Search Documents

By J. H. Gasper

The overall success of steep slope (>20°) contour mining is dependent upon many factors. The major factor is the selection of the mining method that best suits the premining site conditions both environmentally and economically. These conditions can be divided into three major categories: 1) Geometric Conditions --machine limitations, slope stability restrictions, erosion capacity, among others; 2) Physical Conditions--material properties, rock strengths, diggability, driving surfaces, among others; 3) Chemical Conditions --acid/base relationships, blending or selective placement of overburden, among others. This paper incorporates these conditions through conceptually modeling compliance oriented contour mining methods; in particular Haulback methods, utilizing: 1) the Front-End Loader (FEL)/Truck; 2) Tractor Scrapers; and 3) Combined FEL-Truck/Scraper. Engineering analyses including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces), drainage requirements and many others can be performed after the geometric constraints dictated by in-situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views, but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By R. B. Steele

The paper contains the results of the physical and mathematical simulations (based on the finite elements simulation) of the length and shape influence on the mechanical strength of the brex. Key words: Stiff extrusion, extruded briquettes, BREX, mechanical strength, cold strength, compressive strength, tensile splitting strength, oval shape, finite elements simulation. INTRODUCTION Extruded briquettes (BREX) exhibit a set of unique properties when compared with briquettes formed by alternative methods. Brex generally have sufficient integrity right after extrusion to withstand the necessary handling and stockpiling and does not require any special means and tools for the green briquettes strength conservation. In a typical die without an ancillary cutting device green brex tend to have very high length to diameter (L/D) or length to section area ratios. For round hole dies the brex are typically 5to 6 times the diameters and even longer. Stiff-extrusion allows also for the very easy changing of the forming dies. Dies with different cross-sectional shapes of the brex (round, ovals, square, hollow structures and many other two dimensional shapes) are possible, and common. The results of our investigations show how these geometrical shape factors contribute to overall quality of the brex both in terms of strength and as new charge components in metallurgical furnaces and processes [2-4]

Feb 27, 2013

By Richard H. Lindgren

I appreciate this opportunity to discuss with you OPIC's new policies designed to assist U.S. minerals companies in developing new sources of minerals overseas. A comparison of recent figures on U.S. investment in mineral exploration, development and production gives results which are remarkable --and disturbing. Through the 1960's the flow of U.S. foreign direct investment in mining and smelting in the developed and less developed countries were nearly equal. However, by 1973, roughly 80% of all exploration expenditures by mining companies was taking place in the developed countries and principally in the U.S., Canada and Australia. Clearly it is to the interests of both the developing countries and the United States to put these figures back in better balance. As you may be aware, the administration as a whole is examining systematically what can be done by government to reduce the disincentives and increase the incentives to mineral investment in the less developed countries --the LDCs. A subgroup of the National Advisory Council chaired by the Treasury Department has been formed to coordinate U. S. Government policy and program efforts relating to mineral and energy development in these countries. Among other matters, this subgroup will examine how public policies could positively influence the private investment decision-making process in the minerals industry.

Jan 1, 1978

By Kapila Pathirage, Michael S. Schultz, Gregory Sanders, Ulf G. Gwildis

Adequate understanding of the subsurface conditions along the alignment of a planned tunnel is key for managing project risk. For achieving this understanding, geotechnical borings are conducted during design. Where their spacing cannot reduce the risk of encountering differing site conditions (DSC) in-between borings to an acceptable level, supplemental exploration methodologies or data evaluation approaches may be required to bridge the data gap. This paper compares the exploration design approaches of recent tunnel boring machine (TBM) and microtunnel boring machine (MTBM) projects in the quaternary deposits along the Eastern Seaboard, the glacial geology of the Pacific Northwest, the sedimentary rocks of the South, and metamorphic rocks in western Germany, describing their respective effectiveness of managing DSC risk.

Dec 1, 2022

By A. T. Iannacchione

Recent fatal injuries occurring during pillar retreat coal mining call for better identification of the hazards and recognition of risks. Ground control hazards associated with room-and-pillar retreat mining tend to intensify with depth, requiring extra precautions in the form of additional controls. In many locations these activities are further complicated by local complexities often associated with unique or novel circumstances, such as over-mining or under-mining. One technique recently studied by NIOSH, Major Hazard Risk Assessment (MHRA), may help mine operators to mitigate the risks associated with pillar recovery operations. The approach was trialed at two underground coal mines in southern West Virginia that are currently practicing pillar recovery. The first step in the MHRA process involved reviewing the segments or parts of the pillar extraction mining system and identifying associated hazards and threats to the operation. Some of the high risk hazards at these two sites included: ? Rock fall during pillar extraction covers equipment and injury occurs during recovery operations, ? Rock fall above the roof bolt horizon, potentially injuring ? workers and/or requiring recovery action, ? Rib fall under deep cover, potentially injuring workers, and; ? Strata instabilities associated with subsidence of the interburden due to simultaneously mining two seams in close vertical proximity to one another. The mines? risk assessment teams then considered each threat individually in order to systematically identify potential unwanted events. The top unwanted events were examined individually using structured risk analysis tools. The output from the process includes a list of priority existing controls for monitoring and auditing, and a second list of potential new controls. These controls consisted of: Examples of best practices, ? Enhanced communication, ? Implementing standard operating procedures (SOP), ? Protocols for emergency response actions, ? Effective layouts, ? Efficient monitoring, and; ? Successful audits. This paper documents the process as it unfolded at the two mines, and analyzes the strengths and weaknesses of the MHRA technique as it applies to pillar recovery operations. This work was part of a larger NIOSH research project. NIOSH was responsible for: 1) facilitating the risk assessment process known as Major Hazard Risk Assessment (MHRA), 2) documenting the risk assessment process, and 3) providing mine management with a written draft summary of the risk assessment process. The results of the risk assessment represent the thoughts and opinions of the individual risk assessment teams and should in no way be construed as an endorsement of the risk assessment output by NIOSH or the University of Pittsburgh.

Jan 1, 2009

By I. Michalakis

A geological and geophysical study was con-ducted at the area of Stylos, Hania in order to study the possible mechanisms of saltwater contamination. A new detailed geologic map in scale 1:5,000 was combined with the results of a time lapse geophysical survey using seismic and electrical methods. A fault system in the N-NE direction possibly favors the saltwater intrusion.

Jan 1, 2006

By Ratnakar Singh, Raj Kishore, Kisor Kumar Sahu, Ranjeet Kumar Singh, Ganesh Chalavadi

The Falcon concentrator is capable of separating minerals in fine size classes based on their differential density. Separation of mineral particles depends upon the fluid flow characteristics and relative movement of particles in a fluid. In the present study, a fluid flow characteristic inside the Falcon concentrator was established through experimentation and modeling. The Falcon concentrator has two fluid entry points: (a) Fluid entering through gravity assisted feeding system and (b) Fluid entering through the fluidized hole on the concentrator wall. In order to identify the role of fluid entering the concentrator, a tracer was injected into the system. As per the tracer based experimentation, it was established that fluid entering through the gravity based feeding system is responsible for thin flowing film formation in the stratification zone where particles are stratified based on their relative density. The momentum balance and continuity equations were simplified for a high centrifugal force field, and the fluid velocity profile was estimated inside the thin flowing film. Estimated fluid flow profiles will help to simulate the particle trajectories inside the Falcon concentrator. The influence of rotational speed, fluid flow rate, and cone angle on the fluid velocity profile were investigated. Fluid thickness over the concentrator wall is also estimated, and it is typically of the order of ~150–200 μm.

By L. C. Atkinson

A three-dimensional finite element Ground-water flow code has been developed that incorporates saturated/unsaturated, two-regime flow (i.e., both Darcian and non-Darcian) and solves for the seepage face at a surface of outflow. This code is capable of more realistically predicting ground-water inflows to an open-pit mine under the throttling effects of non-Darcian flow. The height of the seepage face on highwalls and the shape of the phreatic surface in the vicinity of the pit that it calculates can also produce more probable estimates of pore pressures for analysis of slope stability.

Jan 1, 1992

By W. A. Zingg

Impervious zones in copper waste heaps create a problem in contacting the rock with leaching solutions. These zones are normally associated with compacted layers .formed on the surface of each lift by dump truck traffic and by disintegration of the rock exposed to atmospheric conditions. These layers are usually only a few feet in depth--but, nevertheless, act as barriers to vertical flow causing the leach solution to perch in the heap, Consequently, much of the rock remains untouched and the leach solution breaks out the side of the heap instead of continuing downward to bedrock. One solution to this problem is breaking the hard pans with explosive charges. However, to use explosives means adopting new explosive materials and methods. To use this process successfully requires finding answers to operating conditions inherent to waste heaps. Foremost among these are: (1) type and size of casing that can be used because of limitations brought about by drilling problems, caving and, corrosive conditions; (2) perforating the casing at required levels; (3) an explosive capable of being pumped; (4) obtaining detonation of the, main charges through, the wail of the casing; (5) an explosive with the ability to propagate through the voids of the rubble and one which is not affected by water, acidic solutions, or back pressure conditions from hydrostatic heads; (6) to heave and rupture the compacted zones without chambering or recompressing the waste material.

Jan 1, 1970

By R. J. Hamilton

Considerable success has been achieved in recent years in reducing concentrations of respirable dust in UK coalmines; thankfully this has been reflected in significant improvements in pneumoconiosis statistics. However, continuous increases in mechanisation and in rates of working, accompanied by more stringent dust regulations, necessitate the introduction of improved and often more sophisticated methods of dust control. The increased application of exhaust ventilation and air cleaning techniques seems likely to be the most important step forward in dust control in coalmining during the next few years. A typical drivage in a UK mine is not more than 16 ft (5 m) wide and is supported by steel arches. In the past the majority of such roadways were driven by the conventional means of blasting and loading. Since the main purpose of ventilation was to clear blasting fumes and to provide adequate scouring of firedamp, not surprisingly it was usual to have 'forcing' ventilation. Present systems of operation are making increasing use of heading machines and it is not surprising that well over half of all drivages are now ventilated by exhausting methods. (1) The great majority of coal getting in the UK is from longwall faces, usually in seams of less than 6 ft (1.8 m) thickness. Although this method of min¬ing has many advantages in terms of safety and productivity, dust control is made more difficult because of the need for men and machines to work in the same ventilation stream. Much emphasis has been placed on improving the design and methods of opera¬tion of longwall machines to reduce dust production, and improved ventilation has provided greater dilution, and in consequence, reductions in dust concentration. On all machines water is now fed through internal galleries to the cutting elements. Unfortunately, one of the difficulties associated with mining thin seams is that there is some unavoidable cutting in the roof or floor and in many seams there are faults to be traversed and dirt bands which must be removed with the coal. Under these conditions it appears that the use of exhaust ventilation and air cleaning offers the most promising way of achieving satisfactory dust conditions.

Jan 1, 1980

By Roland C. Walker

Traditional headed rebar has existed in the mining industry as a ground support product for many years. The head of a rebar bolt is most commonly produced by hot upset die forging. Upset die forging produces a rugged, simple head that performs well. Certain elements of the head must comply with regulatory standards, such as ASTM F432-95, which offers a standard test procedure to ensure quality of the product. The head style produced by all major manufacturers has been optimized to reduce manufacturing costs, provide greater miner safety and provide an excellent performing product. Observations were made in some mines of heads failing under in-situ loading. These observations could not be replicated according to the ASTM testing method. This paper highlights the problem and how a solution was developed. The development includes pictures of in-situ failures from the underground operations, laboratory replication tests indicating how this loading occurs, and then the use of this calibrated test method to validate the new design created.

Jan 1, 2009

By S. M. Khandrika

It is shown that dewatering of fine coal particles (D50 : 21 microns) is enhanced near the point of zero charge. The coal surface is modified by the addition of copper ions and adjusting pH to precipitate surface active metal hydroxy species which promote agglomeration and produce low moisture cakes. Filtration kinetics data are used in calculating filter cake parameters from an integrated form of Darcy's law. The influence of copper ions and pH on filter cake parameters and correlations among them are presented.

Jan 1, 1993

By C. M. Liu

"The Freeport-McMoRan Sierrita Crystal Plant produces Copper (II) Sulfate Pentahydrate (CuSO4·5H2O) through a series of cooling crystallizers. In this process, high supersaturation and unwanted spontaneous nucleation promote fine crystals. Seeding through recycled crystal classification can manipulate the crystal size distribution (CSD) for larger crystals. Proper selection of the crystallizer for seeding can prevent spontaneous nucleation and promote final crystal size. This study shows when seeding temperature is closer to the crystallizer temperature, suspension densities in the crystallizers are promoted and overall CSD shifts to a larger size of crystals. INTRODUCTION Figure 1 shows an overview of the crystallization process. The in-plant feed flow, called Pregnant Mother Liquor (PML), enters the first crystallizer and is subsequently cooled through a series of four crystallizers. Specific temperatures are targeted for each crystallizer to ensure the crystallization process is operating within the metastable zone (MSZ). The discharged flow from crystallizer #5 then enters two cyclones. The overflow from the cyclones contains smaller crystals providing seed crystals for crystallizer #5. The underflow from the cyclones begins the drying process. The overflow from crystallizer #5 enters cyclone #3 for removal of fine crystals and seeding purposes. The underflow from cyclone #3 has the capability to provide seed crystals for crystallizer #1 or crystallizer #2. The overflow leaves the system as Spent Mother Liquor (SML). Undersize crystals dissolve into the PML and return back to crystallizer #1.THEORIES AND METALLURGICAL TESTS Seeding requires an understanding of the crystal size, solution temperature and amount of crystals that enter the crystallizers (1). For the seed crystal size, classified crystal seeds can prevent fine crystals returning back into the system which eventually leads to excessive agglomeration (2). Proper selection of the crystallizer can ensure seeding at an appropriate temperature. Seeding at a temperature much lower or higher than the saturation temperature promotes spontaneous nucleation. Typically, seeding between 4-5°F below the saturation temperature is acceptable (5). A general rule of thumb is to add the seed crystals at the temperature between the solubility curve and the metastable zone. An experiment conducted by Mettler-Toledo AutoChem, Inc. indicates seeding close to the solubility curve rather than the metastable zone promotes a lower supersaturation and nucleation rate but yields a higher growth rate and a greater number of larger crystals (1). The amount of seed crystals can not only change the suspension density but also narrows the width of the MSZ in the crystallizers. An experiment conducted by Jaroslav Nyvlt reports with the crystals absent, the maximum allowable undercooling is 6.3 degrees at a cooling rate, 5°C/hour. With the presence of crystals, it narrows the MSZ width to 2.2 degrees (4). Industrial crystallizers normally operate at suspension densities between 15% and 25% by mass. When suspension densities are lower than 15%, it increases the risk of primary nucleation and the probability of incrustations; on the other hand, if the suspension densities are greater than 25%, it can cause a greater attrition rate and increase the probability of deposits (6). Moreover, operating suspension densities between 15% and 25% are also sufficient to minimize supersaturation rate which promotes crystal growth over nucleation (2, 6)."

Jan 1, 2015

By W. Holding

Since the 1975 International Mine Ventilation Congress in Johannesburg there has been a trend in South Africa towards making the mine ventilation departments responsible for monitoring the total environment. This includes the taking of noise and illumination measurements and there is in fact a debate taking place as to whether the departmental title should be changed to 'Environmental Control Department'. The organisers of the 2nd international Mine Ventilation Congress have decided that noise and illumination will not be included as Congress subjects and 'Total Environment' includes only those facets which are open to debate at the Congress. The choice of mine is significant in that while most Congress papers from South Africa will be devoted either to coal mining or to the somewhat unique deep level gold mines, Prieska Copper Mine is a mine which can easily be identified with similar mines in many other parts of the world. The mine is situated some 750 km south west of Johannesburg and about 600 km north east of Cape Town. Current production (ore and waste) is about 340 000 tons per month and the total underground labour force is just over 2 000. The ore body is a massive sulphide, the main minerals being copper and zinc and the method of mining is sub-level open stoping. Daily average surface temperature conditions range from 85°F (29.5°C) dry bulb and 69.8°F (21°C) wet bulb in mid-summer to 42°F (5.5°C) dry bulb and 36.5°F (2.5°C) wet bulb in mid winter. The information presented in-this paper is limited to what can be gathered by mine ventilation staff as part of an on-going exercise and is obviously not as comprehensive as would be the case if a fully equipped research establishment were to become involved. The paper will be divided into three sections 1) Gases 2) Dust 3) Heat In each section statutory and/or other standards will be set down followed by a discussion of assessment and in some cases control methods.

Jan 1, 1980

By J. R. Patts, L. D. Patts, S. J. Janisko, T. Barone

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more efficient and effective use of rock dust. A prototype, flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed in line between the ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over a period of three days at set distances from the fan exhaust to assess the changes in float coal dust levels in the return due to the operation of the scrubber. Mass-based measurements were collected on a per-cut basis and were normalized per foot of advance by the continuous miner. Results show that average float coal dust levels measured under baseline conditions were reduced by over 91% when operating the scrubber. INTRODUCTION In 2012, underground mining in the United States produced over 342 million tons of coal [EIA 2013]. During the cutting, crushing, and transport of this coal, dust is generated and can be entrained in the air ventilating the mine. Title 30 Code of Federal Regulations Part 75.400-1 (30 CFR§ 75.400-1) defines float coal dust as particles of coal that can pass a No. 200 sieve. These coal particles can be carried by the ventilating air into return entries before settling onto mine surfaces [NIOSH 2006]. If this float coal dust becomes re-entrained into the airstream, it can propagate an explosion throughout mine workings [Harris et al. 2010]. Application of rock dust in underground coal mines is required by Federal regulation as a means of preventing the propagation of explosions by float coal dust. In order to meet Title 30 Code of Federal Regulations Part 75.403 (30 CFR § 75.403), 80% incombustible content must be maintained in the composition of dust deposited in mine entries [76 Fed. Reg. 35968 (2011)]. This fraction of incombustible content is increased if elevated levels of methane are present. In order to maintain the required incombustible content, frequent or constant application of rock dust is undertaken by mine operators. Title 30 Code of Federal Regulations Part 75.2 (30 CFR § 75.2) defines the properties of the rock dust that must be used by mine operators."

Jan 1, 2015

By Marini David, Pigorini Andrea, Fuoco Stefano, Zurlo Raffaele

"The excavation of a tunnel in highly weathered and strongly fractured rock masses due to tectonic actions is still a challenge. In order to maintain reasonable productivity, excavation through a wide zone of highly tectonized rock mass requires a detailed, integrated study of the construction solutions and a monitoring system to minimize the process time and to optimize the adopted consolidation measures in accordance with a predefined matrix of possible support systems. This paper summarizes some interesting data acquired during the excavation of the Brenner Railway Base Tunnel system between Italy and Austria. The Brenner Base Tunnel (BBT) runs through the fault line between the European and the African tectonic plate. This big fault zone is called “Periadriatic Line.” In particular, data acquired in the exploratory-service tunnel have been analyzed. Furthermore, the base concepts for defining the consolidation and support solutions adopted for the excavation of the exploratory tunnel are described. INTRODUCTION The Brenner Railway Base Tunnel (BBT) is a system of underground structures and tunnels that is designed to connect Italy and Austria using new railway standards. It is based on high speed (HS) concepts and applies the European Standards for Interoperability (TSI). The railway includes twin tunnels for a total length of about 55.0 Km without considering the connection tunnels to the existing underground railway in Innsbruck. Including the latter, the total length of the tunnel system reaches 64 Km, and is among the longest tunnels in the world. The Italian section passes through the so-called ""Periadriatic Line,"" which is an important tectonic structure generated by the collision between the European and the African tectonic plates. Despite the extensive investigations carried out (boreholes down to 700 meter depth), significant geological and mechanical uncertainties inside the Periadriatic formations remained unsolved. In order to elevate the level of confidence and observe the behavior of the rock mass at a representative scale, the BBT Authority decided to excavate in advance the service tunnel, which has taken the function of an exploratory tunnel. The data and observations collected during its excavation would provide important insights for the design of the main tunnels."

Jan 1, 2016

By Bruce Hebblewhite

"Historically there have been a number of different hypotheses and empirical models developed in an attempt to describe the nature of fracturing above longwall panels in underground coal mining. The motivation for such models varies, ranging from understanding the impact of mining on surface subsidence to back-analysis of caving behaviour in the immediate roof behind the longwall face. One of the most critical motivating factors that is taking on increased importance in many coalfields is the need for better understanding, and hence prediction of the impact of mining on overlying strata, particularly strata units acting as aquifers for different groundwater horizons.This paper reviews some of the major prediction models in the context of observed behaviour of strata displacement and fracturing above longwall panels in the Southern Coalfields of New South Wales, south of Sydney. The paper discusses the parameter often referred to as “height of fracturing” in terms of the critical parameters that influence it, and the relevance and appropriateness of this terminology in the context of overlying sub-surface subsidence and groundwater impact. The paper proposes an alternative terminology for this parameter that better reflects what it is and how it is used. The paper also addresses the potential role of major bedding shear planes mobilised by mining and their potential influence on overlying subsidence and groundwater interference.INTRODUCTIONKnowledge of the detailed nature of rock deformation and failure above any form of large-scale underground mining is always going to be limited to interpretation from a very incomplete set of data. It is extremely difficult, if not impossible, to directly measure the detailed nature of the rock failure, fracture networks, and deformational behaviour above an extracted mining area. Limited techniques such as borehole extensometry can provide some evidence of relative or incremental deformation in the direction of the borehole (usually vertical). However, such data cannot assist below the horizon where full caving has caused major rotation and dislocation of rock blocks and effectively destroyed the instrumentation borehole. Above such a horizon, the data is only valid along the axis and in the direction of the borehole, and to the level of detail defined by the extensometer anchor spacing intervals. It is often also restricted by major shear planes intersecting the extensometer borehole and cutting off the instrumentation below the level of the shear horizons."

Jan 1, 2019

By John R. Riede

The use of radioactive gages in beneficiation plants is relatively new However, enough applications have been made so that it is now possible to positively state that these gages have definitely progressed from a laboratory device to a very rugged and reliable on stream process measuring instrument. Gamma Ray Gages of the type presently being used in the beneficiation industry consist of three basic components: (1) A source of radiation (2) A radiation detector (3) An electronic amplifier The source is usually a radioisotope such as cesium-137, or cobalt-60. This source, adequately protected and ruggedly mounted, is most commonly placed on one side of a pipe or vessel. The radiation detector is then mounted on the opposite side, Since the absorption of gamma radiation as it passes through various materials is a function of the density of the material, the change in radiation measured by the detector is proportional to the change in specific gravity of the product in the pipe or vessel. One popular type of detector in use today is a cell which converts radioactive energy directly into electrical energy1. This electrical energy, when amplified, presents a usable output for metering and control devices. There are, of course, many other components which are part of a working gamma gage installation, such as zero compensators, lead shielding, mounting brackets, equivalent absorbers, etc.

Jan 1, 1958

By Stephen R. Holsinger

During the year of 1972 ASARCO's Silver Bell embarked upon a project that would test a modified grinding circuit using direct digital compute against the performance of its other five grinding lines, implementation and subsequent outcome of that project has been previously reported in a paper by Pitts, et al. The main purpose of the present paper will be to describe major problems incurred during the implementation of this control strategy on the remaining five primary grinding lines and their solutions. Also included will be a discussion of changes made in operating philosophy and methods used since that report was written. Description The Silver Bell concentrator is a 10,436 tonne/day copper sulfide plant supplied by ore from two separate open pits approximately 4 km. apart. As well as receiving ore from these two main pits, ore is received from several exten¬sions of both pits. The ore bodies are variable in rock type and the extensions have increased this variability. Grinding is carried out by six primary, single-stage, 3.20M x 3.66M Allis Chalmers grate discharge ball mills in closed circuit with four Krebs D20B cyclones (Fig. 1). Each of these grinding circuits is controlled by four independent but interactive control elements. These control elements are the fresh ore feed, the water added to the feed end of the mill, the water added to the ball mill discharge sump, and the cyclone feed pump speed. At the present time, instrumentation for measuring primary process variables consists of Merrick weightometers for fresh ore feed, orifice plates coupled with differential pressure transmitters (dp's) for incoming water measurements, back-pressure diaphragm coupled with a dp for estimating ball mill discharge sump level, a magnetic flowmeter for determining cyclone feed velocity and a nuclear density gauge for measuring cyclone feed density. All measuring instruments develop electrical signals that are measured as 2-10 V DC "inputs o the computer interface.

Jan 1, 1977

By C. D. Wittreich

The University of Idaho, Department of Metallurgical and Mining Engineering, through the Generic Mineral Technology Center, has been engaged in mine design research at the Lucky Friday Mine, Mullan, Idaho. The purpose of the research is to develop and implement the longwall underhand cut-and-fill mining method for conditions at the Mine. The longwall underhand cut-and-fill mining method involves backfilling mined stopes with a compacted tailings-cement mix. After the backfill has been allowed to cure, mining is resumed from underneath. Horizontal stresses in the Lucky Friday Mine are exceptionally high and rock bursts are a common problem. Beus and Chan (1980) have reported a 2:1 horizontal to vertical stress ratio at the mine with a 65-MPa (9,500-psi) maximum horizontal stress at the 1,295-m (4,250-ft) level. Using this mining method under these stress conditions, it is desirable to have a backfill material that has sufficient strength to safely carry the high horizontal wall loads while minimizing external steel supports.

Jan 1, 1987