Search Documents

By O. C. Rojas

Improvements and modifications on lay out and process, from 1997 till 1998, are presented. Based on a Teniente Converter, started up 1993, a Strategic Development Plan was structured to increase the production efficiency and comply with the enviromental regulations, too. It considered the oxygen supplies to the Teniente Converter and Peirce Smith converters; reverberatory furnace shut down as a smelting unit; and the Teniente converter slag treatment through a combined process between a Slag Settler furnace and flotation. Also it included the off-gas handling and treatment.

Jan 1, 1999

By Zenjiro Asaki

The copper concentrate particles dissolve quickly into the molten matte in the smelting furnace of Mitsubishi Process, which indicates that the sulfide smelting is essentially a gas/liquid reaction. In this paper, theoretical calculation has been made on the rate of oxidation of FeS component in the matte to form FeO by rising gas bubbles using the penetration theory. The results showed that all the oxygen in the bubble of 1.2 cm in diameter, which is the maximum stable diameter, is consumed in 3 ms. This time required is sufficiently short, and it results in the actual operation of smelting furnace of 1100% oxygen-efficiency. These calculations indicate that most smelting reactions are completed just under the lance, except slag formation.

Jan 1, 2002

By Takashi Nakamura, Kenji Oosumi, Kazuhisa Fujisawa, Takayuki Kogishi

"Recycling of used aluminum beverage cans(UBCs) is one of the important issues for aluminum manufacturer presently. The direct re-melting of UBCs shows two problems. One is a reduction in molten aluminum recovery and the other is a contamination of other metals such as Ti and Fe from paints. Both problems are caused by paints coated on the surfaces of aluminum cans. Removal technique of the paints, therefore, has been required. Although roasting and shot blast techniques have been developed, both were not successful in removing the paints effectively. A swell-peeling method has been applied to remove them using a methylene chloride solution with acids and it works very well. Small laboratory scale tests have been carried out to develop the commercial process and clarify the mechanism of the swell-peeling method in the present study.When the surface area of UBC is more than 10 cm2, peeling time is independent of the surface area, about 60 seconds, because swelling phenomenon is controlled by the penetration of the liquid through the fine pits on the surface of the paint. This is good for a commercial process. Peeling takes place when the swelling force generated by methylene chloride exceeds the adhesion force between the film and the surface of aluminum, that is weakened by the coexisting acid, especially halogenated acetic acid."

Jan 1, 2000

By Jakub Kaczorowski

In the production of Mn-alloys, the Boudouard reaction significantly influences the mass and energy balance. The endothermic nature of this reaction requires more energy for the process, while the direct consumption of carbon is reflected in the greater demand for carbonaceous raw materials. Therefore, it is desirable to eliminate or suppress the reaction. The kinetics of the Boudouard reaction are a function of many factors, of which coke properties and the conditions around the particles (i.e. temperature, gas composition) seem to be the most important. In the present study properties of selected single source and commercial metallurgical cokes are compared with reactivity results. The single source cokes represent a single coal that has been carbonized in a laboratory scale furnace. The commercial cokes are products of carbonization of coal blends under industrial conditions. The coke properties include proximate, ultimate and ash analysis. Also, coke petrography with carbon forms is included. The reactivity tests were performed on different particle sizes at various temperatures, gas compositions and gas flow rates. The experimental parameters were chosen to simulate the conditions in an industrial furnace. The results show that highly graphitized structure of cokes, minimal surface area and a low concentration of ash retard the reactivity. Of the other factors, the temperature and the gas composition have the greatest impact on the reactivity.

Jan 1, 2006

By John B. Dale

A primary objective of copper mining, smelting and refining operations is the cost- effective, efficient, and environmentally-acceptable control of the level of various metal ions throughout the processing and effluent treatment flowsheets. Effective ionic control maximizes product and by-product quality, allows for broad flexibility in sourcing impurity laden ores, minimizes capital and operating costs, and can achieve zero discharge operations. In order to meet increasingly stringent cost, environmental and product quality requirements, separation technologies are needed that can selectively remove and recover deleterious or valuable ions. Ideally, the subsequently obtained salts or metals can be recycled in the process, disposed of in an environmentally acceptable manner, or sold as valuable by-products. The use of MRT, a highly selective separations technology, has been demonstrated to be a cost effective, efficient, and environmentally- sound treatment for a wide range of cations and anions that are commonly found in copper electrorefining and electrowinning circuits, as well as in environmental treatment operations. These include heavy and transition metals, precious metals, halides and alkali/alkaline earths. This paper will review a number of areas of interest including: recovery and refining of platinum group metals from copper anode slimes, recovery of copper from acid mine drainage streams, extraction of Bi, Sb and C1 from copper electrorefining and electrowinning circuits.

Jan 1, 1999

By Z. S. Wronski

In rapidly solidified Fe-Nd-B permanent magnet alloys, the content and distribution of Nd-rich intermetallic and Fe-phases determine coercivity Hc and remanence Br. Consequently, microstructure plays a crucial role in deter- mining the (BH) max-product of permanent magnets fabricated from these alloys. A study has been initiated to investigate changes in microstructure and the effects on magnetic properties as the material is processed from arc-melted ingot to melt-spun flakes and finally to a product consolidated by hot-forming. Anisotropic magnetization behaviour has been observed in rapidly solidified flakes after low-temperature annealing.

Jan 1, 1989

By Romeo U. Pagador

After privatization in 1999, PASAR Corporation initiated a plant modernization program to optimize the performance of the smelter by increasing plant availability. This initiative required operational adjustments to the converting and anode furnace procedures, to support the higher throughput in the flash furnace, while continuing to meet government environmental regulations. The major shift in production direction was to eliminate the 30-35 day maintenance shutdown every two years, and replace it with a 15-day shutdown. This paper discusses the changes implemented in the converter and anode operation that have resulted in an increase of 10% in flash furnace throughput, an 18% increase in blister output, to 170 tonnes per cycle, and a converter campaign tonnage increase of 10%. Since privatization, PASAR has instituted a series of ?management of change? programs that have facilitated an industrial cultural change needed to achieve the company?s vision, mission and strategic goals.

Jan 1, 2005

By José García-Antón, Valentín Pérez-Herranz, José Luís Guiñón, Henry Reyes

"The majority of chromium electroplating operations employ Cr(VI)-based baths. During these processes, Cr(VI) is reduced to Cr(III). Besides Cr(III) other undesirable impurities are present such as iron, copper and nickel. The build-up of the impurities limits the lifetime of the plating solutions. Since the disposal of spent chromic acid baths is expensive and can cause significant environmental degradation, there is increasing interest in finding ways to regenerate waste chromium liquors.In this work, an electrolytic cell separated by microporous ceramic diaphragms was used to regenerate chromium plating solutions. The effect of the ceramic diaphragm structure parameters, such as porosity and pore size, on the performance indicators of the electrochemical reactor (fractional conversion, current efficiency, product yield, specific energy consumption) was investigated.The fractional conversion, the product yield and the current efficiency increased and the specific energy consumption decreased with the decrease in porosity.IntroductionChromic acid is widely used in industrial applications such as steel manufacture, metal finishing industries, aluminium anodising, pasivation of cadmium, magnesium, and zinc, etching of plastics and another industrial operations related with processing ferrous and no ferrous metals [1]. These processes employ baths with high concentrations in chromic acid, about 180 and 350 g/L, where hexavalent chromium is reduced to Cr(III):"

Jan 1, 2008

Testing is in progress to address compatibility issues with regard to long term storage of plutonium in contact with two different intermetallic systems. The two intermetallic systems are: 1. dental amalgam, i.e., mercury plus silver alloy powder, and 2. liquid gallium alloy plus copper powder. Both of these are plasto-metallic materials that undergo a solidification reaction at room temperature. Each system is allowed to react in contact with both high-purity alpha plutonium and a delta stabilized plutonium alloy at varying temperatures in an argon atmosphere. Wetting characteristics and possible interaction will be studied metallographically in the post-mortem condition. Complete results including metallographic examinations will be presented.

Jan 1, 1995

By Funsho K. Ojebuoboh

With several "green" applications in the horizon, bismuth has become an even more important minor metal in the smelting and refining of lead. Smelters with a complex sulfide feed invariably deal with bismuth. Its behavior during the smelting of lead in conventional sinter - blast furnace operation is discussed. Because it readily deports to the lead phase during the refining of lead, its separation from refined lead remained unsatisfactory in early lead production. When commercial requirements of bismuth in lead became more stringent early this century, the procedure whereby calcium and magnesium is used to debismuthise lead was developed. The present conduct of this 1936 process, the Kroll Betterton process, is discussed with emphasis on operational improvements.

Jan 1, 1995

By Sheng-hai Yang

The electrochemical synthesis was conducted in anhydrous ethanol solvent mixed with conductive reagent when tantalum plate was used as anode and stainless steel plate as cathode. The effects of different conductive reagents (such as NH4Br, (CH3)4NCl, (C4H9)4NCl), conductive reagent concentration and the space on the cell voltage and the current density were investigated. The current efficiency of electrosynthesis was more than 95%. The electrolyte, a mixed solution was then undergone air distillation and vacuum distillation to get the final product which was characterized by Fourier Transform Infrared(FTIR) spectroscopy, Raman spectra, 1H-Neclear Magnetic Resonance(1H-NMR) spectroscopy. Carbon and hydrogen contents in the product were determined by elemental analysis instrument. Results consistently show that the product was tantalum penta-ethoxide.

Jan 1, 2006

By Carl A. Kuehn

At Carlin, Nevada, non-indigenous hydrocarbons were introduced as a bitumen phase which was mobilized due to burial under the Roberts Mountains allochthon. similarly, some indigenous organic matter was locally mobilized. Fluid inclusion and paragenetic data of veinlets formed during this hydrocarbon stage, combined with quantitative modelling or organic maturation, indicate that host rocks had evolved past dry gas conditions of around 1550 and l.l+0.2 Kb in the presence of CH4-saturated, highly saline brine by no later than early to middle Cretaceous time. All hydrocarbons present would have been rendered immobile under these catagenic conditions. Crosscutting relationships at several scales suggest that hydrocarbon mobility may have ceased prior to the intrusion of a series of dikes in the mine which have subsequently been altered and mineralized. Apart from subsequent oxidation, the current distribution and high maturity of carbon-rich zones were established prior to gold introduction. No Evidence has been found supporting proposed hydrocarbon "remobilization" during or after gold mineralization and alteration. The high density of the CH4-bearing fluid requires formation at high pressures (near 1 Kb) and precludes their formation as a result of the "cracking-off" of CH4 from organic matter during a thermal event associated with a shallow hydrothermal system. The density and composition of the fluid inclusions restricted to the early hydrocarbon-stages of the Carlin paragenesis are not unique to the sediment-hosted gold deposit environment of north-central Nevada. Similar inclusions are found in authigenic quartz crystals from Paleozoic carbonaceous shales in central Pennsylvania which have experienced normal metagenesis of indigenous organic matter due to deep burial.

Jan 1, 1987

By I. Barin, G. Eriksson, F. Sauert

Computer-aided calculations using data bases and program systems are more and more needed for the rational development and optirnization of high-temperature processes. The calculation of mass and energy fluxes between different process steps as well as the determination of the chemical equilibria will be discussed, giving examples from nonferrous metallurgy. The simulation of a waste-material treatment process including high-temperature combustion and gas-cleaning systems will also be demonstrated.

Jan 1, 1988

By Richard Krentz

Two separate on-line analyzers are operated at the Corefco metals refinery. The first application is an on-line refractometer which measures the ammonium sulphate concentration in the primary feed slurry tank. The second application is a multi-stream X-Ray fluorescence analyzer which measures the metals and sulphur concentrations in eight key refinery streams. Specific applications of the on-line analyzers with advanced control systems for improved process control will be discussed.

Jan 1, 2003

By Tugba Basargan Çagatay Morall, Gülhayat Nasun-Saygili

"The aim of this study is to prepare the apatitic material using colemanite mineral (2CaO.3B2O3.5H2O) which was obtained from Eastern Anatolia, Turkey. For this purpose, colemanite mineral was reacted with different phosphate sources, namely, dipotassiumhydrogen phosphate, ammoniumhydrogen phosphate and ortophosphoric acid at various temperatures and time periods. Experiments were run in batch system. The apatitic material was prepared by a wet method and followed by heat treatment at various temperatures. Structure of the samples was analyzed by XRD, FTIR, XRF and SEM. The particle size analysis was also made for the result product. The experiments showed that reaction temperature, contact time and heating temperature are important parameters to transform the colemanite into apatitic structure. Reaction of colemanite with dipotassiumhydrogen phosphate and ammoniumhydrogen phosphate results in amorphous, non-stoichiometric hydroxyapatite type structure, while acid based phosphate source gives brushite and monetite type product before and after heat treatment, respectively.IntroductionBoron which has properties intermediate between metals and non-metals is a member of semiconductor group of elements. Its atom is very small and has three valence electrons. Boron exists in Earth's crust (from 5 mg/kg in basalts to 100 mg/kg in shale) and in the oceans (4.5 mg/l) [1]. Turkey has 60% of world's boron reserves which is mostly in the form of colemanite (2Ca0.3B203.5H20). Colemanite is the most important calcium containing commercial borate mineral with 5 mol of crystal water [2].Calcium phosphate cements are very useful for bone repair applications because of its chemical structure. They are injectable, easy to shape and can be maintained locally. Because of those reasons calcium phosphate cements are very effective to fill bone defects with an irregular shape [3]. Hydroxyapatite (Ca10(PO)6(OHh) is the major component of the bone (70 wt%). However, hydroxyapatite stoichiometry, composition and crystallinity differ in human skeleton system [4, 5].The main objective of the present work was to study the transformation of colemanite to apatitic material using different phosphate solutions at several time spans and temperatures. The experiments were run in a batch system, change in pH and also weight loss were measured after the experiments. Several analysis methods were used to investigate the chemical and structural changes."

Jan 1, 2012

By Cheng Gong-jin, Chu Man-sheng, Liu Zheng-gen, Zhang Yong, Liu Jian-xing, Xue Xiang-xin

"High chromium vanadium-titanium magnetite is one kind of Fe-V-Ti-Cr composite ore resources, which owes high utilization value. Owing to lacking systematic study on the sintering of this ore home and abroad, effects of carbon addition and basicity on sintering process and sinter metallurgical properties, such as sinter yield, vertical sintering speed, tumbler strength, sinter machine utilization coefficient, and low temperature reduction degradation were investigated systematically under laboratory conditions in the paper. The results shows that, when high chromium vanadium-titanium magnetite proportion is kept unchanged as 13% in sintering feeds, sintering process index and metallurgical properties are the optimum under carbon addition 5.0% and basicity 2.70, which meets the requirements of blast furnace burdens. This research provides technical parameters for practical sintering production of high chromium vanadium-titanium magnetite.IntroductionHigh chromium vanadium-titanium magnetite (hereinafter abbreviated as hi§h-Cr V-Ti magnetite), in which Fe is closely symbiotic with Ti and isomorphous with V and Cr1'- l, is one kind of typical vanadium-titanium magnetite resources with high comprehensive utilization value but the difficulties are extremely high due to complex chemical composition and mineral structure. At present, the feasible and mainstream utilization process of high-Cr V-Ti magnetite should be the route of agglomeration-blast furnace smelting. Thus, sintering production is the foundation for high-Cr V-Ti magnetite utilization. However, till now there are few research documentations on high-Cr V-Ti magnetite sintering home and abroad. Under the above background, this study focused on detailed researches of high-Cr V-Ti magnetite sintering. Sintering process uses the powders or fine iron ores to produce artificial rich ore with good metallurgical properties 4l Solid fuel provides 90% heat requirement during sintering15J. The appropriate amount of fuel and flux should be added during sintering in order to provide necessary heat and maintain the desired basicity16l. That is to say, carbon addition and basicity are two key factors affecting metallurgical properties of sintering products17J. Therefore, the effects of carbon addition and basicity on sintering process and metallurgical properties, including sinter yield, vertical sintering speed, tumbler strength, sinter machine utilization coefficient, and low temperature reduction degradation, are systemically investigated under laboratory conditions in the study, on purpose to achieve the optimization of sintering process for high-Cr V-Ti magnetite."

Jan 1, 2013

By T. J. A. Smith

This paper provides an overview of some of the key issues in design of smelter gas handling systems, with particular reference to sulphide smelting plants. In both primary smelting and converting. gas handling and treatment systems often represent the major capital cost component. There is also ample evidence that poor system design can be a major cause of smelter down time, lost production and unforeseen high maintenance costs. The paper discusses these issues and offers guidance for improved design.

Jan 1, 1992

By Lary L. Speakman

Typical heavy metal removal system generate a great deal of waste that must then be discharged somewhere. Using Bio-Fix Beads developed by the Bureau of Mines in combination with other waste stream minimization processes, Harrison Western Environmental Services has developed a "zero" discharge operation. Data from current on-site operations will demonstrate the effectiveness of the Harrison Western approach. For 1992 Annual TMS meeting,: "Future Trends and Innovations" Material category Key words: Residues and Effluents Technical category Key words: Extraction and Processing.

Jan 1, 1992

By A. C. Cascalheira, L. M. Abrantes, M. Savic

This paper reports our results on the application of a novel process for the spontaneous and sustained reduction and recovery of elemental silver and gold on an electroactive polymer surface. This work incorporates the metal recovery from photographic films (silver) and goldsmith residues (gold), by direct contact of metal containing solutions with polymer. The performance on such process of electrochemically and chemically prepared polyaniline (P ANI) is evaluated. SEM coupled with EDX and XRD analyses confirmed the presence of metallic silver and gold deposited onto polymeric material.

Jan 1, 2000

By N. A. McKay, J. G. Davison

"Heap leachable ore deposits from many countries have been submitted for process mineralogical evaluation and laboratory testwork. Numerous factors must be addressed and integrated by the mineralogist, geologist, metallurgist and engineer. Projects encompass grass roots exploration, preliminary petrographic analysis, predictive and process mineralogy, dye penetration analysis of rocks and thin sections, metallurgical beneficiation testwork and plant optimization studies. The significance of mineralogical factors, such as geological controls, degree of oxidation, dye amenability, liberation, deleterious minerals, refractoriness, and the impact of mineralogy on gold recovery and process considerations, will be presented.ABSTRACT ONLY"

Jan 1, 1997