Search Documents

By Shadia J. Ikhmayies

"Cadmium sulfide (CdS) in the form of thin films is an interesting material because it has a large variety of applications ranging from photovoltaic to luminescent devices. N-type CdS is usually used as a window layer in the heterojunction CdS/CdTe thin film solar cells. A review of the photoluminescence (PL) spectra ofn-type CdS thin films prepared by different techniques was performed. The effects of different dopants and impurities and the effects of temperature and deposition parameters on the PL spectra were discussed. Annealing in different atmospheres causes the changes in material structure and phase change from cubic to hexagonal phase which can be detected through the variations in the PL spectra. CdCh heat treatment improves the cystallinity of the films and enhances the exciton peaks and the green band in the PL spectra.IntroductionThin CdS films deserve attention because their expected gap emission lies very close to the highest sensitivity of the human eye. Thus, one might assume that thin CdS films are an appealing host for photonic devices [ l]. They have been used in a lot of applications including electronic and optoelectronic devices [2]. Thin films ofn-type CdS are widely used as a window layer in heterojunction solar cells such as CdS/CdTe solar cells. Doped and undoped CdS thin films can be obtained by different techniques such as; spray pyrolysis (SP) [3], chemical bath deposition (CBD) [2, 4], pulsed laser deposition [5, 6, 7], laser ablation [l], thermal evaporation [8].Several experimental techniques have been used in order to study semiconductor defects. In particular, photoluminescence (PL) has been shown as a powerful and sensitive tool in examining the crystal quality of polycrystalline thin films. PL can be used in the detection of defects which are radiative active. These defects can also act as traps in the transport of carriers [9]. The photoluminescence (PL) of thin film CdS is strongly influenced by the unbalanced stoichiometry, which is typical for CdS and is in general evoked by a Cd surplus. With increasing Cd content, the emission spectra move far below the gap to the red spectral range. Besides stoichiometry problems, independent of the material deposited, the PL properties of thin films depend on surface features and the influence of the interface between the film material and the substrate [10]."

Jan 1, 2013

By R. M. G. S. Berezowsky

Treatment of Hudson Bay Mining and Smelting Co. Ltd. (HBM&S) zinc concentrate in the Sherritt zinc pressure leach process produces a residue containing elemental sulphur, residual sulphides, precipitated iron species, si1ver and gold. Flotation of the residue recovers most of the elemental sulphur and residual sulphides to the concentrate, leaving iron oxides and bask sulphates in the tailings. The tailings also contain most of the sflver and some gold. Direct cyantde leaching of the oxide tailings (220 g/t Ag, 1.4 g/t Au) was capable of leaching most of the gold, but only a minor portion of the silver. This paper reports testwork, conducted by Sherritt on behalf of HBM&S, to define a process for a high recovery of the precious metals from the oxide tailings. A si1ver enhancement treatment, consisting basically of digestion of the residue with lime at 90°C to render the silver amenable to enhanced recovery by subsequent cyanidation, was selected as the most promising approach. Batch silver enhancement and cyanidation tests showed that treatment of the oxide residue with 80 kg/t CaO at 90°C for 1 to 2 h increased the silver extractability in subsequent cyanidation from <20% to 96%. A 96 h continuous miniplant test (1 kg/h solids feed rate), of a circuit including a silver enhancement treatment step followed by conventional cyanidation and carbon in pulp silver and gold recovery, confirmed metal recoveries to the carbon of 90% Au and 96% Ag. Reagent consumption rates were 1ess than 100 ?kg/t CaO and 5 kg/t NaCN.

Jan 1, 1990

By Jay. M. Khodadadi, Josef Štetina, František Kavicka

"With the aid of the proper original numerical model of solidification the instruction for preparation of input parameters for numerical simulation of technological processes, with change of the phase or structure, will be presented. A method of calculation analysis of influence of therrpophysical properties of materials entering the system of casting-mould-cores environment, and also of boundary conditions on the required simulation accuracy will be suggested. For the cast material, the influence of heat .conductivity, specific heat capacity, density and latent heat of phase transformation also has been analysed. For metallic or non-metallic moulding material"" the influence of the see main parameters has been analysed and, furthermore, their combination, influence of thermal conductivity, and of heat storage. The order of influence of all quoted parameters of a casting and moulding material was established. For example heat conductivity in the liquid state is on the last place. From the boundary conditions the -most important influence on the total solidification time and · on the mechanism of forming of temperature field has the ·boundary condition on the casting mould boundary, then follows the boundary condition on the level of a molten metal. The negligible influence has the boundary condition on the mould frame and on the bottom.IntroductionThe original and universal mathematical model of solidification, cooling and heating has been set up and checked, in order to be capable of analysing a one- to three-dimensional steady or unsteady temperature field of the casting-mould-environment system and, namely, of the system as a whole or its arbitrary parts, during any industrial technological process whose individual processes could be solidification, cooling, heating, refrigeration and others, in any sequence or singly. The model enables the simulation of traditional and also non-traditional technologies of casting in foundries, metallurgical plants, forging operations, heat treatment processes, etc. If solidification is not the matter, the metal part of the system need not be called the casting but a component, a block, a forging and the like."

Jan 1, 2000

By Feng Liu, Bingji Yan, Zhiwen Shi, Hongwei Guo, Jianliang Zhang

During production of a large quantity of steel, slag is produced at the same time. This paper chooses blast furnace slag (BFS) as the main material for the research. The purpose of the research is to explore its optimal physicochemical properties and the use of BFS in building stone field. The paper elaborates the experimentation process of producing glass-ceramics and presents the results. The results show that SiO2 content in BFS and amount of Cr2O3 and Fe2O3 added as nucleating agents have certain effect on the properties of glass-ceramics. The results also show that the exothermic peak temperature of base glass is the lowest when adding 20% SiO2 to the BFS, and 2% Cr2O3 and 3% Fe2O3 as nucleating agents, which makes easy crystallization and optimal properties of the glass-ceramics.

Jan 1, 2015

By M. Tamura, K. Fujita, K Shinozuka, H. Daimon, H. Esaka

"In-situ observation of unidirectional solidification using transparent substance has been performed to investigate the growth direction of solid phase. Cell or dendrite of which preferred growth direction is not parallel to the heat flow direction was observed with various solidification conditions. Dimensionless growth direction (p) changes from 0 to 1 with increasing growth velocity at a constant temperature gradient. Introducing the dimensionless growth velocity, the relation between p and growth condition could be correlated.IntroductionTransition in macroscopic solidified structure from chill to columnar zone which is found in normal castings takes place via grain selection1). Cast products such as turbine blades are unidirectionally solidified, grain selection plays an important role to choose suitable crystals which have reasonable orientation in the region called ""starter"", which is a very initial part of casting2). Therefore, grain selection is a very important process in the formation of casting structure. The present authors have been studying on the process of grain selection using succinonitrile, which is a transparent organic substance and have found that the growth distance necessary for grain selection depends upon the solidification condition3-5). When the solid/liquid interface is dendritic, the grain selection occurs quickly. On the other hand, when the solid/liquid interface is cellular, it occurs slowly. We supposed that the growth direction of dendrite is different from that of cell when the substance is unidirectionally solidified. Indeed, Kurz and Fisher wrote in their text book that dendrite grows along its preferred growth direction, <100>, regardless of heat flow direction and that cell grows along heat flow direction regardless of its preferred growth direction1). However, there is no quantitative description about the growth direction when the solid/liquid interfacial morphology is cellular. Furthermore, there have been little works6) to study the growth direction of cell and dendrite."

Jan 1, 2000

By Hiroshi Nakajima, Kotobu Nagai, Toshihiro Hanamura

"Low carbon ferritic steel bars with ultra-fine grain structure was developed through a warm rolling for the first time by the present authors. They show better low temperature toughness than conventionally hot-rolled plates. Hence, the brittle fracture surfaces in Charpy tests were examined in terms of the effective grain size of fracture, compared with those of conventional QT steels. The ductile-to-brittle transition temperatures were in good accordance with those for the QT steels if referred to the effective grain size of fracture: · However, the size was a few times that of the ferrite grain. This means the grain refining is not yet fully utilized from the viewpoint of low temperature toughness. The anisotropy of· the impact properties and the annealing effect of highly dislocated structure on the toughness are also discussed in the present paper.IntroductionFor structural materials, both high strength and good toughness are required. Well-known approaches for obtaining better toughness for steels are as follows:1) Grain refining2) Addition of Ni3) Thin plate effect by cracking parallel to the rolling direction prior to crack propagation4) Contribution of metastable austenite.Among them, only the grain refining can raise the strength and improve the toughness. And it is well known that the finer the ferrite grain size, the lower the ductile-to-brittle transition temperature. For example, in the case of 0.11 carbon steel, the transition temperature decreases linearly to in d 1/2 [1 ]. However, these have been told in the regime of coarse grain size that is larger than 10 µm in diameter. There ~as .been no study dealing with the low temperature toughness in the regime of ultra-fine grain size with a diameter in the order of 1 µm."

Jan 1, 2000

By Z. Zhang, Cuihuan Huang, Zongshu Zou, Nan Wang, Xueqian Xin

"Vitrification is considered as an attractive procedure for municipal solid waste incineration ash, which can realize the volume reduction and innocent treatment of incineration ash, as well as reuse of bottom ash. The main oxide components of molten ash slag are CaO, Al2O3, SiO2, Fe2O3, MgO, and Na2O, accounting for more than 90% of the total mass. The phase relations and thermodynamic properties of the CaO-Al2O3-SiO2-FeOx-MgO-Na2O oxide system is highly required, and is of great scientific significance for optimization of vitrification processing and sustainable resource utilization of melting slag. A study on the equilibria phase relations of CaO-SiO2-MgO-FeOx system was done by using CALPHAD method based on FactSage in this paper. The modeling parameters for the thermodynamic properties of liquid phase in CaO-SiO2-MgO-FeOx system were established and the equilibrium phase relations of MgO-SiO2-FeOx and CaO-SiO2-FeOx-MgO systems were calculated for different temperatures and oxygen partial pressures.IntroductionThe main oxide components of vitrified bottom ash slag are CaO, Al2O3, SiO2, Fe2O3, MgO, and Na2O, accounting for more than 90% of the bottom ash by weight [1]. During slag processing and modification, the knowledge of thermodynamic properties and liquidus temperature in the related slag system is highly required [2-5], which is not yet available. Through literature survey [6-9], it is clear that the systematic information on the concerned complex slag system is scarce. Most binary subsystems except FeOx-Na2O have been investigated well. Among ternary subsystems, few phase relations of the Na2O-MgO-SiO2 ternary system are available. For the phase relations of the system Na2O-MgO-Al2O3, all the studies are focused on the Al2O3-rich region. Investigation on the CaO-Al2O3-FeOx system is limited to Fe2O3-containing system with relatively higher oxygen potential. Most quaternary systems are not studied well except the CaO-MgO-Al2O3-SiO2 system, mainly due to their metallurgical importance. Figure 1 demonstrates the research status of the vitrified bottom ash slag with almost zero effort [10]. The effort here is defined based on the published literature by considering the number of publications, the investigated composition ranges, and the research details. So far the engineers in the field have to make assumptions of the thermodynamic properties of the simplified oxide system, without taking into consideration the interactions of the different oxide components, which hinders the development of the slag valorization and utilization. In order to provide thermodynamic properties for the application of the vitrified bottom ash, the six-component oxide system (CaO-MgO-Al2O3-SiO2-FeOx-Na2O) will be investigated through both experimental approach and computer modeling."

Jan 1, 2011

By Jie Ma, Bo Wang, Jieyu Zhang, Jian Zhao, Guangxin Wu, Shunli Zhao

"Nucleation and growth model based on a 3D CAFE model, which was incorporated with macro heat transfer calculation within ProCAST software was used to predict the solidification microstructure of austenitic stainless steel in twin-roll strip casting. The simulation results of solidification microstructure agreed well with experimental results of austenitic stainless steel. The effect of different casting process parameters on the solidification microstructure was simulated. The predicted results show that solidification microstructure is obviously sensitive to superheat and convection heat transfer coefficient. With the increase of superheat, the grain density decrease and the proportion of columnar crystal increase. In addition, the proportion of columnar grains increases when convection heat transfer coefficient increases. Thus, it was demonstrated that the solidification microstructure evolution of twin-roll strip casting could be predicted reasonably by using this model.IntroductionNear-net-shape casting technology is an important research area in the iron and steel industry today. Twin-roll strip casting represents a major area of concentration of near-net-shape casting technology. It has been widely used for its outstanding advantages, such as extended solubility of alloying elements, refined solidification microstructure and reduced microsegregation [1]. Furthermore, it is the most environmentally friendly, energy saving, and C02-sensitive way to produce steel strips [2]. Therefore, much attention remains to be paid to this aspect. A lot of published works indicated that the solidification microstructure of twin-roll thin strip has obvious effect on the thin strip properties [3, 4]. For the accurate control of parameters of the process are made difficult due to the complicated process and the multi-fold factors, great attentions have been paid to numerical simulations to provide insight into the solidification behaviors of the thin strip formed by twin-roll strip casting [5, 6].Simulations of casting solidification can provide a method to predict microstructure and to improving strip quality by controlling the process parameters."

Jan 1, 2014

By S. N. Lekakh

Experimental work and thermodynamic simulations of cast iron refining were carried out using various additions of alkali and rare earth metals. The refining reactions for sulfur and oxygen removal were studied for melts treated with Mg, Ca, and Ce. The measured data and the results of the computer simulations were in agreement. Experimental kinetic data, together with the thermodynamic calculations, were used for optimization of the amount and sequence of the addition of nodulizers for ductile iron production.

Jan 1, 2009

By C. L. Lin

Transformation of linear grade distribution to volumetric grade distribution has been used to estimate the actual mineral liberation during wet, batch, ball mill grinding of a copper ore. The degree of liberation based on the multicomponent-multisize grinding liberation model using volumetric grade is lower than the apparent degree of liberation estimated from using King&apos;s linear intercept model.

Jan 1, 1987

By Zongshu Zou, Qiang Li, Mingming Li, Mingxia Feng

The impingement onto the surface of bath by top-blown jets is a significant process characteristic in BOF and EAF steelmaking process. The cavity is one of the most important outcomes of the interaction and plays an important role on reaction kinetics and reactors performance. But to date, the understanding to cavity is still so limited. In present study, a water model for a BOF converter is established and the dimension of cavity profile is investigated. The effects of lance height, gas flow rate, nozzle inclination angle and the amounts of slag are discussed. The results show that penetration depth increases with the increase of gas flow rate and the amount of slag, and the decrease of lance height and nozzle inclination angle. Furthermore, a theoretical model of cavity dimension is proposed for multiply jets impinging liquid bath on the basis of energy balance at the stagnation point of cavity.

Jan 1, 2015

By S. Sundarraj

The morphological transition between columnar and equiaxed structures is an important solidification phenomenon frequently observed in castings, especially complex parts with varying cross-section, The mechanical properties and the occurrence of defects such as hot tears are strongly dependent on the structure formed in the casting. Hence, it is important to understand the conditions leading to columnar or equiaxed structures. Although extensive work has been done in modeling solidification systems, almost all of the existing models are based on the assumption that the structure formed in the casting is either purely columnar or purely equiaxed. Prediction of the columnar-equiaxed transition (CET) requires a solidification model which accounts for the formation of both columnar and equiaxed structures, along with related microscopic and macroscopic solidification phenomena. In this paper a CET model is presented which: (i) takes account of both columnar and equiaxed structures, (ii) accounts for macroscopic heat transfer coupled with microscopic phenomena such as nucleation, growth and microsegregation, (iii) satisfies solute conservation, and (iv) is easy to implement in commercial finite element and finite difference software. The proposed model predictions of CET have been validated with available experimental results for a uni-directional solidification of an aluminum-copper alloy. A sensitivity analysis has also been carried out to determine the effects of various parameters on the CET model predictions. The model is being extended to other alloy systems and more complex geometries. This work will be published in due course.

Jan 1, 1996

By W. Zhao

Several years ago, Reddy and Blander presented upriori model for calculating the sulfide capacity of binary silicate melts. It is modified now to apply to CaO-AlO 1.5 melts at different temperatures and compositions. Our predictions are in very good agreement with the available experimental data. From a comparison of binary calcium aluminate and calcium silicate systems, higher sulfide capacities are obtained in aluminate systems. The sulfur can be removed from hot metal more effectively by adding aluminate melts.

Jan 1, 1995

By A. Warczok

The heat transfer coefficient between liquid slags and solid surfaces is important for the design and operation of metallurgical reactors. An experimental technique developed for the purpose of measuring the heat transfer coefficient between liquid slags and solid metals is described. During the initial heating up of a Ni cylinder upon immersion in a liquid slag, a layer of frozen slag initially forms, then melts. The heat transfer coefficient measured during the initial rapid heat-up of the Ni cylinder, is approximately twice as high as the heat transfer coefficient measured during the final heat-up of the Ni cylinder subsequent of the liquidus temperature of the slag. The technique was tested in various melts i) NaNO3, ii) NaCl, iii) Na3AlF6 and iv) 2FeO*SiO2, giving consistent results. It was found that the heat transfer coefficient increases with increasing bath superheat and stirring. The heat transfer coefficient during the heating up following complete remelting of the frozen slag, is related to the slag superheat(AT) and the specific stirring energy(W) per kg of slag(E) as follows.

Jan 1, 1993

By S. Yokoya

With increasing requirement of steel productivity and quality in continuous casting in the conventional casting system using an immersion nozzle, it is very difficult to establish a reasonable molten flow pattern. In order to overcome this difficulty, we propose a new method of imparting swirling motion onto the flow in the immersion nozzle and to control the flow pattern in the mold. Following results have been obtained during the studies. For the case of slab continuous casting mold: High amplitudes of oscillation with a period of 10 to 15 seconds are observed in the outlet flow of the immersion nozzle and meniscus flow in the conventional casting system, while these phenomena are remarkably suppressed using swirling motion in the immersion nozzle, which leads to very calm and uniform flow pattern at the outlets of the immersion nozzle, in the mold and on the meniscus in the mold; For the case of billet continuous casting mold: (1) heat and mass transfer near the meniscus can be remarkably activated compared with a conventional straight type immersion nozzle without swirl, and (2) Quite different mold flow patterns are observed between the divergent and straight immersion nozzles. Heat and mass transport in the mold using the divergent nozzle is much more reasonable compared to that of straight nozzle. The findings, mentioned above, are very useful to control the flow pattern in the slab, and billet continuous casters. Such effectiveness of swirling flow in the SEN on the mold flow has been put into practical use. As a result, remarkable progress on the quality and production of continuous casting products has been observed in practical application.

Jan 1, 2006

By Teruhisa HORITA

The durability of SOFCs is one of the critical issues to realize the SOFC systems. In order to improve the durability, a precise degradation mechanism should be clarified at the different functional ceramic interfaces in SOFC cells and stacks. This paper reviews the improvement of SOFC durability by the mass transport analysis especially at cathode/interlayer/electrolyte interfaces. We have made a precise analysis on the reaction of cathode with impurities. Especially at the (La,Sr)(Co,Fe)O3/CeO2/ZrO2 interfaces, a significant amount of SrCrO4 and SrSO4 were observed at the (La,Sr)(Co,Fe)O3 surface as well as inside the (La,Sr)(Co,Fe)O3 cathode, which suggested some process occurred for both poisoning. Possible degradation mechanisms were proposed based on the observation data.

Jan 1, 2016

By Ilona Johnson

United States metals and non-metallic minerals manufacturing consume about 5,000 trillion Btu annually. Various studies estimate that as much as 20 to 50 percent of this energy is lost as excess or waste heat. Recovery of waste heat can conserve energy, reduce operating costs, and lower environmental emissions. It would be valuable to quantify recoverable waste heat sources and identify the barriers that hinder its recovery. This paper provides an overview of waste heat losses specific to high temperature processes in primary metals and minerals manufacturing. It summarizes findings from a broader study conducted for the Department of Energy Industrial Technologies Program; the study evaluates energy losses, recovery practices and opportunities, and R & D needs for waste heat technology development.

Jan 1, 2008

By Ragnhild Aune

In fire refining of copper, the affinities of various impurity elements on dissolved oxygen is of great significance. Further, in the design of oxygen probes in liquid copper, the influence of solute interactions on the activity of oxygen need to be considered in order to evaluate the oxygen concentration in molten copper. The present paper presents a series of measurements of the activities of oxygen in liquid Cu-M-o alloys (where M stands for Mn, Zn, As, Se or Te) carned out by the present group employing the solid electrolyte galvanic cell technique. Extreme care was taken to control the oxygen potentials in the inert gas atmosphere, and to keep the oxygen levels very low in the molten metal. The oxygen content was determined by analysis of the samples taken out from the melt. The results obtained showed that Mn has a strong negative influence on the activity coefficient of oxygen in liquid copper. A similar, but less prominent effect was observed in the case of Zn. Arsenic had no influence on the activity of oxygen in Cu (liq.). Se and Te had slight negative effect on oxygen activities in copper at XQ >10-5, while at lower oxygen levels the interaction coefficients were found to be positive. The results obtained were compared with empirical models for the calculation of interaction coefficients available in literature.

Jan 1, 2003

By Ana P. Paiva, Marc F. Comella, Sandra S. Reis, Joao N. Reis, M. Soledade Santos

"In this work, the influence of the malonamide structure, acidity of the aqueous phase and diluent on the equilibrium interfacial tension (IT) of N,N'-dimethyl-N,N'-diphenylmalonamide (DMDPHMA) and N,N'-dimethyl-N,N'-dicyclohexylmalonamide (DMDCHMA) in 1,2- dichloroethane (1,2-DCE), and DMDCHMA in toluene, with aqueous HCl, were investigated. IT isotherms were determined using the Du N ouy ring method. Densities of the organic phases were determined, and used to screen solute-diluent interactions. Formation of third phases was never observed; furthermore, ITs increase with the phase separation period, constant values being obtained for separation periods larger than 1000 seconds. Each malonamide interfacial efficiency at the oil/water interface is interpreted in terms of malonamide basicity, diluent polarity and malonamide - hydrochloric acid- diluent interfacial interactions.IntroductionFor several years now, N,N'-tetrasubstituted malonamide derivatives have been extensively investigated as liquid-liquid extraction agents since they were first proposed as the organic components of the DIAMEX process, with the aim of advantageously replacing tributylphosphate in PUREX [1]. Therefore, a significant part of research studies with malonamides appearing in the literature deal with the extraction of major and minor actinides in real or simulated spent nuclear fuels in nitric acid solutions [2]. Under typical experimental process conditions, the tendency shown by some N,N'-tetrasubstituted malonamide derivatives to aggregate in the organic phase, leading in a few cases to the formation of undesirable third phases, has been remarked and consequently thoroughly investigated [3, 4]. The increasing use of chloride streams as hydrometallurgical aqueous feeds is becoming a reality, and this fact is obviously deeply founded on an extensive research carried out to recover value-adding metals from these media. Following this trend, a number of N,N'-tetrasubstituted malonamides have already been screened for the recovery of iron(III) [5, 6] and platinum-group metals [7] from hydrochloric acid solutions. The results obtained are quite promising either in terms of total metal ion recoveries or selectivity patterns achieved. The formation of a third phase when iron(III) was extracted by the tested N,N'-tetrasubstituted malonamide derivatives has never been observed under the adopted experimental conditions, and the extraction data collected would need to be reinterpreted accordingly if any aggregation phenomena involving the considered extraction systems were to take place."

Jan 1, 2011

By Gabriel Riveros

Fire refining of copper consists of two stages copper oxidation and copper reduction. Very frequently the capacity of the anode furnace is determined by the rate of copper reduction. The analysis of factors affecting the rate of the oxygen reduction from a liquid copper with solid carbon or injected hydrocarbons pointed out the role of the mass transfer in a liquid copper in final stage of the reduction. Experimental results of copper reduction with graphite and injected natural gas in laboratory- scale crucibles showed two stages of the reduction process with a sharp change of the controlling mechanism. The estimated dynamic surface area of gas bubbles based on the measured bubble frequency and the gas flowrate allowed for the detennination of the reaction constant as a degree of the partial pre-combustion of the air/natural gas mix. The variation of the used reductant as a function of the oxygen concentration and temperature has been evaluated based on the detennined kinetic model. The intensification of copper reduction in fire refining has been discusses on the basis of obtained kinetic data and analysis of various factors detennining the time of reduction.

Jan 1, 2003