Search Documents

By Richard Peaker, Jens Lichter, Alexander V. Potapov

The recent combination of Computational Fluid Dynamics (CFD) and Discrete Element Modeling (DEM) can provide considerable insight into the performance of flotation cells. One area of interest from a fundamental equipment design perspective has been the influence of flotation cell size and the inflow rate on the metallurgical performance of the cell. One of the specific design objectives when increasing the size of flotation cells, or increasing the feed flow to the flotation cell, is to ensure that the feed stream flowing into the cell does not have an opportunity to bypass the mechanism. This paper describes the initial modeling efforts to quantify the inter-relationship of cell size, inflow rates, and feed and discharge box placement, on the retention time distribution of solids in the flotation cell, and the fraction of particles that bypass the mechanism on a size by size basis.

Jan 1, 2007

By María Eugenia Castro, Silvia Galasso, Jorge Duca, Claudia Osuna, Ernesto Esparza

"We present a procedure for treatment of non-active solutions equivalent to the solutions obtained from dissolution of ionic exchange resins used in purification of a nuclear reactor primary cooling system containing Co, Ni, Cs and its isotropic varieties as main radioactivity source. Finally it is immobilized into a ferritic matrix by calcination which avoids its future leaching into environment.In order to achieve the objective of this treatment, a bivalent and a trivalent iron salt is added to the solution. Then, either a base or an acid is added, depending on the initial pH of the treated solution, with a Cs precipitating additive in order to reduce Co and Cs by precipitation, flocculation and adsorption. Controlling the amount of precipitating reactives it is possible to modify the activity/volume rate becoming a medium into a low radioactivity waste.The leaching test result applied over the ferritic sample is lower than the minimum limit established by law. Therefore, it can be kept safely in a interim storage."

Jan 1, 2008

By Bernard H. Hertlein

All methods of deep foundation construction present challenges to the contractor and engineer that vary according to the method employed, and the geotechnical conditions in which it is being used. Augered-Cast-In-Place (ACIP) piles are generally regarded as one of the most challenging, because the construction method precludes the use of traditional shaft inspection and quality control techniques. Application of Nondestructive Test (NDT) methods can provide quality control for ACIP shafts that traditional methods cannot, but each NDT method has limitations. These make some NDT methods unsuitable for use on ACIP shafts, and may limit the effectiveness of others, depending on geotechnical conditions. To help contractors and engineers working with ACIP piles select the test method most appropriate to specific site conditions, this paper presents a summary of the major NDT methods currently available, and reviews their capabilities with respect to the unique conditions presented by ACIP pile construction. Case histories illustrate how a combination of careful method selection, skilled data interpretation, and experienced engineering judgment have resolved problems and ensured quality in foundation construction by discriminating between potentially serious defects, and those that are unlikely to be significant.

Jan 1, 1997

By David R. Jessey

This volume contains the detailed mine site reports written by the WAPORA, Inc. and KETRON, Inc. staffs. It is a companion Appendix Volume to Control of Water Pollution from Surface Mining Operations. Copies of this report are maintained on Open File at the U.S. Bureau of Mines Research Center, Spokane, Washington.

Jan 1, 1981

By B. Lueger, D. Shen, M. Sedighy, R. Rand, R. Saleh, J. Cheung, M. Rifai, I. Khan, W. Sauri, D. Setianto

The world’s first active power demand stabilization system for a 3-electrode electric arc smelting furnace was commissioned at PT Vale Indonesia in December 2012 on Furnace No. 2 using an SPLC (Smart Predictive Line Controller). The SPLC technology in combination with the Furnace No. 2 rebuild and other upgrades has enabled PT Vale to increase the electrical input to the furnace by up to 20% on a stable and sustainable basis by eliminating peak powers that overload and trip out the electrical equipment, and by reducing power unbalances. The SPLC technology maintains smooth arc power using a continuously variable thyristor controlled series reactor. The SPLC compensates variations in the furnace arc with predictive changes in the circuit reactance at a speed of up to 60 times a second. The system started up quickly and has been shown to be easy to operate and maintain by PT Vale. PT Vale’s Operations Team has been testing the new system at set points of up to 90 MW on the newly re-built Furnace No. 2. Over the last 12 months, the throughput of Line 2 has increased by approximately 10% on an annual average; however, debottlenecking in other design areas of the operation is required in order to achieve 90MW operation on a sustainable basis. This outstanding success results from a combination of the furnace and other upgrades, the SPLC active power stabilization, and the skill of PT Vale in quickly adopting new technologies and maximizing the combined benefits of each technology in their operation.

Jan 1, 2014

By W. D. Monaghan

Flame cutting and welding is one of the major causes of fires and explosions in underground U.S. coal mines. On May 20, 2006, a flame cutting operation at the Darby Mine No. 1 led to an explosion that resulted in five fatalities. On January 22, 2003, another explosion caused by flame cutting at the McElroy Mine resulted in three fatalities and three serious injuries. On June 22, 1999, a flame cutting and welding operation at the Loveridge Mine caused a fire that resulted in sealing of the mine for an extended period. Finally, on March 19, 1992, an explosion at the Blacksville No. 1 Mine that was caused by welding resulted in four fatalities. The National Institute for Occupational Safety and Health (NIOSH) conducted a study on fires and explosions in underground U.S. coal mines that were caused by flame cutting and welding operations to determine the root causes of these types of fires and explosions. The methodology included interviewing mining personnel who perform flame cutting or welding operations in underground U.S. coal mines and visiting mines to observe these operations, and MSHA reports of investigations and accidents statistics were analyzed. The results were used to identify and compare differences between flame cutting and welding practices and techniques in small and large mines, Eastern and Western mines, low seam and high seam mines, room and pillar and longwall mines, and between experienced miners and new miners. As a result of this study, best practices and interventions were developed to reduce the number of fires and explosions caused by flame cutting and welding. This paper provides a summary of this work. Disclaimer: The finding and conclusion in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupation Safety and Health.

Jan 1, 2009

By F. V. Meriwether

The Bureau of Mines, in cooperation with the Federal, State, and local health services, and the mining companies, and miners? organizations, has for several years been carrying on sanitary surveys of mining districts in various states, with the purpose of collecting information on good and poor practices in mine sanitation, construction of approved wash-houses and change houses, the measures being taken to combat preventable diseases, the essential features of good houses for mining towns, and other conditions affecting the health and efficiency of miners and their families. The knowledge thus gained is disseminated for the common benefit of the mining industry. The sanitary conditions in the coal-mining districts of Alabama, as found by a recent survey made by the writer, are presented in this report. In addition to the towns on which this report is chiefly based, at least twice as many were visited where no details :were taken, but their general conditions are taken into consideration in summing conditions in the coal districts.

Jan 1, 1926

By V. D. del Valle, T. G. Joseph, J. J. Berezan

Aggressive driving patterns, rough and poorly maintained roads and pit floors, along with the occasional bump and poorly placed load from a shovel can create intense and sometimes serious vibration levels on a heavy hauler. The effects of high vibration have been shown to be of concern for the health of the operator as well as the reliability of the equipment. It is proposed that an onboard vibration warning system based on the ISO 2631-1 standard could be used to help operators reduce the vibration levels experienced in a heavy hauler. The onboard system would consist of a screen that displays the instantaneous vibration in the form of three lights: green (safe zone), yellow (cautious zone), and red (danger zone), as well as an overall vibration exposure or dose for the entire shift. With the utilization of the warning system, it is anticipated that the overall vibration levels will be decreased resulting in improved operator health, a reduction of vibration-induced maintenance, and improved haul roads through reduced impact loading and repair for localized trouble areas.

Jan 1, 2004

By L. G. Stolarczyk, Y. Luo, S. S. Peng

Detection and assessment of severe geological anomalies ahead of a longwall face greatly benefits the mining operation. Electromagnetic-based Radio Imaging Method (RIM) is one of the most promising geophysical methods for this task. Based on two decades of development, the latest RIM instrumentation (RIM-IV) has expanded its operational range up to 1,800ft.A site demonstration of the RIM-IV technology was recently conducted within a longwall panel. An extensive ground truth study was performed to evaluate the accuracy of the RIM survey results. This study compared the generated RIM tomograms of attenuation rate with the mapped geological anomalies. Three different approaches have been employed to examine the accuracy of the RIM results and to correlate the measured signal attenuation rates with physical properties of the coal seam. The study shows that the RIM-IV technology is able to identify and delineate those geological features that would severely affect the longwall mining operation.

Jan 1, 2004

By I. M. London, G. P. Hatch

The Canadian Rare Earth Elements Network (CREEN) was formally launched at the Rare Earth Symposium at The Metallurgy and Materials Society of CIM (MetSoc) Conference of Metallurgists in October 2013. CREEN is an industry-led, multi-stakeholder network focused on providing collaborative solutions that will advance Canada’s REE sector to produce a significant proportion of the global production of separated critical rare earth products by 2018. The Network is industry driven by companies with REE projects under development and supported by universities, engineering firms, national and commercial laboratories, and government. CREEN aims to accelerate the development and delivery of timely solutions to technical and economic issues specifically facing Canada’s emerging rare earth sector. It will facilitate partnerships with other national and international organizations to leverage existing research initiatives. It will also support training and education to ensure that the needed qualified human resources are available to achieve the sector’s goals. CREEN membership spans the full rare earth supply chain and technical support organizations, from prospective producers, advanced project developers, national and commercial laboratories, engineering consultants, university researchers, and other innovators. This paper provides an update on CREEN's developing networking and project develop

Jan 1, 2014

By K. Pirapakaran

The Geotechnical Engineering research group at James Cook University has been working closely with all the leading mines in Australia in the area of minefills. They have carried out substantial research and consulting work on the drainage and stress developments within hydraulic fills. The objective of this paper is to summarize their work during the past five years on hydraulic fills. The paper will serve as a one-stop reference, pointing to relevant literature including the authors? own publications, on various issues covering drainage and stress developments within hydraulic fills. More than 15 different hydraulic fills, representing five major mines in Australia, were studied. Their grain size distributions and placement characteristics including permeability, porosity and dry density were studied and comparisons were made with the limited in situ data available in the literature. Stress development within hydraulic fills has been studied to minimize the risk associated with barricades failure. FLAC and FLAC3D were used to model stress developments within the hydraulic fills and were compared against the approximate closed form solutions available in the literature. A laboratory model was developed to study arching effects within the hydraulic fills.

May 1, 2007

By B. T. Brady

Recent theoretical, experimental, and field studies conducted by the Bureau of Mines suggest that rock failures may be predicted and, in some instances, controlled. Theoretical studies that were later corroborated by laboratory and field studies predict that a seismic anomaly will precede rock bursts and/or roof falls in mines. The seismic anomaly is predicted to consist of an increase in the number of seismic events occurring in the immediate vicinity where the failure 1s nucleated. This increase will then be followed by a dramatic decrease of seismicity in a broad region that surrounds the location of the impending failure. The dimensions of this region allow a preliminary estimate of the time to failure (measured from the time the seismicity increase began) as well as an estimate of the energy that will be released at the instant of failure. Field observations indicating that this predicted behavior does precede rock bursts and a roof fall are presented in this report. Implications of results to the problem of failure control in mines that experience massive rock failures are discussed.

Jan 1, 1978

By AIME AIME

L H. DUSCHAK gave an interesting talk at a recent meeting of the. San Francisco Section, based -011 experimental work with a variety of ores at the laborator of the Treadwell-Yukon Co., in Berkeley, Cal. He was of the opinion that the customary "cut and try" method of flotation testing was still in evidence and that the flotation process was more of an art than an exact science. Propounded theories have enabled investigators to' classify reagents as well as to suggest new ideas both in the metallic and nonmetallic fields, but the application of theory has riot as yet been able to solve many of the unknown factors in operation.

Jan 1, 1932

By Manish Uttarwar, Rajendra Yerpude

India is the third largest producer of coal and the fourth largest in terms of coal reserves in the world. However, new research quite ironically projects that despite the continuing growth in domestic coal production, the country’s exploding economic growth will position it to be the biggest coal importer by 2020. India’s inability to meet the domestic coal demand is mainly attributed to low rate of production, increasing stripping ratio, non use of appropriate technology etc. of coal mining operations here. Presently Indian surface mines which have to shoulder the onerous responsibility of augmenting the coal extraction rate at an even brisker pace are mulling bigger, better and more efficient operations ensuring commensurate rise in stripping work as well. This mammoth task can be accomplished only by deploying smart technologies. In this perspective, cast blasting of overburden emerges on the horizon as a promising alternative for enhancement of the production and productivity of Indian open-pit coal mines.

Jan 1, 2009

By T. J. Serenko

The epithermal deposit is hosted by Tertiary volcanic rocks that lie between mid-Miocene normal faults of the Northern Nevada Rift. Petrographic, laser-ablation and metallurgical observations suggested that the gold occurs in two principal forms: native (and electrum) and disseminated in arsenopyrite. It was proposed that gold is distributed between two parageneses with distinct mineralogical associations. Detailed downhole geochemical study supported the observations. Concentrations of Au, Ag, As, Sb and Se were determined from drill core and reverse-circulation cutting composites and contoured on cross-sections. Gold was indeed shown to have a bimodal distribution with the two parts separated spatially and perhaps temporally, implying that two separate genetic processes acted to concentrate gold at Mule Canyon

Aug 1, 1995

By O. Llewellyn Jack

From September 1978 to December 1983, ESD Corporation (formerly a Division of FMC Corporation) undertook the development and testing of a bidirectional auger under contract with the U.S. Department of Energy. Underground testing began in August 1981 at Peabody Coal Company's Marissa Mine near Marissa, Illinois. The auger was developed to increase mine production and coal recovery without increasing land subsidence. It bored 4-foot-diameter by 10-foot-deep holes into pillars on 7-foot centers (each hole recovering 5 tons). All operating during this test was performed by maintenance personnel with the goal of finding ways to increase the machine potential. The maximum excavation rate achieved was 1.4 tons per minute. It was concluded that the concept of drilling short holes to extract coal from underground pillars without surface subsidence was practicable with a wheel mounted auger, but that more power was desirable for this mine, and that the hydraulically driven augering system that provided experimental versatility was not sufficiently reliable for production use.

Jan 1, 1983

By R. H. O. Wagner

"This paper describes the bench testing, pilot plant studies of alternative flowsheets, to determine the feasibility of gold recovery, by carbon in pulp extraction, in the Schumacher Mill gold flotation tailings. The economics were calculated based on pilot plant recoveries and actual industry operating costs.The economics of the carbon in pulp treatment of the gold flotation tailings were not justifiable. The economics of desliming the gold flotation tailings followed by carbon in pulp treatment were marginal, but favourable. INTRODUCTIONPamour Porcupine Mines, Limited is a gold, silver and copper producer located in Timmins, Ontario. In 1983 the head grade of Pamour's gold ores averaged nine one hundredths of a troy ounce of gold per short ton.Pamour operates two area mills to concentrate the gold ores. Free milling gold ores are processed at the Pamour One Mine mill, whereas the refractory carbonaceous gold ores, and complex gold, silver, and copper sulphide ores, are processed through the Schumacher Mine mill.The complex Schumacher mill feed ores do not all react favourably to flotation methods, consequently this study was commissioned to investigate the feasibility of the carbon in pulp cyanidation of the Schumacher mill gold flotation tailings. These tailings contain ten to fifteen percent of the gold in the mill feed. During the study period, the average grade of the Schumacher mill flotation tailings was nine one thousandths of a troy ounce of gold per ton, or one quarter of a gram of gold per metric tonne."

Jan 1, 1984

By Norman O. Lotter, Virginia Lawson, Mika Muinonen, Dominic Fragomeni, Jorge F. Oliveira

Development of metallurgical flowsheets from drill core to production of finished metal involves two main domains: process mineralogy to sample the ore and develop a successful flowsheet producing saleable concentrate; and extractive metallurgy to convert that saleable concentrate to finished metal. Effective flowsheet development for a new or brown-field concentrator and processing facility is essential to project schedule and return on investment. Over the last decade in particular, the integration of geology, mineralogy, sampling, and mineral processing have empowered the development of an improved practice in flowsheet development. The use of geometallurgical units as a basis for best-practice sampling delivers representative study material to the laboratory. Modern automated mineralogy characterises the whole rock assembly and paymetal mineral hosting, to address downstream process implications. Batch scale flotation testing then uses this information to design and perform well-focused strategies. At early stages of the project, the Extractive Metallurgy team is engaged to determine processing constraints or other economic drivers in conversion of the saleable concentrate into finished metal. The team evaluates available technologies, assesses the impurities and key properties of the given concentrate. In many cases, changes to mineral processing flowsheet are required to maximize value per tonne of concentrate. Site conditions, availability of infrastructure, energy and power all play an important role. Modern metallurgical simulation tools such as FactSage™ and METSIM™ can quickly define the appropriate test program for each process. Bench scale testing and appropriate scale of piloting can confirm simulations and provide design criteria. A case study demonstrates how effective use of these tools and a multidisciplinary team can accelerate flowsheet development, while reducing costs and ensuring that the designed processing facilities maximize project value with minimum risk.

Jan 1, 2014

By Nick Lewis

Farce Mining of Texas is a surface coal mine located in Laredo, Texas. Farce mines and sells approximately 600,000 tons /year of bituminous coal. A map showing the location of Laredo is provided in Figure 1. As shown, Laredo is located on the border between the United States and Mexico. The mine property runs to the Rio Grande River, the border between the two countries. Farce pumps water from the Rio Grande for use in their coal preparation plant. Laredo’s climate is quite dry with annual rainfall averaging about 12” per year. Also, due to the southern location, Laredo is quite hot. It is common for the temperature to reach 100” F in March and maintain these temperatures through September.

Jan 1, 1994

By G. Tiess, S. Mujiyanto

Indonesia is a fast growing democratic developing country comprising more than 17,000 islands, founding member of ASEAN and a member of the G-20 major economies. It is one of the most highly mineralised countries in the world, the mining sector playing a pivotal role in the country's economy. In 2001, the Decentralization Law No. 22/1999 came into force and caused a transfer of authority and responsibility from central to regional and local administrative governments. The new Mining Law of 2009 substituted its 40 year old predecessor, but lacked detailed regulations for its implementation. These were only issued in 2010, which lead to a period of great uncertainty for investors in the mining industry. The new legislation intends to foster domestic economic development, which may be interpreted as protectionist policy. For the development of a sustainable mineral resources policy, further endeavours will have to be made.

Jan 1, 2011