Search Documents

By J. Wright

Since the 1960’s toroidal conductivity has been used to determine the Alumina to Caustic ratio of the digester discharge liquor stream. In recent years the application of ceramic materials have allowed the sensors to moved upstream to provide tighter control of the process. In the Bayer process, dissolving the aluminum contained in bauxite ore in caustic soda and converting it to aluminum oxide produces alumina. An important parameter of the process is measuring the alumina to caustic ratio in the digester discharge stream. The A/C ratio at a given caustic concentration is a measure of the degree of saturation of the alumina in the plant liquor. The aim in the process is to achieve a high A/C ratio. There is however a limit where precipitation will occur if the A/C ratio is too high. For many years conductivity has been used to determine the A/C ratio. Conductivity of discharge liquor is related to the caustic concentration. The change in the caustic concentration is in the same direction of the change of solubility of the alumina. Controlling the conductivity through adding additional bauxite ore and varying the dilution flow can increase plant yield.

Jan 1, 2001

By T. J. Batchler

Deformable materials are sometimes added to ventilation stopping constructions to prevent damage caused by convergence in coal mines. However, adding deformable materials can significantly reduce the capacity of a stopping to resist transverse loading. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) has conducted research on the effect of various materials with different deformation properties on the transverse loading capability of a stopping wall. Based on a three-point hinge method of failure, a half-wall method of testing in the NIOSH Mine Roof Simulator was used to simulate full-scale wall behavior. This simulated the fracture initiation and eventual failure of the stoppings from transverse loading. The impact of the modulus of elasticity of various deformable materials was examined in this study. A polystyrene foam block with a low modulus of elasticity, which is commonly used as a deformable material, was shown to degrade the transverse load capacity of the stopping by as much 95%. Other materials with higher modulus of elasticity preserved more of the transverse load capacity of the stopping, but were not able to absorb as much convergence. This paper presents the results of a parametric study that quantifies the impact of various deformable materials in block stopping construction under transverse load conditions. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Joseph Clare, Elizabeth Anderson, Mike McGinley, Ron Hines, Judy Cochran

The South Lake Union Pipelines contract for King County Wastewater Treatment Division and Seattle Public Utilities in Seattle, Washington included three 1.8 m (72-in)inside diameter microtunneled pipeline segments totaling about 793 m (2,600 lf).Tunnel alignments were within street right-of-way of heavily traveled urban roadways. Project challenges recognized in the design included: high groundwater levels; contaminated soil and groundwater; variable soil conditions, including fill; and timber piles and other obstructions remaining from historic land uses. The tunnels were built using a Lovat MTS Microtunneling machine, beginning in spring 2003. Conditions encountered during construction presented additional challenges beyond those anticipated in the design process, and were successfully addressed by the owners, designer, and construction management consultant all working with the contractor. Problems included highly variable soil conditions, cracking of reinforced concrete pipe joints during pipe jacking, a timber pile trestle uncovered during shaft construction, and obstructions encountered in the second and third microtunnel runs.

Jan 1, 2005

By Steve Kral

Invensys is a London-based supplier of automation and control systems to a variety of manufacturing and processing industries. Through its global subsidiaries, Invensys provides customized, advanced process control systems and networks for automating industrial plants, including mineral processing plants. The company employs more than 80,000 people worldwide in its four divisions. They include Automation, Control, Powerware and Software Systems. These four divisions work together to design the complete package for their customer’s automation and process-control needs.

Jan 1, 2002

The propensity of coal spontaneous combustion can be evaluated using various laboratory testing methods such as R70 adiabatic tests, thermal gravimetric analyzer (TGA) and critical self-heating temperature (CSHT) methods. Each of the methods has its unique characteristics and index for classifying the propensity of self-ignition of coals. Accountable relationships among the propensity indices of different methods should be established. Using the newly established R and TGA testing setups in our ventilation laboratory, samples from US coal mines have been collected and tested. 70 The TGA is a relatively new quantitative method. A test can be conducted in a relatively short time. The temperature and weight of the sample can be measured with high precision and then used to determine the activation energy of the coal which is a good indicator for potential of self-heating. Under a specific experimental design, the TGA technique could perform the proximate analysis for determining coal quality parameters (e.g., moisture, volatile matter, fixed carbon and ash content). These parameters can be used in an empirical equation for assessing the potential of coal self-ignition. The trend of activation energies determined using TGA techniques and adiabatic tests are reasonably consistent with each other. As a case study, a comparative analysis of these two methods for determining activation energy was made on coal samples collected from Indiana. The kinetics of the spontaneous combustion mechanism has been explained. If the functional groups of a coal are easier to be activated with a small amount of activation energy at a relatively low temperature, the coal will has a higher potential of self-heating. With the kinetic and coal quality parameters determined by the TGA setup, it has been found that the coal with low potential of self-ignition has low self-heating rate, high activation energy and high minimum self-heating temperature.

Jan 1, 2012

By Paul D. Tomlingson

During the next several months, SME’s E-Newsletter will feature 15 articles on maintenance management. The articles may be read online or downloaded and distributed within your organization. They will address maintenance management topics, offer guidelines to mining managers and provide techniques that the maintenance manager can use. The articles will stress equipment management, a strategy that the mining industry has accepted as a modern replacement for outdated maintenance practices. Equipment management is the mutually supportive interaction of all mine departments as they establish equipment needs, procure equipment, test, commission, operate, maintain, modify and eventually replace equipment. The successful application of equipment management principles can quickly and reliably produce cost reduction and performance improvement results while providing a dependable way of sustaining them. Equipment management embraces modern management techniques. These include reliability-centered maintenance, life-cycle costing, capital performance, the effective use of information and productive organizational models.

Jan 1, 2003

By David Young

This paper presents tunnel design considerations for the SR75/282 Transportation Corridor Project in Coronado, California. The project is managed by the City of Coronado in cooperation with Caltrans and the US Navy and may include a one-mile long twin-tunnel section with two options: a 36.5 foot diameter twin-bored tunnel or a twin cut-and-cover box. The alignment crosses the Coronado Fault, and design provisions were needed at the fault crossing to maintain life safety and prevent rapid inundation of the tunnel in the event of fault rupture. These provisions are discussed along with considerations related to liquefaction and ground shaking. The project is currently in the planning stage with construction to start around 2012.

Jan 1, 2008

By Thomas Gregor, Brian Garrod

As the popularity of precast concrete segmental linings for tunnels is growing in North America, some problems related to grouting of, and near, these linings are starting to appear. The installation of a segmental lining behind a TBM requires that the annular space around the lining be quickly filled with grout to prevent collapse of the ground. In practice, the filling of the annulus is frequently delayed and takes place a distance behind the machine typically via grout ports centrally located in the segments. If partial collapse of the annulus has occurred, it may become necessary to use higher grouting pressures in an attempt to distribute the grout. There have been several occasions where these increased pressures have caused damage to the tunnel linings. Similarly, compaction grouting adjacent to a tunnel lining can cause damage. This paper quantifies the effects of such grouting on a typical precast lining.

Jan 1, 2005

In conjunction with steady increases in production levels, longwall operators have applied greater quantities of ventilating air and spray water in an effort to control respirable dust and/or methane. Air velocities greater than 7.6 m/s (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high velocities. The greatest likelihood for entraining dust into the high velocity airstream may occur as shields are advanced allowing relatively dry particles to fall from the shield canopy directly into the airstream. Laboratory tests to simulate dust liberation during shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH at velocities ranging from 2.0 to 8.2 m/s (400 to1600 fpm). Airborne dust samples were obtained with personal impactors to quantify the size distribution and concentration of the dust entrained at the various air velocities. Statistically significant increases in both total and respirable dust concentrations were measured as test air velocities were increased.

Jan 1, 2001

By Scott G. Britton

Microcomputeranalysis has long been a technique for engineering professionals to improve the theoretical and practical design of continuous mining systems. Such work has been typically composed of modeling observed events and then introducing a variety of known elements with predicted results to compare against the results of the model. Programs written in BASIC, Cobol, Fortran or other language dominated such efforts. These programs have taken years to develop and prove out. This article explores a new management tool used daily at Tanoma Mining Co. (TMC) to track and improve continuous mining systems through the use of microcomputers and Lotus l-2-3 software. Data provided by section foreman, shift foreman, and maintenance personnel are analyzed against predetermined goals. In this way, new production targets are developed, weaknesses in the current mining systems are identified, and the results of changes are measured. The current results of this system on the productive output of TMC systems is on the order of 10% improvement. Thin seam coal mining is an industry within the broader industry of coal mining. Thin seam mining faces the same cost pressures and engineering problems as its higher-seam competitors without the advantages of moving volume per foot of extracted material to stay at an economic parity with others requires additional creativity within the management teams to extract higher productivity gains from the existing workforce and mining systems. TMC operates a deep mine in Indiana bounty, PA, about one hour northeast of Pittsburgh.

Jan 1, 1991

By A. Duerksen

"Surface coal mining in West Virginia has supplied energy to the eastern coast of the United States for over a century. Over the years, the coal mining industry has been forced to adapt as societal demands regarding health, safety, and environmental impacts have changed. More recent pressure has called for another iteration of change: long-term post-mining sustainability. The research discussed in this paper investigates one potential solution - or component of a solution - to improve the sustainability of surface coal mining in West Virginia: post-mining wind power. The paper begins with an introduction to the Appalachian region of the U.S. and the role that mining has played in its history, followed by a discussion of the need for sustainable mining and how post-mining wind power may help fulfill it. Data processing methodology of field data from monitoring locations is then explained. The results are then used to estimate the electrical output of a wind turbine. This data is then utilized in a case study discussion of one of the monitored sites. The paper concludes with an analysis of the broader implications of the research and a discussion of future work."

Jan 1, 2011

A dedicated tunnel construction version of the Caterpillar 328D LCR compact radius excavator is proving highly productive on the A9 Autoroute construction project near Visp, in Switzerland. It is the first machine of its kind to operate on a Swiss contract and uses a special dedicated front attachment designed and constructed by German Caterpillar dealer Zeppelin. The machine offers a powerful, stable and compact solution for tunneling contractors. A rear overhang of just 305 mm (12 in.) provides a tail swing radius of just 1.9 m (6.2 ft). The 328D LCR is ideal for the restricted working areas within a tunnel construction site. The machine is equipped with the wide tracks from the 330D L conventional crawler excavator, ensuring maximum stability when operating. In addition, the boom mounting has been moved further toward the center of the machine for the tunnel model, creating an increased lift capacity over the front end compared with a standard 325D L. The boom itself features a robust box section construction, with high-strength steels, additional supporting struts and reinforced bearings for maximum durability. All pins have hard-chromium plating for optimum protection against wear. Stick digging force is a powerful 134 kN, with up to 212 kN of bucket digging force available, for maximum penetration in blasted material. The 328D LCR is also equipped with a heavy-duty dozer blade as standard. This ensures outstanding stability when working and providing a useful secondary tool for clearing and leveling within the jobsite. Two 45° tilting mechanisms in the boom construction, allow the boom to be swung to 45° on either side of the machine. So the specially designed attachment linkage provides increased rollback for access to the roof of the tunnel. A Caterpillar CW45S mechanical quick-coupler allows rapid changes between specialist tunneling attachments, standard Caterpillar buckets and a range of Caterpillar work tools. The machine is powered by a Caterpillar C7 diesel engine. This six-cylinder EU Stage IIIA diesel motor [ ] offers 8 percent more power than its predecessor, with 140 kW (190 hp) available at just 1,800 rpm. Caterpillar?s ACERT combustion technology results in lower fuel consumption and reduced exhaust emissions. However, the tunnel machine is also equipped with a diesel particulate filter as standard, to further cut exhaust gases within the tunnel working. The 328D LCR is designed for use in transport tunnels of 6.8 m (22.3 ft) in height. With the tunneling boom in place, the machine has an operating weight of 42,540 kg (93,783 lbs), yet retains a transport height with the tunnel boom of just 3.9 m (12.8 ft). Transport width with 600 mm (23.6 in.) track shoes, is just 3.2 m (10.5 ft). On the A9 tunnel contract, the machine is being used by a consortium of Swiss and Austrian companies working for the canton of Valais? Routes Nationals Construction (RNC) department. The 31.8-km (19.7-mile) A9 Autoroute construction project will connect Sierre in the west and the town of Brig to the east. The tunnel that is bypassing the town of Visp is just one of a number along the mountainous route.

Jan 1, 2009

By K. G. Kebkal, R. Bannasch

"Because the operation of tethered underwater vehicles in the deep ocean or under drifting ice areas is very complicated or impossible, the application of autonomous underwater vehicles (AUV) is preferred or even the only possible solution. However, this implies the possibility of a direct and real-time control over all AUV functions, which is only achievable with the availability of accurate positioning/navigation and a high-speed communication link. This paper presents a flexible bottom- or surface-based solution enabling high positioning accuracy of underwater objects (harvester, AUVs, bottom nodes); specifically, a multifunctional system that combines Ultra Short Baseline (USBL) transceivers and Long BaseLine (LBL) stations deployed at a large depth. Moreover, each baseline transponder is equipped with a high-speed communication device to provide the means for real-time AUV control based on the information about its current position, e.g. navigate it with direct commands and operating its actuators and other mechanisms. Moreover a communication link with a high data rate can provide valuable visual information from the operation area.Depending on how many nodes the LBL grid comprise has, target transponder positions can be estimated with an accuracy of several to tens of centimetres. The purpose of the paper is to present the experiments with all key elements of the multifunctional Hydro-Acoustic USBL-aided LBL Positioning and Communication System."

Sep 1, 2014

By James M. Harrington, A. Azra Bilgin, JoAnn Silverstein

The prevention of AMD in situ is more attractive compared to subsequent downgradient treatment alternatives that do not involve source control. AMD source control can be achieved by shifting the microbial activity in the sulfidic rock from pyrite oxidation to anaerobic heterotrophic activity. This is achieved by adding biodegradable organic carbon amendments to the sulfidic rock. This technique was applied in an abandoned mine pool with a pH of 3-3.5. Following treatment, near-neutral pH and decreased effluent heavy metal concentrations were achieved. In situ bioremediation by enhancement of bacterial iron and sulfate reduction is a promising technology for AMD prevention.

Jan 1, 2005

By D. McBride

Representative samples are required from process streams in order to accurately measure chemical and physical characteristics. This information can then be used by process operators and metallurgists to evaluate the process and effect control actions for the operation. The capture and presentation of representative samples can be critical to measuring values, such as elemental analysis and particle size, with on-line or near-stream analyzers. A comprehensive multi-physics model has been developed and used to better understand the effects of slurry flow and particle segregation under certain operating parameters. An algebraic slip model coupled with a free surface algorithm is used to track motion and position of particles and phases within a specified geometry.

Jan 1, 2009

By Jacek Paraszczak

Numerous problems encountered in the mining of narrow vein deposits challenge the productivity, competitiveness and profitability of many mines. Mechanization of mining operations is one of the most important means to ensure the healthy survival of this mining sector. Vein deposits account for nearly all the world's primary silver production, as well as a significant portion of gold, tin, copper lead and zinc. In North America, narrow vein mining constitutes an important sector of the industry. Operators exploiting such deposits are concerned with the most appropriate mining method and equipment to mine in such a way as to minimize waste rock dilution. Unfortunately, most of the equipment available does not meet the additional geological and economical restrictions typical of narrow vein mining. Thus, mining these deposits is labor intensive and can result in low productivity. Consequently, the profitability of many such mines is reduced. Increased mechanization is one of the solutions to ensure their healthy survival. This paper reviews the state-of-the art in mining equipment with reference to narrow vein mining limitations. Problems encountered Geological conditions and economical factors have a decisive impact on the choice of mining method and equipment. Many ore bodies are relatively small, usually erratically distributed, often less than 2 m (6.5 ft) wide, with dips ranging from 0° to 90°. To make things worse, ore body limits are sometimes difficult to determine and the ground is hard and abrasive.

Jan 1, 1992

By Don Hickey

The MTA in conjunction with LIRR, are in the process of expanding one of the largest commuter railroads in the country, with over 260,000 passengers a day. The LIRR, which provides 700 passenger trains every 24 hours, can?t continue on the present growth course as a joint tenant in Penn Station with Amtrak and NJT. For this reason, in conjunction with the fact that over 53% of LIRR?s current riders into Penn Station are ultimately bound for the East Side of Manhattan opening, have created the need for the expansion of the LIRR. The complete expansion will cost approximately 6.3 billion dollars and all of the contracts are to be completed by 2013.

By G. Deschênes

Following a successful investigation on the Central Zone sample, a cyanidation study was conducted on an ore sample from the AD-MW Zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. At a grade of 6.48 g/t, gold is present in the forms of aurostibite, free gold and electrum. The ore contains 4.3% berthierite/gudmundite, 1.3% pyrrhotite, 0.7% pyrite, 0.07% stibnite and 0.9% arsenopyrite. Similar to the Central Zone, the extraction of gold from the AD-MW Zone can be performed at atmospheric pressure, pH 10.5 and with a low concentration of cyanide. The grind size had no effect on gold extraction between a P80 of 28 to 71 µm. The oxygen and cyanide requirement significantly increased with a ?ner grind. Consequently, a very close control of cyanide addition is required to minimize passivation of gold. Lead nitrate, added in the pretreatment, increased the extraction of gold by 2.3%. Leaching at pH < 10 improved gold extraction but increased the cyanide consumption by 5%. Passivation of gold occurred when the pretreatment was longer than 2 hours. A longer pretreatment reduced the cyanide consumption by 5%. Mineralogical characterization of the leach residue with no gravity pretreatment prior to leaching indicated the presence of unleached gold grains and passivated gold grains. Removal of coarse gold by gravity increased the extraction by 2.8% (leach residue at 0.74 g/t Au). Increasing the DO to 16 ppm or the lead nitrate from 500 to 1,000 g/t increased the overall gold extraction to 90.4% (leach residue at 0.62 g/t), which is the maximum gold extraction obtained. The leaching parameters were 800 ppm NaCN, DO 16 ppm and pH 10.5 for a duration of 120 hours. The associated cyanide consumption was 4.0 kg/t. Gold leaching was not sensitive to cyanide concentration. Reducing the cyanide concentration to 250 ppm resulted in a gold extraction of 89.5% with a cyanide consumption of 2.6 kg/t.

Jan 1, 2009

By Tim O’Neil

Question: Looking forward, do we face a future in which energy markets, energy policy and energy conflicts threaten to preoccupy, if not dominate, our concerns over economic growth, national security and domestic tranquility? The answer is, we may indeed face such a future. Question: What oil resource is comparable in size to the reserves of Saudi Arabia and presents a tremendous opportunity? The answer, the oil sands in Alberta, Canada. Question: What is the largest mineral staking rush in North American history, still under way? It has so far led to the development of two large mines. The answer is the Point Lake diamond strike in Canada’s Northwest Territories. It led to the development of the Ekati and Diavik mines.

Jan 1, 2004

By R. Shields

"Hard rock mines move large volumes of material, which can cause the conveyors that are essential to this movement to suffer lots of problems, including carryback, spillage, dust and belt wander. Many of these issues are created at the transfer points where the belts are loaded.This article provides an overview of the latest transfer point systems that incorporate safety and serviceability by design as well as a report on recent projects. One project is the Conveyor B Transfer at the Coeur Rochester silver mine near Lovelock, NV. Here, performance was improved with the installation of belt support cradles, engineered chute walls with external wear liner, and a compact dust collector. A second project is the improvement of belt support idlers and skirtboard sealing in a long loading zone of a conveyor under the concentrator at an Arizona copper mine.The importance of transfer pointsConveyors are essential in mine material handling. Their performance will often make the difference in mine productivity and profitability. A key to conveyor performance is the transfer points where the conveyor belt is loaded and discharges. At these transfer points, many of the problems encountered with the conveyor system are created.The problems that arise at the transfer stations include off-center and segregated loading, mistracking, blockages and plugging. And there are a variety of problems originating with fugitive material — cargo released in the form of carryback, spillage or airborne dust — that are created or exacerbated in the transfer points. These fugitive materials turn into other conveyor-related problems, including shortened component life, unplanned outages for conveyor maintenance, unexpectedly high labor costs for maintenance and cleanup, worker health and safety problems and issues with community relations. The U.S. Mine Safety and Health Administration estimates that 85 percent of conveyor maintenance is a result of fugitive material at conveyor transfer points.Technologies to improve transfer pointsA number of techniques to improve the performance of conveyor transfer points have been developed. They include:"

Jan 11, 2017