Search Documents

By Alec M. Crowell, C. H. Thigpen

Continuing the increase in production of crude oil and condensate started in 1937, the oil fields of South Arkansas reached a 13-year peak with 26,570,704 bbl. for the year 1942. The stability of the production branch of the industry in the area is demonstrated by Fig. I, which reflects the fact that although the number of producing wells in the state has declined from 3280 in 1931 to 2957 at the end of 1942, total production has continuously increased since the beginning of 1937. This is because all fields discovered since Jan. I, 1937, have observed spacing patterns up to one well to each 160 surface acres, the dual completion of wells where there is more than one producing horizon Eight new pools were brought into production in South Arkansas during 1942 (Fig. 2) They increased the state's crude oil and condensate reserve by 121,000,000 bbl., bringing the total recoverable reserve figure to 450,000,000 bbl. (Table 3) as of Jan. I, 1943. Abandonment of wells in the stripper areas of the state increased by 32 per cent over the preceding year, there having been 142 wells permanently abandoned in 1942. For economic reasons 279 wells were temporarily shut down as of Dec. 31, 1942. A price increase may start these wells to pumping again and also be the incentive toward the commencing of several secondary recovery projects in the fields discovered between 1922 and 1937. There were 149 wells brought into production in 1942 as against 119 for the

Jan 1, 1943

By C. H. Thigpen, Alec M. Crowell

Continuing the increase in production of crude oil and condensate started in 1937, the oil fields of South Arkansas reached a 13-year peak with 26,570,704 bbl. for the year 1942. The stability of the production branch of the industry in the area is demonstrated by Fig. I, which reflects the fact that although the number of producing wells in the state has declined from 3280 in 1931 to 2957 at the end of 1942, total production has continuously increased since the beginning of 1937. This is because all fields discovered since Jan. I, 1937, have observed spacing patterns up to one well to each 160 surface acres, the dual completion of wells where there is more than one producing horizon Eight new pools were brought into production in South Arkansas during 1942 (Fig. 2) They increased the state's crude oil and condensate reserve by 121,000,000 bbl., bringing the total recoverable reserve figure to 450,000,000 bbl. (Table 3) as of Jan. I, 1943. Abandonment of wells in the stripper areas of the state increased by 32 per cent over the preceding year, there having been 142 wells permanently abandoned in 1942. For economic reasons 279 wells were temporarily shut down as of Dec. 31, 1942. A price increase may start these wells to pumping again and also be the incentive toward the commencing of several secondary recovery projects in the fields discovered between 1922 and 1937. There were 149 wells brought into production in 1942 as against 119 for the

Jan 1, 1943

By Chen-Ming Kuo, Esher Hsu

"Under the 4-in-1 recycling system, Taiwan producers and importers who using packaging containers have responsibility to pay the recycling fees for recycling the waste packaging containers they produced or imported; while the collectors/recycling plants who collect/sort/recover waste packaging containers receive subsidy for conducting recycling. A reasonable pricing for recycling charge and subsidy is a way for sustainability of the recycling. The objective of this study is to provide an amending mechanism for product charge and recycling subsidy in response to the social economic changes. This study employs a regression analysis and cost adjusting model to link the factors used for calculating product charge and recycling subsidy on recycling waste packaging containers with socio-economic indicators, raw material prices, wholesale prices, and secondary material prices. Study results provide estimated models to EPA in Taiwan for amending product charge and recycling subsidy in response to the social economic changes.IntroductionUnder ""4-in-1"" recycling system in Taiwan, waste packaging containers are officially announced to be recycled. The waste packaging containers announced to be recycled include iron cans, aluminum cans, glass bottles, plastic containers, paper containers, aluminum foiled paper packs. In order to compensate the recycling system, EPA charges associated manufacturers and importers for recycling fee and subsidies recyclers to create the economic incentive for raising recycling performance. Basically, the budget for subsidy recyclers is from the recycling charge. That means if we want to increase recycling efficiency by increasing subsidy to recyclers then the manufacturers and importers have to pay more for reaching financial balance of recycling foundation. The benefit of recyclers and fee payers are always conflicted. The recycling charge and subsidy is thus argued by fee payers and subsidy receivers all the time. A reasonable pricing for recycling charge and subsidy is the only way to keep the recycling system sustainable. Moreover, a suitable mechanism has to be changed along with the changing social economic condition. The recycling performances and effectiveness of this recycling system is also highly dependent on the pricing mechanism. This study intends to provide an amending mechanism for product charge and recycling subsidy in response to the social economic change. Related previous studies about recycling system in Taiwan with its performance include Hsu and Kuo (2002, 2005), Bor, Chien, and Hsu (2004) and Hsu (1999). Hsu and Kuo [1] estimated total production values of recycling and evaluated the performance of recycling performance based upon the estimated production values."

Jan 1, 2011

By Donald A. Voigt

This publication is intended as a guide for persons responsible for obtaining classifications and approvals Tor explosive compounds, mixtures, or devices from the U.S. Department of Transportation (DOT). It deals with the procedures for obtaining a recommendation for classification of an explosive compound, mixture, or device through the Bureau of Mines. Completion of the procedures detailed in this guide is necessary to obtain a final classification of an explosive compound, mixture, or device and assignment of an "EX" number by DOT, which will allow the producer to offer the explosive for shipment within the United States. This guide also gives procedures for obtaining United Nations (U.N.) classification for shipping outside the United States.

Jan 1, 1990

By E. D. Gardner

AGAIN in 1945, the fourth year of World War 11, the American mining industry met the necessary demand made upon it for metals. Lack of labor prevented full production in some districts; maximum output, however, was maintained with the man power available. Development work and maintenance of mechanical equipment were neglected in favor of immediate production. Drafting of the younger men continued throughout the year, and the loss of personnel to war industries with higher wage rates continued up to "V-J" Day, Aug. 14. Labor shortages were more critical in 1945 than in 1944 though the man-power situation eased for some districts in the last quarter of the year. The trend in mining for the most part was to increase tons per man-shift by continued increased mechanization and refinements in methods and practices; larger equipment was installed where practicable. Labor shortages, together with the current higher wage rates, have advanced mechanization several years ahead of normal progress. The manpower shortage and the employment of inexperienced men had the effect of decreasing the average efficiency of the individual workman, but this condition was largely balanced by improved organization, greater efforts to improve labor relationship, and increased use of incentive pay systems. Safety instruction was emphasized, personnel contacts were increased, and more frequent foremen meetings were held to clarify contract agreements. Many of the large companies maintained schools to train green workmen.

Jan 1, 1946

By Edie Trimmer

Utah statute defines sovereign lands as "those lands lying below the ordinary high water mark of navigable bodies of water at the date of statehood, and owned by the state by virtue of its sovereignty." The lands within the bed of Great Salt Lake (GSL) are, by this definition, sovereign lands, acquired at statehood in 1896 in accordance with the "equal footing" doctrine, granting each state control and ownership of navigable waters and the lands underneath those waters within its borders. Under public trust doctrine, the state, as trustee for the people, bears responsibility for preserving and protecting the right of the public to use of the waters for navigation, commerce, fishing, recreation, and wildlife habitat. Also by statute, sovereign lands are defined as "state lands," to be managed by "multiple use sustained-yield principles." The Division of Forestry, Fire and State Lands is given management authority for sovereign lands and, as manager, has responsibility to prepare comprehensive plans, initiate studies of the lake and its resources, implement comprehensive plans through state and local entities, and coordinate the activities of various divisions within the Department of Natural Resources (DNR). The Division of Forestry, Fire and State Lands also has responsibility for management of mineral leasing on sovereign lands. The many resources on the lake--water, minerals, wildlife, recreation, archeological and historical values--are managed by as many state agencies which occasionally creates conflicts. The brines of GSL contain several ions that crystalize into valuable minerals during evaporation. The major ions in the lake are, in order of relative abundance, chloride, sodium, sulfate, magnesium, and potassium. Mineral products which are currently extracted from lake brines are sodium chloride, magnesium chloride brine which can be sold as flake magnesium chloride or further processed into magnesium and chlorine gas, and potassium sulfate. Mineral products which have potential for extraction include gypsum, sodium sulfate, and trace amounts of lithium, boron, and bromine. The GSL contained an estimated 4.3 billion short tons (st) (3.9 billion metric tons [mt]) of dissolved salts in 1998. Utah Geological Survey (UGS) estimates of the dissolved salt content in GSL have fluctuated from 4.0 to 5.5 billion st (3.6 to 5.0 billion mt) due to the dynamic conditions in the lake as salts are precipitated and redissolved, and due to the diversion of brines from GSL, such as the West Desert Pumping Project. The lake has four areas of varying salinity, separated by dikes or other man-made structures: north arm and Stansbury Bay brines at near saturation (25 to 27 percent total dissolved solids [TDS]); the main body of the south arm with concentrations ranging from 7 to 15 percent TDS as lake elevations fluctuate; the waters in Farmington Bay at approximately 3 to 5 percent TDS; and Bear River Bay at <1 to 7 percent TDS. The percent TDS in Bear River Bay fluctuates with lake level, and changes in Bear River inflow. The transfer of salts from the south arm to the north arm has raised questions about the viability of the mineral and brine shrimp industries. The UGS and the U.S. Geological Survey (USGS) continue to monitor salinities at designated sites on the lake to document changing lake salinity. A recurrent theme is that placement of dikes and diversions can have significant and rapid impacts on various conditions in the lake. Hydrocarbon resources on the lake are significant, but presently undeveloped. The hydrocarbons are low gravity (4 to 9 degree API) and tar-like, contain high nitrogen concentrations, and up to 12 percent sulfur. The unusual characteristics of the oil have been the subject of studies by chemists at Weber State University and University Louis Pasteur de Strasbourg. However, these resources are difficult, and at present, uneconomic to extract using current technology because of the nature of the hydrocarbons, and production in "an offshore, highly saline environment." Oolitic sand deposits make up many of the beaches and shorelines around the lake. Because of their high calcium carbonate content, oolites have been used by Magnesium Corporation of America (MagCorp) and its predecessors for acid neutralization and dike construction. Oolites are also used in very minor amounts in flower drying. The Utah Division of Oil, Gas and Mining reports up to 130,000 st (118,000 mt) mined annually by MagCorp from U.S. Bureau of Land Management (BLM) lands adjacent to GSL. Currently, there are twelve producing mineral leases which generated slightly more than $1,000,000 in royalties during calendar year 1998. IMC Kalium Ogden Corp. (IMC Kalium) produces potassium sulfate and magnesium chloride from brines concentrated through solar evaporation in Bear River Bay and Clyman Bay. By-product sodium chloride is transferred to IMC Salt, which packages and sells the salt. MagCorp produces magnesium metal from brines concentrated in Stansbury Bay. Cargill Salt produces sodium chloride from brines provided by MagCorp under a lease agreement. Morton Salt produces salt at the southeast end of Stansbury Island. Lastly, North Shore Limited produces cocentrated brines for use in dietary and mineral/vitamin supplements near Spring Bay in the north arm of the lake. Producers of magnesium, potash, and salt from GSL contribute significantly to the value of metals and industrial minerals in Utah. Together these companies contribute approximately $240 million in gross value, or 18 percent of the value of the state&apos;s nonfuel mineral production. Most of this production is exported.

Jan 1, 2001

By J. Ramirez-Castro, J. A. Finch

"Galena is the finest component of the product of a closed-circuit grind treating a lead-zinc ore, largely due to preferential recycling of this high-density mineral by the cyclone. For example, at the Pine Point Mines concentrator, for ~ 55% -200 mesh over-all, the galena will be close to 95% -200 mesh. This sliming of the lead can limit recovery, selectivity and dewatering. A proposed circuit modification to reduce the sliming is to incorporate a unit cell. A simulator was constructed to study the No. 3 grinding circuit at Pine Point modified by a unit cell on ball mill discharge (BMD).The simulator used a cumulative size basis rate-of-breakage with plug flow ball mill model, the parameters being obtained by laboratory grinding tests. Flotation and the cyclone models used a cumulative recovery/size matrix. The behaviour of each mineral, galena, sphalerite, pyrite and calcite/dolomite, was simulated. Simulation was adapted to a programmable calculator. A close fit to the existing circuit performance at two tonnages and mineral mixes was established.The simulator showed that the modified circuit could significantly coarsen the Pb grind, from 95% to —50% -200 mesh, depending on recovery, without substantially altering the size of the other minerals. The other principal findings were: compared to laboratory flotation tests on existing circuit BMD, the unit cell concentrate (CONC) will be coarser and markedly lower in grade; relatively low unit cell stage recoveries are desirable, because the cyclone scavenges the tail to give a circuit recovery which is higher than the unit cell stage recovery; unit cell stage recovery should not exceed the cyclone stage recovery, as the latter is the maximum circuit recovery; low unit cell stage recovery helps offset the disadvantage of the high flow at BMD; other high-density minerals will also be scavenged into the CONC, as illustrated by pyrite, making CONC quality difficult to maintain; density control of BMD flotation does not greatly alter feed density to the cyclone or ball mill.Possible plant metallurgy is forecast for a CONC diverted to final lead concentrate."

Jan 1, 1980

By T. T. Read

TWO papers on health and safety were given Thursday afternoon when a joint session of the Health and Safety Committee and the Mining Methods Committee was held. T. T. Read presided and the first paper, on ventilation at Climax, was presented by the author, L. H. Glanville. In the subsequent discussion by Cloyd M. Smith, P. B. Bucky, B. F. Tillson, D. F. Haley, J. L. G. Weysser, and others a number of interesting points not covered by the paper, which appears in full in the January Mining Technology, were brought out. Ventilation troubles in mines so often hinge on the air being too hot and damp that it was interesting to hear of one where it is frequently too cold and too dry.

Jan 1, 1943

By M. J. Richards

Spontaneous combustion caused by the movement of air through the waste is a major problem. Combat methods attempt to exclude oxygen rich air, but little is known about airflow through the waste. The use of a tracer gas technique to monitor the flow of nitrogen from an injection hole during inertisation is described. Correlations are drawn between barometric pressure changes and the nitrogen entering the waste. As no information was obtained about airflow and oxidation zones, a second experiment was conducted to sample from the waste, but the results were inconclusive. A finite element method developed to model the pressure and airflow distribution, under steady state and nitrogen injection conditions is outlined

Jan 1, 1987

By W. F. Domis, F. von Gemmingen, F. Garofalo

The effect of rain size on the creep behavior of an austenitic iron-base alloy has been studied at 1300° F under conditions of constant stress. The average grain diameter varied between 9 and 190 p (ASTM 10.7-2). The subgrain size and apparent activation energy for creep were not found to depend in any systematic manner on gain size. Grain hozmdary serrations were observed in all specimens tested. The variation of the secondary-creep rate, 2,, with the pain diameter, 1, is given by: es = K(213m + 1 )/l.]; 1, is the grain diameter zohere is reaches a minimum. Results in the literature shoujthat 1,increases as the temperature increases. At low creep temperatures is is therefore proportional to 12, at intermediate temperatures <, exhibits a minimum, and at high creep temperatures is is proportional to 1/1. The dependence ofis on the stress, u, is given by: t, = A" (sinh acrln, a and n show little variation with 1. The dependence of A" on 1 is given by: A" = KA[(21k + 13)/1]. For 1 » >>lmn = 4, and at constant values 01- isat lozu stress levels, the steady-state stress is given by the Hall-Petch relation. The variation of c, with grain size is believed to he associated particularly with grain boundary generation of dislocations which becomes more important with increasing temperatures. SEEMINGLY inconsistent experimental findings have led to a certain amount of confusion concerning the effect of grain size on creep behavior. The confusion is attributed to a lack of test results obtained over sufficiently wide ranges in grain size, stress, and temperature. Experimental results presented in this paper and results available in the literature1-5 show a consistent behavior and lead to a unified concept for the dependence of secondary-or steady-state creep rate on grain size. In accordance with this concept, which is substantiated experimentally, secondary-creep rate should increase with increasing grain diameter at low creep temperatures, leading to greater creep strengths for fine-grained materials. At intermediate temperatures the secondary-creep rate should decrease to a minimum and then increase as the grain size is increased. At high creep temperatures the secondary-creep rate should decrease with increasing grain size, leading to greater creep strengths for coarse-grained materials. Whether a temperature is high or low for creep in a metal or alloy depends primarily on its melting temperature. MATERIAL AND TEST PROCEDURES The material tested was an austenitic iron-base alloy of the following composition (wt pct): C, 0.005; N, 0.017; Mn, 1.26; Ni, 14.21; and Cr, 17.18. Two 15 -lb ingots were forged and hot-rolled to 5/8-in.-diam bars which were then cold-rolled and cold-swaged to a diameter of 0.49 in. These were sectioned into 3-in.-long blanks and heat-treated at various temperatures to obtain different grain sizes. The procedures employed and the results obtained are summarized in Table I. The secondary treatment at 1400° F followed the primary treatment without intermediate cooling to room temperature. This final treatment was employed to minimize various effects arising from heating to different temperatures during the primary treatment, particularly differences in intragranular dislocation structure, segregation of interstitial atoms at grain boundaries, and density of grain boundary ledges. The intragranular dislocation structure was examined by electron transmission metallography after each of the treatments described in Table I. Isolated dislocations and a few tangles were observed but no evidence of subgrains was found after any of the treatments. No grain-size effect was evident on the density and distribution of dislocations. Stabilization of grain boundary structure is particularly important because, as will be discussed later, grain boundaries influence high-temperature creep behavior. Magnetic-permeability measurements after each treatment and

Jan 1, 1964

Construction workers may be exposed to hazardous dust containing crystalline silica during site preparation when drilling systems are used. The National Institute for Occupational Safety and Health (NIOSH) found that drill dust could be decreased by using wet or dry dust reduction engineering controls, enclosed cabs, and implementing a dust control program.

Jan 1, 2009

By G. B. Gould

Every mathematical statement of a measure of anything (as distinguished from a count&apos;) is followed by a qualification—always implied if not explicity stated—-that the statement is only an estimate, which may vary from absolute accuracy within certain limits, according to the accuracy of the measuring instrument. This basic fact, so obvious to engineers, is not so well understood by many that make use of laboratory coal tests. The tolerances that must be allowed in measurements of coal quality are very important in both their commercial and engineering applications—and the significance of these tolerances depends upon the use made of the laboratory coal test. Only in recent years has there been any intensive study of this question of tolerances as applied to measurements of coal quality. There is very little in our published literature on the subject, and what has been published is not readily comprehended by those who sell coal, or buy coal and use it, unless they happen to have made a study of the subject themselves. There is great need for more widespread understanding of what lias been discovered and how it applies to the use of laboratory coal tests. What follows is an attempt to condense into a few pages the results of the major investigations so far reported, and to explain their meaning in simple nontechnical language, with the addition of some recent illustrative experiments. Determining Deviations in Quality It is necessary at the outset to distinguish between: (I) the accuracy with which one test indicates the quality on one lot of coal; and (2) the accuracy with which a test of one lot of coal represents the average quality of a commercial product, of which the buyer will presumably receive a series of shipments—perhaps many thousands of tons. It is necessary to make this distinction because coal is a variable material—a heterogeneous mixture of a variety of components—the quality of which will vary from one lot to another. Therefore an absolutely accurate determination of the quality (if that were possible) of one lot of a coal is an

Jan 1, 1938

By G. B. Gould

Every mathematical statement of a measure of anything (as distinguished from a count&apos;) is followed by a qualification—always implied if not explicity stated—-that the statement is only an estimate, which may vary from absolute accuracy within certain limits, according to the accuracy of the measuring instrument. This basic fact, so obvious to engineers, is not so well understood by many that make use of laboratory coal tests. The tolerances that must be allowed in measurements of coal quality are very important in both their commercial and engineering applications—and the significance of these tolerances depends upon the use made of the laboratory coal test. Only in recent years has there been any intensive study of this question of tolerances as applied to measurements of coal quality. There is very little in our published literature on the subject, and what has been published is not readily comprehended by those who sell coal, or buy coal and use it, unless they happen to have made a study of the subject themselves. There is great need for more widespread understanding of what lias been discovered and how it applies to the use of laboratory coal tests. What follows is an attempt to condense into a few pages the results of the major investigations so far reported, and to explain their meaning in simple nontechnical language, with the addition of some recent illustrative experiments. Determining Deviations in Quality It is necessary at the outset to distinguish between: (I) the accuracy with which one test indicates the quality on one lot of coal; and (2) the accuracy with which a test of one lot of coal represents the average quality of a commercial product, of which the buyer will presumably receive a series of shipments—perhaps many thousands of tons. It is necessary to make this distinction because coal is a variable material—a heterogeneous mixture of a variety of components—the quality of which will vary from one lot to another. Therefore an absolutely accurate determination of the quality (if that were possible) of one lot of a coal is an

Jan 1, 1938

By A. Ignatow

"A review is made of some of the principal factors and conditions that are, and will be, important to the over-all market climate for asbestos fibre and for the future of Canada&apos;s asbestos industry: - health hazard associated with asbestos exposure;- uncertain international regulatory environment for continued asbestos use;- adverse public reaction to asbestos;- product liability/litigation costs (U.S.A. primarily);- promotion of substitution by governments and asbestos user industries; and- minimal product and market development efforts by asbestos producing and consuming industries.In addition, Canadian producers, who export some 95 per cent of their production, face additional constraints:- dramatically reduced integration with asbestos-consuming industries;- 60 per cent of exports to most rapidly declining markets (U.S.A., Europe);- increased competition from offshore producers favourably located to growth markets in developing countries;- increasing production costs;- a strong dollar;- disadvantageous freight rates; and- loss of price leadership and price erosion.Future market trends, as well as prospects for Canada&apos;s asbestos industry, will be projected in this paper.Economic FactorsTable 1 presents asbestos fibre production in all countries for the period 1980-82. In certain instances, e.g. U.S.S.R. and China, these are capacity estimates as production statistics are not officially published. The U.S.S.R, by far, is the world&apos;s largest producer accounting for some 50 per cent of world production, though most production is consumed internally or by COMECON countries. It is estimated that some 700 plants produce asbestos-containing products within the U.S.S.R.Canada accounts for some 25 per cent of world production though it ranks first in world trade. Other important producers are South Africa Zimbabwe, Brazil and Italy. Since 1979, Canada&apos;s asbestos mining industry has experienced a dramatic drop in production and exports of asbestos fibre, as demonstrated in Table 2."

Jan 1, 1985

By R. Carson Dalzell

The use of nuclear fission for chemical process heat offers the special advantage of high temperature, limited only by materials of construction. The process heat may be supplied economically at elevated pressures, since no compression of combustion air is required. For the initial effort in developing a high-temperature reactor, the indirect cycle, using helium as the heat-transfer medium, was chosen. The major problems are the design of high-temperature fuel elements, construction of an exchanger to transfer heat to process streams in the range of 2,500° F., and development of compressors capable of recycling helium at 1,000° F. and above. A conceptual design of a nuclear reactor to furnish process heat for coal gasification has been made. Spherical fuel elements utilizing a graphite structure, impregnated with uranium carbide fuel, were chosen, as spheres offer the possibility of easier loading and unloading of the reactor. Calculations of pressure drop and gas-pumping power for the system are included.

Jan 1, 1959

By Moeller T

The Bottle Creek mine, when opened next month, will consist of three open cuts, Emu, VB and Boags, feeding ore to a central mill. The open cuts cover a strike length of 4.5 kilometres which forms part of a linear structure, which can be traced geochemically for 26.0 kilometres. With the exception of a few small gossanous outcrops at Emu, the deposits are completely covered with insitu laterite and alluvial overburden. Since its discovery in 1984, the deposit has been subjected to three major reverse circulation (RC) drilling programmes which have successively closed up the drill spacing on the main mineralized zone to 25m horizontally and less than 25m vertically. All resource calculations have been based primarily on samples of RC drill cuttings from these programmes. Ore reserve calculations have been completed after each drilling phase. They began with a simple polygonal technique, progressed through two sectional half-distance calculations and are now being completed with a 3-D geostatistical technique. Because of the style of mineralization, Norgold personnel paid particular attention to assessing the variability of the mineralization by using repeat samples, repeat analysis and diamond drill vs RC comparisons. In addition, close attention has been paid to obtaining an accurate estimate of the global SG of the ore bodies. Particular care has been taken to obtain complete drill intersections of the orebody and to maximize wet sample recoveries. Extensive re-sampling and re-analysis of samples has confirmed that Bottle Creek is unusual for an oxidized gold deposit in that all the gold appears to be very fine grained, and evenly distributed within the mineralized zone.

Jan 1, 1987

By R. I. Grauch, Michael D. Glascock, Chen Nansheng, Jr Coveney, James B. Murowchick

"Unusually rich molybdenum ores (cutoff grade = 4.10/0 Mo) hosted by Lower Cambrian black shales have been mined since 1985 near Zunyi in the province of Guizhou in China. Similar ores were once worked for Mo and Ni near Dayong in the province of Hunan. In both mining areas, mineralization occurs in Lower Cambrian black shale (Niutitang Formation and stratigraphic equivalents) as a single sulfide bed or lens with exposed thicknesses up to 15 cm and reported thicknesses up to 35 cm. In addition to high Mo values (4% to 7%), ore samples contain up to 7% Ni, 2% Zn, 2.5% As, and several hundred ppb Au and Pt-group elements, but the precious metals have never been recovered from the ores. Sporadic occurrences of Mo-Ni sulfide ore beds are found in at least five provinces stretching approximately 1600 Ian from Yunnan to Zhejiang. None of the Mo-Ni ore-bed occurrences has any obvious connection with mafic or ultramafic source rocks. Similar occurrences containing elevated values for Ni, Mo, and PGE exist in Devonian black shale in the Yukon. Future exploration for Pt, Au, Mo, and Ni deposits should consider this previously unknown type of sediment-hosted mineral deposit.Sommaire - Des minerais anormalement riches en molybdène (teneur-limite = 4.1% Mo) provenant de schistes argileux noirs du Cambrien Inferieur ont été exploites depuis 1985 près de Zunyi dans la province de Guizhou en Chine. Des minerais semblables ont déjà été traire pour Mo et Ni près de Dayong dans la province de Hunan. Dans ces deux régions minières, la minéralisation se présente dans le schiste argileux noir du Cambrien Inferieur (Formation Niutitang et équivalents stratigraphiques) sous forme de couche ou lentille unique de sulfures avec des épaisseurs exposées de plus de 15 cm et des épaisseurs rapport6es de plus de 35 cm. En plus des fortes teneurs en Mo (4%-7%), des échantillons du minerai contiennent jusqu’ à 7% de Ni, 2% de Zn, 2.5% d&apos;As, et plusieurs centaines de ppb d&apos;or et d&apos;éléments du groupe du platine; toutefois, les métaux précieux n&apos;ont jamais été récupérés des minerais. Des présences sporadiques sous forme de couches de minerai sulfure de Mo-Ni se retrouvent dans pas moins de cinq provinces s&apos;etendant sur 1600 km de Yunnan a Zhijiang. Aucune de ces présences de minerais, sous forme de couches, ne semble associée a des roches du type mafique ou ultramafique. Des présences similaires contenant des teneurs élevées en Ni, Mo et EOP se retrouvent dans le schiste argileux noir Devonien du Yukon. L&apos;exploration future pour des gisements de Pt, Au, Mo et Ni doit prendre en considération ce type de gisement encore inconnu précédemment."

Jan 1, 1992

NEARLY one hundred members of the Mining and Metallurgical Society of America and friends of Professor Peele met at dinner at the Aldine Club, New York, on the evening of April 26, to take part in the ceremonies attending the presentation of the Society&apos;s annual gold medal. This had been awarded to Professor Peele by the Society in recognition of his laborious and painstaking work as Editor-in-chief of the monu-mental "Mining Engi-neers&apos; Handbook. Carl A. Meissner acted as toastmaster. W. Y. Westervelt, a student and lifelong asso-ciate of Professor Peele, then recounted some of his friend&apos;s early exploits, be-ginning with his mining adventures in the paternal cellar, whereby the neces-sity for adequate ventilation was indelibly impressed on his mind. Graduating from the Columbia School of Mines in 1883, Robert Peele for several years followed the typical mining career, as assayer and superinten-dentatan outlying Colorado mine; mill foreman and assistant superintendent of the Silver King, in Ari-zona; in charge of a mine at Fairplay, Colo.; and superintendent for the Ore-gon Gold Mines Co., at Cornucopia. At intervals during this experience, he spent parts of four years on two mineral investigations m in Peru, Bolivia, Colombia, and Dutch Guiana. He i was called to Columbia as Adjunct Professor of Mining in 1892, and became Professor in 1904. During his sabattical leave in 1903 he travelled around the world, r stopping at some of the most important mining cen-ters, and in 1910 he renewed his acquaintance with South Africa and South America.

Jan 6, 1923

By Y. Luo

This paper presents a number of mathematical models for predicting the different phases of the complete surface subsidence process associated with underground longwall mining. A computer program developed based on the mathematical models is briefly introduced.

Jan 1, 1992

By A. P. Cohen, D. W. Fuerstenau

Methods of accounting for the feed size in analyzing the size distribution shift during comminution have been discussed in a number of papers.1,2,3 Based on experiments which charles2 performed with single Pyrex specimens, Schuhmann4 pointed out that the size modulus of an assembly of particles should be determined by the energy expended per unit volume (or mass), independent of the size of particle being comminuted. In this same paper, Schuhmann derived the Charles energy-size reduction relationship by considering that complex comminution operations can be considered to be the summation of many individual comminution events, each of which must be governed by Were 6wi is the mass of a particle receiving the impact, 6Ei is the energy delivered to the particle, ki is the size modulus of the product resulting from the impact, a is the distribution modulus of the assembly of particles, and A is a constant. Recent experiments on the compression loading of Pyrex spheres ranging in size from 1/8 to l-in. diam have shown that the size modulus of the fragments is determined by the strain energy at fracture per unit mass, independent of sphere diameter.&apos; The objective of the present investigation has been to determine experimentally whether the size distribution of the product from such a complex comminution process as rod milling is determined only by the energy expended per unit mass independent of feed size. Samples of each Tyler sieve fraction ranging from 4x6 to 48x65 mesh were prepared from crushed Brazilian quartz crystals. One kilogram of each fraction was ground at 60 pct solids in an 8x9 1/4-in. mill containing 17.5 kg of rods (26 rods, 5/8-in.; 10 rods, 3/4-in.; and 5 rods, 7/8-in. diam). In each test, the mill was run at 77 rpm for 15 min. Size distributions were determined by a wet-dry sieving technique. Table I presents the size distribution of the products obtained by grinding each of the size fractions. Because the size distributions are so nearly alike, they are plotted in Fig. 1 by shifting each size distribution for the different feed sizes one screen fraction to the right. Thus, the lowest point in each size distribution represents 400 mesh and each of the other sieve sizes must be shifted accordingly. A single regression line was calculated by combining the data for the six tests, excluding the coarsest feed and the two finest feed fractions. 6 This regression line, which is given by (Y \0.88 where y is the cumulative percentage of material

Jan 1, 1962