Search Documents

By J. J. Kim

In a study of buildup in a green-feed reverberatory furnace, it was determined that approximately half of the crucible area has a moderate buildup of 25 in. or less, and that the area extending 45 f t from the burner end of the furnace has only a slight buildup. The false bottom, averaging 6 in. in thickness, was found to cover the entire crucible area. The stratification of Cr2O3, A12O3, and SiO2 occurs throughout the slag layer; this phenomenon is the principal reason for the formation of the false bottom in the green-feed reverberatory furnace. The false bottom is caused primarily by the settling of FeO*(A1,Cr),03 aggregates, which are derived mainly from returned converter slag. The false bottom can be transformed to a solid permanent buildup in the furnace, particularly when the matte is completely withdrawn. From the material balance of Al2O3 and Cr2O3 around the furnace, It is estimated that the average rate of aluminum chromite accumulation is approximately 0.3 ton per day or less.

Jan 1, 1976

By Batric Pesic

The interactions of mineral-pyrite with T. ferrooxidans were studied by using a cyclic voltametry technique. The interactions with bacteria were carefully examined during the entire growth stage of bacteria (fermentation). Several very important discoveries were made. For example, the pyrite surface invariably drastically changed its properties at the second day of fermentation. Beyond two days of fermentation, the cyclic voltamograms were insensitive to convective diffusion produced by stirring. The SEM study revealed that bacteria populated the pyrite surface at an extremely high density levels. The high density of bacteria, and the solid reaction products formed on the pyrite surface created conditions for pore diffusion which explained why the CVs became insensitive to convective diffusion in solution (stirring).

Jan 1, 1990

By K. B. McTaggart, G. Owusu, P. J. Merrin

"This study was conducted at Hudson Bay Mining and Smelting's zinc electrowinning tankhouse to determine the effects of varying levels of antimony and continuous gelatin addition on current efficiency. The levels of antimony and gelatin were varied from 0.012 to 0.030 mg/l and 0 to 10 mg/ll2 • 31 respectively, based on neutral ZnS04 electrolyte. A non-linear mathematical model relating current efficiency with antimony and gelatin was produced. The optimum operating point for gelatin was 6.5 mg/l. On the other hand the current efficiency increased with decreasing antimony levels. An interaction term between gelatin and antimony is present but is not significant enough to improve the ability of the tankhouse to handle purification upsets in antimony. Individually, the current efficiency was linear (decreasing) with antimony, and parabolic with gelatin concentration. However, at low antimony concentrations stripping of the cathode sheet was difficult. IntroductionThe zinc electrowinning tankhouse at Hudson Bay Mining and Smelting was designed in the 1930's and consists of 120 rows with each row containing ten cells. This system cascades acid from cell to cell In a row, with neutral zinc sulphate solution added to each cell through manually controlled spigots. Animal glue additions are made manually three times per day by operations personnel. The problem with this type of cell design and operation is that feed solution flows and composition can vary from cell to cell and from row to row due to the large number of manual control points. A new system which reduces the number of manual control points was designed and tested to determine if improvement in control of cell conditions would affect current efficiency. This system mixes spent acid, neutral ZnS04 electrolyte and reagents (gelatin, antimony and strontium carbonate) in a separate mix tank, ensuring that all cells receive a uniform feed solution. Gelatin was used in the test system instead of animal glue (which is presently used) because of the poor solubility and supply of industrial animal glue. The study reported here is the first in a series of experiments designed to justify the need to modify the present cascading cell feed system (Figure 1) to the proposed feed system (figure 2)."

Jan 1, 1997

By Luis W. Pommier

Large quantities of sea sludge containing halogenated organic compounds, such as PCB, oils and metals like arsenic and lead have accumulated throughout the years at the bottom of sea channels and harbors and are obstructing navigation and creating environmental problems which need to be resolved. A sludge from a California port would be dredged by suction pumps, it would be processed in a plant which would be built either on firm soil or on floating platforms. The sludge shows contents of up to 1 ppm of PCB, 15 % oil and 10 ppm of arsenic, which generates a very fetid odor. Bench scale work indicates that most of the contamination concentrates on the solid phase, in fact, only minor amounts of oil report to the sea water and can be readily removed by physical means. After separation of the sea water from the solids of the sludge by decantation, it is possible to solubilize the PCB, the oil and the metals into an organic solvent leaving a non-hazardous soil for disposal near the harbor. The PCB is dehalogenated during the solubilization process leaving a liquor solution containing the oil and metals. The oil is extracted leaving an aqueous solution containing the arsenic. Further process extracts the arsenic from this solution rendering the liquid non-hazardous. Transportation and disposal of the sludge is impractical. There are hundreds of thousands of tons of hazardous soils accumulated in each harbor, which would fill the hazardous waste disposal sites available and it would be, prohibitively expensive to do so. It is not possible to compare the costs of decontamination with a competitive method. If it were, the proposed process would be less expensive than transportation and disposal and it has the advantage of removing the liabilities from the Responsible party. After a full scale continuous pilot project is run to decontaminate a small, 500 cubic yards accumulation of this type of sludge in a California harbor, a full scale environmental project would be initiated. The decontamination of one million tons of sludge would be completed in five years.

Jan 1, 1995

By B. J. Jody

Each year, about 11 million tons of metals (ferrous and nonferrous) are recovered in the U.S. from about 10 million discarded automobiles. The recovered metals account for about 75% of the total weight of the discarded vehicles. The balance of the material or shredder residue, which amounts to about 3 million tons annually, is currently landfilled. The residue contains a diversity of potentially recyclable materials, including polyurethane foams, iron oxides, and certain thermoplastics. This paper discusses a process under development at Argonne National Laboratory to separate and recover the recyclable materials from this waste stream. The process consists essentially of two- stages. First, a physical separation is used to recover the foams and the metal oxides, followed by a chemical process to extract certain thermoplastics. The status of the technology is discussed, and the process economics are reviewed.

Jan 1, 1994

By Minjun Tang, Jianfeng Zhou, Linjiang Qing, Yufeng Guo, Tao Jiang

"For the comprehensive recovery ofV, Ti, Fe in vanadium-titanium magnetite in the process of pre-reduction-electric furnace smelting, it is expected that vanadium oxide is reduced into molten iron and titanium oxide is available in the slag. Thus the effect of slag basicity, the content of MgO, MnO and CaF 2 of slag content on the separation of slag and molten iron and the comprehensive recovery of V, Ti, Fe were investigated. The results show that increasing slag basicity, MgO, MnO and CaF2 are all beneficial to the separation of slag and molten iron. Higher slag basicity and the addition of CaF2 strengthen the reduction of vanadium oxide, and inhibite the reduction of titanium oxide, which are in favour of the recovery ofV and Ti. However, the addition ofMgO, MnO was not efficient for the comprehensive recovery ofV, Ti, Fe. For the vanadium-titanium magnetite of Panxi in China, the recovery of Fe was over 98%, the recovery ofV in molten iron was over 85% and the Ti02 content in slag was about 43% under the optimal conditions of slag phase type.IntroductionIt is well known that there are abundant vanadium-titanium magnetite resources which are located in Panzhihua of Sichuan Province[!]. At present the vananium-titanium magnetite concentrates are smelted in the blast furnace, which just make use of iron and vanadium, but lots of titanium is discarded in the slag. At the same time, the process has a large number of disadvantages, such as low recovery of vanadium, long route, pollutions, large investment and expenditure of energy[2-3]. In recent years, in order to efficiently utilize the vanadium-titanium magnetite concentrates, several new non-blast furnace processes have been proposed, such as pre-reduction-electric furnace, pre-reduction-grinding separation and so on[4]. Especially pre-reduction-electric furnace is operating well in South Africa and New Zealand,However,Du to the high slag basicity of the slag, the grade ofTi02 of slag is Corresponding author:Minjun Tang.E-mail:450435123@qq.com. Tel:13627429224."

Jan 1, 2013

By Emilia Visileanu, Eftalea Carpus

"Ecological economic policy shall be understood as the sum of political, economical and environmental measurements aimed at the entire economy dematerialization and the dematerialization shall be ""imposed"" since the designing stage of goods and services"". European textile and clothing industry with a long leading tradition in terms of innovation, fashion and creativity, continues to be one of Europe's major industrial sectors. Textile industry affects the environment by high consumption of water, energy and chemicals, as well as by the large amount of waste it generates as a result of using a large number of chemicals and technological processes.Textile waste prevention, reduction and ecological exploitation require the implementation of new management and education tools.Introduction“Europe must learn from the experience of global economic and financial crisis ""- this was the conclusion of the European Commission that has elaborated a ten-year strategy designed to reinvigorate the economy and make possible a growth which is ""intelligent, sustainable and favorable to inclusion"", by a better coordination of national and European policies.Adapting infrastructure and logistics that encourage the marketing of ""sustainable"", ""fair traded"" and ""green"" products as well as other special „green” products will facilitate the movement towards dematerialization and eco-efficiency among producers."

Jan 1, 2012

By Michael Sheedy

Recoflo® ion exchange technology utilizes fine mesh resin beads, a fully packed resin bed, and counter-current regeneration. These unique features help to improve exchange kinetics, reduce regenerant consumption, and increase the concentration of strip solutions. Commercially, Recoflo technology has been extensively used in the following areas: the separation of strong mineral acids from dissolved metal salts, the purification, removal and recycle of dissolved metals in the surface finishing industries, and the production of high purity water. In the mining and metallurgical industries Recoflo ion exchange systems have been installed to treat a copper refinery bleed stream at Falconbridge's Kidd Creek plant and to treat a nickel and cobalt bearing ammonium sulfate effluent stream at another primary metal producer's facility. In the first application an APU® Recoflo system is used to separate the sulfuric acid at 200g/L from the dissolved copper and nickel sulfate salts at 80 g/L. The absorbed sulfuric acid is recovered from the resin by elution with water and is then returned to the refinery electrolyte circuit. In the second application a chelating ion exchange resin is used to remove nickel and cobalt at 0.01 - 3.0 g/L from process streams containing 120 - 240 g/L ammonium sulfate. This Recoflo system has been designed to reduce the nickel and cobalt levels to 0.001 - 0.002 g/L while recovering cobalt and nickel at concentrations up to 30 g/L and 15 g/L respectively. Case studies for both these metallurgical applications and other Recoflo processes are presented in this paper.

Jan 1, 1998

By T. T. Chen

Gold in the Twin Creeks ore is primarily associated with arsenian pyrite. During pressure oxidation, the sulphides are solubilized, but part of the dissolved iron reprecipitates as jarosite and as an iron sulphate-arsenate-phosphate phase. The pressure oxidation products are subjected to cyanide leaching. The cyanide leach residues consist of quartz, gypsum, bassanite, anhydrite, small amounts of jarosite, an iron-sulphate-arsenate-phosphate phase, as well as trace amounts of orthoclase, rutile, pyrite, hematite and monazite; all these particles are dispersed in a fine grained matrix of illite-muscovite. The autoclave leach residues contain a small amount of carbonaceous matter. Many gold grains are detected on the surfaces of the carbon particles, and these gold particles are not leached during cyanidation. The gold particles are typically 0.1-0.2/Lm in size and commonly are embedded in the carbon surface or are coated with a K-AI-Si-S-O phase on the surface of the carbon. The gold grains are consistently associated with elevated CI contents (50-300 ppm Cl). The poor gold cyanide leach recoveries, which initially occurred in the Twin Creek developmental circuit under certain operating conditions, are attributed to the presence of chloride in the feed. This results in the formation of soluble gold chlorocomplexes in the autolcave and the subsequent sequestering of the gold on the surfaces of the carbon particles.

Jan 1, 2000

By Moelans. N.

A method using an ex-situ electrochemical measurement device was developed to determine the oxygen potential of non-ferrous metallurgical slags. The electrochemical cell consists of the molten slag sample, an inert Ir electrode, a stabilized Zr02 solid electrolyte and a NilNiO reference electrode. Different slags from non-ferrous pyrometallurgical processes were analysed at I 100 and 1200 °C and pO2values between 10-3 and 10-12 bar were obtained. The measurements were evaluated with thermodynamic calculations and using processing considerations. It was found that the reproducibility and stability of the measurement was significantly improved by shielding the molten slag from the atmosphere by a thin layer of carbon, especially for slags with a low oxygen potential.

Jan 1, 2003

By Osamu Iida

Since 'start-up of the larger Mitsubishi Continuous Copper Smelting Process in 1991, furnace relining campaign was gradually prolonged to once every 2 years according to deregulation of governmental boiler inspection. On the other hand, in 1998 Naoshima smelter embarked on an intermediate strategic expansion plan to strengthell its international competitiveness. As part of this plan, modifications were implemented in the copper smelter designed to increase output of anodes from new charge source to 270,000 tpa. In May 1998, treatment of dried neutralized residue was started in C furnace, and during the shutdown for brick relining in April 1999, intensive modifications to the boilers as well as the installation of new spray coolers for furnace off gas treatment were implemented. Finally, the new larger oxygen plant was commenced its operation in May 2000 and the expansion was achieved around 30% increase of anode production from original design.

Jan 1, 2001

By Saeid Pournaderi, Ahmet Geveci, Ender Keskinkilic, Yavuz A. Topkaya

There are mainly three commercial nickel laterites in Turkey: Gordes, Caldag and Sivrihisar. The first two appear in Western Anatolia. The third one, Sivrihisar (Yunusemre) laterites have been found in the first decade of the millennium, in the Central Anatolia region of Turkey. Since then, mining facilities have been continued in Yunusemre. Calcination, prereduction and smelting of Sivrihisar laterites have been extensively studied and published. In the current work, some results of the studies related to characterization of Sivrihisar laterites will be presented.

Jan 1, 2016

By E. Fregeau-Wu

The mineralogy and grain size distribution of phases in a steelmaking slag and experimental products from the heating of the slag under various conditions were determined to explore the possibility of recycling of the iron and manganese to the blast furnace. The steelmaking slags consisted of three major phases: dicalcium silicate, dicalcium ferrite, and Mg-Mn-wustite. Most of the phosphorus was contained in the dicalcium silicate and to lesser extent in the dicalcium ferrite. Due to the fine grain size of the dicalcium silicate, grinding and magnetic separation required pretreatment to increase the grain size and hence the liberation. Experiments on a steelmaking slag were conducted by heating the slag to 1633-1748°K( and slow-cooling in an inert atmosphere at various rates with or without the addition of fluorspar (CaF2) as a flux. Grain size distribution analyses of the starting material and the slow-cooled products were performed using the SEM-IPP area scan method and the QEM*SEM linear scan method. Comparable and reproducible results were obtained on the same sample using both methods. A size versus volume percent plot showed the increased grain growth most effectively. Examples of the grain size distributions obtained were used to show that a higher soaking temperature prior to slow-cooling, a slower cooling rate, and the addition of fluorspar to the slag promoted grain growth.

Jan 1, 1989

By Vinod K. Namilakonda

In situ synthesis of discontinuously reinforced aluminum alloy metal matrix composites was investigated. Aluminum alloy (A356: Al-7 wt% Si) was reinforced with dispersed AlN particles. Thermodynamic calculations were made for the composition determination of various phases formed during bubbling of NH3 gas into the Al alloy melts in the temperature range 1173-1473 K. Experiments were carried out for in situ production of AlN particles with the reaction between Al melt and NH3 gas in high temperature resistance furnace at 1473 K. The products were characterized using SEM, EDS and XRD. Effect of bubbling time of NH3 gas on the AlN formed in the composites was studied. The amount of AlN reinforcement in the Al alloy composites was observed to be in the range of 5 to 35 wt%. Good agreement was observed between the experimental and thermodynamic calculated data on the composition of AlN in Al alloy composites.

Jan 1, 2006

By M. S. Moats

Galvanic stripping, in conjunction with solvent extraction, has been proposed as a technical option to the challenging problem of iron removal in certain hydrometallurgical processes. The galvanic stripping process is based on the ability of a solid metal to directly reduce ferric ion to the ferrous state in an organic media. Stripping the iron into the aqueous phase is then easily accomplished. Previous work has shown the reaction kinetics and efficiency are affected by such operating parameters as water and oxygen contents, temperature, time and metal reductant. In this study, the optimum operating range for some of these variables was determined. Both zinc and iron metal were used in the separate stripping of iron from D2EHP A. Reasons for the differences in the extent of the reaction obtained using the various conditions are discussed.

Jan 1, 1996

By Hong Yong Sohn, Miguel Olivas-Martinez

"Different approaches are used for calculating the ‘energy requirement’ of a process. The determination of energy requirement becomes confusing for a process in which a fuel is also a reactant. The key issue is which heat of chemical reaction should be included in the ‘energy requirement’ value. We will use the example of ironmaking processes to illustrate the problem. The different approaches essentially boil down to the question: does one include the combustion heat of the reductant used in the reduction reaction or just the heat of the reduction reaction? Depending on the viewpoint, either approach can be accepted; it is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of a process depends on the choice. The energy requirement of a novel flash ironmaking process will be compared with that of an average blast furnace operation.IntroductionDifferent approaches are used for performing energy balance calculations and perhaps more significantly in presenting the ‘energy requirement’ of a process. The question becomes more involved for a process in which one or more reactants are also used to generate the process heat by combustion. Often the key issue is which heat of chemical reaction to include in presenting the ‘energy requirement’ of the process.It is worthwhile to note at the outset that the difference in energy requirements between different processes for converting similar raw materials to the same desired product is largely unaffected by the choice of chemical reactions to be included. However, the absolute value presented as the ‘energy requirement’ of a process can be different by a large amount depending on the approach. We use the example of ironmaking processes to illustrate the problem. In these processes, as currently practiced or under development, carbon and/or hydrocarbons (including hydrogen) are used as the fuel as well as the reactant for reducing the iron oxide mineral.The different approaches in this case essentially boil down to the following question: does one include the combustion heat of the reductant used in the reduction reaction or treat the reductant portion as just a reactant? Depending on the viewpoint, either approach can be considered acceptable. It is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of an ironmaking process (e.g., the currently dominant blast furnace process) depends on such a choice. It is particularly important to clearly state the specific approach used when the energy requirement of ironmaking is compared with those of other industrial processes such as petrochemicals production."

Jan 1, 2014

By Sarah Beutner Mavrogenes

The mineralogy of three slags from a domestic secondary copper refinery were studied by applied mineralogical techniques to determine the: 1) phases present, 2) phase chemistry, 3) phase abundance, 4) associations, 5) crystalline habit, 6) grain size, 7)microtextures, and 8) causes for certain metallurgical problems, such as metal losses to the slags. The slags were produced by skimming the bath prior to melt-down to allow heat from the flame to reach the bath. The first slag is highly viscous and all three slags contain a large amount of copper. The "first slag", which is skimmed prior to treatment of the bath with fluxes, contains metallic copper, cuprite, delafossite, magnetite, Mg-hercynite, common spinel-chromite solid solution, picrochromite-chromite solid solution, common spinel-picrochromite solid soiution, gahnite, cassiterite, silica-rich glass, and corundum. Its abundant solid refractory phases make the slag difficult to skim. The "soda-rich slag", skimmed after the treatment of the bath with sodium carbonate flux, contains cuprite, delafossite, magnetite, cassiterite, Na-Al-silicate, and Na-Al-Ca-silicate. It contains less metallic copper than the first slag and lacks the refractory minerals. The "phosphorus-rich slag", skimmed after treatment of the bath with a copper phosphide flUX, contains metallic copper, cuprite, delafossite, berlinite, cassiterite, silica, apatite, Cu-Fe-rich apatite, copper phosphate, Cu-Fe-phosphate, and a Pb-phosphate. In contrast to the above three copper-rich slags, recent charges have produced a silver-copper-rich slag. The "silver-rich slag", skimmed after the treatment of the bath with a copper phosphor ide-borax flux, contains, cassiterite, delafossite, cuprite, a Na-Al-silicate, magnetite, metallic copper, MgO, common spinel-chromite solid solution, and wollastonite. Silver ranging from 0.05 to 2.02% was found by atomic absorption and inductively coupled plasma spectrometry analyses in the metallic copper phase.

Jan 1, 1989

By William Petrul

Image analysis studies were performed on mill products from laboratory flotation tests of the Zn-Pb ore from the Faro deposit in Yukon, Canada, to determine mineral liberations at specific grinds and to predict recoveries at optimum flotation conditions. The minimum and optimum grinds for liberating sphalerite and galena were predicted from size analysis data for the minerals in large ore pieces, and determined by image analysis studies of the mill products. The determined optimum grinds are about 2 Tyler mesh sizes larger than predicted because sane of the fine grained sphalerite and galena occurs in interstices between coarser grained pyrite and is liberated when the pyrite grains are broken apart. Materials balance calculations were performed on the analyzed values for the liberated and unliberated sphalerite and galenaa to determine their distributions in the mill products. The laboratory flotation tests recovered 74% of the sphalerite and 83% of the galena in Zn and Pb concentrates respectively. The mineral evaluation study indicates that the optimum recovery for sphalerite and galena are 85 and 83% respectively. The company is currently recovering 80% 'of the sphalerite and 82% of the galena.

Jan 1, 1989

By Yoshisada Michiura, Junko Umeda, Katsuyoshi Kondoh

Rice husks or straws, one of the main agricultural wastes in South-east Asia, have a large possibility to be employed as usefully renewable resources to produce energy and high-purity silica (SiO2), because they consist of about 70% organics such as cellulose or hemi-cellulose, and 20% amorphous SiO2. The former is utilized as bio-mass energy; for example, thermal or electric energy, and bio-mass ethanol. High-purity silica can be used as raw materials in the industrial uses. It would be possible to extract silica elements from rice husks and straws by burning them in air because their main contents are organics. In the previous studies, a strong acid leaching treatment on rice husks before burning was carried out by using H2SO4, HCl and HNO3 to prepare high-purity silica materials. This was available to accelerate the hydrolysis of celluloses and hemicelluloses contained in rice husks, and remove the above metallic impurities. A strong acid leaching treatment, however, is significantly hazardous to environment and human life, and causes an increase of the process cost. In this study, the environmentally benign, harmless to human and economically effective process to produce high-purity amorphous SiO2 materials from rice husks has been established without using strong acids. From a viewpoint of the harmless influence on human body, the carboxylic acids were used in the leaching treatment on rice husks. TG-DTA measurement and GCMS analysis indicated that the leaching was effective for the hydrolysis of celluloses and hemicelluloses contained in rice husks at 473K~873K, which produced the same results in using the conventional sulfuric acid. The metallic impurities could be also removed from the husks via a chelate reaction between carboxyl groups (-COOH) and the metal elements. In particular, it was clarified that cadmium (Cd) were completely removed from rice straws by this reaction. Concerning the burning conditions of rice husks after the acid leaching, it was necessary to supply a suitable amount of air to completely combust organics; for example it required air supplement of 50 ml/min. or more. The burning temperature should be less than 1273K to obtain amorphous structured silica. High-purity amorphous silica materials with 99% or more were prepared from rich husks by applying the citric acid leaching treatment and burning process at 1073K in air.

Jan 1, 2008

By Milton Blander

A review of concepts and theories for predicting thermodynamic solution properties of multi- component high temperature liquid solutions is reviewed. During the last 50 years the ability to predict :such properties for molten salts, silicates and metals based on the generally known properties of the lower order (often binary) systems has been developed and shown to provide predictions which are quite useful in science and technology. There are many gaps in our understanding of these high temperature solutions, especially for metals, and considerably more work is needed.

Jan 1, 1996