Search Documents

By Duclerc Fernandes Parra, Ademar B. Lugão, Nilton Lincopan, Fernanda Esposito, Vijaya Rangari

Polymeric hydrogels are natural or synthetic systems, which have gained interest due to their high biocompatibility with soft tissues. These types of hydrogels have been used for wound dressing as a drug delivery system. Here in this study the polymeric hydrogels based wound healing systems were prepared using poly (N-vinyl-2-pyrrolidone) (PVP), poly (ethylene glycol) (PEG), agar and neomycin drug followed by gamma irradiation to promote crosslinking and sterilization. The influence of irradiation process with 25 kGy dose was investigated. The gel fraction and maximum swelling were estimated using physicochemical methods and found about 95% gel fraction and 1100% swelling after 8 h of immersion. Neomycin released from hydrogel was carried out by Liquid Chromatography-Mass Spectrometry method and the drug concentration remained constant for 48 h. Hydrogel/neomycin exhibited antibacterial effects against Staphylococcus aureus. With these results, it can be inferred that hydrogel/neomycin is a suitable candidate for wound dressing.

Mar 1, 2018

By Jr. Koch

Statistical methods applied at the Bureau of Mines Denver Mining Research Center to data from metallic ore bodies were used to evaluate lignite reserves from core data and to predict the extent of lignite horizons in some Texas lignite beds. Six lignite seam units were studied using data from 361 drill holes. The data indicate a total of 214.2 million tons of lignite in the area examined, and probable reserves of 113 million tons in an area 2,000 feet beyond the limits established by the drill holes. It was demonstrated that lignite reserves present in lenticular beds could be reliably determined by statistical techniques, and that core drilling could be optimized to maximum information with minimum drill holes. The technique described is applicable to other coal beds.

Jan 1, 1966

By G. S. Cole, G. F. Bolling

A series of Al-Cu alloys has been cast from constant superheat to solidify either with a hot top or with a free liquid/air interface. All the other variables which affect relative fluid motions were kept constant except the imposition of slow rotations m oscillations of the mold. Depending upon the exact circumstances, evi-dence could be found for the nucleation of equiaxed grains from dendrite bits detached from the columnar zone, or from the free surface, or from solid bits induced at pouring; a special experiment showed the solute buildup during ingot solidification and by inference the reality of constitutional supercooling. All methods of grain nucleation are thus supported. When solidification is arranged in a static mold the columnar- to-equiaxed transition occurs by one of these nucleation paths, subject to the natural decay of temperature gradients which promotes nucleation or the survival of nuclei. But when solidification is forced under special fluid flows it may display odd transitions. In one of these the equiaxed zone is synihesized from. dendrite bits detached from the solid/liquid interface. These survive under the concurrent lowering of temperature gradients and eventually cause transition by impeding columnar growth. GRAIN structure control is desired because real experience shows that specific properties are associated with specific cast grain structures. But since control is thus a matter of need and does not require understanding, much of casting remains art. For example, the manipulation of relative fluid motions in simple ingots provides a control of grain structure development,1-4 but theoretical insight is not required in order to broaden its potential applicability. Fortunately, however, once a variable like fluid flow is recognized it can also provide paths toward new insight. New observations using this variable have provided an insight which is curious. All the theories or descriptions of the columnar-to-equiaxed transition (CET) seem to be supported as long as the appropriate experiment is carried out. In order to develop this idea, let us ignore segregation, the chill zone (until a later section of this paper), and the origin and development of the columnar zone.= The details of questioning how equiaxed material forms in a casting may be divided in two. The first part is simply a questioning of the origin for equi-axed grains: are there fresh nuclei from heterogeneous nucleation, or dendrite bits broken off or melted from the columnar zone or elsewhere,6 or other solid bits surviving from the outset of freezing? The second is more complex, a questioning of the CET: does columnar growth slow down and allow the dominance of equiaxed grains, however they are formed, or do equi-axed grains take over and force columnar growth to stop? This "chicken-or-the-egg" second question can be quite useful, especially because it allows us to delineate the ordinary or NATURAL EQUIAXED ZONE and the induced or SYNTHETIC EQUIAXED ZONE. A natural equiaxed zone occurs if solidification proceeds in the absence of disturbances or extraneous forces such as ultrasonics, stirrings, and so forth. Both the CET theory proposed by Winegard and Chal-mers, 7requiring constitutional supercooling, and the CET theory suggested by Chalmers,8 requiring nuclea-tion only on pouring, pertain to the natural equiaxed zone. The best collating evidence to date for both these theories is contained in the work by Biloni and Chal-mers;9,10 the former theory7 is supported by special versions of the unidirectional growth experiment performed by Plaskett and winegardl1 and the latter theory' is supported in detail for the solidification of small ingots. An equiaxed zone can be synthesized when disturbances caused by forced fluid flows2-4 or other artificial means9,10 break off or melt off dendrite tips from an advancing solid/liquid interface,* if (and only if) temperature gradients in the melt are (forcibly) reduced enough to ensure the survival of these bits of dendrites, 2'3 Willful disturbances even so trivial as those produced by rapping a mold might be included here; as will be shown for example, this follows Southin's suggestion that the free liquid/air interface

Jan 1, 1970

By Jessica M. Wempen, William G. Pariseau, Dallan J. Coons, Michael K. McCarter, Erik C. Westman

The abstract discusses the importance of proper pillar sizing in underground mining for safety and efficiency. It highlights the use of theoretical models, geotechnical measurements, and numerical modeling in predicting pillar behavior. The research focuses on using seismic tomography to image stress changes in a yield pillar at a longwall mine as the longwall face approaches. The study aims to compare the stress distribution imaged using tomography with theoretical models, geotechnical measurements, and numerical models.

Mar 18, 2022

By A. Anderko, R. D. Springer, R. D. Young

A thermodynamic model has been developed for calculating phase equilibria and other properties of multicomponent electrolyte systems. The model has been designed to reproduce the properties of both aqueous and mixed-solvent electrolyte systems ranging from infinite dilution to solid saturation or pure solute limit. The model incorporates formulations for the excess Gibbs energy and standard-state properties coupled with an algorithm for detailed speciation calculations. The excess Gibbs energy model consists of a long-range interaction contribution represented by the Pitzer-Debye-Hiickel expression, a second virial coefficient-type term for specific ionic interactions and a short-range interaction term expressed by the UNIQUAC equation. The accuracy of the model has been demonstrated for common acids and bases and for multicomponent systems containing aluminum species in various environments.

Jan 1, 2005

By C. E. Baltzer

This paper highlights the electric power situation in Canada, and introduces brief explanation of the salient differences between electrical practice in the United States and Canada. The availability of bask energy in the two countries is touched on, also the hydro versus thermal outlook as applying to Canada. De-v2lopment of thermal-electric power is dealt with in some detail, followed by Canada's thermal-electric power requirements, present and future. The fuel requirements for steam-electric generating plant are assessed on the basis of a survey recently made, and the location and size of the major thermal plant operations are given. Fuel contractual obligations on the part ?of suppliers and consumers are mentioned. Finally, an opinion is expressed in regard to the types of f.uel in ?demand on a regional basis with emphasis on the need for coal in the several areas dealt with.

Jan 1, 1958

By A. Sainato, S. J. Schatzel, D. M. Hyman, J. C. LaScola

The Bureau of Mines determined the gas contents of 135 oil shale samples obtained from approximately 630 ft of core drilling. Drilling was done within a projected mining zone of the Cathedral Sluffs Mine, located in the Piceance Basin of western Colorado. Methane contents were determined by the modified direct method, which can measure the volumes of several gases released from or reacted with mine rock without destructive sample treatment. Over the duration of the test, nitrogen was largely unreactive, CO2 increased slightly, oxygen decreased markedly, and methane increased more than the total increase of all contained gases. The gas volumes were normalized per unit sample mass and are given in cubic centimeters per gram. Common time irzdices for test duration of 3, 40, and 125 days were used to compare methane desorption among samples. The means of the sample populations for these indices were 0.0316, 0.114, and 0.195 cm3/g, respectively. These quantities are lower than those reported in a Bureau emissions study at the Horse Draw Mine in the Piceance Basin. Oil shale samples that were gas enriched beyond the mean methane contents frequently contained bitumens and pyrite.

Jan 1, 1987

By Ali Jaberi Zamharir, Abolfazl Shoghian‐Alanaghi, Hossein Aghajani, Arvin Taghizadeh Tabrizi

In this study, the leaching rate of molybdenite concentrate was evaluated in sulfuric medium, and the influence of the diverse oxidants including hydrogen peroxide, manganese oxide, copper sulfate on the leaching rate was studied. Also, the effect of the addition of the ethylene glycol to the hydrogen peroxide was studied and results showed that with the addition of ethylene glycol, the leaching rate is increased 55% from 41% up to 80.3%. The optimum condition is achieved as 0.7 M of H2SO4, 4.4 M of H2O2, and 3.5 M of EG at 30 °C within 4 h of leaching time and 500 rpm. Also, inserting the oxygen with the pressure of 6 bar to the leaching autoclave, the leaching rate is increased more up to 86.4%. Finally, the leaching process was studied kinetically and the determined mode of controlling factor was specified based on the activation energy which equals 46.252 kJ/mole indicating the chemical reaction mode.

Jun 5, 2022

By Chuanguang Bi, Wenbin Dai, Hongtao Wang, Mansheng Chu, Zhenggen Liu

Coke oven gas (COG) injection is considered as one of feasible measures to reduce carbon emission of BF. The effects of COG injection on the reduction of iron-bearing burdens were numerically simulated by means of multi-fluid BF model, which revealed that with increasing COG injection rate, solid temperature gradually decrease, in-furnace H2 concentration increases, the reduction of magnetite and wustite by H2 is evidently accelerated, the reaction rate of wustite by H2 reduction is enhanced and the reduction degree of mixed burdens is strengthened. Under this hydrogen-enriched condition, metallurgical properties of iron-bearing burdens were experimentally investigated. The GB/T13242-91 test results showed that with increasing COG injection rate, the reduction swelling index of oxidized pellets decreases while the reduction ratio of pellets increases. The softening-melting tests suggested that softening interval of mixed burdens increases from 163.6 to 228.3 °C while melting interval decreases from 147.3 to 92.4 °C. The cohesive zone moves downwards and becomes narrow. The permeability of mixed burdens is improved. In terms of metallurgical properties of iron-bearing burdens, COG injection benefits to improve BF performance.

Mar 1, 2017

By A Minchinton

With blasting, all far-field phenomena including, but not limited to, stress wave propagation, fracture, vibration and muck pile formation are intrinsically and irrevocably dependent upon near-field phenomena or mechanisms that we describe using physics-based mathematics typically transcribed into computer codes. The energetics involved in such near- to far-field transitions are not fundamentally relevant as they are simply progenitors of these processes.The notion of explosive energy as a descriptor for explosive or blasting performance is a case in point. These energies, which are generally used in blasting tables, are almost exclusively based on ideal detonation theory alone and do not include the influence of the rock, charge diameter, blasthole length and the late-time dynamic expansion that can be predicted using codes based on non-ideal detonation theory.With decoupled charges in presplits for example, the pressure drop between the charge and the blasthole wall can be simply described to first order using the energy relationship associated with adiabatic expansion. However, a more realistic mechanistic solution involves interacting fluids and turbulence leading to dynamic processes such as the channel effect.CITATION:Minchinton, A, 2015. On the influence of fundamental detonics on blasting practice, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 41–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By W. N. Hamilton

British Columbia is geologically favourable for a rich variety of industrial mineral occurrences. Some have been produced for years, others overlooked until recently. Major production occurs for asbestos, gypsum, limestone, magnesite, silica and sulfur; lesser production for a dozen others. For several of the minerals, potential is much greater than existing production. New production opportunities exist also for diamonds, niobium and REE minerals, fluorspar, kyanite, nepheline syenite, talc, and several others. Alberta, though geologically less diverse, also has many industrial minerals. Limestone, salt and sulfur have the major production; clay and shale, silica, sodium sulfate and a few others lesser production. Opportunities exist for expanded production, and for new production in heavy (Ti -Zr) minerals, formation brines (Ca-Mg-I-Li), and gypsum.

Jan 1, 1987

By D. B. Dreisinger

The zinc pressure leach process developed by Sherritt Gordon, Ltd. permits the direct leaching of sulphide concentrates according to the overall reaction, ZnS +H,zS04 +402.+ZnS04+H20 +S0 The kinetics of the leach are affected by three rate controlling steps; ( l) oxygen mass transfer from the gas to the leach solution, (2) homogeneous oxidation of ferric ion to ferric ion by dissolved 011.ygen and (3) ferric ion leaching of zinc sulphide in the presence of a sulphur dispersing detergent (lignin sulphonic acid). Fundamental studies have been conducted to identify the factors that influence the kinetics of each individual rate controlling step. Oxygen mass transfer studies have been directed toward optimization of the agitator configuration for solids mixing and gas pumping from the atmosphere above the leach slurry. The rate of ferrous oxidation by molecular oxygen and the rate of zinc sulphide leaching by ferric ion have been studied over a wide range of temperature and solution compositions. The study of zinc sulphide leaching by ferric ion was supplemented by a series of interfacial tension measurements in the liquid sulphur - zinc sulphate solution system. The various kinetic studies have been summarized in terms of the importance of each rate to the performance of the process.

Jan 1, 1990

By T. W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (water box) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 % reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2012

By L H. Warren

The types of equipment available for generating a plasma have been reviewed. The efficiency and potential of the plasma generating equipment used in performing extractive metallurgical reactions have been determined. A general classification of the reactions that might be per-formed in a plasma has been proposed. Experimental work done on extractive metallurgical plasma reactions, heat transfer between the plasma and solids, and the quench of the products of plasma reaction has been summarized. From the preliminary results it appears that the high-intensity are or the transpiration-cooled anode plasma torch offer the most promising areas for further research. C ONSIDERABLE world-wide research effort is currently being devoted to the development of processing technologies which employ the new high-temperature generating devices that have appeared over the past few years. The plasma flames produced by these devices offer the potential for subjecting materials to any single gas or mixture of gases at temperatures up to 20,000°K. With these conditions available, many reactions in extractive metallurgy,

Jan 1, 1965

By X Tian, J Forster, A Olmsted, E R. Bobicki, M Goldbaum, D Boucher, C A. Pickles

As the global demand for metal values expands, it becomes increasingly important to create more sustainable mining operations. Consequently, considerable research and technology development is required to produce processes which are both more energy efficient and have a minimal environmental impact. One potential technology is the utilisation of microwave pre-treatment to reduce the energy requirements in comminution. Microwaves can preferentially heat the valuable mineral phases in an ore and the resulting differential thermal expansion leads to the formation of microfractures along the grain boundaries. As a result of the preferential heating, ore competency is reduced, mineral liberation is enhanced, a coarser grind size can be employed, and plant throughput can be increased. Furthermore, microwave pre-treatment can be combined with advanced ore sorting, to decrease the quantity of gangue material processed downstream and hence reduce tailings production. Previous studies on the microwave treatment of ores over the last 30 years have mainly been limited to low power bench-scale studies and there is a paucity of information on pilot and/or commercial scale studies. In the present research, the microwave heating behaviours of over 40 ores have been studied at the bench-scale. These results were used to generate a database, from which a unique classification system was developed. This system was used to rank the amenability of any given ore for microwave pre-treatment. This knowledge can be employed to predict the performance of the ores in the high-power pilot scale tests and thus can be used as a pre-screening tool. The effects of high-power microwave pre-treatment on grindability and liberation were reported. Additionally, the ore sorting potential was evaluated using a combination of X-ray transmission (XRT) and microwave infrared (MW/IR).

Aug 24, 2022

By John A. Herbst, Gerald H. Luttrell, Jaisen N. Kohmuench, Aaron Noble, Michael J. Mankosa

The HydroFloat TM is an innovative fluidized-bed separator that can substantially increase the upper particle size that can be successfully treated by flotation. Recent studies conducted using laboratory, bench-scale and pilot-scale equipment indicate that this technology can be used to float coarse sulfide middlings that cannot be recovered by conventional flotation machines. Recent data collected from pilotscale tests conducted at a base metal concentrator indicate that this technology can float middlings particles as large as 850 microns in diameter containing as little as 1% exposed hydrophobic mineral. As such, the crossover of this technology into the base metals industry has the potential to substantially reduce grinding costs and increase concentrator recovery/capacity through the use of split-feed circuitry. The split-feed concept, which is often used for upgrading industrial minerals, involves segregation of the feed into more than one size class followed by subsequent upgrading using mills/separators/reagents specifically optimized for each size class. In this article, a split-feed circuit is described that utilizes two stages of classifying cyclones in conjunction with the HydroFloat_ separator. The circuit is designed to recover, recycle and regrind coarse middlings containing small amounts of valuable mineral while simultaneously rejecting coarse well-liberated siliceous gangue so that mill throughput can be increased. Simulation data conducted using well-known process models suggest that this approach can increase existing primary mill capacity by up to 25% with only modest investments in new classifying and flotation equipment.

Jan 1, 2016

By Graeme Heyes, Warren J. Bruckard, Michael A. Somerville

"A limited series of laboratory batch flotation tests was conducted on a suite of calcium-ferrite-based slags made in laboratory smelting trials. The smelting tests were conducted as part of a wider CSIRO Minerals’ research project aimed at developing a single-stage continuous copper-making process. The objective of the flotation work was to maximise copper recovery and iron rejection from slags made in the process.The slags treated included a reduced low copper slag, an oxidised high copper slag composite, and a very reduced low copper self-pulverising slag. The copper content of the slags varied from 2.9% to 14% Cu. The copper was present as metallic copper, oxide copper and copper-calcium ferrite phases with the phase mix related to smelting conditions. The slags were crushed, ground, wet-screened at 355 or 210 µm to remove coarse metallic particles of copper, and floated at natural pH (about pH 11) using reagents and conditions appropriate for the selective recovery of the copper phases.In rougher/scavenger tests on the reduced low copper and self-pulverising slags copper recoveries above 92% were obtained with copper enrichment ratios varying between 2.3 and 2.9. For the oxidised high copper slag copper recoveries were poorer - only 47% of the copper was recovered with an enrichment ratio of 3.3. The presence of the slow floating copper-ferrite phases in the slags limited further (selective) copper recovery. Ageing of the high copper slag, that is, a significant delay between grinding and flotation, resulted in a deterioration of the copper flotation response.The critical parameter affecting the flotation of copper from direct converting slags was found to be the form of the copper in the slag. Slags containing a higher proportion of the more desirable form of copper for flotation will provide the best opportunity for high copper recoveries to be consistently obtained, allowing improvements in the economics of the overall copper-making process."

Jan 1, 2003

By Victor Azbe

Azbe System of Controlled Calcination To obtain good and cheap lime there are certain fundamental requirements that need to be satisfied. These are : (1) Proper combustion of fuel and steady supply of heat to the kiln. (2) Proper heat distribution in the kiln. (3) Uniform drawing of lime through the several shaft sections. (4) Complete cooling of the lime and recovery of the heat. (5) Temperature control of the hot zone by economical means. (6) Ample draft to obtain high capacity. (7) Arrangements to facilitate operation. Figure 17 shows diagrammatically one of the smaller kilns, intended for large stone. Such a kiln can be supplied with gas from a centrally located automatic gas producer, or, as shown, from an integral producer located snugly against the kiln. These producers make very good gas and have a gasification capacity of either 10 or 15 tons of coal a day. The producers have water-sealed ash pits, a rather thick fuel bed that is conducive to the making of high-CO gas, and are under forced draft. No steam is used. Clinkering is prevented by admixing some spent gas from the kiln with the air. Coal feeding is from a coal bunker through spouts into the hoppers over the producer. This is done, at proper intervals, by manual operation of slides, but it is planned to install mechanical feeders. Central mechanical gas producers have the advantage of requiring little labour, but the blowing of soot is a problem, as also is the proper distribution of the gas among several kilns. In the case of integral gas producers, soot from the centre burner is blown back into the producer to be burned, and the supply of gas to the kiln is controlled by regulation of air to the producer. In large plants, the mechanical producer may be preferable, but in small ones, the integral producer is cheaper, better, and more reliable. The kiln shown in Figure 17 is suitable for both systems of gas supply. It will be noticed that there are no side gas burners. All gas enters the kiln through the centre burner in a manner that permits any desired amount of gas to be directed to any of the kiln sections by the aid of regulating slides.

Jan 1, 1946

By A. J. Teske

Sustainable Development is a very broad initiative in the mining industry, with major components running over the entire life of the mine. It likely commences with pre-exploration permitting and continues to post-mining final closure and possible land reuse. Most major mining corporations embrace the sustainability initiative, either out of a sense of social responsibility or out of necessity in order to continue doing business. But many may view the overall initiative as an added ?cost of doing business.? In many elements of sustainability, there clearly can be added cost ? some as simple as complying with self-imposed sustainability reporting. Fortunately, one major element of sustainable development can clearly be shown to reduce costs ? energy resource management. This paper will describe how the mining industry sustainable development effort differs from other industries, but can benefit from their experience in energy resource management. The mining industry can utilize proven methods from other industries to further their energy management efforts. In addition, many of the resources developed and employed to promote better energy resource management in non-mining industrial settings will be listed.

Jan 1, 2010

By W. P. Haynes

ESTIMATED United States crude-oil production during 1943 established a new annual peak of 1,500,000,000 barrels, a daily average of 4,118,000 barrels. This would be an increase of 315,000 barrels per day, or 8 per cent over 1942 and 7 per cent over 1941, the previous peak. During the first ten months of the year, production jumped from 3,782,000 barrels per day in January to 4,400,000 in October. Available data for the last two months of the year indicate a leveling off of this trend, with daily rates slightly above 4,400,000 barrels.

Jan 1, 1944