Search Documents

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

By Derrick D. Dasenbrock

Three piers of a new river bridge are supported on 1.067 m diameter open-end steel pipe piles. At time of drive, and after pile re-strikes, high-strain dynamic capacity values at plan tip elevations, were as low as 23% of design requirements. Pile lengths were extended 20% to 40% deeper than planned at two piers, driving to rock, impacting both the project cost and schedule. The significant discrepancy between predicted and observed capacity was investigated through a series of coordinated dynamic tests; a full-scale test pile was installed and monitored over 221 days by both dynamic and quasi-static methods. Unusually slow strength gains were observed by dynamic monitoring on all piles installed at the site. CPT soundings were advanced at the test pile and through the pile interior to investigate the soil plug. High-strain dynamic methods were found to have significant limitations in properly assessing the long-term capacity of large-diameter open-end pipe piles during driving and short-term pile re-strikes. As the benefits of large diameter high-capacity open-end pipe piles are numerous, the geotechnical community needs to address appropriate construction monitoring and control of these foundation types to take full advantage of these systems. An improved understanding of the physical effects of pile installation and the impact on soil strength assessment while driving and long term soil strength gain should be developed and incorporated into both design and monitoring procedures to avoid either unsafe or needlessly costly designs.

Jan 1, 2006

By Ihsan Berk Tulu, Mark Van Dyke, Ted Klemetti, Deniz Tuncay

"Longwall abutment loads are influenced by several factors, including depth of cover, pillar sizes, panel dimensions, geological setting, mining height, proximity to gob, intersection type, and size of the gob. How does proximity to the gob affect pillar loading and entry condition? Does the gob influence depend on whether the abutment load is a forward, side, or rear loading? Do non-typical bleeder entry systems follow the traditional front and side abutment loading and extent concepts? If not, will an improved understanding of the combined abutment extent warrant a change in pillar design or standing support in bleeder entries?This paper details observations made in the non-typical bleeder entries of a moderate depth longwall panel; specifically, it explores data collected from borehole pressure cells and roof extensometers, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was the extent and magnitude of the abutment loading experienced due to the extraction of the longwall panels. Due to the layout of the longwall panels and bleeder entries, the borehole pressure cells (BPCs) and roof extensometers did not show much change due to the advancing of the first longwall. However, they did show a noticeable increase due to the second longwall advancement, a maximum of about 4 MPa of pressure increase and 5 mm of roof deformation. The observations of the conditions showed little to no change from before the first longwall panel extraction began to when the second longwall panel had been advanced more than 915 meters. Localized pillar spalling was observed on the corners of the pillars closest to the longwall gob as was an increase in water in the entries. In addition to the observations and instrumentation, numerical modeling was performed to validate modeling procedures against the monitoring results and evaluate the bleeder design. ITASCA Consulting Group’s FLAC3D numerical modeling software was used to evaluate the bleeder entries. The results of the models indicated only a minor increase in load during the extraction of the longwall panels. These models showed a much greater increase in stress due to the development of the gateroad and bleeder entries—about 80% development and 20% longwall extraction. The FLAC3D model showed very good correlation between modeled and expected gateroad loading during panel extraction. The front and side abutment extent modeled was very similar to observations from this and previous panels."

Jan 1, 2019

By Mohammad Djavid

The one-pass tunneling pipe jacking method has often been the most schedule and cost efficient method for the pipe line installation. The main challenges in jacking pipes larger than 108 inches and for longer runs are: transportation and logistics, requiring high jacking forces, keeping line and grades, control of ground surface settlement, providing adequate external lubrication, and the potential of damaging the joints and pipe spigots. In recent years, 144" diameter pipes have been jacked for short runs of up to only 300 feet. In this article design and construction of installation of up to 1,000 linear feet run of 144-inch internal diameter, reinforced concrete pipes without intermediate jacking station in Chicago O?Hare International Airport are discussed. The article also presents discussions regarding the subsurface saturated silt formation, shallow cover, dewatering, jacking and receiving shafts, jacking forces, lubrication and settlement data.

Jan 1, 2008

By Christopher J. Bise

INTRODUCTION The level of analysis for the selection of extraction practices and equipment for surface mining differs significantly from that found in underground mining. In underground mines, manufacturers establish the operating ranges of the equipment, such as continuous miners, loaders, and boring machines, based upon required clearances. Even in conventional mining, the drilling and blasting operation is usually based upon experience. The selection of extraction methods and equipment for surface mining is more complex. Since the equipment is not as confined as in deep mining, and the topography tends to be highly variable over the limits of the mining property, primary extraction equipment must be sized according to reach and capacity. Further, due to the depositional characteristics of the over- burden, drilling and blasting patterns must be well- designed to provide proper fragmentation. The following sections provide a general outline for the selection of surface excavation practices and equipment. The topics covered include drilling and blasting and the selection of both primary extraction equipment (draglines and stripping shovels) and secondary extraction equipment (bulldozers, scrapers, and front-end loaders). EXCAVATION FUNDAMENTALS Before discussing surface excavation, a few concepts need to be defined. A bank cubic yard of material is equal to one cubic yard as it lies in its natural or undisturbed state. A loose cubic yard is that portion of a bank yard that after being disturbed has expanded to measure one cubic yard. Swell is the volume increase of a material when it is removed from the natural state. Finally, load factor is the percentage decrease in the density of a material from its natural state to a loose state. Table 1 summarizes these concepts for various materials. When the amount of overburden to be removed to meet a predetermined production rate is established, a suitable bucket size for the primary stripping equipment must be calculated. The following equation can be used: NBSIZE = TBC/[(OF) (BF)] (1) where NBSIZE is the actual bucket capacity after considering the swell percentage, the bucket fill factor, and the operating efficiency; TBC is the theoretical bucket capacity (TBC = COB/NTCPM); OF is the operating efficiency; BF is the bucket fill factor; COB is the cubic yards of overburden to be removed; NTCPM is the number of theoretical cycles per month [NTCPM = (SMH) (3600)/(CT)]; SMH is the scheduled monthly hours; and CT is the cycle time in seconds. FRAGMENTATION PROCEDURES Drilling Where the strength of overburden material is such that blasting is required prior to excavation, drilling is conducted before using explosives. Two methods of drilling are found in mining-percussion and rotary. Penetration of overburden by percussion drilling is carried out by successive impacts of the bit into the rock. Emphasis in this section will be placed on rotary drilling, because for surface mining it is the most versatile form of overburden penetration. Rotary drilling is conducted by rotating a rigid string of tubular rods to which a rock-cutting bit is attached. The drilling energy is supplied by rotation as well as thrust and the cutting action consists of abrasion, scraping, spalling, or chipping. The size range for rotary-drilled blastholes is from 4 in. to 15 in., with 9 in. and 12 in. being common sizes. There are two types of bits used for rotary drilling-drag and rolling cutter. Drag bits are applicable in soft to medium-soft shales or their equivalents. Since their effectiveness is dependent upon a successful scraping action, drilling thrust is lower for drag bits than for rolling cutter bits; the opposite is true for torque requirements. The bits are usually fitted with replace- able tungsten-carbide cutters. Rolling cutter bits, though available in a two-cone configuration, are usually of the three-cone style (Table 2). The rolling cones have either large steel teeth for drilling through soft formations or small tungsten-car- bide inserts for drilling through hard formations. Table 3 relates bit size and weight to the strength of the rock. The major advantage of rotary drilling is its rapid drilling rate. This is due to the fact that, unlike percussion drilling, rock penetration is uniform with depth. Blasting Effective bank preparation deals not only with the fragmentation of overburden but also with the mini-

Jan 1, 1986

By Sahoo K. C

Traditionally, the blast furnace (BF) has maintained a dominant position as the primary source of iron units. Notwithstanding the efficient nature of the process in respect of its material and energy consumption, the conventional blast furnace route is faced with limitations such as stringent quality metallurgical coke, high capital investment, etc. While BF will continue to retain its predominant position as the foremost ironmaking technology, the alternate processes may also have a role to play. Direct Reduced Iron (DRI) or sponge iron industry is all set to take a firm root in India as one important solution to the problems of shortage of metallurgical coal and ferrous scrap and high investment costs faced by the country's steel industry. The commercial proven DR processes coupled with electric arc furnace (EAF) steelmaking have also offered a viable alternative to the blast furnace - basic oxygen furnace (BF - BOF) route for the installation of integrated plants under specific local conditions. The performance and efficiency of DRI processes mainly depend upon the chemical and physical behaviour of the raw materials especially the iron bearing materials. Iron oxide pellet and sized lump ore constitute the oxide feed stock, while pellets form an ideal feed stock for direct reduction, use of lump ore is economically advantageous because of its lower price. National Mineral Development Corporation Limited (NMDC), being one of the major producer of iron ore in the country since last four decades, has established technology and developed process flowsheets for production of suitable calibrated lump ore for DRI production, besides supplying the natural lump ore for conventional blast furnace requirements. In addition to the above, extensive pilot plant tests have been carried out at the R&D Centre of NMDC for preparation of iron ore concentrates suitable both for direct reduction and blast furnace grade pellet feed using the iron ore fines from its own mines and as well as from the other iron ore mines in the country. For utilisation of the huge quantity of slimes generated in its ore processing plants, NMDC has planned to set up the first commercial plant adopting the smelt reduction process (ROMELT Process) for production of pig iron from Bailadila slimes. The paper mainly deals with various beneficiation techniques adopted for production of DRBF grade pellet feed from iron ore fines. Also presented in the paper, the extensive work carried out at R&D Centre on preparation and evaluation of calibrated lump ore (Natural Pellets), based on which, suitable modifications are incorporated in the ore processing plants of NMDC for production and supply of the same to sponge iron industries.

Jan 1, 1999

THE Great Cobar Company Limited owns 1100 acres of freehold, which include the Great Cobar Oopper Mine and smelters, the Cobar Gold Mine, the Cobar-Ohesney Copper Mine, and the Great Peak Gold Mines.ORE OCCURRENCEThe ore-bodies in the first three mines-namely, Great Cobar Copper Mine, Cobar Gold Mine, and Cobar-Ohesney Oopper Mine are, speaking generally, lenticular deposits of evidently more or less complete metasomatic replacements of the country rock along a line of powerful faulting. These lenses vary from 150 ft. to 400 ft. in length, and from 20 ft. to 100 ft. in width.

Jan 1, 1919

By Basem Sh. Hazzan

In the last four decades significant effort has been devoted to designing piles in expansive clay soils. Nevertheless, only a scant effort has been devoted to the elimination of heave forces acting on the upper part of lightly loaded piles. For this purpose, an investigation site was established in Karmiel in Northern Israel. On this site sixteen unloaded cast-in-situ piles, both uncoated and coated, were installed in a moderately expansive clay soil in the end of summer 1996. The piles were executed to different depths ranging between 2m and 7m and were observed over a period of 27 months. Another nine unloaded cast-in-situ bored piles were installed at the end of summer 1998 for carrying out pullout tests. These piles were embedded two meters from the ground surface. Results obtained from observations and from full-scale static pull out tests showed that separating the piles from the surrounding clay in the active zone by a twin walled sleeve eliminated the heave forces significantly. The scope of the work is, determining of the elimination degree of the heave forces due to the provision of the above sleeve.

Jan 1, 1999

Adsorption of Alkylammoniums in the Interlayer of Montmorillonite and its Effect on the Viscosity of Organo-Montmorillonite Gels

Sep 13, 2010

Colloidal interactions play a critical role in mineral processing, including grinding, physical separation (particularly flotation), dewatering, and tailings management. Despite great energy input in comminution to liberate valuables from gangues, heterocoagulation between valuables and gangues would prevent the separation of valuables from gangues. On the other hand, selective coagulation/flocculation to increase the size of desired fine particles could enhance physical separation and dewatering, while dispersion is needed for fine grinding. To control the state of colloidal dispersions by creating favorable conditions, it is of paramount importance to study colloidal interactions in a relevant system and understand underlying mechanisms. This review summarizes recent advances in developing the-state-of-the-art techniques and novel methods of measuring colloidal forces, including atomic force microscope, surface force apparatus, zeta potential distribution measurement, quartz crystal microbalance with dissipation, and our recently developed integrated dynamic force apparatus. The basic principle of each technique was introduced first, followed by a summary of critical information derived for the relevant mineral processing systems. Finally, the pros and cons of each technique were discussed to emphasize the use of complementary techniques that assist in solving fundamental problems in mineral processing.

By R. Chryst, R. Kus

In the Integrated IT Systems proposed by Przedsie? biorstwo Robót Geologiczno-Wiertniczych—Geological and Drilling Company (PRGW) a network connects a database with all of the departments of a mining division. A key element thereof is the common graphics environment—Micro Station supplied by the firm, Bentley. PRGW’s SoftMine software and GMSI’s CadsMine that are used to design and schedule mining operate in this environment. The digital form of the design project facilitates the verification of information and the integration of technical solutions with SAP R/3 type financial—accounting systems. The system has been successfully implemented in the Brown Coal Mine in Poland.

Jan 1, 2003

By M. V. Mielke, R. E. Hagen, R. L. Bennett

FINE IRON ORES, and concentrates such as those produced from taconite, must be converted to lump form by some process of agglomeration before they can be used effectively in the blast furnace or open hearth. At the present time, four major processes for agglomerating these materials are being used on a commercial scale: sintering, nodulizing, pelletizing and briquetting. IN 1945 U. S. Steel Corp. through its subsidiary the Oliver Iron Mining Div., drew up tentative plans for an agglomerating plant on the Mesabi Range which would include a nodulizing kiln and a sintering machine. The purpose of the plant was two- fold: during its initial operation it would provide data on agglomeration of high grade ore fines, and would help relieve the shortage of ore for open hearth charging. Subsequently, it would be available for agglomerating taconite concentrates. While operating on fines screened from direct ore, it was planned to develop techniques and personnel so that a workable plant would be ready to handle taconite concentrates when the time came.

Jan 1, 1954

By David Norval

Water solidification of mattes, metals, alloys and certain slags with high metal entrainment has customarily not been practiced due to the belief that such processes are too dangerous and unproven in the Pyrometallurgical Industry. Slag granulation on the other hand is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. This paper will examine the most common air solidification processes and compare such processes with water solidification, mainly slag and matte granulation processes and design criteria for safe and reliable operation. Finally, purpose designed granulation and solidification processes will be discussed taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte or alloy responds in similar fashion to a granulation practice.

Jan 1, 2006

Utilizing a very large database from a mined-out area on a South African gold mine, the relative efficacy of a method to mitigate the smoothing effect introduced by the algorithmic constraints imposed by kriging was investigated. Smoothing effects arising from limited data availability are differentiated from the smoothing arising from the application of estimation algorithms. Very little can be done to ameliorate smoothing of estimates because of too little data, barring additional drilling or sampling. However, the smoothing effects resulting from the kriging process are shown to be mitigated by use of an alternative algorithm. The primary criterion in the development of the new algorithm was to avoid re-introducing conditional bias. This paper examines firstly the smoothing effects introduced into estimates via the kriging covariance matrix, secondly the process for ameliorating the smoothing effect, and finally it uses a case study to demonstrate the effectiveness of the new algorithm on a very large database. The database was used to introduce a 60 m by 60 m drilling pattern which in turn was used to model the semi-variogram and produce 30 m by 30 m kriged block estimates. The follow-up database was then re-introduced (roughly 5 m by 5 m grid spacing) and averaged into 30 m by 30 m blocks to provide a direct comparison with the initial estimates. In this way the extent of smoothing and accuracy of the estimates before and after the corrections was tested.

Jan 1, 2014

By P. T. Allsman

INTRODUCTION The honor of being the recipient of the Mining Society's Daniel C. Jackling Award for 1966 imposes on me the responsibility to search for the subject that I would be best qualified to discuss. It seems that my experience in the mineral industry — nearly 15 years in private and 30 years in public employment — should uniquely qualify me to comment upon the relationships between the mining industry, mineral engineering as a profession, and government, and the changing economic, technologic, political and social changes that dictate their relationships. Such conditions, the increasing knowledge of the world mineral resource base, the greater demands of an expanding population with a rising standard of living, shall be evaluated with respect to our profession — mineral engineering. In all of these forty or so years, I have been in close touch with many phases of the mineral and energy resource industries, especially those of the United States. Particularly during the past 10 years, I have had a ringside seat at the "goings on" in Washington. During all of this period I have observed and analyzed many of the problems of the industry and its relations with the government. During the past few years, I have had increased opportunity for doing research and have found a need to learn something about the mathematical techniques that are undergoing such a revival since electronic computers were developed. One of these techniques is multivariate analysis, which is a system for correlating a large number of complex variables. By applying this technique to the seemingly chaotic present-day situation, there emerges a course of steady improvement in the minerals resource industries that wars, depressions, and political strife have failed to obstruct for long. In short, I advocate a need for new concepts in mineral engineering to cope with the changes, pos- sibly adding many more specialized areas on one end of the spectrum, and broad engineer-generalist approaches at the other. The meeting place shall be where the intricate mineral resource problems at the frontier of knowledge merge into the socio-techno-logical problems of the world. HISTORICAL INVOLVEMENT OF GOVERNMENT IN MINERAL RESOURCE PROBLEMS Involvement of government in mineral resource problems undoubtedly is as old as government itself. But passage of the Mining Act of 1866, superseded by the Act of 1872, was the first major entry of our Federal Government into the problems of mining. Passage of the law was necessary to resolve many conflicting claims and disputes in mining. The General Mining Law of 1872 and the Mineral Leasing Laws of 1920 apply to millions of acres of public lands and to certain privately owned land on which the mineral rights have been reserved to the Federal Government. The extensive involvement of government in the mineral industry business today often comes as a shock to the mineral engineer who has begun to climb the ladder to the top in his company. He is often poorly prepared to cope with the situation and becomes frustrated and even hostile. Better knowledge of the role of government perhaps would ease his situation. In our political system, private industry is responsible for producing minerals. To make certain that the production is adequate for a peace-time economy, and to guarantee the Nation's security in an emergency, the Federal Government finds it expedient to develop policy and engage in regulatory, educational, and research activities. A few examples will illustrate the varied role of government in relation to mineral problems. In varying degrees many agencies of the Executive Branch of Government have responsibilities that influence the functioning of the mineral and energy industries. In addition, of course, Congress, the Judiciary, and State and local governments exercise great influence. The Department of the Interior is primarily responsible for activities to promote the development and conservation of mineral and fuel resources, and the

Jan 1, 1967

The importance of timbering, not only from a financial point of view but from an actual mining point of view, is so often overlooked or slightly glossed over by the average expert and investor, that I have thought it would prove interesting to go into the matter and to invite discussion upon the subject. We will first take small veins, or reefs as they are termed in some mining countries; and by small veins it is intended to denote fissures from a few inches to three feet. The ore body is supposed to be confined within well defined walls free from gangue matter, unless the casing can be defined as such. Now, if the walls are smooth and moderately hard, no timbering is required other than the stulls, which are braced from wall to wall in order to form platforms or stages to stope from. Should the reef from wall to wall prove payable, or should the vein be of a character to prohibit cleaning or sorting; and it be determined to send the whole of the stone to the, reduction works, the stuUs should be left in place until the section or block of ground is worked out, in order that if a weak spot in the walls (especially the hanging) occur, it would be possible, without any particularly extra expense or difficulty often times accompanied by danger to brace and secure the slabs. After the block became entirely stoped, it would pay where labour was cheap to remove the majority of timbers to stull another section.

Jan 1, 1901

By Walter Valery, Peter Radziszewski

"The NewCrest Cadia operation boasts the largest SAG mill commissioned last June 1998. A request was made to shed some more light on possible SAG mill charge behaviour. Three different software were used to simulate SAG mill charge behaviour:Mishra/Rajamanis MillSoft DEM charge motion program, Radziszewskis agglomerated DEM charge motion program and Powell/Nuricks MillTraj outer trajectories program. The contexts simulated are: 20/30 % charge volume, 65/75/85 % critical speed using the Hi-Lo lifter configuration specified for the mill as well as a Hi-Lo 60 degre lifter face configuration. Further, lifter interval was also studied to determine the effect on power draft. Power predictions are compared with those obtained during the commissioning period.INTRODUCTIONThe NewCrest Cadia operation is located outside of Orange, New South Wales, Australia. With proven reserves of 190 million tonnes at a grade of 0.75 g/t Au, the mill was designed to process 17 Mtpa (2065 tph) of ore with an 86% copper and 73% gold recovery. The grinding circuit (Fig. 1, Table I) boasts the largest SAG mill (Fig. 2) and was commissioned last June 1998."

Jan 1, 1999

By M. Slatter

The need for anti-corrosion coatings has existed for many years in the ground support industry, but the application requirements have made coating selection limited. Varying groundwater and chemical conditions continually challenge long term coating performance. Traditionally the industry coating preference has been hot-dip galvanizing due to its performance characteristics in highly corrosive environments and low cost nature. However, the galvanized coating has application limitations. This paper highlights some of these limitations and provides selection criteria for a new organic coating developed for one such difficult application, DSI?s Omega BoltPTM Pwhich is an expandable ground support. [ ]

Jan 1, 2009

The use of black and white and colour infrared film in remote sensing of natural resources is reviewed. In heavlly-forested areas such as New Zealand, the main value of the method is in surveying the vegetation cover to detect the existence of plant communities characteristic of specific geological formations. By contrast in arid areas of Australia where the vegetation cover is sparse and where rocks and soils are well exposed, the method can be used in detecting different rock types or other geological differences.

Jan 1, 1972

By J. Janin, J. F. Bougard

Development of improved transportation networks in major urban centers has led more and more to underground construction, the only reasonable solution for decreasing surface traffic congestion. Excavations required by these projects usually cause decompression of the surrounding soil mass which results in subsidence of several centimeters. While these magnitudes of subsidence have no consequences in undeveloped areas, they are often unacceptable in urban areas where existing buildings, structures and utilities are endangered. Recent tunneling projects for the extension of the Paris Metropolitan Transit System (R.A.T.P.) underground network were carried out with this in view and gave rise to the development of a number of innovative techniques for minimizing ground decompression and subsidence. As shown in Figure 1, the recent R.A.T.P. expansion program includes a new express metro, 46 km long, crossing Paris from East to West, and the extension of many existing metro lines in the suburbs. From the start, R.A.T.P. was faced with many unique technical problems for which there was little precedent experience. The structures to be built have large dimensions, with cross-sections typically ranging from 40 to 300 m2, and exceptionally to 600 m2. The new lines are often very deep because the shallow profile is already congested by the existing metro, interceptors, sewers and a very large number of utilities. As a result, new construction is often below ground water level by as much as 20 m. Moreover, the geology varies widely from hard limestone with compressive strength over 1500 kg/cm2 to inconsistent water bearing sand. Finally, curves in the East-West line must have a minimum radius of 500 m which frequently forces the alignment to pass below existing structures, buildings and monuments.

Jan 1, 1974