Search Documents

By Naresh Koirala

The Greater Vancouver Regional District completed installation of a 2.5 Km long, 2400 mm diameter concrete sewer in Delta, British Columbia in 2000. The sewer traverses through area of peat and soft ground. The ground investigation along the sewer alignment consisted of cone penetration tests and auger drilling with standard penetration tests. The gravity sewer is supported on precast, pretensioned spun concrete piles imported from Malaysia which had never been used for a major project in North America. The capacities of the installed piles were tested using pile driving analyzer (PDA) and three static load tests. A total of 46 PDA tests were carried out during pile installation. The paper describes the pile vetting process the owner went through prior to accepting the piles for use in the project and performance of the piles. It compares the pile capacity estimated from the PDA tests with that estimated from soil mechanics methods using data from cone penetration tests and standard penetration tests. The ranges of estimated capacities calculated by different methods are discussed from design capacity selection considerations.

Jan 1, 2004

By P. A. Witt

"Highland Valley Copper is a conventional truck-shovel mining and flotation concentrator operation located 75 km southwest of Kamloops, British Columbia (Fig. 1).The ore is situated within a porphyry copper deposit and is mined at a rate of 135,000 mt/day from two separate open pits. The nearby mill produces concentrates containing 375 million pounds of copper and 5 million pounds of molybdenum metal yearly. In the Valley pit, head grades are roughly 0.40% Cu at a 0.23% Cu equivalent cut-off. The Valley pit strip ratio currently sits at 0.55:1 with waste quantities made up of separate rock and unconsolidated overburden units. From the mill, concentrates are trucked to nearby Ashcroft and then hauled by rail to ocean port facilities in Vancouver. The mine employs 950 people and is planned to operate until 2009. The operation is a partnership between Teck Cominco (63.9%), BHP Billiton (33.6%), and others (2.5%). Management is shared by the two principal owners and directed by a management committee."

Jan 1, 2005

By Shimi Tzobery, Jay Davenport, Raymond Henn, Sam Bandimere

Over the past several decades, the use of cement-based grouts using ultra fine cement as a replacement for portland cement has begun to gain acceptance as an alternative to chemical solution grouts used in permeation grouting. The amount of information currently available on grouts made with ultrafine cement is limited. The authors used a previously developed field testing program to perform additional tests to evaluate the permeation performance of portland and ultrafine cement-based grouts. For the first time, the 2003 testing program included an attempt to determine the 28 day compressive strength of the sand permeated by the grout.

Jan 1, 2005

By J. Pascoe, J. H. van Laar, J. H. Marais, F. J. L. Matthee

Advanced measurement and verification (M&V) is a process where the impact of an energy initiative is determined in real time. Data prediction models can be used to predict and compare energy consumption with a predetermined baseline. Deeplevel mines can benefit from advanced M&V as the impact of operational changes can be identified in real time. Ultimately, this can ensure that informed decisions are made regarding energy management based on the impact and severity of the occurrence. Previous studies on advanced M&V do not account for operational changes to the model’s baseline. These changes can significantly impact the performance of both the mine and related activities. The aim of this study is to propose a method that can accurately predict the energy consumption of a deep-level mine regardless of operational changes. To achieve this objective, nine different data predictive modelling techniques were considered. The proposed method is based on the Moving Average (MA) modelling technique due to its simplicity, flexibility, and rapid development time. The coefficient of variation for the root mean square error (CV(RMSE)) was used to statistically analyse the modelling error. If the predictions exhibit an unsatisfactory CV(RMSE), the model dynamically adjusts to reduce the prediction error. The model was developed to adapt to operational changes in scenarios where the standard model becomes irrelevant. The method developed in this study was able to predict the future energy consumption of deep-level mines with an accuracy of 99%, improving the mine’s energy and finance management.

Dec 13, 2023

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental sampling error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centred on the sampling constant K and the exponent, alpha (a) of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis method and the heterogeneity test method purport to provide such constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine, and Lily mine. Two of these mines (Mponeng and Kloof) are typical Witwatersrand-type gold mines, and the third is an Archaean-type shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appear to be too small and do not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2010

By V. Bondarenko

The forecasting of floating earth inrush into the working is to a great extent connected with the investigation of the rock mass stressed-deformed state around the working. The aim of such investigations is to estimate the carrier ability of the protective layer (which is stabilized by the physico-chemical mode of fixing) and to determine it's thickness, which is to be sufficient to present the floating earth inrush into the working. We consider the protective layer to have exhausted it's carrier ability if the rocks of this layer reached the overlimit phase of deformation and it's greater part (section), which adjoins the working. is destroyed up to the limit of the remaining strength. So, the aim of investigations is to determine the size of the rocks inelastic deformation zone in the roof of the working. It is necessary to take into account the presence of water saturated seam in the roof and the overlimit characteristics of the rocks, their ability to lower the carrier capacity up to the level of the remaining strength.

Jan 1, 1996

By T. P. Williams, M. B. Rydzewski, B. Corner

Konkola Copper Mines (KCM) plc is an integrated copper producer operating on the Copperbelt in Zambia. KCM has numerous mining operations located in the towns of Chililabombwe (Konkola Mine), Chingola (Nchanga Open Pit and Underground operations), Lusaka (Nampundwe Mine), with a smelter located in Kitwe (Nkana Smelter) and an SX-EW plant in Chingola (Nchanga Tailings Leach Plant). [ ]

Jan 1, 2005

The aim of this investigation was to study the influence that varying production rates have on iron sinter quality. This was done by performing sinter pot tests at different pressure drops over the sinter bed, namely 11 kPa and 15 kPa (for 500 mm total bed depths). During each of the sintering processes temperature-time profiles were recorded of the top, middle and bottom layers of the sinter bed. On completion of the sinter process the sinter cakes were divided into top, middle and bottom layers. The physical properties of each layer were subsequently characterized by performing a tumbler test and a sieve analysis. A comprehensive mineralogical study was also conducted on each layer. This study revealed that sinters of similar cold strength could be produced under the examined production rates. However, a higher production rate was accompanied by an increased amount of fines. The cold strengths of both sinters significantly increased from the top layer to the bottom layer of the sinter bed. This strength variation is not related in any simple way to the phase composition. Keywords: Sinter, sinter bed, production rate, phase composition, cold strength, tumbler index, sieve analysis, temperature-time profile

Jan 1, 2003

By L. Westerstrom

Supply and Demand After a dismal first half, the industry saw a marked improvement in its markets during the final six months of 1983. Domestic consumption was 17.6% higher in the second half of the year, primarily due to a surge in electric power requirements. The sharp increase in demand for electric power during the third and fourth quarters afforded utilities the opportunity to lower stocks that had accumulated to record levels during 1982. Consumer stocks were reduced from 179 Mt (197 million st) at the end of June to 153 Mt (169 million st) by the end of the year. That is the largest inventory drawdown on record during a six-month period without a major coal strike. Despite the huge depletion in inventories, coal production in the second half of 1983 rose 1.3% above output in the second half of 1982. However, because of the disappointing first half, production in 1983 totaled only 712 Mt (785 million st), 6.4% less than the 760 Mt (838 million st) produced in 1982. Demand The extent to which the economic recovery affected coal markets in 1983 varied: • total domestic coal consumption increased 4.2%; • electric utility coal consumption increased 5.3%; • exports declined by about one-fourth; • coal consumption at coke plants declined 9.5%; and • coal consumption in the other industrial sectors increased 2.9%. Domestic coal consumption totaled 667 Mt (737 million st) it 1983, 27 Mt (30 million st) more than 1982. Electric utility consumption increased from 539 M1 (594 million st) in 1982 to 567 M1 (625 million st) in 1983. Coal consumption at coke plants declined from 37 Mt (41 million st) to 34 M1 (37 million st). Residential and commercial use increased 181 kt (200,000 st) - from 7.4 to 7.6 Mt (8.2 to 8.4 million st). Electric Utilities: Electric power generation increased 3.1% in 1983. Demand for electric power increased in all major consumer categories. Residential and commercial use rose 2.7% and 3.3%, respectively. The most striking increase, however, and indicative of the economy's strong upturn, was the increase in industrial electric power use. Industrial power requirements, which declined 9.8% in 1982, rose 4.1% in 1983. The electric utility sector continued to expand its use of coal last year while lowering its requirements of oil and natural gas. In 1983, electric generation from coal increased 5.7%, while genera-

Jan 5, 1984

By David Hake, David Salisbury

The Drainage Services Department (DSD) of the Hong Kong SAR Government commissioned the design and construction of the West Kowloon Drainage Improvement, Stage 2, Phase 2, Kai Tak Transfer Scheme (KTTS) project in 2000 to relieve potential flooding in Mong Kok caused by the insufficient capacity of the existing storm water drainage system. The KTTS involves construction of a 1.5km,4.4m drainage tunnel and a 450m long box culvert, running from Waterloo Road near Hereford Road to the existing Kai Tak Nullah in San Po Kong. This paper describes the design and construction of; the bored tunnel through both hard rock and soft ground using a slurry Tunnel Boring Machine (TBM), six associated access shafts, a connection structure at Waterloo Road and the box culvert connecting the bored tunnel to the outfall at Kai Tak nullah. Details will be provided on the contractor’s alternative designs adopted during the contract including the use of fibre reinforced shotcrete as one-pass temporary and permanent support for three of the shafts and modifications to the Engineer’s design for the box culvert structure.

Jan 1, 2005

The presence of undetonated explosives in a rock face after firing constitutes a hazard which can result in a fatal or serious accident if undetected before drilling commences.Most accidents caused by drilling into explosives are the result of failure to examine the working face properly and lack of care in subsequent drilling operations; it is not always realized that explosive may be left in the butts of holes or may be driven into cracks or crevices in the rock.Obviously the best means of preventing accidents of this nature is to adopt methods of drilling, charging and firing which will reduce the hazard to a minimum.There are three ways in which undetonated explosives may be left in the rock face, namely:1. Misfires.2. Cut-off shots.3. Incomplete detonation or failure of the charge to propagate throughout.MisfiresNo attempt will be made in this paper to deal fully with the question of the prevention of misfires, as apart from the fact that most of the preventive methods are well known, it is believed that if the miner receives his explosives and means of initiation in good order, and proper care is taken in their use, the failure of a charge to fire will be a rare occurrence. The provision of central fuse capping stations on mines has gone a long way towards the elimination of misfires caused by the mishandling of safety fuse anddetonators.

Jan 1, 1956

By J W. Hedenquist

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Epithermal deposits (Au or Ag dominant, ± base metals) form within ~1 km of the surface in volcanic belts, both arcs and rifts, with the different tectonic settings reflected in distinctly different characteristics. Within arcs, deposits are typically intrusion centred and commonly associated with hypogene advanced argillic alteration, both in lithocaps and as halos to shallow or proximal portions of some veins; such alteration is coupled with processes that form porphyry Cu-Au deposits at depths of ~1–3 km. Introduction of metals is related to the subsequent phyllic-stage overprint; if this fluid rises to the level of the lithocap or into epithermal veins, Au mineralisation with Cu or Ag may occur, associated with sulfate minerals or muscovite. By contrast, Au-rich (both low Ag:Au ratio and bonanza grade) colloform quartz veins form at shallow depths in volcanic rifts, typically within a few hundred metres of the surface, with clay halos and topped by silica sinter if the palaeosurface is preserved. The geologic variability in volcanic belts, including host rocks, structures and hydraulic gradients, means that many epithermal deposits vary from the end-member features of the principal styles. Effective exploration requires familiarity with end-member styles as well as potential variations, plus the mineralogical indicators of palaeotemperature (eg evidence for erosion depth, fluid flow channels). This knowledge helps the geologist in the field to imagine what might be buried and where, and how to best test the target with drilling.CITATION:Hedenquist, J W, 2015. Recent developments in understanding of and exploration for epithermal deposits in volcanic arcs , in Proceedings PACRIM 2015 Congress, pp 11–16 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Economically significant gold-silver mineralization occurs in Miocene andesitic flows and tuffs at Golden Cross, eight kilometres northwest of Waihi, New Zealand. The highest grade mineralization occurs in a steeply dipping elongate zone of strong quartz veining and brecciation underlying, but contiguous with, a gently dipping tabular quartz vein stockwork containing potentially open-pittable lower grade gold-silver mineralisation. The stockwork zone is enveloped by argillic alteration and overlain by unaltered Pliocene andesites and recent tephra. Evaluation of the prospect involved underground and surface geologic mapping, rock and soil geochemistry, IP-resistivity, magnetic and gravity surveys as well as 1844 metres of reverse circulation drilling and over 30 000 metres of core drilling. The paper outlines the exploration history of the area and describes the results of the various exploration techniques used at Golden Cross.

Jan 1, 1986

By Leo F. Reinartz

It was with humility that I accepted the invitation of the Board of Directors of our Institute to deliver the Twentieth Howe Memorial Lecture. Many previous lecturers could speak from personal experience of the great work done by Professor Howe. It was not my privilege to be one of his students but, indirectly, I came under the influence of his work many years ago. My mentor in Metallurgy at Carnegie Institute of Technology, Prof. Fred Crab tree, was an ardent admirer of Professor Howe and his work. Professor Crabtree taught me early to appreciate Professor Howe's love of truth and keen desire to find a scientific reason for every metallurgical phenomenon. In this early search, Professor Howe encountered many unexplainable facts. Nevertheless, in the classic text, "The Metallurgy of Steel," published in 1891, he indicated that he believed Research could light the way. Under the heading of "The Treachery of Steel" he said: "In the early use of Bessemer and Open Hearth Steel, many then unexplained and hence mysterious failures occurred. With our present knowledge, an easy explanation of most of them would probably have been seen. But even today certain unexplained and apparently inexpli- cable failures occur in steel; inexplicable in spite of full and intelligent investigation." Then Professor Howe continued to talk about "the trustworthiness of steel" in the following manner: First, the steel-maker has learned by experience. He knows today far better the effects of a high percentage of carbon or of phosphorus; of cracks, pipes and blow-holes; of segregation and imperfect mixing; of over-heating; of finishing too hot or too cold. Knowing, he guards against them more effectually, and keeps at home much steel that he would formerly have sent into the market. Those who would not, or could not learn and do, have been driven out of the business; the conditions necessary for producing good sound steel by the acid Bessemer and the acid Open Hearth processes have been mastered. By and by, the basic process came along with new conditions, new liabilities to unsoundness, a great hue and cry about mysterious fractures followed, and Lloyd's register provisionally forbade the use of basic steel. Much basic steel was irregular and brittle throughout; too much carbon, too much phosphorus, too cold teemings—imperfect mixing. Still there was little doubt that, with further experience, these difficulties of the basic process would be mastered as those of the acid process had been. This shows that Professor Howe could not take anything for granted. Believing that careful research would find the answer to all mysterious phenomena, he was several generations ahead of the practical acceptance and adoption of this principle.

Jan 1, 1943

By Leo F. Reinartz

It was with humility that I accepted the invitation of the Board of Directors of our Institute to deliver the Twentieth Howe Memorial Lecture. Many previous lecturers could speak from personal experience of the great work done by Professor Howe. It was not my privilege to be one of his students but, indirectly, I came under the influence of his work many years ago. My mentor in Metallurgy at Carnegie Institute of Technology, Prof. Fred Crab tree, was an ardent admirer of Professor Howe and his work. Professor Crabtree taught me early to appreciate Professor Howe's love of truth and keen desire to find a scientific reason for every metallurgical phenomenon. In this early search, Professor Howe encountered many unexplainable facts. Nevertheless, in the classic text, "The Metallurgy of Steel," published in 1891, he indicated that he believed Research could light the way. Under the heading of "The Treachery of Steel" he said: "In the early use of Bessemer and Open Hearth Steel, many then unexplained and hence mysterious failures occurred. With our present knowledge, an easy explanation of most of them would probably have been seen. But even today certain unexplained and apparently inexpli- cable failures occur in steel; inexplicable in spite of full and intelligent investigation." Then Professor Howe continued to talk about "the trustworthiness of steel" in the following manner: First, the steel-maker has learned by experience. He knows today far better the effects of a high percentage of carbon or of phosphorus; of cracks, pipes and blow-holes; of segregation and imperfect mixing; of over-heating; of finishing too hot or too cold. Knowing, he guards against them more effectually, and keeps at home much steel that he would formerly have sent into the market. Those who would not, or could not learn and do, have been driven out of the business; the conditions necessary for producing good sound steel by the acid Bessemer and the acid Open Hearth processes have been mastered. By and by, the basic process came along with new conditions, new liabilities to unsoundness, a great hue and cry about mysterious fractures followed, and Lloyd's register provisionally forbade the use of basic steel. Much basic steel was irregular and brittle throughout; too much carbon, too much phosphorus, too cold teemings—imperfect mixing. Still there was little doubt that, with further experience, these difficulties of the basic process would be mastered as those of the acid process had been. This shows that Professor Howe could not take anything for granted. Believing that careful research would find the answer to all mysterious phenomena, he was several generations ahead of the practical acceptance and adoption of this principle.

Jan 1, 1943

Holla has given a good background to the various methods of subsidence control in the coalfields around Sydney.The present writer notes that in many cases, especially with wide longwall panels, there is not the flexibility to alter the mine layout as there is to some degree with the various pillar extraction methods. For this reason it may not be possible to plan the workings to minimise subsidence and some damage to structures may occur. The cost of repair or the cost of subsidence provisions to minimise damage may be small in relation to the tonnages of coal which would otherwise have to be sterilised. One method of subsidence control which has been in use in the Newcastle area since 1970 is the panel and pillar layout (partial extraction layouts with stable pillars). An extracted panel width of 0.6 times the depth of cover resulted in a maximum subsidence of 115 mm for an extracted seam thickness of 2.2 m.As Holla points out, the extracted panel widths in relation to th depth of cover depend on the particular geological setting. His Fig. 3 shows that the subsidence over a panel width of 0.3 times the cover depth in the Southern Coalfield is the same as over a panel width of 0.55 to 0.6 times the cover depth in the Northern Coalfield.Selective pillar extraction and longwall mining can both be used in the panel and pillar layout. Holla's Figs 2 and 3 are used to estimate the maximum subsidence over an extracted panel of known geometry. Maximum subsidence is related to seam thickness. What provision is made for a reduction in subsidence due to the coal which remains behind in a pillar extraction panel if the pillar recovery is poor? The writer suggests that an effective seam height could be used, based on the actual mining height reduced by a factor to account for the percentage recovery of coal from an extracted panel.

Jan 1, 1986

Despite the current economic downturn that is now decimating iron ore production, Minnesota?s mining operators remain optimistic about the long-term prospects for the industry. Reflecting this optimism, the development of several new mining projects continues in the state. The future of mining in Minnesota was the featured topic at the combined 82nd Annual Minnesota Section of SME Meeting and 70th Annual University of Minnesota Mining Symposium. More than 500 mining industry professionals, including engineers, executives, mining managers and equipment suppliers from the around the world, attended the meeting, which was held April 14 and 15, 2009, in Duluth, MN. The combined meeting featured a keynote session with three distinguished speakers plus a panel discussion by representatives from several of Minnesota?s taconite producers. The keynote speakers were Curtis Clark, president and chief operating officer, Behr Dolbear, who gave a presentation on the ?State of the Mining Industry.? Phil Newman, chief operating officer, CRU Strategies, spoke about challenges facing the mining industry and James A. Skurla, acting director, Bureau of Business and Economic Research, Labovitz School of Business and Economics, University of Minnesota Duluth, discussed the importance of mining to northeastern Minnesota?s economy. The taconite producers panel discussion included Jonathan Holmes, vice president and operations manager, ArcelorMittal; Ed Latendresse, vice president and general manger, Hibbing Taconite; John Tuomi, vice president operations services, United Taconite and Mike Mliner, vice president and general manager, Northshore Mining. The mangers provided updates on their respective operation The meeting included concurrent technical papers sessions on mining, processing, environmental and nonferrous mining. The sessions included technical papers that provided information on the status of a number of new mining projects in the state. The conference also offered a SME short course titled ?The basics of iron mining.? A tradeshow that featured about 100 companies and organizations offering products and services to Minnesota?s mining industry ran in conjunction to the conference. It was estimated that more than 900 people, including conference registrants and special invited guests of the vendors, attended the tradeshow opening reception. This was the largest trade show in many years. The Minnesota Section of SME also held its annual business meeting during the conference.

Jan 1, 2009

By Jean Habimana

Complex and distinct geological units spread along the 7-mile long 30-ft inside diameter Upper Rouge Tunnel CSO Control Project in Detroit, Michigan. Its construction is divided in two tunnel construction packages: The South Tunnel, to be driven in finely laminated weak TG Limy Shale, will be excavated by a shielded TBM with precast concrete segmental lining, while the North tunnel, predominantly in a relatively more competent geologic formation Antrim Shale, will be excavated by a main beam TBM with a two-pass lining system. The adits and deaeration chambers will be excavated by sequential excavation method. This paper addresses the process of selecting excavation methods and lining systems for shafts, tunnels, connecting adits, and deaeration chambers.

By R B. Turner

The authors have studied and analysed many mineral resource and related projects in Australia. These studies have lead them to conclude that the past performance of many project developers does play a major part in any external financial investment for new or expanding resource based projects. In this paper the authors look particularly at the influence of parties outside the direct control of developers and the effect of' these parties on projects and conclude with a number of points as guidelines for potential project developers.

Jan 1, 1980

By Osama El-Fiky

There are many types of deep foundations currently being used in the San Francisco Bay Area, one of the most common being driven precast, prestressed concrete (PC/PS) piles. PC/PS piles are frequently selected for use due to of ease of installation, availability, and relatively low cost. Disadvantages of using PC/PS piles are noise, vibrations, pollution, front-end delays due to indicator pile programs, and reduced flexibility. An acceptable alternative to driven PC/PS piles was selected for construction of foundations for the heavy housing and administrative buildings at the San Francisco County Jail #3 replacement project in San Bruno, California. The pile type selected, the Auger Pressure Grouted Displacement (APGD) pile, was chosen to reduce noise, vibrations, installation time, and cost, and to allow for greater flexibility of installed pile lengths. This paper presents a case history of the use of APGD piles that were substituted for driven PC/PS concrete piles for the subject project. Standard and quick loading pile load tests were performed to confirm adherence with the design criteria originally used for the driven PC/PS concrete piles. The APGD piles were found to increase shear strength around the piles similarly to driven displacement piles. In addition, this paper presents the methodology used in monitoring APGD pile installation.

Jan 1, 2002