Search Documents

By Regina Maria Pinheiro

This work has for objectives to characterize a waste generated in the form of sludge during the treatment of the effluent of a paper making industry and to evaluate the effect of its incorporation in the amount of 10 wt.% on the properties and microstructure of a clayey body used for brick production. For the characterization of the waste the following techniques were used: X-ray diffraction, X-ray fluorescence, differential thermal analysis and termogravimetric analysis. Incorporated bricks were produced in industrial scale before firing at 750°C in a Modified Caieira type furnace. The physical and mechanical properties evaluated were water absorption and compression strength. The microstructure of the fired ceramic was evaluated by optical microscopy. The environmental evaluation was made by solution test and atmospheric emission by monitoring the release of SO2, NOx and particulate material. The results showed that, in agreement with the characteristics of the waste, its recycling into red ceramic can contribute to decrease the consumption of fuel during the firing stage. The properties of the fired ceramic attend the norms. With respect to the environmental aspect, the incorporation of the waste did not impact the environment.

Jan 1, 2009

By S. Uddin

An integrated device has been developed to measure sedimentation potential, conductivity and pH simultaneously of particulate systems. Maxwell?s model was used to calculate volume fraction of solid from the conductivity data. In this approach, all system variables are known and zeta potential can be calculated from Smoluchowski?s equation. The technique is validated by comparing zeta potential vs. pH for alumina and silica suspensions with electrophoresis measurements. The technique was extended to mixed alumina/silica systems. Sufficient column height along with size difference between the two minerals allowed gravity fractionation during settling. Sedimentation potential measured over time identified the transition from one mineral to the next. Using XRD analysis the results supported the correlation between surface charge and sample composition. This is a step towards characterizing surface charge of mixed systems of interest in mineral processing.

Jan 1, 2010

By Yufeng Guo

Mineralogy and physico-chemical characteristics of a nickel hydrometallurgical residue and recovery of iron-bearing minerals by flocculation-magnetic separation were studied. The results show that the nickel residue is super-fine and fraction less than 0.045mm reaches 85.4%. Ferrous minerals are chiefly magnetite and ferruginous glass. Magnetite accounts for 31.7% and exists as free magnetite. Ferruginous glass is of multicomponent amorphous substances with low-iron grade but strong magnetism, and accounts for 39.9% of total iron minerals. Addition of flocculants increases granularity and magnetic force of fine iron-bearing particles and improves iron grade and recovery. The tests with flocculation separation show that a concentrate assaying 56.68% Fe with 81.72% recovery was obtained in a magnetic tube. A concentrate with 56.92% iron grade and 67.96% recovery was obtained by flocculation-magnetic separation with a magnetic cylinder.

Jan 1, 2006

A sinter plant baghouse dust has been treated as a hazardous solid waste, and disposed at a very high price. A series of leaching tests were conducted to examine the possibility to produce high grade potassium chloride from the solid waste. It is found that around 40% of the solid wastes can dissolve into water, and a deposit with more than 90% KCl can be produced after simply drying the solution.

Jan 1, 2009

By Sergio N. Monteiro

Jute fiber reinforced polymer composites are among the most investigated and applied natural composites. In this past decade the mechanical properties of these composites has been assessed for various types of test conditions. However, the reported results correspond mainly to short-cut jute fiber composites, which do not present the highest mechanical strength as compared to continuous fibers of the same kind. In order to complement these results, the present work evaluated the mechanical behavior, by means of flexural tests, of polyester matrix composites reinforced with continuous jute fibers. Bend tests were conducted in standard specimens with up to 40% of jute. Fracture analysis by SEM displayed the rupture mechanisms. The results showed an improvement in some flexural properties with incorporation of jute fiber. However, a low fiber/matrix interfacial stress was responsible for limitation in the values attained by some properties.

Jan 1, 2010

By Elisa Alonso

Manufacturing firms that rely on finite resources have a stake in ensuring sustainable materials use. Higher material prices and uncertain material supply, consequences associated with scarcity, can be damaging to firms. Firms have a number of options to improve material sustainability including dematerialization, material substitution and recycling. However, these options require technological capability, capital investments and supply-chain infrastructure; firms may decide to make such investments only if material prices increase. Once decisions are made, the barriers and delays to implementing changes may harm firms. The impact of not reacting to changes in material supply on firms was examined for the case of different platinum-using industries. It was found that taking action is particularly important for firms when limited material availability leads to volatile market conditions. Industries can benefit especially if they ensure process flexibility and have options for changing their material use patterns.

Jan 1, 2010

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By María Cristina Ruiz

Enargite rich copper concentrates can not be treated by conventional smelting/converting technology and thus nonconventional methods such as leaching must be used. Since enargite (Cu3AsS4) is a hard to dissolve mineral in acidic solutions, pyrite, a common impurity in copper concentrates, could be used to increase the enargite dissolution rate. On this matter, we present in this work experimental data on the pressure leaching of a mixed enargite-pyrite concentrate in H2SO4-O2. The results show that the dissolution of enargite from the mixed concentrate is considerably faster than the dissolution of pure enargite mineral. The leaching rate increases significantly with temperature. Over 98% of enargite was dissolved in leaching 64 micron size particles at 200 ºC and 100 psi of partial pressure of oxygen in just 30 minutes. A change in the partial pressure of oxygen from 50 to 150 psi showed also a large influence in the leaching rate.

Jan 1, 2010

By Jinhui Li

Silver is a very important metal used in a wide range of applications. It is necessary to recovery of Ag from electronic wastes for increasing of Ag price and circumstance protection. For separating and recycling Ag from Ag-Cu composite materials, thermodynamic data of reaction is calculated and some experiments have been proceeded with Ag-Cu composite material scraps, time, temperature, nitric-sulfuric mixed acid volume ratio and the volume ration of mixed acid vs. water have been discussed. The results show that the optimization conditions is that nitric-sulfuric mixed acid volume ratio 5:95, volume ratio of mixed acid vs. water 10:1, temperature 55?, time 25min. In the conditions, Ag can be selectively leached from Cu-based composite material, Cu base is not eroded nearly.

Jan 1, 2009

By Viviane Tavares

The technology advance of mobile devices makes consumers of these equipment do more constant exchanges, with this the obsolete devices discarding becomes an environmental problem, due its landfill accumulation. In order to minimize the environmental impacts caused by these equipment there?s the recycling necessity of polymers, ceramic and metallic materials. The main goal of this recycling is to study the printed circuit board of device mobile processing through ore treatment in order to recoup copper. Initially printed circuit boards were processed in a knives mill, in order to liberate the ferrous material, after that it was done the magnetic separation of the reduced residue. With the not magnetic fraction it was done the grain sized analysis and sulfuric acid and hydrogen peroxide leaching analysis. With the chemical analysis results proceeding from the leaching aliquot it was possible to observe that the leaching method with sulfuric acid and hydrogen peroxide presented greater copper recovery.

Jan 1, 2009

By J. C. Pandey

The paper highlights the experimental investigations to characterize texture and plastic strain ratio r-Bar in auto grade steel sheets by ultrasonic measurements, whereas attempts were made to characterize interlamellar spacings in pearlite, tensile stresses and torsional properties in prestressed concrete wires by eddy current measurements. Good correlations were obtained between the testing parameters (such as ultrasonic attenuation and velocity in case of steel sheets as well as eddy current out put voltage and phase angle in case of steel wires) and the materials properties (such as texture, plastic strain ratio r-Bar, interlamellar spacings in pearlite, tensile stresses and torsional properties). 15 MHz normal direct contact and 20 MHz delay line normal shear wave probes were used for ultrasonic measurements. Eddy current measurements were done using an absolute coil probe with variable frequency selection. The experimental results show the possibility of nondestructive on line measurement of the above microstructures and properties.

Jan 1, 2010

By Xingjian Gao

The mechanical properties of a low carbon low alloy steel in the austenite and _-ferrite regions have been examined by thermal-tensile tests using a Gleeble-1500D system at temperatures in the range 600oC to 1300oC and at a strain rate of 10-3/s; these being the conditions that apply to the unbending operation during the continuous casting of steel. The yield strength and tensile strength of steel decreased with increasing test temperature and the embrittlement zone occurred in the temperature range 800oC to 970oC. In the embrittlement zone, the fracture surfaces and microstructures of the tensile specimens were examined by scanning electron microscope. The results showed that the cause of the embrittlement at 950oC in which the minimum %R of A was around 36% is the second phase particles precipitated along the _ grain boundary during deformation leading to inter-granular brittle fracture.

Jan 1, 2010

By Raj P. Singh Gaur

Due to high concentration of NaOH in the digested slurry after scheelite digestion, it is diluted to about 4N before filtration to separate sodium tungstate solution from the sludge (residue). However, in practice there may be deviations in the normality of NaOH present in the slurry. There may also be variations in the temperature of the slurry and filtration time. Slight variations in these parameters could cause tungsten losses in the sludge via the back reaction: Ca(OH)2 + Na2WO4? CaWO4 + 2NaOH This paper pertains to the effect of normality, temperature and time on the tungsten losses in the sludge that is separated from ?diluted-scheelite-slurry-in-NaOH? via filtration. Results indicated that tungsten losses in the filtered residue (sludge) were quite significant when the slurry temperature was kept at 70°C or higher. The effect of high temperature was less significant at the slurry normality of 3.6 or higher. Combination of low slurry normality (<3.6) and high temperature (>60°C) resulted into large W-losses in the sludge.

Jan 1, 2006

By S. B. Johnson

Keywords: Spray, Aluminum, Simulation A stochastic, droplet-resolved model has been developed to describe the behavior of a binary aluminum alloy spray during the spray-rolling process. In this process, a molten aluminum alloy is atomized and the resulting spray is deposited on the rolls of a twin-roll caster to produce aluminum strip. The one-way coupled spray model allows the prediction of spray characteristics such as enthalpy and solid fraction, and their distribution between the nozzle and the deposition surface. This paper outlines the model development and compares the predicted spray dynamics to PDI measurements performed in a controlled configuration. Predicted and measured droplet velocity and size distributions are presented for two points along the spray centerline along with predicted spray averaged specific enthalpy and solid fraction curves.

Jan 1, 2005

By Zhuokun Cao

Manufacture of aluminum foams still suffer from nonuniformity and poor reproductively for there is lack of basic knowledge of foaming process. In this paper, carbon fibers are used as novel stabilizing additive for aluminum foams, and the structure evolution of aluminum foams with different fiber content was studied. A laser rangefinder was used to detect the expansion rate of different al foams. Al foam samples are solidified at different foaming time to determine its relative density and cell size distribution. Results indicate that the cell size of foams linearly increases with the decrease of density, and the slope of the line is influenced by fiber content. The relationship between expansion ratio, density and cell size of the foams is discussed. It is concluded that the density of resulting foam is influenced by the rate of gravity driven drainage, and its cell size is determined by expansion ratio and foaming time.

Jan 1, 2010

By Yanjie Liang

Elemental sulfur and volatilization kiln slag(VKS)containing heavy-metal produced by smelter factories were used to produce sulfured building material. The effects of heating mode, material proportion (MSulfur:MVKS), size of waste particles and ratio of aggregate to filler(A/F) on the mechanical properties and leaching toxicities of solidified stuff were investigated. The optimal conditions for the solidification are stepped heating mode, 3:7 ratio of MSulfur to MVKS, particle size less than 150µm and 3/17 ratio of A/F. Under the above optimal conditions, the compressive strength of solidified stuff rises to 35 MPa, and water absorption is down to 4%-6%.Furthermore, when NaOH is applied as an additive in the process of solidification, the 2+concentrations of most heavy metals except Pb have reached the national leaching toxicity standard. The results of X-ray diffraction reveal that sulfured solidification is caused by the physical encapsulation rather than chemical transformation.

Jan 1, 2010

By Zeljka Pokrajcic

Crushing and grinding, or comminution, circuits are the most energy intensive process of a mineral processing plant. Comminution involves the physical size reduction of an orebody to a particle size sufficient for recovery of the mineral values. However, the comminution process remains inherently inefficient. The inefficiency is a result of the operating nature of comminution devices such as grinding mills, where transfer of energy between grinding media and particles in unconstrained and completely random. New comminution circuit design strategies are presented in this paper. The aim of the new strategies is to improve the overall efficiency of the comminution process and reduce the total energy consumption of a comminution circuit. The energy efficient strategies include the: ? rejection of coarse size liberated gangue from the comminution circuit and further downstream size reduction ? use of more efficient grinding and crushing equipment ? the selection of coarser particle product sizes to alleviate the increased energy intensity required to achieve finer product sizes Singularly and when combined, these energy efficient strategies can significantly decrease the overall energy consumption of a comminution circuit. This paper also explores the financial impact of certain energy efficient strategies using an analysis tool called EcoNomics?. It shows that substantial financial gains can be made by including more efficient technologies and methods in comminution circuit design.

Jan 1, 2010

By Carl W. Lam

The increased obsolescence rate of electronic products has made it evermore pertinent to understand the potential environmental impact of materials choices to help guide electronic waste (e-waste) management and promote awareness of high burden materials. Methods for screening for the performance of materials and their potential burden on human health and the environment can be used to comparatively select constituents of present and prospective electronic products. These methods should be able to yield more robust information when linked to other decision-making strategies where integrated data on consumer preferences, production quantities, and regulatory initiatives are sparse or unavailable. A framework is presented here for generating metrics of ecological toxicity, human health toxicity (cancer and non-cancer categories) and global resource consumption for evaluating environmental impact of materials (specifically metals) in electronic products. The time-dependent impact trends of United States? printed wiring board (PWB) metals usage, principally derive

Jan 1, 2010

By A. J. Rigby

Refractory linings in converters or anode furnaces used to over-oxidize the blister copper will suffer rapid deterioration, due to prolonged contact with copper oxide-rich slag. Nitrogen stirring with COP KIN porous plugs and use of SEMTECH OPC in converters and anode refining vessels can considerably reduce both refractory wear and processing times. In addition, careful control of the vessel atmosphere and the use of real-time optical process control minimize both slag volume and contact time with the vessel refractory.

Jan 1, 2005

By Karel Van Acker

The automotive is a sector where energy consumption during the use phase prevails over the production and the end-of-life phase. Therefore, a lot of research and innovations at replacing classical steel parts by lighter materials like light metals and polymer composites. While composites are very attractive for the use phase of cars, their introduction suffers from the limited end-of-life options for composite structures. An extensive life cycle analysis for a reference car design has been conducted to study the effects of replacement of conventional steel structures by lightweight carbon fibre composite alternatives. The study also takes second order effects in the design of the car into account. The opportunities and treats of the trend towards more intensive use of carbon-fibre composites in car design are identified. A discussion on the potential of other types of composites for the automotive in terms of sustainability considerations is added.

Jan 1, 2010