Search Documents

A novel, low-pressure adaptation of Praxair?s coherent jet technology utilizing CoJet lances was developed for application at Inco&apos;s Copper Cliff Smelter where oxygen is available in large tonnage quantities but only at relatively low supply pressures (< 193 kPa header pressure). The project objectives were to evaluate the effect of coherent jet technology on controlling oxygen lance accretion (?horn?) formation and to increase oxygen efficiency in the Inco Oxygen Top-Blowing Nitrogen Bottom Stirring (TBBS) MK Reactor used for converting nickel- contaminated chalcocite to semi-blister copper. This paper describes the development and subsequent implementation and testing of two CoJet lances in this application.

Jan 1, 2005

By Hiroshi Tabuchi, Akihiko Takahashi

"High strength aluminum matrix composites were prepared and studied using as reinforcement newly developed nearly mono-dispersed a-alumina single crystal particles each of which has a regular polyhedral shape. The composites were formed by centrifugal casting using aluminum casting alloys (Al-Si and Al-Cu-Mg) as the matrices, followed by heat treatment. The volume fraction of the alumina particles was as high as 60%. The same matrix composites reinforced by conventional crushed fused alumina particles were similarly prepared as the reference. The bending strength and tensile strength of the Al-Cu-Mg matrix composites reinforced by the novel alumina particles of 10 µm in average diameter are as high as 1020 MPa and 560 MPa, respectively, which are higher than those of the conventional alumina composites. Furthermore, the bending strength of the novel alumina composites degraded less than that of the conventional alumina composites after thermal fatigue tests. The number of cracks in the matrix seemed to influence the thermal fatigue property because many cracks were observed in the conventional alumina composites, whereas only a few cracks were observed in the novel alumina composites. This was confirmed by SEM observation of the sample composites before and after the thermal fatigue tests.IntroductionAluminum matrix composites strengthened by dispersed reinforcements are of interest for various applications due to their improved properties, such as high specific strength and stiffness, wear resistance, etc .. A large number of investigations have been made concerning fabrication processes and properties of these composites. With regard to the fabrication processes, powder metallurgy has been well-known as a solid phase process, and recently many liquid phase processes such as a compocasting, a squeeze casting, the Lanxide process, and the Osprey process have been studied and developed.(1)"

Jan 1, 1998

By Bin Xu, Qian Li, Xiaoliang Liu, Yongbin Yang, Tao Jiang, Yan Zhang

The cohering behavior of iron ore pellet powder in kiln cannot be reflected entirely through the conventional briquetting method, so a novel natural stacking method was proposed in this paper. The results showed that in the two methods the cohering strength of powders from different iron ore pellets (numbered A, B and C) rose with the increase of roasting time and temperature andpresented the same result, i.e., C > B > A. Comparatively, the natural stacking powders obtained much lower cohering strengths under the same roasting condition. The structure analyses of ring from the kiln tail and cohering briquette by the natural stacking method indicated that the occurrence of crystallized particles of them were extremely similar. Therefore, the initial information of pellet powder’s cohering behavior could be provided by the natural stacking method, improving the methods to study the actual ringing process and mechanism of pellet powders in kiln.

Mar 1, 2017

By W. G. Davenport

Most pre-t 988 Outokumpu flash furnaces were built with blast heaters. Many continue to use them. Blast temperatures in these smelters· are typically 400 to 700 K (Table 2. 1) This chapter: (a) shows how hot blast is included in our calculations (b) evaluates the effects orhot blast onauthothermal65% Cu matte production.

Jan 1, 2001

By Admire Chaendera

A gas jet was blown through submerged nozzles to stir the bath in the presence and absence of slag. Mixing and mass transfer rates were then studied. Water and kerosene (10% by volume) were used to simulate the metal and slag phases respectively in the cold model. The mixing time (Tmix), defined at 99.66% bath homogeneity level, increased with bath height and decreased with an increase in the gas injection rate. Its value in the model vessel was related to gas flow rate (Q), bath weight (W), and bath height (H) by, Tmix = 4.39Q-0.73W0.24H1.12. Inclusion of the slag phase increased Tmix by about 16% and the mass transfer parameter, [(Reloc,r)0.25(Ret)0.32], values by about 32%. Mass transfer rates were higher near the bath surface and in the gas-liquid plume region. They increased with gas flow rate but decreased with an increase in bath height. The relationship, K Q0.08, showing derived mass transfer coefficient (K) dependence on the gas injection rate (Q) was established. The proportionality constant in the equation varied with gas flow rate and sample location.

Jan 1, 2006

By Thamyres C. Carvalho, Edemarino A. Hildebrando, Roberto F. Neves, Francisco R. Valenzuela-Diaz

Synthetic clays are an option of materials that can be modified to obtain better and specific properties when compared with natural clays. Although clays are found in nature, they have many disadvantages that limit the use of them, such as existence of impurities, and variations in composition. Therefore, the objective of this work was to obtain synthetic clay/polyester resin nanocomposites. To characterize the clay, we used X-ray Diffraction (XRD), Total Attenuated Reflection Spectroscopy in the Fourier Transform Infrared Region (ATR-FTIR) and Scanning Electron Microscope with Field Emission (FEG-SEM) methods and the nanocomposites were characterized by XRD and mechanical resistance to compression. The results show the purity of the clay and the time of synthesis is an important parameter for its crystallization process. The clay/polyester nanocomposites were obtained and showed an increase in the ductility.

Mar 1, 2018

By Chen Qizhou, Wang Yun, Zhu Rong

SiO2 and Al2O3 in the metallurgical slag of nickel laterite ore have great recycling values. In this work, Si and Al were extracted from the slag in NaOH based molten salts through alkali roasting and water leaching process for preparing zeolite materials. The extraction ratio of SiO2 increases with increased temperature and appropriately prolonged time, and more than 80% SiO2 can be recycled from the slag after roasting at 550°C. Si and Al from the slag are in the filtered liquor for producing zeolite materials, while Mg, Ca, Fe and other impurities remain in the leached residues. Adding Na2CO3 into the alkalin-slag roasting process can reduce the amount of pure NaOH used with minor decrease in extraction ratio of SiO2, while make better separation of Ca to avoid it getting into the filtered liquor. Adding Al2O3 into the alkalin roasting process can replace part of more expensive NaAlO2 addition that is required for preparing zeotite material, which may bring out a minor decrease in extraction ratio of SiO2 due to formation of NaAlSiO4 in the filtered residues. Quality X zeolite and 4A zeolite materials can be made from the starting liquor containing Si and Al recycled from the laterite nickel slag through alkali roasting and water leaching process.

Mar 1, 2018

By Mariana M. Arantes, F. R. Valenzuela-Díaz, Olgun Guven, Vijay K. Rangari, Julyana Santana, Esperidiana Moura

Nowadays, the development of polymeric materials reinforced with residues of vegetal fibers is becoming popular for application in different segments, from the automotive to the civil construction and furniture industry. Vegetal fiber residues may be used as reinforcement of the recycled polymer materials, for instance, to produce foams to packaging or to thermal and acoustic isolation for green building application. This work is focused on the development and characterization of recycled-HDPE/EVA foam reinforced with fiber residues from babassu coconut epicarp. Firstly, composites based on recycled-HDPE/EVA blend reinforced with babassu coconut fiber were obtained by melting extrusion process. The composites were then extruded in a special single screw for foaming. The foam samples were submitted to mechanical tests, density measurement, DSC, TG, and FE-SEM analysis.

Mar 1, 2018

By R. David Prengaman

During the past several years a new insoluble lead anode has been developed for copper electrowinning. The new anode consists of a rolled lead-calcium-tin alloy sheet attached to a slotted copper bus bar by a soldering process which produces a complete metallurgical bond between bar and sheet. The metallurgical bond greatly reduces the resistance between the bus bar and the lead sheet and the high conductivity does not deteriorate during the life of the anode. The rolled anode thins uniformly and does not suffer preferential grain boundary or internal corrosion commonly seen in cast anodes. The lead-calcium alloy containing a high tin content corrodes slowly because the rolling process produces a uniform, fine grained structure. The wrought product is very strong and ductile; and contains no internal defects, segregation, cracks, or pores which can reduce the life of the anode. Because the anodes corrode uniformly, a high percentage of the anode thickness can be utilized thus extending the life of the wrought anodes. The anode alloy composition which is stable only in wrought form, produces exceptional resistance to passivation during current interruptions. First introduced into liberator cells, the new electrowinning anodes have been specified as the anodes of choice for every new SX-EW tankhouse constructed in the last two years. This paper describes the new anode, its method of construction, service history, and how it differs from present copper electrowinning anodes.

Jan 1, 1987

By Binxu Zhaug, Mark Jolly, Xiaojun Dai

"In conventional investment casting process of aluminium alloys for the application of the aerospace industry, to assure the quality of the final casting, usually the foundry uses large runner system which results in low yield, high energy consumption and high GHGs emission. In one case of this investigation, the yield is between 5 ~ 10% which means that the current casting process wastes large amount of energy and generates lots of scraps. By applying a new casting method, the bulky runner system and the melting/holding time are significantly reduced, the quality of the casting is improved, and in the meantime the related energy consumption and GHGs emission are significantly decreased. In the investigation, the energy efficiencies and GHGs emission between the current and traditional processes are calculated and compared.1. IntroductionAs one of the conventional casting process, Investment Casting Process (ICP) and its applications can be traced to thousand years ago [l]. In current casting industry, ICP still plays an important role in the production of small and precious castings with high quality requirements in automobile and aerospace industries. Both casting quality and manufacturing costs which mainly consist of energy costs have crucial effects on the competitiveness of castings in the market. In the production of aluminium alloy castings using ICP, the energy cost and energy efficiency of a casting facility depend mainly on the efficiency of its melting and heat treating performance. In association with the two performances, more than 60 % of the total process energy costs are symbolised in a typical casting facility [2]. Additionally, in conventional ICP of aluminium alloys for the application of the aerospace, to assure the quality of the final casting, typically the foundry uses huge runner system including big risers/feeders which cause low yield, creates lots of scraps and generates high energy consumption. Consequently, there are huge opportunities for casting industry to choose the best practices for potential energy saving. Furthermore, the reasons such as the stringent limitation of environmental legislation in Europe and the pressure of the rising energy price force the casting industry to reduce the energy consumption and greenhouse gases (GHGs) em1ss10n."

Jan 1, 2012

By V. Panchanathan

The rapidly solidified Nd-Fe-B powders form the entire basis of the bonded magnet industry At present the rapid solidification is carried out exclusively by melt spinning, producing flake like particles having highly stable and magnetically hard microstructure These particles are comminuted into powder before being processed into bonded magnets These powders are magnetically isotropic having coercivities from 4 to 16 kOe The other type of powder recently introduced for bonded magnets is the anisotropic powder made by the hydrogen decomposition desorption recombination (HDDR) process. The characteristics and application of these isotropic and anisotropic powders are discussed.

Jan 1, 1997

By K. C. Chou

The surface effect is one of fundamental topics in physical chemistry that has been studied over decades. However, its effect has been neglected in metallurgy researches and industry applications in the past years. With the progress of science and technology in metallurgy, the consideration of surface effect to the metallurgical processes has been paid more and more attention. In this report, it is shown that, how this factor affects the physicochemical properties of metallurgical processes and how to derive some new and more correct theoretical formulae for its application. Besides, some new technique related to the application of this factor in the experiment has also been developed for both fundamental research and industry applications. It is hoped that these progresses will promote some new developments both in fundamental and industrial applications for metallurgy processes.

Mar 1, 2017

By William Petruk

The concentrator of the Iron Ore Company of Canada consists of spiral circuits, a cone plant and a magnetics plant with regrind. The proportions of liberated and unliberated grains of iron oxides at each point throughout the concentrator were measured by image analysis, and recoveries were calculated for each particle type by the MATBAL materials balancing program. The results show that spirals and cones recover more than 92% of the liberated iron oxide grains in the size range of 848 to 150 um,, but the recovery drops off rapidly for finer grained particles. The tailings from the spirals and cones are reground and low intensity magnetic separators are used to recover liberated magnetite in the -37.5 um size range. The concentrator does not have a unit that efficiently recovers iron oxide grains in the size range of 150 to 37.5 um Consequently about 25% of the iron oxides in the ore are lost to tailings as liberated. grains in the size range of 150 to 37.5 um

Jan 1, 1989

By Rune Gammelsmter

Turbulent chemically reacting flows are generally very complex, involving interactions of chemical, thermodynamic, and fluid mechanical processes. A combustion model based oh algebraic moment closure has been developed. The model is applicable for reaction rates where the chemical kinetics can vary from slow to fast. The effects of turbulence is taken into account by means of modifications to the well known k-e modelling procedure. The model is applied to an industrial combustion process. Calculation of furnace off-gas combustion from an aluminum reduction cell has been performed. The theoretical results agree well with experimental values.

Jan 1, 1992

By Tae-Hyun Kim, Kang-In Rhee, Jeong-Soo Sohn

The synthesis of Mn-Zn ferrite powder from spent zinc-carbon batteries was investigated using a series of physical treatment, sulfuric acid leaching and coprecipitation. Physical separation methods such as crushing, magnetic separation and sieving were applied to generate a non-magnetic material of 8- mesh undersize for subsequent leaching process. The 8-mesh undersize of the spent zinc-carbon batteries was assayed 23.9% Mn, 14.9% Zn, and 4% Fe. Metal extractions obtained in sulfuric acid leaching at the solid/liquid ratio of 1:10, 2 M H2SO4, and 60? with 6 vol.% H2O2 addition were 97.9% Mn, 98.0% Zn and 55.2% Fe. The leach liquor was finally adjusted to the Mn:Zn:Fe mole ratio of 1:1:4 suitable for producing MnZnFe4O8 ferrite powder by the addition of Mn, Zn and Fe sulfates followed by pH control. A co-precipitation test for Mn-Zn ferrite powder was performed at 80?, O2 gas flowing at 1.3 L/min. As a result of co-precipitation, Mn-Zn ferrite nanoparticles in 20 nm size with spinel structure were successfully synthesized. The saturation magnetizations of Mn-Zn ferrite powder (Mn1-xZnxFe2O4) were determined to be 39-91 emu/g with various zinc contents (X=0.2-0.8).

Jan 1, 2008

By Alexandra Anderson

A computational fluid dynamic (CFD) model has been developed using ANSYS Fluent 17.0 to help identify areas of high wear within the refractory lining of a secondary lead reverberatory furnace. Once a base case simulation was validated using data from an operational furnace, areas of potentially high refractory wear were determined through the calculation of the temperature and velocity distributions within the furnace and on the hot face of the refractory lining. The CFD model was used to assess whether the predicted areas of high refractory wear could be minimized through changes burden geometry. The results showed that shape of the burden geometry greatly affected the overall flow patterns and heat transfer within the furnace.

By Dengfu Chen, Mujun Long, Youguang Ma, Xin Xie, Xing Zhang, Leilei Zhang

"Processing parameters of a submerged entry nozzle (SEN) affect significantly on the patterns of fluid flow and temperature distribution in beam blank continuous casting mold with double SEN s. Effect of the geometry structure and immersion depth of double SEN s on the fluid flow in beam blank continuous casting mold was studied by water modeling. Results showed that, the optimal nozzle inner diameter was 40mm, and immersion depth was 70-90mm. The mold surface fluctuation, slag distribution, impact depth and removing rate of inclusion particles were discussed under different processing parameters of double SENs. As the results indicated, slag distribution was more non-homogeneous with a higher casting speed. The results provided basic data for the design and optimization of SENs used in beam blank continuous casting mold.IntroductionNear-net-shape casting has the distinct advantages of less rolling procedures, higher metal recovery and lower energy cost. Therefore, in the recent decades, one of the recent trends in the steel making process is moving toward near net shape casting. in which beam blank casting is a typical technology. The schematic section of beam blank is shown in Fig 1."

Jan 1, 2014

By H. Kaffash

Ferromanganese is a ferroalloy with high manganese content which finds many uses for example as deoxidizer in steelmaking industry. However, there is very little data on the dissolution rate of carbonaceous materials in Mn containing metals. In this paper, the kinetic analysis of carburization reactions is investigated for Mn–Fe alloys. Dissolution rate of graphite in pure iron and four different alloys with 10 wt%, 40 wt%, 60 wt% and 85 wt% manganese at 1823 K was studied. Results showed that the dissolution rate of carbon from graphite increased with increasing time for all alloys. The dissolution rate constant increased with the increasing manganese content from 6.5 × 10−3 cm/s for 0%Mn to 23.6 × 10−3 cm/s for 85%Mn.

By Stein Tore Johansen, Fionn Iversen, Jon Arne Bakken

"A new marker chain front tracking method is used for modelling the meniscus movement during DC casting of aluminium ingots. Modifications have been made to an earlier method developed by Popinet and Zaleski [12] to adapt the model for simulations of meniscus dynamics in the casting process.Initial casting simulations show that wetting conditions in the mould greatly influence the meniscus stability. Controlling the wetting conditions seems to be important for improving the cast ingot surface quality.IntroductionIn conventional direct chill (DC) hot top casting of aluminium extrusion ingot with gas-slip poor surface quality of the cast ingot can be a problem. In the worst cases pronounced surface wrinkling occurs coupled with periodic zones of reduced grain size, macrosegregation and exudation at the surface. The observed surface irregularities are believed to be linked to Periodic surface oscillations or folding of the meniscus resulting in varying solidification conditions.The focus of this work is to gain a better understanding of the dynamics of the meniscus and the influence it has on the finished cast ingot surface through numerical simulations of meniscus movement during the casting process.A two phase marker chain front tracking technique[12] using cubic spline surface reconstruction is applied for modelling the meniscus movement. The advantage of this type of model is its accuracy in the calculation of surface tension forces. Also the wetting can be implemented directly as a boundary condition on the surface spline function. The method is applied in the FLUENT solver, which is based on a finite volume method using the SIMPLE algorithm."

Jan 1, 2001

By Wei Liu

A new process for extracting cadmium from the electric precipitated dust produced by ISP process was studied. A leaching rate of 89.1% of cadmium was attained by leaching the dust with NH3?H2O-(NH4)2SO4 system under the best leaching conditions: ratio of liquid to solid(l:s)=2.5, c(NH3):c(NH4+)=3:5, total concentration of ammonium and ammonia=8 mol?L-1, leaching time= 1.5h, temperature=35. The most troublesome impurity of lead could be deposited from the leached out solution automatically after put it static more than 15h when the total concentration of zinc and cadmium was up to 45gL-1 , and the final concentration of lead was 0.0047 gL-1, which meant 99% of it was removed. Metallic cadmium which contained cadmium more than 99% was prepared by electrowinning under the conditions: current density=750Am-2, total concentration of Cd2+ and Zn2+>25gL-1. The current efficiency was about 87% and the energy consumption for every ton of cadmium was about 548KWht-1. Main impurities of the metallic cadmium were copper and zinc and all of they could be got rid of in the following pyrometallurgical refining step.

Jan 1, 2006