Search Documents

By B. Mishra

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite that is mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90 wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct. At this stage, the product could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. The mineralogical characteristics of the reduced product are not amenable to magnetic separation for iron recovery. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Special attention has been paid to lower the alkali content of the reduced material. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by an acid-leach process. This paper describes the successful efforts of iron and alumina recovery.

Jan 1, 2000

By Tao Zhang, Wen-tao YU, Hai-bin ZUO, Jian-Liang Zhang

Sintering-pot tests and metallurgical performances of sinter with 4 kind of different Al2O3 contents are experimented in this paper. Results show: when the Al2O3 contents increase from 2.0% to 3.5%, acicular calcium ferrites in mine phase will be gradually replaced by plate-like iron calcium. The increase of Al2O3 contents will lead to the addition of liquid viscosity and the reduction of permeability of sinter bed. Sintering time will be prolonged. The rate of yield is stable basically but production is low; besides, the increase of liquid viscosity will decrease of drum strength. The change of permeability of the material layer will make RDI +3.15 decrease first and then increase when Al2O3 contents changed from 2.0% to 3.5%. RI of sinter shows a contrary trend because many open voids are formed by deterioration of liquidity first and then pores closed.

Jan 1, 2015

By Kenneth S. Coley, Michael Pomeroy, Elaine Chen

Recent work on modeling of BOF steelmaking is reviewed, highlighting the critical aspects of each approach. It is concluded that the most successful models should be based on a deep understanding of the mechanisms and kinetics of the critical reactions. The importance of the decarburization mechanism is discussed with particular reference to its role in droplet swelling or bloating which has a profound influence on the droplet residence time in the slag. Conditions which cause bloating are discussed and the rate determining step is proposed to be primarily nucleation of CO bubbles inside the metal droplet with some influence from growth by reaction at the bubble/metal interface. The discrepancy in the super-saturation ratio required for classical nucleation is discussed and an approach using a surface tension modifying parameter is illustrated. Finally, the role of CO nucleation in controlling the driving force for dephosphorization is discussed.

Jan 1, 2014

By L. W. Beckstead

In a conventional zinc refinery plant, zinc concentrates were roasted at 950°C. The calcine was ground and leached in a series of leaching vessels using sulfuric acid. The pH in the first leaching vessel was maintained at 2.5, while the pH of the solution exiting the last vessel was about 5.4. The leached residue typically contained (in percent) 0.1 Ag, 0.2 As, 0.7 Cd, 2 Cu, 15 Fe, 10 Pb, and 15 Zn, and it was classified as hazardous material according to the EP-toxicity test. In order to make the residue non-hazardous, and to recover most of the metal values from the residue, a brine leach process was developed. The process consisted of leaching the zinc leach residue in CaCI, brine solution at pH 2 for 1 hour at 90°C. Silver extraction was about 95 percent, while lead, copper, cadmium, zinc, and iron extractions were about 80, 50, 50, 30, and less than 0.5 percent, respectively. More extreme conditions of acidity could have been used in the leaching stage to increase zinc dissolution, but iron dissolution would have significantly increased which would have complicated subsequent recovery steps. The leached and washed residue passed the EP-toxicity leach test and could be disposed as non-hazardous. Silver, copper, and lead in the leach solution were recovered by zinc cementation, while zinc and cadmium were recovered by sulfide precipitation. The resulting solution can be recycled in the process after magnesium precipitation.

Jan 1, 1993

By W. Kasprzak

Modern light metals processing technologies are very complex and involve a diverse set of variables that must be quantitatively evaluated. The most effective way to design new casting processes that deliver specified metallurgical and mechanical properties is to develop a method of simulating the "real-time" process within a test sample of sufficient size. The results can then be analyzed and the required optimizations can be performed. This paper presents a novel method of simulating the industrial casting processes in a laboratory environment using an experimental apparatus based on the principle of high frequency induction heating. The applicability and accuracy of the proposed analytical method is demonstrated, for example, by simulation of the solidification and heat treatment of a test sample composed of two dissimilar materials. The simulation can be used to develop a stress model for an engine block made from an aluminum based alloy with iron cylinder liner inserts.

Jan 1, 2002

By Mojtaba Ahmadiantehrani

A previous study showed that up to 80% gold extraction could be obtained with 160 lbs/ton hypochlorite consumption at ambient temperature from a low grade Carlin-type carbonaceous ore. Crushing the ore to a finer size and agglomerating with cement decreases hypochlorite consumption by 60%; while, agglomeration and curing the cement-ore mixture with hypochlorite solution has no significant effect on total gold extraction. The high hypochlorite consumption is due to oxygen depletion as the solution percolates through the column, i.e., oxidation of gangue materials. These side reactions are reduced at sub-ambient temperatures resulting in a substantial further decrease in hypochlorite consumption. The optimum temperature range and additional reduction of hypochlorite consumption by introducing the reagent into the column at different elevations will be discussed.

Jan 1, 1992

By Du Sichen, S. Seetharaman, A. Jakobsson

"In the Present paper, the principles of oxygen potential measurements have been discussed along with the design details for oxygen sensors that are used in copper industry. A description of some of commercial probes is presented along with their salient features. The application of these sensors in flash smelting, converter and casting sections of copper production are discussed along with their implications on process optimization.I. IntroductionThe high temperature galvanic cells have come into prominence on account of their numerous applications in both fundamental as well as applied measurements. Since the inception of the oxygen-ion conducting electrolytes like ZrOrCaO·by Kiukkola and Wagner [1], the oxygen concentration cells have been extensively used in laboratories as well as in industries. In metal-production technology, these cells have been used to monitor the oxygen potentials in metallic, slag as well as gas phases and also to control and styr metallurgical processes. The pioneer among the various industrial users of such cells is the copper industry. To-day, high temperature solid electrolyte cells involving oxygen ion conducting electrolytes have become an integral part of copper pyro-refining and continuous casting. In the present paper some of the applications according to the industrial processes are described including the developments that are going on in the European scene."

Jan 1, 1997

By Jewel Gomes

Produced water (PW) is salty water trapped in the reservoir rock and brought up along with oil or gas during production. It subsists under high pressures and temperatures, and usually contains hydrocarbons and metals. Therefore, it must be treated before being discharged to surface water. Different techniques are being used to treat PW through phase separations, system control and design, and chemical treatments. In this paper, we discuss our experimental results on treating PW through electrocoagulation (EC). The performance of EC was investigated for the reduction of chemical oxygen demand (COD) and metal ions. Effects of different electrodes, residence time, current density, and pH were also studied to optimize the treatment conditions. Different kinds of cleansing agents, such as lime and borax were used to break the buffering effect encountered during treatment. FTIR, SEM/EDS, and XRD were used to characterize the EC-floc and thus to elucidate removal mechanisms.

Jan 1, 2009

By D. M. Hausen

Applications of process mineralogy to the exploitation of molybdenum ores begins with early exploration and continues through the evaluation of mineralized prospects, to amenability testwork and pilot plant studies, to the development of a mineable orebody and to the development of a viable process for recovery. After plant construction, a broad range of products from a wide selection of sampling locations, i.e. grinding circuit, flotation cells, smelters and roasting kilns. etc., are evaluated analytically and microscopically, followed by periodic troubleshooting of problem points. The various crystalline phases of molybdenum that occur naturally and throughout various hydrometallurgical and pyrometal1urgica1 processes are identified and characterized by a variety of instrumental methods, including XRD-XRF, optical and electron microscopy, infrared spectrographic and differential thermal analysis.

Jan 1, 1989

By V. J. Ramirez, A. M. E. Noguez, M. J. Navarrete, B. G. Salas, N. T. Robert

"The close die forging stress in truncated conical cavities is evaluated with dimensional analysis. Five dimensionless groups are proposed from the process variables in order to simplify the forging stress determination. These groups are experimentally related and graphically expressed. This methodology can be used to predict the actual forging stress in industrial close die forgingThe use of the dimensionless groups allow to comprise more cases than the presented here, provided similar geometries and operational conditions.Introduction.Closed die forging is essentially a plastic deformation inside a two piece mold (forging die) with the inverted shape of the actual forging geometry. This plastic deformation will always be the result of a compressive stress. There are theoretical models which include complex calculations for the analytical determination of stresses (1, 2, 3, 4). Results of these calculations are approximate, requiring generally ulterior tests to obtain the true operational conditions(5).In this paper, it is presented a simplified approach to the actual compression stress needed in the forging. A well known tool in engineering: the Buckingham's Pi theorem in conjunction with dimensionless groups and a working piece scale model is used. Dimensional analysis will give the dimensionless terms needed to experiment with a selected scale model geometry to make the stress determination. The results presented demonstrate the reliability of this methodology."

Jan 1, 1997

By Animesh Jha, Chris Dometakis

"Without the use of a flux, only a poor dispersion of ceramic phase can be achieved. A molten-flux-assisted ceramic phase dispersion technique for producing aluminium alloy metalmatrix composites has been developed. In this paper, we report the physical chemistry for the dispersion of TiB2 in molten aluminium. In particular, aspects of the interfacial energy and the thermodynamics of the dispersion reactions are briefly discussed for enhancing the volume of dispersion phase in the molten metal and for controlling their morphology. This investigation also addresses the role of molten flux in the fabrication of AI-alloy mmc using a casting technique. The morphological aspects of the dispersion are explained on the basis of the classical theory· of nucleation.IntroductionMetal matrix composites (MMCs), have long been recognised as an important class of material due to their greater wear resistance, specific stiffness and temperature capability when compared to conventional monolithic alloys. Particulate reinforced composites produced by melt casting techniques have been amongst the first MMCs to achieve commercial market viability. The advent of melt mixing techniques such as the Duralcan™ process have enabled low cost, easily fabricated composites based on the AI-SiC and AIAlz0 3 systems to be produced. In this process, uncoated ceramic particles with diameters 10ltm and larger, are incorporated into conventional monolithic alloys with reinforcement levels up to 25 volume percent. The AI-7Si-SiC metal-matrix composites have good wear resistance, high strength, low density and high thermal conductivity. The combination of these physical and mechanical properties has become a major attraction for the fabrication of light-alloy composite disc rotor brakes for the automotive sector2. However, in silicon-free alloys, SiC is thermodynamically unstable above the composite melting point and is extensively attacked by the melt to form aluminium carbide3 :"

Jan 1, 1996

By Naixiang Feng, Shaohu Tao, Zhihui Wang, Yuezhong Di

"A novel vacuum aluminothermic reduction lithium process was developed in present work which used lithium carbonate, alumina and calcium oxide as raw material. The process mainly contained three steps. The first step is that LiA102 clinker is prepared in ambient environment, then metal lithium is vacuum extracted from LiAl02 clinker with aluminum power as reducing agent, and the last step is that alumina is leached from the reduction residue with a mixture of sodium hydroxide and sodium carbonate. The results show that the lithium reduction ratio can be over 95% under the conditions of reduction temperature 1423K, reduction time 3h, and aluminum excess 20%. The main components of reduction residue are CaO· Al203 and 12Ca0·7Alz03. The alumina leaching rate of calcium aluminate in residue is over 80%. High-whiteness aluminum hydroxide can be obtained by carbonation precipitation of the reduction slag leaching solution.IntroductionWith a density about half of water, lithium is with the lowest density of all solids, mere 0.5 g/cm3 at 20 °C [l]. Lithium is widely used in aerospace, aviation, nuclear-generated power and electric battery industry. Nowadays, over 90 % of the world's primary lithium is produced by molten salt electrolysis [2-4]. But the development of molten salt electrolysis will be effected by some factors: cost, environment, and so on. Vacuum thermal reduction may be used extensively in future because of its low-energy consumption, high-purity and short-cycle."

Jan 1, 2013

By Qingbo Yu, Qin Qin, Junxiang Liu

"Dry-granulation is a new process of molten blast furnace slag treatment and air is used as heat exchange medium. There are some shortages: poor effectiveness of granulation, high air-slag ratio and high energy consumption, which are the obstacles to popularize dry-granulation. Based on rotary cup atomization, the technique of recovering waste heat of molten blast furnace slag through waste heat boiler producing high pressure steam is exploited. The molten blast furnace slag is granulated to uniform small slag granules with high temperature, and slag granules pour into the waste heat boiler. It could produce steam, obtained in first row and second row tubes, when descending velocity of slag granules equaled 1.1mm/s and the Reynolds number equaled 7100. The application of the system for recovering waste heat from high temperature molten blast furnace slag has a significant meaning.IntroductionBlast furnace slag is one kind of solid waste in iron making process, which is discharged at the temperature range from 1723 to 1923K. In China, there was 0.162 billion tons of slag discharged in 2009, and the energy contained in the slag is equivalent to the energy in 9.4 million tons of coal equivalent. The sensible heat of molten slag is a very valuable waste heat source, so it is worthwhile to recover the sensible heat. At present, the molten slag is treated by a water quenching method. But in this process, the sensible heat is not recovered, moreover, an amount of water is consumed and harmful waste gas is discharged into the environment. Due to the considerations of energy conversation and environmental protection, the iron making industry pays close attention to dry-granulation, which is useful to obtain more benefits [1-4]. The sensible heat is recovered and an amount of water is saved by the method of dry-granulation. The amorphous content of slag granules obtained from dry-granulation is over 95% [5, 6], so the slag granules can be used as a perfect raw material for cement [7, 8].In the late 1970s, the Sumitomo Metal Industries, Ltd. and the Ishikawajima-Harima Heavy Industries, Ltd. jointly undertook the research of rotary drum granulation. This method has several disadvantages: the processing capacity and efficiency are low, and it is not adoptive to operate continuously in production [9]. From 1980, Nippon Steel, NKK, Kawasaki Steel, Kobe Steel, Sumitomo Metal Industries and Nisshin Steel were engaged on air granulation, and the experiments were operated for 6 years on the blast furnace in Nippon Steel. In the process of air granulation, there was great power consumption. The complexity of structure and the great floor space of the air granulation device caused high cost of investment. In 1986, Ukraine exploited a new method of heat recovery referring to the technology of Continuous Casting and Rolling [10]."

Jan 1, 2011

By Ralph H. Nafziger

The Bureau of Mines, in cooperation with the Idaho National Engineering Laboratory, has electroslag melted a V-5Ti-5Cr alloy using a fused CaF2, flux. The alloy is a candidate for use in future fusion reactors. One objective of this research was to evaluate the feasibility of the electroslag melting process in separating simulated radioactive isotopes from the V alloy to demonstrate recyclability. Small amounts of Ca, Y, and Mn were added as surrogates for radioactive isotopes. Results showed that this vanadium alloy can be electroslag melted satisfactorily. The impurities added intentionally were removed or decreased successfully. Among the major alloying constituents, Cr was retained but there were some Ti losses. The latter may be controlled with process refinements. This research suggests that the electroslag melting process could be a suitable method for recycling V alloys after use in future fusion reactors, or for processing other reactive metal alloys with more immediate applications.

Jan 1, 1996

By Satu Jyrkönen

A single-particle laminar-flow technique was used to study reactions of sulfidic nickel particles. The studied materials were three natural nickel concentrates and four synthesised nickel mattes. The variables of the experiments were the gas preheating temperature (500 - 1300°C), the composition of the reaction gas (N2 + 0 - 75 vol-% 02) and the ,particle size of the feed. Chemical analysis of the particles was used to determine the oxidation degree of the materials, and optical and scanning electron microscopy were used to detect alteration in their morphology, internal composition and structure. General reactivity of the materials was monitored by the extent of sulfur removal. The reaction mechanism of the studied materials was found to depend primarily on the materials composition as well as oxygen content of the reaction gas.

Jan 1, 1998

By H. L. Fraser

A review of the possibilities of performing microchemical analysis in thin sections using a combination of scanning transmission electron microscopy and energy dispersive spectroscopy of x-rays is given. Particular attention is paid to the factors that limit accurate analysis at the highest spatial resolution. As an example of the use of these techniques applied to a potential problem in minerals processing, the identification of iron pyrite and pyrrhotite particles in Illinois, Herrin #6 coal is presented.

Jan 1, 1981

By Terry C. Cheng

The Akita Hematite Process is currently the only hydrometallurgical iron removal process producing saleable iron by-products in the zinc industry. In this study, McGill University and Akita Zinc Co. have worked together into elucidating the basic precipitation chemistry of the process from the standpoints of hematite product quality and prevailing precipitation kinetics. This work determined that hematite is produced under the applied conditions (T = 195?200oC,PO2 = 103?414 kPa) directly without prior formation of basic ferric sulphate and transformation of the latter to hematite as thought originally. The rate-limiting step responsible for the long retention time (~180 min) was found to be either the re-dissolution of ferrous sulphate according to the batch reactor studies, or the slow hydrolysis of the remaining ferric sulphate according to the continuous reactor studies. Another interesting contrast between the batch and continuous reactor data was the degree of sulphur contamination (1.5 vs. 3.8%, respectively) and the specific surface area of the product (10 vs. 30 m2/g, respectively). These differences in addition to the co-precipitation of SO4-containing phases such as jarosites, alunite, and anhydrite were attributed to the significantly higher supersaturation level prevailing in the industrial continuous autoclaves that yields highly aggregated sub-micron hematite crystallites contaminated with chemisorbed sulphate ions.

Jan 1, 2003

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades. EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized.

Jan 1, 2003

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades_ EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized_

Jan 1, 2003

By Seksak Asavavisithchai, Natthida Jareankieathbovorn, Areeya Srichaiyaperk

"Recycling of ADC12 alloy scraps for fabrication of open-cell aluminium foams has been conducted via pressure infiltration method of replication process. The scrap, up to 50 wt.%, was melted with pure aluminium billet, followed by infiltration in a replicated mold of polyethylene foam structure. Compared with the pure aluminium foam, the compressive strength and hardness are higher for the foams with recycled scraps. The increase in foam mechanical properties is due to the presence of Si hard phase in Al matrix. The strength and hardness of the foams also increase with increasing contents of the scraps.IntroductionRecently, open-cell metallic foams have been brought to considerable attention of many industries due to their superior properties; such as large surface area, high specific strength, thermal conductivity, high service temperature and excellent anti-microbial activity, that cannot be found in conventional materials [1, 2]. Typically, open-cell foams are used in functional applications for which a requirement of high strength materials is not demanded. Good examples of such applications include heat exchangers, bone-replacement implants, interconnects, catalyst supports, and sound insulators.Among all types of open-cell metallic foams, aluminium (Al) is the most widely used base metal, due to low material cost, low density, low melting temperature and good corrosion resistance. To improve mechanical properties of Al foam, modification of foam microstructure with addition of alloy elements or ceramic particles is commonly carried out [3, 4]. ADC12 alloy is a typical die-casting Al alloy with high content of silicon (Si) close to the eutectic point in Al-Si binary phase diagram. The alloy is extensively used in the casting industry, due to high wear and corrosion resistance, low coefficient of thermal expansion and excellent castability [5]. The mechanical properties of Al-Si alloy are strongly dependent of Si content."

Jan 1, 2012