Search Documents

By M. H. Kline

Round Mountain is one of a number of locations investigated by the Bureau of Mines in its search for manganese deposits during the early phases at the strategic minerals program. The Suiter mine, on Round Mountain, had provided some 5,000 tons of manganese concentrates during the period 1917 to 1919, and early in 1941 prospecting by the Virginia Hardwood Lumber Co. in this same area had discovered manganese on what later became known as the Hall Pit. These promising indications encouraged the Bureau to begin an exploration project in search of additional reserves of manganese on Round Mountain in January 1942 (fig. 1).

Jan 1, 1948

By James C. Ray

DURING the summer of 1931, I spent four months in a study of the Willow Creek district, Alaska. This work was part of a general investigation of the territory contiguous to the route of the Government- owned Alaska Railroad. It was conducted by the U. S. Geological Survey to determine the real and potential merits of the mineral deposits, to stimulate development of them, and thus to increase the traffic on the Alaska Railroad.

Jan 1, 1932

By SUHAINA ISMAIL, NORLIA BAHARUN, SHAIK ABDUL RAHMAN, WAN NUR SYAFIQAH ANUAR, MOHAMMAD REZAEI ARDANI

Hypochlorite leaching system is a strong oxidizing solution for metal sulfides, which are naturally associated with gold extraction. This study evaluated the hypochlorite leaching of refractory gold ore by using the response surface method–central composite design (RSM-CCD) as a statistical approach in determining the optimum condition of gold extraction from refractory gold ore. The studied parameters for the gold recovery were pH (4 to 6), concentrations of Ca(OCl)2 (0.5 to 1.5 M) and NaCl (2.5 to 3.5 M) in the solution. It was found that the maximum gold extraction of 82.46% (13.85 g/t) was achieved at a pH of 4.0 with NaCl and Ca(OCl)2 concentrations of 2.93 M and 1.08 M, respectively. The statistical analysis also revealed that the amount of gold recovery in chloride solution was significantly depended on pH as the main factor, followed by concentrations of Ca(OCl)2 and NaCl.

Jan 8, 2021

By Longworth C. R

Competing requirements for land usage sometimes make the correct all- ocation difficult. The decision can be complicated by many factors such as local resident pressure, previous government decisions, economic pres- sures and the duration or permanency of the competing land usages. This problem often confronts the extractive industries with consequent delays in granting leases and some- times considerable local dissension. A proposal to extend the high grade silica sand quarry of the Wamberal Sand Company Pty. Limited is a microcosm of these competing requirements. The sand quarry is located on the New South Wales central coast. It is an open pit operation on a near beach deposit of silica sand suitable for flint glass manufacture.

Jan 1, 1976

By D. R. Pyke, R. S. Middleton

"Three main types of base metal sulphide mineralization are present in the Timmins area:(1) -Massive and stringer-type copper-zinc deposits occurring mainly in pyroclastic rocks, as typified by the mines of Kam-Kotia, Jameland and Canadian Jamieson, or within or close to possible breccia pipes as shown by the Genex and Kidd Creek mines. With the exception of the Kidd Creek mine, all of these orebodies occur northwest of Timmins (Kamiskotia area) and appear to lie within or close to a major center of volcanic activity characterized by a thick accumulation of felsic pyroclastic rocks and subordinate epizonal intrusions. The margins of the rhyolitic pile are interfingered with mafic volcanics; overlying sedi-ments mark the termination of a vol-canic cycle. The copper-zinc deposits in the Kamiskotia area are confined to a particular stratigraphic unit. Ore-bearing solutions were probably derived from the intrusive complex of the volcanic pile.(2) -Porphyry copper deposit of the Mcintyre mine. The deposit occurs in a quarz porphyry intrusion related to the volcanism in the area (Hurst, 1936). Mineralization was probably introduced at the time of intrusion, and subsequently redistributed within the porphyry during deformation. (3) -Massive and disseminated nickel mineralization, associated with serpentinized alpine-type ultramafic intrusions, as shown by the Alexo, McWatters, Hart, Inco and Texmont deposits. The nickel mineralization occurs at or near contacts of the serpentinites with felsic or mafic volcanics, or sulphide-bearing iron formations. The nickel deposits south of Timmins are confined to a particular stratigraphic unit along the margins of domical-shaped structures which appear to outline former volcanic centers. Sulphurization as pro-posed by Naldrett (1966) appears to be a workable hypothesis for the formation of some of the deposits."

Jan 1, 1971

By Jurgen Weissflog

Why, where and since when using shiftable conveyors? Advantages of this equipment The ever increasing demand for bulk materials such as ore, coal, lignite, oilsand, oilshale and bauxite requires mainly an opencast operation. To exploit these materials huge amounts of overburden and partings must be transportes by means of conveyors, trucks or trains. When analyzing the various opencast mines it can be established that there exist only two basic types of mining systems, i. e., the discontinuous strip mining system as used in the USA (Fig. 1) and the continuous mining system as is commonly applied in Europe. The reason why these two mining methods have been developed parallel to and independently of each other to such a high technical standard results from the varying geological conditions of the mineral deposits.

Jan 1, 1983

By S. J. Gerdemann

In support of its objective to improve mine safety, the Bureau of Mines has searched for better materials and systems to anchor roof bolts. TIlis report describes a study on the effects of mine waters upon accelerated gypsum, one of the materials under consideration. The accelerated gypsuw dissolved at an appreciable rate relative to an assumed 10-yr life span of a roof bolt. Surface orientation, initial ion concentration of a dissolving solution, and flow rate of the solu-tion had substantial effects on the dissolution rate. Factors such as water-cement ratio, accelerator content, wax capsule additions to the gypsum in cartridge-installed bolts, surface area, temperature, and curing duration had little effect. In an actual roof-bolt environment, dissolution will occur in static solutions to the solubility limit of gypsum (~2 giL) and cease, result-ing in minimal damage; but in flows of unsaturated solution as slow as 1 L per month, a loss of up to 10 pct will occur in 2 yr. Since miners cannot readily measure the flow or ion concentration of static-appearing water at every roof-bolt site, all such water must be assumed to be pure and flowing. It is recommended that gypsum-bonded roof bolts be confined to dry roofs only.

Jan 1, 1983

By J. P. Gouvea

Back-analysis of two mining-induced tremors in 2011 was used to determine a modelling criterion for the entire Klerksdorp Goldfield (i.e., Vaal Reefs region). At that time, most mining operations in the region were owned by AngloGold Ashanti (AGA) and shared many geotechnical similarities. By 2018 AGA had sold off all its Klerksdorp operations to different mining companies, which continued applying the 2011 modelling criterion. As mining activities became more remote, scattered, and isolated, the extraction of isolated blocks of ground and remnants became increasingly necessary. However, the inherited criterion allowed only minimal or no mining activities at these areas. Keeping in mind that safety is the overriding consideration, an innovative numerical modelling approach, which includes the application of peak particle velocity designs, was developed to provide practitioners in the Klerksdorp Goldfield with a suitable criterion to justifiably and safely mine isolated blocks of ground and remnants. This would not always be possible if a conformist approach was used.

Mar 14, 2024

By Levente Becze

The zinc bottom dross is obtained as a by-product from hot dip galvanizing operations and contains at least 92 % zinc, which is recycled mainly by pyrometallurgical processes. The overall costs of such a treatment, however, are often relatively high, and the very strict environmental protection regulations might also cause additional difficulties for the high temperature procedures in the future. Therefore, a novel hydro-electrometallurgical process has been developed in our laboratory, by which one can reclaim zinc of high purity, while attempting to achieve low energy consumption and making allowances for all the environmental restrictions. This aqueous processing technique, based on electrolytic refining in a cell equipped with anion-exchange membrane to separate the anode and cathode compartments, allows the indirect purification of the anolyte. Zinc is dissolved from the anode along with some of the impurity elements, while the intermetallic compounds (Fe-Zn, Fe-AI- Zn) are accumulated in the anode slime.

Jan 1, 2003

By L. B. Phelps

The nation is confronted with thousands of acres of abandoned coal lands. In Pennsylvania alone, these lands have been estimated to cost $15 billion to reclaim (Pennsylvania Bulletin, 1985). One way to deal with this problem is to provide a mechanism by which the active mining industry can undertake to remine certain of these abandoned mine areas. Remining is classified as reaffecting previously mined areas in order td extract the remaining coal reserves while improving the environmental quality of these lands through land restogation and abatement of pollutional discharges. However, there currently is a disincentive for operators to plan to extract reserves on these abandoned mine lands which have preexisting pollutional discharges. Therefore, they presently avoid them. This is because of the "potentially unlimited liability of post- mining treatment for any discharges that would remain after mining? (Pennsylvania Bulletin, 1985).

Jan 1, 1987

By Sastry Putcha, Santosh Mummaneni, Swamy Avasarala, Vamshi Vemula

"This paper presents the results from a case study on the comparison of two strain acquisition instrumentation technologies, Geokon rebar strainmeters and Embedded Data Collectors (EDC) for the DC Water Main Pump Station project, in Washington D.C. These two instrumentation systems were installed by AVER in a single 18-inch (0.45 m) diameter augercast pile (with one-1.25 inch (3.175 cm) dywidag bar) at critical locations to determine the load transfer mechanism and establish a comparison between strain/load measured with these two systems along the pile. A quick static load test was performed on the test pile as per ASTM D1143 standard.Prior to the installation of the pile, a 24-inch (0.6 m) diameter outer casing was installed to the proposed cutoff elevation of -22.5 feet (-6.85 m) to discount the frictional resitance within the upper overburden zone. The pile was then drilled through the outer casing to the tip elevation of -65.02 feet (-19.8 m) with inner casing within the overburden zone. Strainmeters along with EDC were installed on dywidag bar at various locations and then wet set into the concrete following auger retrieval. The loads measured with EDC and Geokon sensors were within 15% percent of each other.PROJECT BACKGROUNDProject Background & Requirements:Like any other foundation piles, augercast piles are extensively used in the public and private sector structures in the United States for many years. It is a common practice to perform static compression (ASTM D1143), tension (ASTM D3689), and lateral load tests (ASTM D3966) depending on the project requirements. In recent years, embedded strain sensors, manufactured by Smart Structures, USA has gained prominence for its use to collect both static and dynamic measurements for driven piles. In addition, AVER has successfully used EDC for collecting long term static measurements for an abutment drilled shafts for I-95 Hotlanes project in Virginia, USA.Geokon sisterbar strain gages are widely used in the foundation industry to monitor the load transfer mechanism within pile foundations throughout the world. As the Geokon strainmeters are vibrating wire and are welded to a sister bar, there is often a debate within the engineering community with regards to what modulus to use when converting measured strains to loads. EDC sensors, unlike Geokon strain gages are embedded directly into the concrete and therefore do not have the same concern."

Jan 1, 1900

By J. Ostwald, L. T. Matthews, C. E. Loo

Australia has large reserves of pisolitic limonite. Mining recently commenced on the Yandicoogina deposit to produce a high-grade sintering ore. The ore contains about 10 wt% combined water and simulated sintering temperature profiles indicate that progressive dehydration of ore particles occurs in the temperature range 300-700 degrees C. Studies by optical microscopy show that although the dehyrdrated ore particles contain numerous cracks, there is no change in the microstructure of the ore because topotactic transformation to haematite results in the formation of compact masses of very fine-grained haematite microcrysts. When the ore is held at around 1 200 degrees C for 1 min significant recrystallisation of these microcrysts occurs, resulting in the formation of optically visible, micrometre sized haematite crystallites. Studies to simulate the behaviour of ore particles during sintering (as nuclear particles surrounded by a standard adhering fines mixture) show that the recrystallisation process occurs much earlier at temperatures of about 900 degrees C. Further studies indicate that CaO in the adhering fines mixture enhances the recrystallisation of the ore nuclei. The results of the investigation indicate that the pseudo-relict haematite in sinters produced from ore blends that contain significant levels of pisolitic limonite consists of dehydrated goethite that has undergone significant recrystallisation and grain growth, a phenomenon that is facilitated by the presence of lime derived from the sintering melt.

Jan 12, 1992

By W. E. Brown, P. R. Porath, V. Miller, C. E. Wood, C. Prasky, E. P. Barrett

"INTRODUCTION This investigation was a part at the Bureau of Mines program for the production of critical and essential materials needed for the war.The Boykin Committee for investigating the steel shortage aided in obtaining an appropriation to be expended by the Bureau of Mines in studying the utilization of North Dakota lignite in the manufacture of hydrogen that could be used in the production of sponge iron from low grade ores of Minnesota.OBJECT OF INVESTIGATIONThe investigation was conducted by the Bureau of Mines to ""determine the workability of the proposed bubble-hearth process and its possible use in connection with an experimental plant for the gasification of lignite being operated by the Coal Division of the Bureau of Mines at Grand Forks, North Dakota.ACKNOWLEDGMENTSThis report is one of many on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources.Investigations of our mineral resources are conducted by the Mining Branch, L. B. Moon, chief, and by the Metallurgical Branch, O. C. Ralston, chief.The scope of the report falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficulty beneficiated ores, the production of pure metals from domestic deposits, the exploration of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice."

Jun 1, 1947

By E. W. Sawyer

Gelling-grade attapulgite and sepiolite clays are employed as thickening agents for the preparation of ionically contaminated drilling fluids where the use of fresh water clays are unfeasible or impossible. Attapulgite and sepiolite are nonswelling clays that can be dispersed and reflocculated by mechanical and chemical means to increase the viscosity of fresh water, salt containing waters, gypsum contaminated waters and fluids containing cement. Such gelled systems are quite stable in viscosity properties and can be further treated with other necessary additives such as thinners, water loss reducers, weighting agents, surfactants, etc. Many of the oil well drilling fluid practices have influenced such technologies as water well drilling, foundation drilling and waste disposal. The use of salt water gelling clays in these fields will be described and compared to oil well drilling.

Jan 1, 1986

By S. Vardy

The paper notes that the extraction of 22% of the remaining workable reserves in the north western area involves a risk of spontaneous combustion higher than is normal in Britain. Mining systems have been tailor made in order to minimize the risk of spontaneous heatings, and these systems are described. Well-proved methods of combating spontaneous combustion are referred to, as well as the limitations which now apply to them as the result of the introduction of modern mining techniques. A substantial part of the paper is devoted to the circumstances in which spontaneous combustion occurs underground in the north western area. Several actual incidents which have occurred in the last few years, along with the practical application of the lessons learned, are described. Of particular note are: a) the procedure adopted in the north western area to equalize pressure differences across stoppings using pressure chambers, and b) a retreat mining system, primarily designed to deal with high methane emission and steep gradients, which also affords some protection against spontaneous combustion.

May 23, 1905

By W. M. Dressel

A simple, reliable field test for beryllium in rocks has been developed by the Rolla Metallurgy Research Center of the Federal Bureau of Minas. A small portion of the pulverized rock is fused with a sodium carbonate-sodium hydroxide flux in a wire loop. The fused mass is dissolved in water, a few drops of quinizarin solution are added, and the solution is viewed under ultraviolet light. A pink-to-orange fluorescence reveals the presence of beryllium in a sample containing as little as 0.013 percent beryllium (0.26 percent beryl). INTRODUCTION New and potential uses for beryllium make necessary a more intensive search for this metal, which is so similar to aluminum in its chemical reactions that it is not separated from aluminum in ordinary chemical analyses. The principal ore mineral of beryllium is beryl, a beryllium-aluminum silicate, which contains only 5 percent beryllium. This mineral is so similar to quartz in appearance that it is not always possible to distinguish one from the other in the field. While the distinction may be made easily with a petrographic microscope, few prospectors have access to such an instrument, and fewer still know how to use it.

Jan 1, 1960

By AIME AIME

In the present number of Mining and Metallurgy, issued on the fiftieth anniversary of the founding of the Institute, it appears appropriate to chronicle a few of the interesting incidents respecting its early life. We are fortunate in being able to cull the following notes from unpublished manuscripts of Doctor Raymond and Doctor Drinker, than whom no other members could have written with greater exactness and fidelity. THE seventh decade of the 19th century may be said to have marked an. era in the history of the world. Industrially and .commercially it was marked by the wide application and utilization of discoveries already made, which came to their full effect at this period in steamships, railways, telegraph and cable lines; the standardization of parts in machines, from watches to locomotives; the use of 'dynamite, antiseptic surgery, the open-hearth steel process, the compressed-air rock-drill, the electric generator, and the Gatling gun. Through the opening of the Suez canal in 1870 the maritime trade of the world was revolutionized, sailing vessels were supplanted by steamers, while ocean cables and ocean "tramps" brought about far more rapid movement of commerce than had before been experienced. Politically, this period was marked by the sudden birth of the German empire and the beginning of that intensive internal development of the national resources of that empire in preparation for colonial extension and war, the amazing result of which has been made evident by the recent world conflict. In the United States, the significance of this decade was peculiarly important. The re-admission to the union of Virginia, Mississippi, Texas and Georgia in

Jan 1, 1921

By S. R. Droes

The U.S. Bureau of Mines investigated calcium fluoride (CaF2) assisted sulfuric acid (H2S04) leaching as an alternative to the melting-quenching procedure to obtain Mn from domestic manganese silicate resources. Pyroxmangite [(Mn, Fe) Si03] ore containing, in percent, 34.4 Mn, 22.8 Si, 2.6 Ca, and 1.3 Fe was leached in a 500-mL resin kettle. Ninety-six percent of the Mn was extracted under conditions of 330 g/L ore, 245 g/L H2S04, 35 g/L CaF2, 90' C, and 2 h. To incorporate electrowinning in recovering Mn, the ore was leached with a simulated spent anolyte solution containing, in grams per liter, 12 Mn, 140 H2S04, 130 (NH4)2S04 (ammonium sulfate), and 5 CaF2. Manganese extraction of 92 pct was achieved from 130 giL ore leached at 90° C in 3 h. The Fe, silica (SiOJ, and other impurities were precipitated from the pregnant solution by neutralization with ammonia (NH3). Manganese of greater than 99-pct purity was deposited at a cathode current density of 50 mA/ cm2 at 30° C, with a current efficiency of 65 pet in a two-compartment cell. A flowsheet was proposed for the leaching and electrowinning procedure.

Jan 1, 1990

By F. F. Netzeband

This report relates to the sulfur industry of seven States--Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas--and is part of a national study of the sulfur industry by the Bureau of Mines. Markets as used in this report are divided into two components for individual analysis-- (1) supplier markets which include regional Frasch and byproduct sulfur producers and (2) consumer markets which include processors and manufacturers requiring sulfur in their operations The term sulfur as used in this report includes brimstone, native sulfur, elemental sulfur, or sulfur equivalents.

Jan 1, 1964

By N. A. Warner, R. K. Manna

Physical modelling of liquid-phase oxygen mass transfer in a water model of part of a proposed new polymetallic smelter has been achieved. A study of solute mass transfer caused by multiple, subsonic air jets contacting superoxygenated water flowing in a channel model of the smelter converting hearth has been carried out. For a wide range of channel flow rates the rate of mass transfer was found to be independent of water velocity. The water model has been used to compare mass transfer for both open-packed and close-packed multiple-lance arrays with circular nozzles of diameters 2.26, 4.95, 10.95 and 24.40 mm. It was found that with fewer of the larger-diameter nozzles a reduction of up to 58% in liquid-phase mass transfer occurred, especially for the close-packed lance configurations. This restriction of liquid-phase mass transfer would result in reduced metal losses in the analogous smelting situation. The larger nozzles, however, exhibited more jet-jet and jet-channel wall interference effects than their smaller counterparts, resulting in an effective reduction in the momentum fluxes of the impinging jets

Jul 1, 1991