Search Documents

By M. H. Al-Dabbagh

In this paper, the authors outline the deficiencies of PERT/CPM as a method for scheduling complex projects such as mine development. In particular, PERT/CPM networks cannot accommodate logical nodes (events) or stochastic branches (activities). The Graphical Evaluation and Review Technique (GERT), developed by Pritsker and. co-workers, is introduced as an alternative to PERT/CPM that overcomes many of the deficiencies of the latter and enables a more realistic analysis of complex projects that are subject to significant uncertainties. A brief overview of GERT network structures and network analysis is given and a PC implementation of the method is described. The technique is illustrated by application to the development of an open-pit gold mine in Saudi Arabia.

Jan 1, 2002

By D. Antonov

The physical and mechanical properties of coal play a important role in the planing and design of coal mines. However, due to the complexity conditions in situ and the influence of unknown factors, it is hard for people to evaluate the physical and mechanical properties of coal directly. In this research, uniaxial compressive stress was used to change the attribute of coal samples, and the ultrasonic measure technique was used to evaluate the physical and mechanical properties of coal. The results of laboratory test showed that there was a strong relation between uniaxial stress and velocity of ultrasonic wave. Sensitivity analysis with numerical simulation was used to define the relation between the physical-mechanical parameters of coal and ultrasonoc wave. With the dynamic analysis module of FLAC, three elastic and plastic models were built to model the coal samples. The modeling parameters were changed pro rata, and the correlation of coal and ultrasonic wave properties were summarized and presented. The result from this research will be base for further analysis of caving behavior of coal.

Jan 1, 2010

By J. C. Reid

Computer-aided lithogeochemistry was used to "prospect" for stratabound scheelite (a tungsten ore) that occurs in many Precambrian clastic and chemical rocks, northeastern Brazil; The district is a metallogenic province covering about 5000km2. Exploration bedrock lithogeo-chemistry was applied at regional, local, and mine scales to identify regional tungsten trends and dispersion halos associated with economic tungsten mineralization. Regional coarse-mesh sampling (Cu,Mo,W) in 25km2 cells "found" all major mines and significant prospects using objective and cost objective computer mapping of bedrock geochemical data. The method is efficient ; of the 3600km2 study area only 9% of the original area remained after the initial pass. Of this area, the geo- chemically highest ranked (4%) cells contained the mines and prospects. Similar computer-aided treatment was applied to Cu,Mo,W,F, and Be lithogeochemical data from several mining concessions and prospects with outcropping and subsurface W mineralization. At a local scale out-cropping W mineralization was recognized at a distance of 500m. Fracture zones through which hydrothermal solutions traveled were identified; these were related to W mineralization at a depth of 200m.

Jan 1, 1986

By S. Jennings

The Red Dog massive sulfide deposit is located in the western Brooks Range of Alaska 100 miles north of the village of Kotzebue. It contains the largest zinc reserve in the world. Reserves were doubled in 1995 with the discovery of the Aqqaluk deposit and significantly increased in 1996, with the discovery of a deep zone of mineralization to the north. At present the global reserve and resource is 143 million tonnes of 16.1 % zinc and 4.3% lead. Red Dog is a silica + sulfide synsedimentary replacement deposit hosted in barite and black shale of the Mississippian Kuna Formation. Red Dog was thrust northward during the late Mesozoic Brookian orogeny. Understanding the setting of the deposit at the time of formation and its subsequent deformation history is critical to current exploration efforts and to future discoveries in the district.

Jan 1, 1998

By Richard J. Wilson

The importance of coal as a major source of energy used by the steel industry has been increasing due to the gradual changeover from steel- making by the open hearth process to steelmaking by the basic oxygen process. Since the production of steel by the BOF process increases the demand for hot metal, there is a growing need to ensure the supply of coke required for the production of hot metal. Coal used for cokemaking has become, therefore, an increasingly important raw material for the steel industry in recent years. Our current projections indicate that coal will be the source of 71% of the total energy requirements of Inland Steel Company in 1985. As a result of the energy shortages of the last few years, various conservation programs have been initiated by the steel industry to reduce the consumption rate of fuel. The efforts to conserve energy have been successful to a great extent due to the rapid advances made in the technology of ironmaking that facilitated gradual reductions in the quantity of coke used per ton of hot metal produced in the blast furnaces. The decrease in the consumption rate of coke was made possible by the use of improved raw materials, such as iron ore pellets and fluxed agglomerates, the operation with high blast temperatures, the injection of auxiliary fuels, and the enrichment of the blast with oxygen. It is expected that additional reductions in the fuel consumption rate will be possible in the ironmaking operations of the large blast furnaces that are being equipped with facilities for proper burden distribution and for operation with higher blast temperatures at high top pressure. The purpose of this paper is to show the effects of coke quality on the production of BOF steel. The importance of coke quality will be pointed out by discussing the effects of the physical strength of coke on both the blast furnace productivity and the steelmaking operations of an integrated steel plant, such as Inland Stee1 Company.

Jan 1, 1980

By D. C. Panigrahi

The paper presents the development of a thermodynamic based network analysis model. It uses transient heat flow algorithm for computing the heat flow from strata and predicts the environmental condition in different branches of the network. Along with the environmental condition, the mass flow distribution in network is computed by using nodal pressure method based on linear theory approach. The algorithm has been coded using object oriented programming approach and it has been validated in actual field condition. The correlation is satisfactory.

Jan 1, 1997

By A. D. Shuloyakov, V. A. Zukerman, G. A. Finkelstein, V. I. Kurets

Possibilities of electric pulse disintegration are discussed with emphasis on high selectivity of the process as compared to mechanical comminution methods especially when applied to polymineral ores. Physical explanation of this phenomenon is suggested. The authors present results of some experimental tests illustrating regularity of this phenomenon irrespective of origin of ores or dissemination pattern of valuable minerals including both dissipated and accessory minerals. Some operating plants applying this principle are described the plants used either for mineral research purposes or for obtaining pure monomineral fractions or for treatment of gems to be faceted. Obstacles for implementation of this technology are mentioned.

Jan 1, 1995

By Sunil Jain, Jan M. Mutmansky

As coal mining evolves in this country, underground coal is being mined at greater depth and under more difficult conditions than in the past. At the same time, economic conditions make it necessary to mine more efficiently and economically. As a result, pressures on mining companies arise on two fronts and make the job of mining coal underground very difficult. Recent improvements that have been made in health, safety and productivity have come about primarily due to improvements in existing technology and better management of all the production resources. However, this trend can continue only so far and thus innovation will be needed to continue the improvement. This paper deals with a concept that, on the surface, appears to be more efficient in terms of the costs to provide ventilation. The resulting design is oriented toward increasing the ventilation efficiency through use of a unidirectional ventilation plan but it also promises to increase recovery and decrease the requirements for development entries. To analyze this ventilation concept, two mine layouts with a similar production schedule were planned in a hypothetical 1.83 m (6 ft) coal seam. The first alternative analyzed uses a traditional approach to ventilation with centrally located shafts and a bidirectional ventilation pattern. Using this system, it is necessary to use large-diameter shafts and a large number of main entries. Using the same assumptions on ventilation requirements, the second alternative utilizes unidirectional ventilation whenever possible, a smaller number of main entries and small-diameter blind-bored shafts in the bleeder areas. The comparative analysis is performed using PSU/TDMVS, a computer network analysis program that is capable of determining the ventilation power requirements at any time in the mine life and converting the costs to a present value. The economic analysis is then completed by including the shaft-sinking and entry-driving costs and the costs associated with the recovery of coal that are directly related to the change in the ventilation system. The results are summarized on a present-value basis.

Jan 1, 1987

By George F. Weaton

During the past eight years there has been a dramatic change in the iron ore industry of Minnesota, in that its status has changed from that of a seller's market to a higly competitive buyer's market. Minnesota's natural ores must now be beneficiated and up-graded considerably to be marketed in order to compete with the higher grade foreign ores as well as with the locally produced and highly desirable taconite pellets. With the passage of the "Taconite Amendment' in the November, 1964 election, the taconite industry commenced to expand in Minnesota, which, although initiated in that state, was benefiting many other states and some foreign countries to a much greater extent than Minnesota. These other areas were actually appropriating markets that had been established and retained by Minnesota for many years. Since the approval by the state voters of this amendment, there has been a great increase in the development of taconite properties on the Mesabi Range.

Jan 1, 1966

By Z. T. Bieniawski, D. A. Newman

The Geomechanics Classijication (RMR System) (Bieniawski, 1979) was modified for entry and roof support design in underground coal mines. Adjustment multipliers were introduced to incorporate the influence of high horizontal stresses and the roof support reinforcement into the existing classification system. Sixty- two case histories of standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant im- pact on the stand-up time of supported coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1987

By Richard Dunmore

Most coal seams in the United Kingdom contain firedamp, some of which is released into the ventilating airways as the strata around a working relax. The close sequence of seams in carboniferous strata is usually such that seams in adjacent roof and floor strata are also disturbed and potentially large quantities of firedamp can enter the workings from these sources. Since emission depends on the disturbance rate of the seams, higher coal production rates associated with increased mechanisation in the colliery accentuate the problem. Firedamp concentrations in UK underground workings are subject to statutory regulations1. To enable production to continue uninterrupted and in safety the problem is tackled by ventilation engineers by the provision of adequate ventilation in the airway and by the technique of firedamp drainage. In the UK the latter usually takes the form of cross-measure boreholes in roof strata, and increasingly also in floor strata, drilled from the gateroads, especially from return airways. In this way firedamp emitted from disturbed seams in adjacent strata can be extracted directly to the surface or to some safe position outbye, and the airways of the working district are not contaminated. Despite the use of firedamp drainage, considerable quantities of firedamp enter the ventilation air- stream and the concentration levels may be seen to be related to the coal production activites in the district. Figure 1 shows a typical recording of methane concentration obtained by a BM1 methanometer at a position outbye in a return gate where firedamp drainage was operating. The general rise in level throughout the working week may be seen, together with peaks occurring during production shifts and the gradual decay of emission over the weekend. In view of the fact that ventilation and firedamp drainage contribute a considerable proportion to the operating costs of the colliery, it is essential that the ventilation and firedamp drainage requirements be calculated as accurately as possible at the planning stage of the working. In the past the ventilation engineer has had to rely heavily on experience in neighbouring workings but with the development of mines in previously unworked areas there is clearly a need for a methodical approach to meet the requirements of planning. The work described in this paper represents such an approach and it is hoped that successful development and application of the method of prediction will lead to the widespread adoption of a routine procedure. The current development of a method of prediction of firedamp emission into longwall workings is based on the theoretical treatment of gas emission from coal seams proposed by Airey2 in 1971, which was based on his study of gas emission from broken coal 3 which was published in 1968. In common with other experimental methods of prediction, the method enables a calculation to be made of the total make of gas emitted from all sources of gas in the strata per tonne of mined coal.

Jan 1, 1980

By P. Tsang

The stability of longwall chain pillars depends not only on the mechanical properties of coal and surrounding rocks, but also geological and mining conditions. In order to evaluate the effects of each, variable, the orthogonal experiment design was employed in this study for significance analysis. The study concluded that the stability of longwall chain pillars is mainly controlled by the ratio of pillar stress to pillar strength, the ratio of Young's moduluds of the roof to coal and floor to coal, entry width, pillar width and the internal friction angle of coal. Additionally, horizontal stress, panel width and mining height also play a significant role.

Jan 1, 1994

By R. K. Singhal

Optimization of a load-haul system for a surface mine involves two processes. The first is proper selection of mining equipment compatible with the minesite job specifications and the second is an efficient utilization of this equipment. All things being equal optimal productivity and cost is achieved when the capacity of the hauling equipment is matched at all times with that of the loading equipment.

Jan 1, 1986

By Enrique Jelvez, Pierre Nancel-Penard

The traditional way of generating open-pit mine production schedules has several limitations. This work addresses the design and production-scheduling problem by considering minimum operational space requirements under a Direct Block Scheduling approach to generate extraction sequences that satisfy the operational space required. For this, traditional formulations were extended by including a new set of constraints that generate operating spaces for mining equipment to move and extract material. Then, a heuristic algorithm produces close to optimal practical pushbacks. This proposal was applied in a case study, and the results show its ability to generate practical production schedules without sacrificing expected return, obtaining differences in terms of Net Present Value (NPV) lower than 1% when compared to the traditional approach.

Jun 25, 2023

By R. Jin

The hydrophobicity of six coals ranked from lignite to anthracite is studied through contact-angle measurements, bubble attachment-time measurements, FTIR spectroscopy, and Hallimond-tube flotation. The preliminary study shows that the hydrophobicity of coals can be told by the bubble attachment times of coals (a kinetic criterion) or by the contact angles (an - equilibrium criterion). A general agreement between flotation response of coals and measured bubble attachment times or contact angles is observed in the present study. However, the study also shows that the hydrophobicity of coals can be predicted by FTIR spectroscopy work with proper manipulation of the spectra. Both hydroxyl and carboxyl groups in the coals are proven by FTIR work to be responsible for the change of coal hydrophobicity. A new criterion for the hydrophilicity index of coals from FTIR spectra is introduced through the study.

Jan 1, 1987

By F. Mensah-Dwumah, W. H. Baker, G. W. Clough

INTRODUCTION The practice of injecting chemical grouts into permeable soils in order to stabilize them for tunnel construction is a common procedure in Great Britain, Europe and Japan. In this technique, the grout penetrates the soil in a fluid condition, but hardens or "sets-up" in about one hour due to a chemical reaction. As a result, the soil, is strengthened and made less pervious, and this, in turn, reduces ground surface movements, limits ground water flow, and controls movements of the heading during tunnel construction. It is only within the last five years or so that this technology has been used in the United States. Most of the applications have been involved in the work for the Washington Metropolitan Area Transit Authority (WMATA) subway construction. The experience gained from this work is, in many instances, unique and should serve to guide use of the grouting technology in future projects. This paper documents five WMATA case histories; information is provided as to the soil conditions, method of treatment, reason for treatment, and tunnel performance. Locations of the five projects covered by this study are indicated in Figure 1. All are within the boundaries of the District of Columbia and involve soft ground tunnel construction. Basic information for the case histories is given in Table 1. Tunnel sizes and depths below the ground surface as well as general soil conditions are similar in all instances. The tunnels are about six meters in diameter and are located so that the crown is five to ten m below the ground surface. The soils typically consist of alternating sand, clay and silty sand strata. However, soil stratification details are

Jan 1, 1979

By P. A. Hendricks

The surface coal mining industry in the United States employs over 50,000 people and is responsible for 60% of domestic coal production. This represents a very significant contribution to our national economy and an important source of highly skilled and well paying jobs. The U.S. Bureau of Mines (USBM) has targeted surface mining as an important research priority to reduce the social and economic costs associated with surface mining injuries and fatalities. USBM safety research focuses on the development of technologies that can enhance productivity and reduce mining costs through a reduction in the number and severity of mining accidents. This report summarizes a number of completed and ongoing research programs that address a broad range of surface mining safety problems. Research methods are described, and research products which are suitable for industry implementation are highlighted.

Jan 1, 1994

By Robert A. Jankowski, Fred N. Kissell

Recent allegations about tampering of coal mine dust samples have led to suggestions that the coal industry needs a respirable dust compliance sampling method that is less subject to tampering. The sampler designs under consideration include fixed location monitors that could be mounted on a mining machine or located at a stationary location in the mine, and samplers that are worn, like the existing samplers. Fixed-point samplers have a design advantage, since samplers worn on the body will have size and weight limitations. On the other hand, in some cases there are respirable dust concentration gradients, which will dictate careful placement of a fixed-point sampler inlet to determine the exposure of workers. This study examined dust concentration-gradient data obtained by the Bureau of Mines and others over the last decade. As an example of spatial gradients at continuous miners, a fixed-point monitor located in front of the operators cab shows a higher dust concentration than a sampler located on the operator and reduced exposure when the sampling location is behind the operator cab. It may be necessary to use a sampling tube with a machine mounted monitor, to sample in the operators breathing zone in the cab to provide a more representative sample of the miners exposure. For face workers on longwalls or on continuous miner sections using remote control, the study shows significant dust level gradients and gradient variations between typical operator positions and mining machine locations. In addition, if fixed-point monitoring is used to monitor an area, vs the exposure of specific workers, dust control technologies currently employed to ensure reduced dust exposure such as the diversion of dust laden air away from the workers, or through the use of remote control of mining machinery may not indicate the same dust reduction obtained with current sampling techniques.

Jan 1, 1993

By William C. Baldwin

Unitization and containerization continue to grow with great rapidity throughout the world today. Every industrial nation outside of the Iron Curtain is devoting more and more time toward research of these developing sciences. Unitization and containerization are proving to be the solution to many of modern industry's most pressing handling and shipping problems. Manufacturers make large savings, carriers receive many benefits, and customers take an increasing interest in demanding that their shipments either be unitized or containerized. Unit-loads consist of items, packages or bulk materials pre-assembled into a convenient mass for handling by mechanized equipment and to fit the internal dimensions of carriers. It has been found that unitized handling and shipping offers cost savings too great to be ignored by anyone interested in the distribution of goods. At present, the benefits from unitized shipping and handling are being enjoyed only to a small extent due to the failure of many persons concerned with handling practices in recognizing only some of the advantages of unitization. Before the full benefits of unitized handling and shipping can be realized, some major changes in packaging and distribution practices will be necessary on the part of industry. Numerous investigations in the last two years show conclusively that there are more advantages and more inherent savings for shipping goods on pallets in unit loads than by any other method. There is no question that unit-load handling can offer significant advantages to the user over piece-by-piece package handling. Reduction in handling costs is the primary objective of such activities, but it is by far not the sole objective. Some of the other benefits that can be realized are:

Jan 1, 1973

By D. L. Monroe

Technical service is assuming an increasingly important role in the sale of asbestos fibre,, Manufacturers are examining raw materials more closely than ever before in order to, obtain the most efficient usage in their processes. Asbestos is one of the more difficult materials to evaluate and consequently has been are of the last to be subjected to evaluation. The main problem encountered in the evaluation of asbestos fibre is that minor differences in grade and texture are not shown up by chemical analysis, and are identified only by specialized physical analyses or actual production use. However, such minor differences become more critical as manufacturing processes are made more efficient, and many purchasing agents and plant chemists are applying a closer scrutiny to their supply of raw asbestos fibre. Many processes have been formulated around grades and qualities of asbestos fibre, which were standard some time ago, but which may now be subject to modification and improvement.

Jan 1, 1959