Search Documents

By Rao Pothini

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support. This paper describes in detail the testing methods, data analysis results obtained, and recommended changes.

Jan 1, 1992

By Christopher Mark

The demographics and safety record of the pillar retreat segment of the U.S. coal industry was analyzed using statistics collected by the Mine Safety and Health Administration. Pillar recovery is practiced primarily by mines in Appalachia and the Midwest. Using 1993 data, the accident rates and productivity of a large sample of pillar re- mines were found to be similar to other room-and-pillar mines in the same geographic areas. Pillar recovery apparently accounts for about 10% of all U.S. underground production, but has been associated with about 25% of the mf and rib fatalities during 1989-96. However, of the 28 fatalities that were analyzed, only 4 occurred for which no citations were issued for violations of mining law. Nearly one- half of the fatal incidents occurred during the mining of the last lift or pushout. All four no-citation incidents occurred during the removal of the last lift during a "Christmas tree" extraction sequence.

Jan 1, 1997

By Venkata S. Vutukuri

Compressive strength of cylindrical specimens of a model material and sandstone with various diameter/height (d/h) ratios was determined in unconfined compression tests. It was observed that the compressive strength increases with increase in d/h ratio. Triaxial compression tests were also conducted on the specimens of the same materials with a d/h ratio of about 0.47. It was observed that the axial stress at failure increases with increase in confining pressure. A very interesting correlation was found between the effect of d/h ratio on compressive strength in unconfined compression tests and the effect of confining pressure on axial stress at failure in triaxial tests. The relationships between d/h ratio and confining pressure, s3 in MPa are:- For model material - s3 = -0.95 + 1.7957*(d/h) 0.7883. For sandstone - s- (-0.4554 + 0.9888* (d/h) 1.0355. The correlation coefficients for these equations are 0.9997 and 1. These equations are valid for d/h ratios of up to 10.

Jan 1, 1993

By Gregory M. Molinda

Difficult mining conditions in deep western U.S. Iongwalls have necessitated the use of novel tailgate support systems. Extreme ground movement in these yielding gate systems has caused operators to utilize secondary support systems which match yield and strength characteristics with expected ground reaction. Other benefits include ventilation and safety gains, as well as lower costs. Recently, the use of novel support has been tried at longwall mines in other U.S. coal basins. One of the main considerations is the capability of the support to maintain an adequate airway for gob ventilation in gassy eastern coal mines. In one large Pennsylvania mine working the Pittsburgh seam, a number of support configurations were monitored over a 2,300 ft tailgate test area. The test included 4-pt wood cribs, Link-N-Lock cribs, Propsetter yieldable posts, cable trusses, and vertical cable bolts. Ground reaction, and thus support performance, was documented by roof sag and convergence instruments, ventilation measurements, and photographs. Various combinations of standing support and cable truss and vertical cable bolts provided adequate support for ventilation and safe escape. A cribless configuration consisting of only cable trusses and vertical cable bolts was inadequate to provide inby gob ventilation to the next open crosscut. Instrument ground movement data and visual documentation are presented.

Jan 1, 1997

By Winton Gale

"Rock and coal fractures and micro seismic vibration are common occurrences during development mining. It is very uncommon for coal and rock to be propelled into the roadway during normal mining operations. However, such occurrences do occur and appear to require significantly more energy than is available from strain energy release during coal cutting. The sources of energy, which can contribute to the propulsion of coal from the face or ribs, are typically strain energy from the surrounding ground, seismic energy from a rapid rupture of the ground in the vicinity, or rapid expansion of gas from within the burst source area.The aim of this paper is to briefly review the bursts that could be related to strain energy or seismic energy. However, the greatest emphasis is placed on the effect that gas within the coal could play in moderate to gassy mines.It has been found that the bursts related to the expansion of gas can occur in coal and stone. The volume of gas involved in coal bursts is typically lower than in gas outbursts; however, the process is generally similar.INTRODUCTIONA coal burst is defined as a rapid expulsion of coal (and potentially gas) from the boundary of the roadway. The volume of a burst can be variable, but volumes above 10-50m3 are noted and cause significant disruption to operations.Rock and coal fracturing is common about roadways, particularly under the influence of elevated stresses, either tectonic or related to mining abutment stress. Shear fracture is very common; however, it is very uncommon that the coal is propelled from the face or ribs as a result of fracture of the material. The nature of rock fracture about roadways under elevated stress is presented in Figure 1.A burst requires energy to propel the coal or rock from the rib or face of the roadway. The depth of material impacted may vary from 0.5m to greater than 3m inside the roadway boundary. The strength of the ground in this zone is variable depending on the nature of the coal seam (or surrounding material). Typically, this material has significant residual strength as confinement increases into the ribside.The energy required to propel this material is typically in addition to that which is associated with normal fracturing about the roadway."

Jan 1, 2018

By Daniel W. H. Su

Surface subsidence induced by multiple-panel coal extraction was calculated with finite element stress analysis. The use of nonlinear material behavior and GAP elements, which provide a realistic representation of shearing along existing planes of weakness, allows the finite element program to accurately reproduce observed subsidence profiles. A reduction factor of 1/6 is applied to the measured rock strength and modulus for use in the finite element model. The models satisfactorily predict a significant change in maximum subsidence and subsidence profile associated with an increase from subcritical to near critical panel width. Modeled shearing along planes of weakness is in good agreement with available time domain reflectometry field observations and is demon¬strated to have a very profound effect on the maximum subsidence and the shape of the subsidence profile. When both material nonlinearity and planes of weakness are incorporated, the finite element model appears to possess great potential for accurately predicting surface subsidence and subsurface strata deformation in environments where little subsidence information is available.

Jan 1, 1990

By Gift Makusha

Surface subsidence associated with coal mining activities in the Mpumalanga Province of South Africa changes the natural environment in several ways, and current challenges for mining companies include rehabilitation of the natural environment and the prevention of further degradation. To monitor the spatial and temporal evolution of surface subsidence, traditional fieldbased monitoring approaches such as GPS and spirit leveling are employed at a number of locations. However, the resulting measurements are point-based, and frequent revisitations are necessary to map the evolution of surface subsidence basins over time. To address these limitations, differential interferograms derived from repeat-pass satellite-borne synthetic aperture radar (SAR) systems were tested for their ability to measure and monitor surface deformation. The SAR data was captured by the European ERS-1 and ERS-2 satellite and covered a timeframe between 2008- 09-15 and 2008-09-15. The resulting interferograms revealed several features indicative of surface subsidence. Ground truth data confirmed the presence of a subsidence basin, detected using differential interferometry techniques during the 35-day period between April 12, 2008 and May 17, 2008; a maximum vertical deformation of 3.2 cm (1.3 in) was recorded. Interferometric monitoring revealed an eastward migration of the subsidence basin between June 2, 2008 and September 15, 2008 with an additional 4.7 cm (1.9 in) of subsidence observed. This migration coincides with the advance of the working face of the mine during this period. Finite element modeling will be performed in order to model the rates and evolution of surface subsidence haloes as underground mining advances. These presented results demonstrate the ability of interferometric synthetic aperture radar techniques to measure surface subsidence as well as the monitoring of the evolution of subsidence basins over time. This implies that the technique could be included, together with traditional field-based surveying techniques, in an operational monitoring system. With knowledge on deformation rates and subsidence basin evolution, informed decisions on current and future infrastructure development can be made and remedial actions and prevention strategies can be formulated for the problems associated with environmental degradation.

Jan 1, 2011

By David L. Kuck

This paper describes a system for providing structural, support in underground mines, employing water ice for pillars. packwalls and brattices. It consists of a refrigeration brine chiller, brine circulation system, and disposable plastic containers. The system provides for the timely freezing of uniform ice pillars, and for ice maintainance and/or melting on demand. Unique, useful ice properties include: expansion upon freezing, resilience to dynamic loads, and plasticity. Ice will not dilute or contaminate coal or ore. Economic advantages include: 1) lower labor and material costs (water can be piped to the ice pillar site through mine-water, spray-water, or drill-water lines); 2) replacement or supplementation of timber. concrete or other roof support equipment; and 3) potential use of ice brattices as ventillation control; and 4) conversion of ice bratices to ice pillars upon retreat. See Figure . A safety advantage for personnel and equipment is that ice pillars can be placed in hazardous sites, by remote control, if neccessary, without human entry. All filling, freezing and melting operations can be controlled from a safe distance.

Jan 1, 1987

By Collin L. Stewart

A summary of the results of a limited subsidence monitoring program at Cyprus Amax Coal Company's Shoshone Mine No. 1 in the Hanna Basin of south central Wyoming is presented. The monitoring program was designed to meet regulatory requirements for confirmation of subsidence predictions made in the mining permit. The longwall panels were 380 ft to 600-ft wide. Mining heights varied from 11 ft to 13.5 ft. Gate road development included three-entry and two-entry head and tail gates. Overburden depth varied from 150 to 945 ft. The coal seam and overburden dip at approximately 11 degrees. The overburden is very low to low strength mudstone and carbonaceous shale with low to moderate strength, silty sandstone interbeds. Panel W/h ratios varied from subcritical to supercritical. Smax was 0.9 of the mining height. The subsidence ratio was about 0.6 for subcritical width. The draw angle on the up-dip side averaged 20 deg. The draw angle on the down-dip side averaged 12 deg.

Jan 1, 1995

By M. V. Kurlenya

The experience of application of geomechanical investigations for substantiation of extraction of undermined ore deposit in the north of Siberia is discussed. The finite element method was used for forecasting the state of massif during the development of mining works. The results of calculations were compared with the experimental data of observations in situ for evaluation of authenticity of numerical modelling.

Jan 1, 1990

By Kent D. Mctyer

Mining commenced at Tasman Mine in late 2006. The current method of mining is bord and pillar using continuous minerbolters and shuttle cars for first workings and secondary extraction using mobile roof supports. The two stage process was chosen to accommodate irregularly shaped coal deposits, allowing adjustments to be made to extraction ratios for better management of subsidence and to maximize the efficiency of the operation. Following the completion of the first three full/partial extraction panels, the mining method was changed due to variable caving. Another partial extraction method, referred to as the Duncan Method was adopted; it involves stripping the developed square pillars on four-sides on retreat to leave a load-bearing remnant coal pillar. The system of partial extraction has been successful in meeting safety, productivity, and subsidence targets.

Jan 1, 2011

By Anthony T. Iannacchione

Underground bituminous coal mining is a large and significant industry within the Commonwealth of Pennsylvania, and it has a legacy of environmental consequence. For example, in 2008, 13.5 acres (5.5 hectares) of land were undermined by longwall mining every day. Laws and regulations have been promulgated requiring companies involved in this industry to remedy mining damage caused to homes, businesses, and land; replace impaired water supplies; and repair impacts to streams and wetlands. The regulations and technical standards set by the Pennsylvania Department of Environmental Protection (PA DEP) have been put in place to assure that coal operations comply with ACT 54 of the Bituminous Mine Subsidence & Land Conservation Act and other related legislation. These regulations and standards require operations to address impacts when a mining permit is submitted and as permits are modified and extended. One of the special provisions of ACT 54 is the requirement by the PA DEP to produce an assessment of the surface impacts of mining every five years. The University of Pittsburgh was contracted by the PA DEP to perform the 3rd assessment, which spanned from August 21, 2003, to August 20, 2008. This paper details the findings related to surface structure undermined during this period. A total of 3,735 structures were tracked. Four-hundred-fiftysix reported effects were found, and each required additional information and analysis. The majority of the reported effects were associated with eight longwall mines. Characteristics of the structures were analyzed and discussed, with special attention to those with reported effects. The number of undamaged and reportedly damaged structures (i.e., dwelling, barn, commercial building, etc.) undermined during the assessment period were listed. Lastly, the resolution status and type of resolution were analyzed for all structure reported effects.

Jan 1, 2011

By Steve Signer

The San Juan Mine and the National Institute for Occupational Safety and Health conducted a study to measure how development mining effected bolt loads. Twelve fully grouted, instrumented roof bolts were installed at two three-way intersections as part of the standard bolting pattern. Newly developed miniature data acquisition systems (MIDAS) were used to measure bolt load changes during initial face advance and cross-cut breakthrough. The effects of cut placement and depth on roof bolt loads were studied This test showed how bolt loads increased at five positions along the bolt length during initial mining. Both entry advance and cross-cut breakthrough produced a similar percentage of increase in bolt loads. Geologic differences between the test sites were probably responsible for the differences in amounts of bolt loading. The test site with more top coal and a higher rock quality designation (RQD) had lower bolt loads.

Jan 1, 2004

By Christopher Mark

Despite more than half a century of experience with roof bolting, no design method has received wide acceptance. To begin to improve this situation, National Institute for Occupational Safety and Health (NIOSH) conducted a statistical study of roof bolt performance at a number of mines throughout the U.S. Case histories were collected from 37 mines with a variety of roof bolt types and patterns in a wide range of geologic environments. Performance was measured in terms of the number of roof falls that occurred per 10,000 ft of drivage. The study found that roof falls are rare when the roof is strong and the stress is low, even with light roof bolting patterns. The focus of this paper is on the more difficult conditions, where the roof is weaker and/or the stress is higher. Analysis of the results led to guidelines that can be used to make preliminary estimates of the required bolt length, capacity, and pattern. The guidelines are based on the depth of cover (which correlates with stress) and the roof quality (measured by the Coal Mine Roof Rating (CMRR), and the intersection span. Another contribution is a formula for estimating the horizontal stress level in the eastern U.S. coalfields as a function of the depth of cover. The design guidelines are currently being implemented into a computer program called Analysis of Roof Bolt Systems (ARBS).

Jan 1, 2001

By Keith A. Heasley

Pillar recovery in deep coal mines with competent roof and floor can concentrate stresses and generate hazardous bumps. Actual calculation of the geologic strain energy released in association with these coal bumps has been rare, although energy release values have been utilized successfully for indicating burst potential in numerous hard- rock mines. This paper advances the current knowledge of energy release calculations as applied to coal bumps through an extensive analysis of an actual bump occurrence. The U.S.B.M, displacement- discontinuity code, MULSIM/NL, is used to produce a numerical model which generates stress, displacements and energy values associated with a pillar retreat section. This model is calibrated with actual field data, and then dissipated energy values from the model are examined as to their suit- ability for indicating bump potential. Ultimately, it is determined that prudent application of dissipated energy calculations can be used as a tool to investigate the coal bump potential of a mining plan or cut sequence.

Jan 1, 1990

By John P. Dunford

Ground support continues to be the most important safety consideration in underground mining. The Bureau of Mines has developed a yielding steel post with a capacity of 45 tons and b c1osure allowance of 24 inches in a 6 to 7 foot seam height. The post mechanism in a three piece unit consisting of a top and bottom leg made from standard steel pipe and a separate foot bracket. It develops its load carrying ability when the lower pipe, with an attached interference ring, is forced into the larger top leg. The walls of the top leg are deformed radially and along the axis. Yield continues until the unit bottoms out. Other advantages of the post is that due to its simplicity it can be made at the mine shop level and its cost should be about one-hundred dollars. Prototype units were tested in the laboratory. Based on these results, modifications were made that would make the post perform better as a mine support. Two field tests were conducted. The first test used the units as supplemental support for the wood crib rows in a longwall tailgate. The second and larger field teat had 84 posts placed on salvaged track rails. They were installed on two foot centers in the middle of the entry. Overall the supports functioned well during use in the headgate entry, but problems with the quality of some of the pipe caused localized failures. However, these problems can be attributed to one manufacturer of pipe and through tighter specifications can be eliminated. The use of the posts with the rails is showing additional benefits as a ground support system. By providing continuous support between the posts a beam is created that has much more load bearing. The additional support can reduce floor heave and in some cases eliminate the need for the rib side crib line.

Jan 1, 1986

By James M. Tennant

In the mid 1970's, American Electric Power significantly expanded its internal coal production. This involved opening several large mines in seams that had never been mined on a large commercial scale before. One of the mines opened was the Martinka No. 1 Mine which is located approximately five miles southeast of Fairmont. The mine was originally designed for room and pillar mining with continuous miners but was later modified to permit the utilization of longwalls and continuous miners for entry development. The coal seam to be mined was the Lower Kittanning which averages fifty-six inches. In order to successfully mine this seam, it required that the mine design recognize the effect caused by the dip of the seam which averages four percent to the Northwest with a maximum of sixteen percent for short distances and a relatively low cover. In fact, seventy-four percent of the reserves have cover of less than four hundred feet. Also, the core hole data indicated that the immediate roof varied from zero to eighteen feet of shale with two to forty-five feet of sandstone overlying the shale.

Jan 1, 1982

By S. Y. Liu

Based on the underground measurements, physical model test of simulated materials in the laboratory and finite element analysis, this paper demonstrates the pattern and process of roof fall over the tip-to-face area in the fully mechanized coalfaces. The main factors that affect the stability of the immediate roof are thoroughly studied including the fracture position and tilt angle of the main roof, the tensile strength (Rt) and cohesive force (c) of the immediate roof, and type and resistance of the powered support. Based on these factors, this paper proposes the basic process of immediate roof breakage a. follows: As the longwall farm advances, the main roof breaks and then rotates. A tensile fracture zone will be formed in the immediate roof under the fracture line of the main roof. A caving zone (plastic zone) will be formed in unsupported area between coalface and canopy tip. If these two zones overlap the immediate roof will be completely unstable. Under this condition, powered support will have difficulties lo control the rod. Therefore it is necessary to study the process of immediate roof breakage and look for effective methods for controlling the roof.

Jan 1, 1990

By Kot Unrug

Fully grouted tensioned bolts provide a desirable compressive of laminated roof and bondage along the entire bolt length, at the same time the entire surface of the hole is protected against penetration of moisture. This is particularly important in shale strata, where, when left unprotected by a partial grout column, moisture penetrates to the annular space, and weathers rock around the bolt hole, having an easy access to the bedding planes which are strongly hydrophilic. The most desirable are thrust tensioned rebar bolts that can be installed with one procedure step, and can secure a desired pre-stressing. Such bolts have a forged conventional head and offer no hazard to miners in low clearance mines, whose number increase constantly due to the depletion of reserves in thicker seams. The presented field-testing program has been based on instrumented bolts allowing for monitoring of tension at installation and at a chosen time interval after. The tested system is based on rebar bolts installed with two speed Fosroc resin (fast at the top and stow at the bottom), and mechanical compression by the bolting machine at installation. Combination of several different washer -- plate arrangements have been tested. The results are reported with their interpretation, and recommendations directly towards strata control requirements, as well as the operational considerations for efficiency of installation.

Jan 1, 2002

This paper presents a two-dimensional numerical procedure which incorporates concepts related to the mechanics of strata deformation' as well as' empirical indices associated with subsidence engineering. Regional deformation data were employed in order to establish overburden deformation zones, while material properties were kept constant. Scaling of final displacements was based on empirically predicted values for subsidence and strain for the Appalachian coalfield. The model was validated with a number of regional case studies and predicted subsidence and strain curves were compared to those obtained using the semi-empirical influence function formulation developed by VPI&SU.

Jan 1, 1988