Search Documents

By William J. Dimond

Computor analysis has opened a new world of information for the mining of resources. This paper is directed at the mining of coal. The same procedures apply to most mining projects. The available facts when evaluated against the variables produce the answers. The project must be carefully analyzed, so that the facts can be organized in a data file. The file can be expanded as additional information is obtained during the entire life of the mine. If the mine is pre-planned, the file will be expanded in an orderly fashion and updated information will be available at all times. The development of a property goes through several phases; Exploration, Economic Analysis, Development, Production, and Reclamation. Each phase is an expansion of the data file. The validity of the answers is directly related to the accuracy and quantity of available data. The basis for a data file is horizontal position, and elevation of each piece of information. A coordinate system and datum are reference for a digital (X, Y and Z) position in a spatial system, a three dimensional digital model of the mine. The current practice is to use the State Plane Coordinate system and elevations as established by the U. S. Coast and Geodetic Survey. Each state has adopted this system by law. In the event there is litigation, it is an advantage to have the data on the legally recognized system. The control must be expanded so that all data can be assigned a digital position, and planned to fulfill the requirements for all phases of the mining operation. The project must be analyzed to insure that the objectives can be achieved without duplication or loss of time. sufficient data must be available to reach each required level of information. The coal data can be defined in two categories, spatial

Jan 1, 1977

By Karl Gunnar Holter, Frank Clement

"INTRODUCTION Typically waterproofing of conventionally excavated tunnels has been done by installing pre-fabricated sheet membranes between the primary temporary support lining and the secondary permanent inner lining. The membrane acts as a separation or sliding layer between the linings, which is often desirable. The geotextile installed behind the sheet membrane provides the required drainage and protection of the system. The design of the tunnel lining is strongly influenced and limited by the use of waterproofing sheet membranes. Since primary and secondary linings are separated from each other, forming a double-shell lining system. In that case the secondary lining must be designed for all permanent loads, although the sprayed concrete primary lining continues resists ground and water loads for a long time after construction. Significant progress has been made in sprayed concrete technology over the last two decades, with advanced admixtures, as well as the improved application technology using spraying robots. The development of new admixtures like superplasticizers based on poly-carboxylates, alkali free accelerators and silica fume, enables designers to use permanent sprayed concrete linings (SCL) increasingly for long-term service life. When designed and applied correctly, sprayed concrete can be considered as permanent. The use of spray applied membranes has seen increased use over the last decade in some countries, and demonstrated functionality and cost-effectiveness in several situations. This paper describes the use of the sprayed waterproofing membrane MasterSeal 345, an EVA polymer based product, and the practical experiences from several projects. SPRAY APPLIED WATERPROOFING MEMBRANES The sprayed waterproofing membrane is polymer based and has been especially developed for underground structures. The membrane is applied between primary and secondary concrete linings and develops high bond strength on both sides to the concrete (doubled-bonded)."

Jan 1, 2016

By Brian W. Hester

Ore was first discovered at the Kidd Creek mine site during the first few days of December 1963 when a diamond drill hole there cut sulfide mineralization. This event marked the end of the search started 11 years earlier with the conception of a geological idea. Economic forces provided the stimulus needed for the application of this idea but other-events, and legal considerations, also played arole in delaying the ultimate discovery. The location of Kidd Creek is shown in Fig. 1. Management of the then Texas Gulf Sulphur Co. had become concerned in 1951 at the company's declining reserves of native sulfur in Texas. This problem was to be alleviated by new discoveries and development of methods to recover sulfur from sour gas. At the time, however, the solution appeared to lie in the recovery of sulfur from pyritic ores. Canada was chosen as the best country in which to find these ores. Walter Holyk was hired in 1951 to conduct the search. By 1952, he was working in the area near Sherbrooke, Quebec, known as the "Eastern Townships" where mineralization consisting of base metal sulfides in volcanic rocks has long been known. His observations here led him to the then revolutionary conclusion that such mineralization could have formed as part of the volcanic process and not, as was generally supposed at the time, by replacement. On learning of the discovery of similar mineralization near Bathurst, NB, he moved there in the spring of 1953. He was able to utilize his new concept and found the Half-Mile Lake sulfide deposit.

Jan 1, 1991

By A. D. Hoagland

There are large areas on all of the continents with environments which are favorable for deposits of zinc and lead of Mississippi Valley type. In the developed countries, these environments have for the most part been quite thoroughly explored for the near surface deposits, and it will be necessary to direct more effort to the search for deeper buried deposits from which much of our future production must come. The difficulties of exploration for deep ore of this type are many and formidable, but the area of permissive environments beneath deep cover is many times as great as the area of the known near surface ore districts. It is a reasonable assumption, therefore, that numerous deposits wait for discovery and development. The finding cost, however, is certain to increase, and it is essential that concepts and techniques of exploration be improved if we are to sustain a reasonably strong productive capability into the 21st century. Exploration for deeply buried deposits requires at the outset relatively large areas of favorable geologic environment. The favorable horizons must be within economic limits of depth for the exploration as well as for the mining techniques which are currently available; and there must be some condition, design or strategy which will assure the explorer a reasonable chance of obtaining maximum benefit from discoveries which he may make.

Jan 1, 1973

By Robert J. Wise

The mine plan for an underground longwall mine plan usually requires a longwall panel conveyor that begins operation at its maximum length and gradually shortens over the life of the panel. Current mine plans around the United States require initial panel conveyor lengths of up to 4500 m (15,000 ft) and capacities of up to 3.2 kt/h (3500 stph). Because these conveyors are constantly being moved from panel to panel, their components must be as compact and light as possible, and the design must be flexible enough to be modified as new terrain and conditions are met. In the past, when drive horsepowers or belt tensions were exceeded due to conveyor length, a new flight would be added, including additional belt storage units. In some cases, this led to as many as three flights installed in a single longwall panel. As the longwall retreated through each flight, mining was required to stop during removal of the drives and storage units. This sometimes meant several days of lost production. Intermediate drive technology was developed to eliminate this excessive downtime and still keep conveyor belts, motors, pulleys and other components as small as possible. With intermediate drives placed along the carrying side of the conveyor, belt and motor sizes are kept as small as possible, and only one storage unit is needed. Most importantly, as the longwall retreats through a booster drive station, it can generally be removed in a regular downtime slot and no additional production time is lost.

Jan 1, 1993

By A. E. Raddatz

The U.S. Department of the Interior, Bureau of Mines, is investigating methods for recovering tungsten from domestic resources. A calcine-quench-leach (CQL) technique was developed for the extraction of tungsten from the Golconda, Nevada, hot springs ores. The deposit contains disseminated tungsten, which cannot be beneficiated by conventional techniques and must be treated by hydrometallurgical methods. The CQL procedure consists of calcining the ore at 900° C for 3 hr, quenching in a solution containing 1.5 parts of NazCO3 and 1.5 parts of NaOH per part of WO3 in the ore and at a solution- to-ore ratio of 3 to 1, leaching at 200° C and at 250 psig for 3 hr, and filtering and washing the residue. A series of closed-circuit batch tests showed that 92 pct of the tungsten was extracted from a sample containing 2.32 pct WO3. The pregnant solution contained 11 q of W03/1.

Jan 1, 1982

By Dale C. Matthews

The Getchell Gold Hine is located about 40 miles northeast of Winnemucca, Nevada. Gold was discovered at the mine in 1934 and production was started in 1938 and ended in 1967 for its first phase of operation. Gold production during this period was about 800,000 ounces. In 1983, FirstHiss Gold Inc. purchased the property and initiated an exploration program that proved minable reserves of about 1,300,000 ounces of gold remained in the mine. During the exploration period, metallurgical testing was conducted to determine the most economical process that could be utilized for recovery of gold from the very refractory ore. After extensive investigation, pressure oxidation of the ore was selected, Engineering for the new plant commenced in 1987 and construction was completed in 1989 at a cost of about $87,400,000.00, not including financing cost.

Jan 1, 1990

By A. T. Yu

The quest for ore in an open pit is fundamentally an earth moving proposition. This thesis is vividly underscored by the rapidly increasing volume of waste to be removed in newer mines, where in some instances waste to ore ratios have reached as high as 20 to 1. Continuing depletion of high grade reserves, greater demand for raw materials, coupled with ever climbing labor costs, have made the problem still more pronounced and the need for more effective means of earth moving in an open pit even more acute. A conservative approach to the problem has been to upgrade the sizes of conventional earth moving equipment such as shovels and trucks. In many open pits, particularly in the C.S., this has been responsible for the generally down- ward trend of earth moving costs. None the less, the investment costs of these machines are high, and their gigantic engines are seldom fully utilized. Moreover, a large number of operators are required and maintenance remains relatively high. Unfortunately most people have felt that no other viable alternative was in sight within today's technological capabilities.

Jan 1, 1973

By Lloyd H. Yeager

Good morning gentlemen. I'm very pleased to be a part of this fine program for the Society of Mining Engineers. Gypsum, as many of you know, is one of the most unique minerals on earth. The very excellent presentations which you have just witnessed, revealed the geological aspects of gypsum operations. It is not our purpose this morning to pursue this subject further. Instead, we felt you would be interested in some of the uses of gypsum . . . and what the future holds for gypsum products. To help accomplish this, we're going to first show the Gypsum Association's new film, "Shape Of The Future. ' This short movie traces gypsum f ram mines and quarries to its ultimate destination in homes, schools, offices -- in virtually every type of construction. We think you'll be particularly interested in the description of gypsum's fire resistive nature.

Jan 1, 1965

By Amoussou Coffi Adoko, Shevaune Zeng, Sebastian D’Hyon, Gareth Kennedy, Eleonora Widzyk-Capehart

Inertization of coal dust with stone dust is a common control implemented within underground coal mines to mitigate the hazard of a coal dust explosion. To achieve adequate inertization, the total incombustible content (TIC) of the coal/stone dust mixture is required to meet certain percentages depending on the risk and relevant legislation. Current methods for determining the TIC of a mixture involves laboratory analysis, colorimetric comparison, or the use of portable instruments. This paper provides preliminary analysis of determination of a sample’s TIC in real-time with chemometric modelling, using portable instruments employing near-infrared (NIR).

Feb 1, 2024

By Gerald H. Luttrell

The determination of mass balances is the first step in analyzing the performance of processing circuits. Although conceptually very simple, the mathematics associated with mass balances can be cumbersome when conflicting data sets and/or complex circuits are evaluated. Fortunately, many of the spreadsheet programs available today include powerful search routines which can be adapted to solve common mass balance problems. To demonstrate these capabilities, a generalized mass balance program has been developed using the Microsoft Excel? spreadsheet. Compared to commercial programs, the spreadsheet format is user-friendly, more versatile and easier to customize. This paper reviews the mass balance problem and describes how spreadsheet tools can be used to reconcile conflicting data.

Jan 1, 1996

By G. R. Doubek

Dual Tube Reverse Circulation (DTRC) drilling has been extensively used for collecting groundwater information for the dewatering program at Amax Gold Inc. Sleeper Mine. This paper presents a discuss ion of the types of data which can be collected from DTRC drilling, as well as the effect submergence has on the data. A simple low-cost method of injection testing has been developed using DTRC equipment, allowing quantitative data to be obtained from exploration or test holes. Potential yields can be determined for each drill location, allowing siting and design of production wells to be optimized.

Jan 1, 1992

By Nasri Munfah, Raymond E. Sandiford

"Superstorm Sandy (Sandy) created a storm surge that inundating many of the tunnels that pass beneath the Hudson and East Rivers. The tunnels are vital infrastructure links for the economy of New York City and the northeast region. The sea water, which contains highly reactive salts, caused significant damage to electrical and mechanical systems. In addition, the salt water inundation left corrosive precipitants on the tunnel linings and on and within electrical duck banks. After the salt water was evacuated from the tunnels, condition assessments were performed using a state of the art approach involving high resolution laser scanning, digital imaging, and thermal imaging. These scans were performed prior to hands on inspections. The damage assessment concluded that, although the tunnel structural linings were not damaged, the interior elements of the tunnels needed major rehabilitation to arrest the continual deterioration of the structures. This paper details the state of the art approach used for these tunnel inspections. INTRODUCTION On October 29, 2012 Super Storm Sandy flooded a large number of both transit and vehicular tunnels in the New York Metropolitan area. The region’s transportation network was severely disrupted. The storm damage is estimated to have been in excess of $30 billion, and with the tunnels out of service, the local economy was losing hundreds of millions in economic activity. Restoration of these tunnels was a very high priority and the resulting expedited restoration process did not always provide adequate time for comprehensive condition surveys. This resulted in many of these surveys being conducted after service restoration. Inspecting highly trafficked transit tunnels is challenging and the logistics of working in short night outages led to a rethinking of the conventional inspection approach. Traditionally, visual and tactile methods are first used to inspect tunnels and then quite often followed by LiDAR (Light Detection and Ranging) scanning and perhaps infra-red scanning. For multi-mile tunnels, the time required to visually map tunnel features can be quite extensive. By performing the scanning first and then performing the visual and tactile inspections, one is able to use the scan data to identify the specific areas that need detailed inspections. This approach was used quite successfully for a number of the NYC tunnels."

Jan 1, 2016

By C. C. Hatch

As part of a general project to simulate a concentrator, the Brenda Mines Limited secondary crushing plant, located near Peachland, B. C., was sampled during the summer and winter of 1975 to develop a digital crushing plant simulator specific to the Brenda operation. The purpose of this simulator was to study the influence of manipulable process variables on important responses and to permit study of alternative circuit configurations if desired. This paper describes the simulation methodology employed and presents the results of a computer study of the secondary crushing plant (1).

Jan 1, 1979

"HISTORY Tube bundle systems have been used in the coal mining industry for gas detection since the 1960’s. At the time there were developments were underway for improved gas monitoring systems. The primary gas detection systems in use were the flame safety lamp, colorimetric stain tubes and the taking of samples for analysis by gas chromatography. The MSA D6 hand held methanometer was approved in the UK for statutory methane measurements in 1972 and became very popular due to its smallness and simplicity of use. In 1973 Sieger Limited also developed a BM1 methanometer which could be installed underground and relay methane concentrations to the surface. Similar developments were underway for carbon monoxide detection and one was developed in 1982 by the Yorkshire Regional Laboratory of the NCB commercial development was undertaken by Sieger Limited who named it the ‘SCO1’. The UNOR 1 carbon monoxide and methane analyzers were approved for underground use in the United Kingdom in the late 1960’s.5 The technique was developed by Dr Luft of Bergbau-Forschung Essen and the equipment was manufactured by Maihak in Germany. The apparatus was flame proof and provided an intrinsically safe output which allowed the result to be telemetered to the surface through colliery communication systems. Both analyzers work on the same principal and each of the gases adsorb a certain wavelengths of infrared radiation. The detector measures the residual transmitted radiation and determines the percentage of gas present in the sample. These flameproof versions had proven to be robust and reliable. The UNOR 1 had been used in the Saar region of Germany and Scotland in the UK. The development of tube bundles for hydraulic controls enabled the development of the tube bundle gas monitoring systems we know today. A bundle of tubes are taken underground through a shaft, a borehole or drift then distributed to the required monitoring points. This enabled the ongoing monitoring of the underground environment when the power was isolated at 1.25% CH4. In 1972 the United Kingdom (UK) National Coal Board (NCB) produced a hand book for tube bundle systems which was subsequently updated in 1974. This is a useful guideline into the operational aspects of tube bundles systems at coal mines6. Many of the processes identified are being followed today. The United State Bureau of Mines (USBM) prepared a circular similar to the NCB handbook on tube bundle systems.7 The circular was prepared by Litton C and it was targeted at the design criteria for tube bundle the systems. The circular also states that “pneumatic monitoring systems can be used to monitor for hazards that develop quite quickly”."

Jan 1, 2016

By O. M. Wicken

Magnesite has the unique combination of properties that make it useful in a wide variety of metallurgical applications. The use of refractory magnesite has been increasing throughout the world, but the source of the "ore" differs. The United States has increased production of synthetic magnesites while the rest of the world is exploiting its resources, using natural magnesites. The history and methods of manufacturing synthetic magnesite are discussed as well as the practices for beneficiating natural magnesite. The properties, costs, and uses of the two types of magnesite are discussed and compared.

Jan 1, 1964

By M. Yekeler

The critical surface tension of wetting values (Ye) of realgar (AsS), talc [Mg3si401o (OH) 2]' stibnite (Sb2S3), and sulfur (S) were determined by flotation in the absence of conventional flotation collectors as 38.7, 38.0, 35.5, and 30.0 dyne/cm, respectively. The surface tensions of flotation media were arranged by methanol. Separation of binary mixtures of these minerals was performed exploiting their Ye differences-which form the basis of the "ganuna flotation process". One step flotation test showed that sulfur floats preferentially from its mixtures with realgar and stibnite at recoveries of 73.6 and 70.7 % and grades of 81.7 and 91.2 %, respectively. The separation of stibnite from realgar gave a recovery of 4.1 % and a grade of 41.2 % for stibnite, indicate that a minimal Ye difference of 3.6±0.2 dyne/cm is essential for such separation when conventional flotation reagents are not used. This paper presents data and describes the approach employed in these separations.

Jan 1, 1994

By T. J. Durbin

At some surface and underground mines, control of ground-water inflow involves significant costs. These costs include the capital costs for installing a dewatering system, power and other costs to operate and maintain the system, and costs to treat and dispose of the water that is collected. To minimize these costs, design of a dewatering system utilizing wells has been formulated in terms of a nonlinear operations research problem using quadratic programming. Using this formulation, the locations, depths, pumping rates, and pumping schedules of wells are selected so as to minimize the total costs of the dewatering system.

Jan 1, 1993

By A. P. Wickland

The characteristic problems related to drilling a hole for evaluation of an orebody are generally quite similar, whether we're drilling a core hole, or a hole to obtain chip samples. The basic objective in each case is fundamentally an economic factor; to produce the maximum amount of usable information per hole at a reasonable footage price. The success of the drilled hole depends largely upon the amount of investigation and research spent on the prospective area and the ability to forecast the capable personnel needed plus the right kind of drills, ancillary equipment such as bits, muds and various additives necessary to make the drilling program successful. The driller is confronted with a wide variation of drilling problems due to the nature of subsurface conditions. Some of these problems are: overburden, which may consist of clays; sand; boulders; or glacial till. These surface conditions may exist up to 2,000 feet in depth and upon reaching bedrock, formations may consist of swelling shales, broken sandstones, and every conceivable rock-type, coupled with every known structural problem such as dips, faults, folds, etc., and to this added extras such as permafrost and/or ground water problems combine to increase the necessity why an understanding of the problems along with the proper reaction of the driller plus the formula to compensate for ground conditions is necessary to complete a drill hole. Since most geologists are familiar with diamond core drilling techniques, I would like to discuss other methods used in evaluating ore deposits.

Jan 1, 1973

By Ulf Marklund, Manfred Lindvall

Fighting the challenge of diminishing ore grades, low base metal prices and a changing pattern of ore supply, Boliden has now taken the second generation of the fully­autogenous grinding concept on stream, Using new design and a highly-developed process control system the benefits of conventional two stage autogenous grinding technology are obtained with a wide range of ore types. The APC grinding system has been developed further. A new design of the Boliden Pebble Extractor together with an advanced control strategy make the performance of the APC concept superior to all other grinding systems with any ore quality. The capacity and simplicity of the autogenous grinding concept is equivalent to the best SAG installations but the operational costs are up to 25 % lower than for SAG or other primary ball or rod mill systems. The concept is as flexible as conventional crushing and rod mill installations but investment and operating costs are of the order of 25 % lower. Also, from the metallurgical point of view, the different types of autogenous grinding system outperform all other comminution systems including SAG. From 1989 to 1991 four fully autogenous grinding sections have been installed at various concentrators at the Boliden company. Old crushing plants and rod and pebble grinding circuits have finally been replaced by highly productive and cost-efficient autogenous grinding equipment. Significant savings in operational costs have already been reported. Power consumption and maintenance costs have been reduced significantly. Productivity expressed as milled tonnes per operator has been improved. Metallurgical results have developed favourably.

Jan 1, 1992