W. P. Yant

A previous report of the Bureau of Mines dealt with the toxicity of dichlorodifluoromethane5, a new refrigerant that has a remarkably low toxicity. Continued research by the Prigidaire Corporation6 and toxicological experiments performed in the Laboratory of Applied Physiology of the University of Cincinnati7 revealed another organic fluoride, dichlorotetrafluoroethane, whose toxicity also appeared to be of a very low order and whose physical-and chemical properties make it suitable for refrigeration purposes. In addition to low toxicity, safety in its use is further enhanced by its physical properties, which permit the design of equipment that operates at comparatively low pressures and hence mitigates the dangers and problems of leakage. The investigation described in this report was performed by the Bureau of Mines at the request and with the cooperation of the Frigidaire Corporation.

Jan 1, 1932

By A. G. Yapo, T. W. Camm

"All-in sustaining cost is a metric used by mining companies to reflect the cost of gold mining in a consistent format useful to both investors and mining professionals. Cost reporting focused on the direct cost of mining and processing ore was summarized in the non-GAAP cash cost developed by the Gold Institute in 1996. In 2013, a group of mining companies, working with the World Gold Council, developed a more inclusive approach to reporting costs designed to solve the dilemma of showing a more comprehensive reflection of recurring costs involved in producing gold, without discouraging investors. INTRODUCTION Mining today plays a key role in the development of our civilization as a source of essential raw material and provider of essential fuels, producer of jobs, and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer today than before as companies understand better their work environment and the importance of mining responsibly. A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production. An attempt to bring light and clarity on the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the All-in Sustaining Cost (AISC) and All-in Cost (AIC). Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses, and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact the high gross margin (sales minus cash costs) has been promoted the past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $1900 per ounce in August 2011, gold producers were not reporting excessive profits in their cash flow / income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits."

Jan 1, 2017

By Y. L. Sun

The feasibility of using the ultrasonic wave attenuation method for measuring in-situ stress is examined theoretically and experimentally. The theoretical analyses show that for a given rock type the relation between stress and attenuation coefficient ratio can be approximated closely by second-order polynomials. Combining the elastic and statistical theories, the magnitude and direction of the existing principal stresses can be predicted by using the relations between stress and attenuation coefficient ratio obtained in the calibration of core specimens. Several experiments are conducted in the laboratory on two types of rock. The experimental study consists of two parts: the attenuation-coefficient measurements in core specimens under uniaxial stress and the attenuation coefficient measurements in boreholes drilled through blocks of sandstone and limestone subjected to uniaxial compressional stress. Compressional waves are used exclusively in the measurements.

Jan 1, 1989

By T. Ruben

Micropiles have been used for the last forty years to strengthen building foundations. This article gives information about the technology and capacity of micropiles.

Jan 1, 2000