Search Documents

By Y. Luo

Surface subsidence monitoring is the most effective means for investigating the nature of, and developing the techniques for predicting, the surface movement and deformation process. However, because of imperfection in survey equipment and field practices, the surface movement data collected from field survey are not error-free. Also due to lack of proper numerical techniques for computing surface deformation from the measured surface movement data, a relatively large portion of the subsidence data collected could not provide more information other than surface movement. In this paper, the sources and magnitude of errors in the measured surface movements and calculated surface deformation are discussed. Techniques for improving the accuracy of the calculated deformation indices (i.e., slope, strain, and curvature) are developed. The proposed techniques include: (1) proper selection of monument spacing for subsidence monitoring; (2) a data smoothing technique for data pre-processing; and (3) a number of numerical methods and/or procedures for calculating surface deformation indices from the measured surface movement data.

Jan 1, 1992

By Laurence E. Snow

The conversion to the use of commercial grade ammonium nitrate (CGAN) for use in blasting at the Utah Copper Pit of the Kennecott Copper Corporation has presented unique problems for the Drilling and Blasting Department, In order to better understand these problems, a' picture of the Bingham Pit might be helpful. Some quarter of a million tons of ore and waste must be blasted daily in order to keep thirty-eight electric shovels operating. All material is blasted by "toe holes" of 24 to 28 feet in depth, drilled from prepared drill grades and sloped so as to bottom approximately 5 feet below the bench level. Horizontal spacing of these holes averages 22 feet, with exceptions being made where faults occur in the bank. These "toe holes" are drilled by 4-inch drifter machines, mounted on self-contained mobile drill units using .3-inch starter bits and bottoming at a minimum of 2 1/2 inches in diameter, "Toe-hole" drilling amounts to about two-thirds of the total drilling. In the higher bank sections of the Mine and wherever necessary, single rows of "down holes" are drilled to 28 feet in depth and spaced, on the average 23 feet apart. These holes are also drilled by a mobile drill. "Down hole" drilling amounts to about one-third of the total drilling.

Jan 1, 1959

By Heinz C. Dittmar

The phenomenon of radioactivity has been known since the turn of the last century. Scientists of many nations, intrigued by the strange effects of radioactivity, have engaged in research to probe the heretofore presumed, but largely unknown world of atomic structures and subatomic- particles. A theory evolved of splitting the atom, thus providing insight into the structure of matter and opening the way to possibly create new materials. Many years of effort culminated in the first chain reaction in 1942. The beginning of the atomic age was drastically demonstrated by the flash of the large scale chain reaction of the first atom bomb. It was actual proof of the incredible energies contained in matter.

Jan 1, 1966

By R. Quintero

The HYL Direct Reduction Process was the first in the world to operate successfully at industrial scale. The results were so innovative and attractive that other steelmaking companies acquired licenses for the HYL Process. Now in its 40th year of commercial operation, the HYL process has evolved into a modem, highly efficient and economical technology -HYL III. The technology offers high productivity, minimum energy and water consumption, electricity co-generation, raw material flexibility, premium quality DRI/HBI, and is highly versatile for meeting the specific needs of each user. A historical review as well as recent developments and future plans are presented in this paper.

Jan 1, 1998

By Karin Bäppler

Lyon with half a million inhabitants is the third largest city in France. Urban agglomerations such as Greater Lyon demand intelligent underground solutions for the freedom of mobility of its inhabitants. The city and metropolitan area of Lyon provide an example of a city strategy adapted to the changing needs due to demographic and living standard trends. The Lyon Metro Line B with a length of 2.4 km is one of the strategic projects with regard to city planning and future mobility. The paper will highlight on this special area of application in singular diverse geology with sophisticated mechanized tunnelling technology.

Jun 13, 2021

By Bruce L. Bryson

In the past decade a principal growth area in refractory technology has been the development and use of extra high alumina refractories. The refractories user is asking for, and is prepared to pay for, higher purity, more dense materials with longer life, less maintenance, and better dimensional tolerance to meet the exacting demand of high output processes. High alumina and bauxite refractories are being used more and more to keep pace with the demand for guaranteed performance. The steel industry, for example, is starting to place great reliance on these products. A unique material now available with all the requirements for extreme purity and density is tabular alumina, already proving itself in many refractory applications.

Jan 1, 1973

By William J. Halvorsen

We are currently doing work on three ways to improve the performance of our froth flotation systems. One development is the use of a cationic flocculent added to the feed of the froth cells. This does give some improvement in ash of the product particularly in a situation where there is a good bit of clay present. Difficulty is usually experienced with clay carrying over with the water contained in the froth product and also adhering to the coal surfaces. Addition of the flocculent to the flotation feed preferentially flocculates the clay causing it to drop into the tails. The results of some laboratory test work on Pittsburgh 88 Seam coal in Eastern Ohio is shown in Table 1. [ ]

Jan 1, 1979

By K. L. Wiley

In-situ leaching, initiated in 1986 at San manual, was economically developed in 1989. The primary reason for this lag time between startup and viable production was the time required for technical development. The technical development pursued comprised detailed design, development, and implementation of in-situ well construction methods, formulation of suitable well pattern arrays, and the development of extensive hydrogeologic and geochemical knowledge of the mineral deposit. Since 1989, the in-situ leaching program has become a viable and cost effective method to extract copper from the supergene mineralized zone of the San Manuel deposit. The in-situ leaching methods that are currently utilized have been progressively expanded and continually developed and will became the cornerstone of copper production from the San Manuel oxide mineral deposit. This paper presents an overview of the supergene hydrogeology, current design techniques, drilling methods and well completion, pump determination and setting, solution management, and future plans for the increased extraction of copper by in-situ leaching methods at the San Manuel mine.

Jan 1, 1993

By F. M. Doyle, J. P. Dwyer

Introduction The mining industry has a poor public image. It is often perceived as a despoiler of the landscape and a polluter of the environment, and there is little recognition of societal needs for the raw materials and fuels that this industry produces. There are many reasons for this poor image, but an important one is that a substantial number of mining operations have caused significant damage to the environment. Many of these operations, particularly those that now are abandoned, continue to have an adverse impact, principally in the form of water pollution.1 In some cases, the damage caused by this pollution extends well beyond the immediate region around the mine. Chemical contamination of ground and surface waters can, and does, occur in nature when these waters flow through or over undisturbed, mineralized rock masses. However, the problem is greatly exacerbated by mining because the mining activities increase, by several orders of magnitude, the permeability and the surface area of rock that can be contacted by percolating water. Water flowing through either the mine workings or the waste rock dumps becomes contaminated. Pollution can also arise if leachate from tailings ponds enters either groundwater or surface waters. This leachate may contain chemicals used in processing the ore. The magnitude of the threat posed by mining wastes depends on the type of minerals in the deposit, and on the chemicals used to process the ore. The magnitude of the threat also depends on two other, site-specific factors. One is the volume of water flowing into the mine and through the dumps, which depends on rainfall patterns, topography, and whether the mine workings are surface or underground. The other is the proximity of the pollution source to groundwater or surface waters, which depends on both the climate and geology. These factors influence the concentration and the quantity of polluted water forming and reaching the receiving water. Mining activities present a potential problem of enormous scale. Vast amounts of rock are mined each year2 and, as noted above, substantial problems have arisen at some mine sites. These problems are usually exceedingly costly to address, and it is imperative that these mistakes not be repeated. There are indications that we can accomplish this goal; we now better understand the processes that cause pollution and have methods to prevent or contain it. In addition, in the past few decades society has started to recognize the need for all industries to operate in a manner that maximizes the health and safety of workers and the public and minimizes adverse environmental impacts. A variety of recently enacted federal and state laws regulating public health and environmental hazards reflect the increasing concern over these issues. Many statutes, such as the federal Clean Air Act and the Clean Water Act, encompass activities undertaken by the mining industry. Other laws, such as the Surface Mining Control and Reclamation Act, have been written to regulate specific hazards posed by this industry. At the present time, the federal government. through the Environmental Protection Agency (EPA), and several state governments, are preparing new regulations specifically tailored to control the disposal of mining wastes. Given the magnitude of the potential environmental and health risks posed by disposal of mining wastes and the regulatory costs to the mining industry (both of which are due to the tremendous volume of waste generated), it is especially important that regulators have a good understanding of the different types of mining wastes and the risks they are likely to pose in various geographic and climatic circumstances. Only then can a regulatory program be designed with suitable procedures and substantive criteria to protect the environment and ensure compliance, while avoiding unnecessary or wasteful expenditures. California has long enjoyed a large, active mining industry. Today it produces a wide range of mineral commodities. The revenue from production of non-fuel minerals in California ($2.85 billion in 1988) greatly exceeds that of any other state. About a third of this revenue is from the production of inert sand, gravel and crushed stone. However, the remainder is from the production of a wide range of materials. These include boron minerals, rare earths, asbestos, talc and pyrophyllite, and gold. In earlier decades, an even broader range of minerals was produced, including mercury, copper, lead, zinc, and barite. There are acute environmental problems at some of these early mine sites. Because in 1987 the state of California was engaged in a revision of its regulations for mining waste disposal, the legislature commissioned a study by researchers at the University of California at Berkeley to investigate and review: the magnitude of the problem posed by these wastes, • the best feasible control measures available for waste management and disposal, • the problems of abatement and cleanup at so-called "problem" mine sites, • the current regulations imposed on mining waste disposal by various federal, state, and local agencies and the effectiveness of these regulations. This paper summarizes the principal findings from this study (Mining Waste Study, 1988). The lessons from this investigation are likely to be of general interest because of the diversity of mineral products produced, and the wide range of geographic and climatic conditions encountered. The acute problems seen at some of the older mines are typical of the western United States, and teach useful lessons on strategies that should be implemented at new mines to prevent recurrences of these problems.

Jan 1, 1992

By R. Mulyanto, M. Siray, A. Parhusip, F. Hartono

"PT Freeport Indonesia is preparing the Deep Mill Level Zone (DMLZ) mine to be the successor of the currently operating Deep Ore Zone (DOZ) mine. The DMLZ is block cave mine situated 500 m below the DOZ mine and approximately 1600 m depth from surface. Both of the block caving mines require draw point construction in the extraction level to extract the ore from caved area above. Learning from the experience in DOZ, the construction & maintenance of draw points in the production panels is a significant challenge in supporting consistent production.The average DOZ draw point construction duration is approximately 46 shifts per draw point. The time frame for construction is dependent on several variables; availability of the conventional forming system, material availability, and development tolerances. The repair of concrete floors and lintel sets causes production downtime. Reviewing the old DOZ draw point design, there is an opportunity to increase constructability, durability, and reliability of DMLZ draw points. This paper discusses how the DMLZ has improved draw point construction productivity and is on track to significantly reduce costs whilst increasing the quality by using the Six Sigma Improvement Method.Introduction The DMLZ Mine is part of the PT. Freeport Indonesia (PTFI) future Expansion to its underground mining complexes. It is the fourth vertical lift in the East Ertsberg Skarn System (EESS) deposit (Figure 1).Currently, it is under development phase.The DMLZ mine will be a block cave mine using an advanced undercutting method. The DMLZ extraction level will be approximately 1,600 meters below the surface on the 2570 level with column heights of roughly 500 m. The Undercut is on 2590 level, some 20 meters above the extraction level."

Jan 1, 2016

By Annan Cook

J.R. Atkinson, office engineer to Kennecott Copper Corp., summarized data on the Mineral Park area [Wallapai (Chloride) Mining District, Mohave County, Arizona, Fig. 1] and submitted it to the New York office in 1950. He recommended an examination. Weston Bourret, a Kennecott geologist, accompanied by B.S. Butler, the well known former US Geological Survey geologist, examined the larger of two hydrothermally altered areas in Mineral Park that same year. Bourret recommended that the property be optioned and mapped. Georges Ordonez, Kennecott's chief geologist, after a field examination, agreed with Bourret's conclusions At the end of the summer of 1951, Annan Cook (another Kennecott geologist) accompanied Ordonez to the property prior to starting a mapping program. At Ithaca Peak, the structure, alteration, and reddish-brown coloring in leached cavities-hematite, jarosite, and goethite with minor copper staining - made an interesting target. The Peak, which has since been mined, was a Laramide quartz monzonite porphyry grading into quartz porphyry, penetrating Precambrian rocks. Turquoise had been mined from several workings on the Peak. Surrounding the central area of alteration, but mainly to the northwest, there were many long-abandoned underground workings mined for zinc, lead, gold, silver, and copper. To the west of Ithaca Peak within the main area of alteration, surface evidence of a chum drill hole suggested interest in the disseminated mineralization probably prior to World War II. A topographic and geologic survey of the altered Ithaca Peak area was initiated by Cook in September 1951. He was assisted by Richard Vosburgh, field engineer, and by four geologists: Charles Goddard, III, Donlon LoBionda, Keith Martin, and A.T. Stone. When Cook returned to New York, Vosburgh was left in charge. Mapping continued and diamond drilling took place during the winter of 1951-1952. Drill sites were selected entirely on the basis of surface geology. Five drill holes, including a flat hole, located around the flanks of Ithaca Peak, averaged about 183 m (600 ft) in length. A sixth hole caved at less than 60 m (200 ft). The best values obtained were in the first hole (-45°): 90 m (300 ft) averaged 0.62% copper and 103 m (337 ft) averaged 0.041% molybdenum. In another hole, 43 m (142 ft) averaged 1.09% copper and 0:023% molybdenum. The values of copper and molybdenum in these two holes were generally higher than in the remaining holes, although molybdenum values were always around 0.024% or better. The New York office decided, however, to abandon the project even though the remaining field crew of three had recommended more drilling.

Jan 1, 1991

By Andy B. Wallace

Veins in the Pyramid district of northwestern Nevada occur along steep fractures in Oligocene and Miocene quartz latite tuffs. The vein mineralization is zoned from a central enargite-pyrite zone outward through a complex polymetallic intermediate zone and an outer zone of galena and pyrite. Wall rock alteration includes advanced argillic and sericitic envelopes along veins superimposed on district-wide propylitization. The ore distribution and alteration patterns were probably produced by an increase in pH, a decrease in sulfur fugacity, along with cooling of the migrating hydrothermal fluid.

Jan 1, 1978

By Paul H. Rydlund

The wide use of bulk ANFO in surface coal mines is questionable in our energy conscious environment. At many locations, bulk ANFO is not the proper economic selection. Water conditions, energy requirements, waste and spillage, and vibration control are factors too often overlooked in the proper choice of blasting agents. Cost savings over 20% have been realized by converting bulk ANFO to packaged blasting agents. Future trends suggest greater concern for energy conservation in blasting will limit bulk ANFO applications and promote packaged products where quality can be maximized, waste and spillage eliminated, and water compatibility in wet areas assured.

Jan 1, 1980

By Jr. Wilkinson

In today's work environment a tremendous amount of data is required to provide the regulatory agencies justification to issue a mining permit. The demands for data, specifically environmental characterization data, grow and the mine plans must address the issues raised by the interpretation of that data. Computers and computer software can provide operators and consultants with the tools necessary to assimilate, digest and interpret these seemingly unmanageable data sets. This paper presents some examples of how Mincom's MineScape software can be applied to the task of developing coal mine permits in an electronic format.

Jan 1, 1996

By F. Robert Hollo

Programmable controllers have achieved remarkable acceptance over the relatively few years since their introduction. They provide some unique advantages over conventional relay and solid-state logic, which they often replace. Programmable controllers are discussed in both conceptual and functional terms, followed by an exploration of their applicability to material handling tasks with particular emphasis on conveyor systems.

Jan 1, 1973

By L. M. English

When plotted as head vs. volume, fan curves start high and decrease in head with increasing volume while mine head curves start low and rise with increasing volume. Their intersection is the system operating point But wait a minute: Isn't head loss a negative number, a debit? And isn't fan head an energy addition, a credit? This, as every ventilation instructor knows, is often a stumbling block to student or audience comprehension. It is possible to use the intuitively correct curves -pressure losses as negative values and energy additions as positive values -and still obtain the correct operating point: adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at \\tIich the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure; with the standard approach it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel circuit or ventilation net\wrk. The results are the same, and the approach is logically consistent and less confusing.

Jan 1, 1997

By Joao B. Cardoso

This paper describes a two-stage reverse flotation method developed at the Mineral Resources Institute (MRII, University of Alabama, for Kerr-McGee Corporation (KMC), to separate the trona (Na2CO3 ? NaHCO3 ? 2H2O) from a saline deposit containing halite, borax, minor salts, and water insoluble materials. In the first stage, trona is depressed with Quebracho, and the insoluble gangue is floated with fatty acid. In the second stage, trona is floated with cresylic acid. The flotation concentrates contained better than 90% trona with insolubles ranging between 1 and 2%. Although the trona recoveries were low, optimization and middlings recycled in a continuous circuit could substantially increase the value.

Jan 1, 1989

By Gordon S. Thomas

The problem of how best to exploit a reserve has vexed mine planners and design engineers since mining began. The cyclic nature of the mine design-scheduling problem, combined with the lack of good mathematical tools for tackling it, have ensured that it has been, and will continue to be, a major challenge for operations researchers working in mining. This paper reviews the current state of the art in pit optimisation and scheduling algorithms. Starting from the inception of the first block models in the late 1950's, it progresses through the developments and applications of the Moving Cone algorithm, the Lerchs Grossmann 3D Graph Theory algorithm and some of the heuristics, to the new artificial intelligence techniques that are being applied today. Along the way, it discusses the limitations of the various approaches and lays the foundations for the research that is currently being undertaken by CSIRO and others in the field of mine production scheduling and control.

Jan 1, 1996

By Osvaldo A. Bascur

The implementation of continuous quality improvement is the confluence of Total Quality Management, People Empowerment, Performance Indicators and Information Engineering. The supporting information technologies allow a mineral processor to narrow the gap between management business objectives and the process control level. One of the most important contributors is the user friendliness and flexibility of the personal computer in a client/server environment. This synergistic combination when used for real time performance monitoring translates into production cost savings, improved communications and enhanced decision support. Other savings come from reduced time to collect data and perform tedious calculations, act quickly with fresh new data, generate and validate data to be used by others. This paper presents an integrated view of plant management. The selection of the proper tools for continuous quality improvement are described. The process of selecting critical performance monitoring indices for improved plant performance are discussed. The importance of a well balanced technological improvement, personnel empowerment, total quality management and organizational assets are stressed.

Jan 1, 1995

By D. E. Munson, T. M. Torres, D. A. Blankenship

The Thermal/Structural Interactions (TSI) In Situ Tests are a series of large scale, well instrumented tests that have been constructed at the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico. As a precursor to the TSI tests, a ventilation drift (Room D) was mined, drilled and instrumented. This room provided the contractor an excellent area to practice controlled construction methods and was a proving ground for construction monitoring and documentation methods. All gages in this first room have been monitored since their initial installation, which has provided a small, but representative, data base. These data also were the first to be available from any TSI area for analysis. This paper discusses the construction activities in Room D and the data generated from the construction and drilling. Deformation of the room is compared briefly to numerical calculations that used a rather simple creep model as a reference. The constitutive model for salt, it appears, must be improved before it can predict the underground deformations.

Jan 1, 1986