Search Documents

By H. R. Green

The design of slurry launders has usually been based on strictly empirical concepts. An examination of the most common procedures reveals that they do not account for many of the variables that are recognized as Significant for slurry transport. These may include flow rate, volume concentration of solids, solids specific gravity, solids size distribution particle shape, launder geometry, and roughness of the wetted surface. It was decided to develop a design procedure, which would accomplish two things: First: Take into consideration most of the known significant variables and systematize the procedure to assure consistent results. Second: Provide a rational basis for examining and utilizing operating data to refine and improve the system. To accomplish this, it was necessary to develop a basic design concept. This concept has been developed through a complex development history, and yet still appears workable and technically sound. That concept may be outlined as follows: First: The solids transport velocity is the fundamental basis for slurry launder design. Second: The stream configuration, hence the launder size, is integrated with the solids transport velocity so that the actual stream velocity exceeds the solids transport velocity. Third: The launder slope is that which will achieve the required actual stream velocity. It was originally planned to utilize a series of charts and nomographs for the design procedure. A nomograph, based on data given in Taggart's Handbook of Mineral Dressing (1), was developed to determine the solids transport velocity. The velocity thus determined was used with Manning charts to determine the launder slope .and configuration as though the fluid were water. It was planned to utilize a "slope adjustment factor" to increase the slope to compensate for the apparent viscosity of the slurry. All attempts to develop a suitable correction factor failed. This failure was principally due to the complex relationship of viscosity to the required slope. It was then decided to revise the entire approach. Specifically, the present procedure is based on the Darcy-Weisbach flow equation, which is rationally preferable to the Manning equation. The Camp (2) equation is used for the solids transport velocity. The necessity of reference to the Moody curves for the Darcy friction factor is avoided by using the Colebrook and White (3) equation. The resulting mathematics require iterative solutions for several of the unknowns.

Jan 1, 1978

By W. Zitz

Incorporation of heat exchangers into drilled shaft foundations is a novel approach to both improve the energy efficiency of building heat pump systems and provide necessary structural support using the same construction materials. In an effort to quantify the structural and heat exchange performance of deep foundations used as ground-source heat pumps, two instrumented test foundations were constructed as part of a new construction project in Denver, CO. They will be integrated into the conventional ground-source heat pump system for the building. This paper focuses on the lessons learned from the construction process for these energy foundations.

Jan 1, 2011

By Ebelia Manda, Peter RK Chileshe, Sydney Chinyanta, Abdul Samson, Victor Mwango Bowa

Buttressing is a widely employed control measure for mitigating slope failure in various settings such as openpit mines, road sections, dams, and hilly or rocky terrains. This paper presents a study on the effects of buttressing, specifically concerning slide-head toppling failure. Drawing insights from a case study of slide-head toppling in Zambia, our investigation employs both analytical (limit equilibrium) and numerical (3DEC software) modeling techniques. The analytical and numerical models exhibit notable similarities in their schematics and overall results, revealing a subtle effect of buttressing in controlling slide-head toppling failure. This study contributes valuable insights into the nuanced role of buttressing in slope stability, with implications for optimizing buttress design parameters. While the overall findings suggest a modest influence of buttressing on slide-head toppling failure, further discussions delve into the specific implications and potential refinements for practical applications.

Jan 1, 2025

By Clifford J. Lewis

The role of calcareous minerals in that area of the environmental improvement program involving the control or elimination of sulfur oxide emissions is discussed, and a new concept in gas scrubbing, rendering possible the use of calcareous rocks more extensively for this purpose, is presented. Calcareous rocks are defined as the more common limestones, consisting essentially of calcium carbonate and magnesium carbonate. The effect of magnesium carbonate on the reaction rate of limestones and lime toward sulfur oxides in aqueous scrubbing systems is pointed out. The relative economics of lime- stone versus lime as aqueous scrubbing reagents for sulfur dioxide are indicated.

Jan 1, 1974

By Roy L. Klein

The production of synthetic fuels from coal has been pioneered by South Africa. South Africa made a decision in 1975, due to the threat of an oil embargo, to proceed with the construction of Sasol Two, then followed by Sasol Three. South Africa has large coal but little indigenous petroleum reserves. The indirect coal liquefaction process used by Sasol since 1955 is the only commercially demonstrated method available for producing transport fuels from coal. The new plants consume 27 million tons per year of coal from a single mine that now produces transport fuels in sufficient quantities for energy independence.

Jan 1, 1983

By Louis G. Silano, Aram Grigoryan

Parsons Brinckerhoff is providing engineering services for the Atlantic Avenue Station Complex Rehabilitation and Passageway Reconstruction for New York City Transit. Project reflects current realities and challenges of underground excavation, support, and construction under operating subway tracks and platforms, and under major transportation hub, comprising three subway stations, railroad terminal station, and busy street intersection. The construction requires extensive underpinning of subway structures and operating tracks. This Paper addresses engineering challenges of IRT subway station rehabilitation and passageway reconstruction without interruption of transit operations and street traffic. Total construction cost of the Project is $ 105,000,000.

Jan 1, 2003

By H. P. Schlanger, L. Paterson, B. H. G. Brady, B. E. Hobbs

A novel principle for a waste repository, based on a backfilled thermosyphon as the functional unit, is proposed. Such a unit reduces temperatures and temperature gradients in the vicinity of a waste package and in the repository near field, reducing leach rates from packages and thermomechanical disturbance of the rock mass. Preliminary analyses confirm the mode of performance of the system, and reveal some interesting features of material transport and sealing in backfill and rock fissures. The thermosyphon combines attractively with the prospect of developing a near-field geochemical trap with chemical specificity for radionuclides. It is proposed that a thermosyphon repository may provide superior performance of engineered and natural barriers compared with conventional designs. The achievement of the ability to predict accurately the performance of the thermosyphon, relative to other isolation schemes, will represent a benchmark in the understanding of the absolute performance of any repository.

Jan 1, 1986

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

1.1 GENERALIZED METHODS OF SUPPRESSING THE INFLOW OF GROUND WATER DURING THE CONSTRUCTION OF SHAFTS, DRIFTS AND TUNNELS Various methods are used to prevent or minimize the inflow of ground water into underground workings during their excavation. The two most common methods include freezing the saturated rock and grouting using cement, sodium silicate, polyurethane and/or other chemicals. Each of these technologies for combatting the inflow of ground water is effective only under specific hydrogeological conditions. For example, although the freezing of saturated ground is among the more universally adopted methods, it is designed to provide only temporary protection during construction. Before the saturated rock thaws it is necessary to emplace a waterproof liner which is labor intensive, time consuming, and expensive. Consequently, freezing is used only in exceptionally complex hydrogeological conditions, namely in those cases where the water-bearing strata consist of unstable rock or the ground water has an anomalous hydrochemistry. The classical grouting of saturated rock, carried out from the surface or from the face of the underground workings for the purpose of limiting the inflow of ground water during excavation, utilizes both cement and a variety of chemical grouts. Cement grouting has been regarded as the main method of combatting the inflow of ground water in fractured rock throughout the world. In such countries as the Federal Republic of Germany (FRG), Canada, the Republic of South Africa and Great Britain, cement grouting is the main method of reducing the inflow of ground water during the excavation of mine openings. In Great Britain and the FRG, cement grouting has been used in 80% of all shaft excavations. In the Republic of South Africa cement grouting has been used in almost 100% of all the shafts that have been constructed. The installation of grout curtains into permeable water- bearing strata significantly reduces their permeability and increases the rock strength. Grouting has the greatest effect in fractured sandstones, certain well indurated shales, fractured granites, fractured quartzites, and karstic limestones or dolomites. The following principal factors must be considered when assessing the expediency of grouting rock with cement: the geometry of the network of fracture openings, the saturated hydraulic conductivity of the fractured rock, the hydraulic head acting on the water in the rock, and the chemical composition of the ground water. On the basis of the geometry of the fractures and the thickness of each hydrostratigraphic unit, the characteristics of the cement grout are selected. As a rule, the cementing of large fractured zones with high ground water velocities is carried out using inert fillers (sand, mill slag, loam, loess, crushed limestone), special types of cement, setting accelerators, and high cement concentrations in water. Calcium chloride, soda ash, sodium silicate, sodium nitrate, amino alcohols, tin bichloride, trisulphate nitrate, and lumnite are used extensively as the setting accelerators for cement grouts. In the FRG and Poland, special cement injection compounds that embody a mixture of cement and active cement metal salts, water additives and binding substances are being used for the cementing of saturated zones with rapid ground water velocities. These reagents accelerate the rate of structure-forming reactions. In spite of the wide variety of additives used for cement grouts, the effectiveness of the method in large fractures below the water table is either poor or it leads to a very large consumption of cement due to the erosion of the grout through the cracks before it hardens. At the present time, a large number of cement types and brands are being produced by various countries. These variations permit cementing to be employed in a variety of geological conditions. However, both pure cement grout and grouts with fillers constitute unstable systems with a high water loss rate. Therefore during the grouting of finely fractured rock the cement grout's premature loss of a large amount of free water causes its consistency to increase, whereupon the grout solidifies. Consequently, it inadequately penetrates into the fine fractures of the stratum. In addition the high water loss rate in the cement grout causes unreacted cement particles to remain, which greatly reduces the grout hardness and the resulting rock strength characteristics are weakened. As a result, the binding properties of the cement are utilized perhaps up to 60%. The remaining portion is left in the grout as a filler. All these conditions significantly decrease the efficiency of the isolation effort both with respect to strength and cost. In order to expand the cement grouting method, re- search is being conducted to improve the quality of cement grout, to increase its range of application with respect to permeability control, to reduce its water loss rate and to increase its capacity to withstand the erosive and corrosive effects of poor quality ground water. For example, mixtures of bentonitic clay, carboxymethyl cellulose, aerated sodium sulfide, sulphated alcohol distillery waste, nitrolignin, gip-

Jan 1, 1993

By S. A. Tims

INTRODUCTION The Falconbridge mine ore body extends about 1.6 km (1 mile) in length and the deepest developed ore is on the 6050 level below surface. The ore zone varies in width from a few inches to over 30 m (100 ft) and the average width is 4.9 m (16 ft). Access levels are driven in the ore at 53.3-m (175-ft) intervals. The principal method of mining is overhand longitudinal cut-¬and-fill. Prior to 1962 timber square-set stoping as a secondary extraction method was used for about 15% of the total production. Undercut-and-fill was intro¬duced at Falconbridge in 1962 as a potential replace¬ment for the square-set method in heavy ground. The undercut-and-fill method was developed by Inco in the 1950s, its principal application being to transverse pillar mining. Falconbridge made modifications to this method. A feature of the mine is the No. 1 flat fault which dips 0.79 rad (45°) towards the northeast. The main characteristic of the fault is the presence of large swells of ore directly under the plane of the fault. The ground under the fault area is highly fractured and associated with massive sulfides. In the past, the ore under the fault was recovered, with difficulty, by either tight cut¬and-fill or square-set stoping. In the 1970s these meth¬ods were supplanted to a large degree by the under-cut-¬and-fill method. An advantage of the current undercut-and-fill method which uses cemented fill compared to the cut-and-fill and square-set methods is the reduction of dilution due to better control of the walls. At Falconbridge mine, it is estimated that the grade of ore produced by undercut¬and-fill is improved by approximately 10% over other methods. Where undercut-and-fill is used in very weak ground, a much greater improvement in grade can be expected. Table I shows mining production for 1974. The undercut-and-fill method was first used at Falconbridge during 1962. The first longitudinal stope was prepared for undercutting by laying down laminated beams the length of the stope and installing a lagging mat floor on top of the beams. Unconsolidated tailings fill was poured on top of the mat floor. As the cut ad¬vanced under the floor, heavy posts were placed under the laminated beams at 1.8-m (6-ft) intervals. During 1966, a radical change was made to the method when tailings fill, consolidated with portland cement, replaced the unconsolidated fill. This development eliminated the laminated beams and heavy mat floor and greatly im¬proved the stability of the stope. This system, with minor variations, is currently used at Falconbridge mine. APPLICATION The undercut-and-fill method is used to mine in¬competent ground, sills or floor pillars under mined-out levels, or a block of ore isolated between levels. It is occasionally used to advantage in sequencing produc¬tion from various mining blocks. This is done by mining a block of ore cut-and-fill method and at the same time mining the ore block directly underneath by the under¬cut-and-fill method. The undercut-and-fill mill holes at Falconbridge are either boreholes, stripped timbered raises, or steel mill holes. Boreholes and rock raises tend to slough in heavy and broken ground which increases dilution when sloughing exceeds the ore width outline and also in¬creases the difficulty of moving down to start the new cut. For example, in one installation, a 1.2-m (4-ft) diam borehole sloughed to a size of 3.7 x 5.5 m (12 x 18 ft). The undercut-and-fill method usually requires a mill hole extending from the level below the ore to the top horizon of the ore block. The customary methods of providing a mill hole are: 1) A borehole is driven from level to level through the ore block and a chute installed on the bottom level (Fig. 1). 2) An existing raise is used as a mill hole. If the raise is timbered, a steel mill hole is installed inside the timber and tailings fill poured around the steel mill hole (Fig. 1). 3) An existing steel mill hole, situated at one end of a mined-out stope, is used as the mill hole for an ad¬jacent undercut-and-fill ore block. The mill hole posi¬tion is determined when planning the mining sequence of the first stope (Fig. 2).

Jan 1, 1982

By William F. Brandom

INTRODUCTION Cross, et al. (1974), produced a retrospective study of standard setting for underground miners. This report had two distinct components; i) criteria of importance for the protection of the miners, and ii) economic considerations for standard setting. The methods for setting radiation safety standards reviewed were: dose calculations and consensus methods; epidemiology; pathology; bioassay; animal experiments; sputum cytology; chromosome aberrations; and, the Mantel-Bryan Model. By looking back, the authors intended to enable officials to look ahead in making future decisions based on reasonable conclusions. Now it may be time to consider underground miners' protection from another perspective: are there miners who may be especially susceptible to toxic environments?; and if so, are there any biomedical assays that might be indicative of exceptional sensitivities to toxic substances? The human population is genetically very heterogeneous. The data of Saccomanno, et al. (1973), reveal great variability in individual response to radon daughter exposure and only a small portion of the miner population subject to toxic inhalants develop squamous cell metaplasia (Saccomanno, et al., 1970). The majority of the miner population is either not susceptible or is resistant to the toxic agents. This information suggests the existence of a small subpopulation with increased sensitivity or reduced resistance and underscores the need for indicators from biomedical assays that might prove of value for the detection of such individuals. The heightened awareness of the contribution of pollutants in the environment for the potential induction of mutations and carcinogenesis lead to a profusion of short-term bioassays to circumvent the high cost and time-consuming large toxicity animal studies. Over 100 bioassays across taxa from microbes to man are at various stages of use or development (Hollstein, et al., 1979). Less than a dozen tests currently offer early promise for application to[ in vivo] effect studies of man. Many are still in early development, lack the sensitivity needed for a retrospective or prospective study at current permissible exposures, are impractical to conduct in the field, or are not cost effective. The purpose of this paper is to review some of the bioassays that may now, or in the near term, prove applicable for the detection of individual underground miners with increased susceptibility to toxic agents. Throughout this statement, it is assumed that any single test may give false negatives or false positives and, therefore, a tier of tests should be investigated. The possible tests are in various stages of development; some tests better proven than others with a firmer data base and, therefore, with greater probability of usefulness. Some of the less proven assays are not ruled out if they have practical or theoretical promise as indicators. Table I summarizes the assays critiqued for their potential to monitor the effects of [in vivo] exposure to genotoxic substances. POTENTIAL INDICATORS OF HIGHLY SENSITIVE MINERS Assays of Body Fluids It is desirable to have data on the agent(s) to which subjects are exposed when humans are monitored by biomedical effects. Obviously, to varying intensity, the underground mining environments are monitored for radon daughters and it is recognized that the miners are also exposed to other pollutants, most notably, uranium ore dust and diesel fumes. Further testing for the metabolites of the pollutants can be done on body fluid, urine. [High Performance Liquid Chromatography (HPLC)]: This is a very sensitive method for the detection of mutagenic metabolites in urine. The urine is treated with the enzyme sulfatase and beta-glucuronidase to permit identification of substances that are made nonmutagenic by conjugation as glucuronides. The sample is then passed through an XAD-2 resin column and the absorbed organic molecules eluted with acetone. The sample is then split and evaporated to 1 ml and used for direct chemical analysis using HPLC. One drawback to the test is the inability to measure cumulative exposure, but multiple samples can be obtained and comparison to baseline (control) and exposure samples can reveal qualitative differences as a consequence of exposure to mutagens. [The Ames/Salmonella Microbiological Assay]: The Ames/Salmonella microbiological mutagen test is the most extensively used short-term bioassay, with over 2,600 chemicals having undergone testing by this method (Hollstein, et al., 1979). The method, thoroughly worked out and tested for 10 years, consists of taking the second split urine sample from the HPLC preparation, evaporating to dryness and dissolving in dimethylsulfoxide (DMSO). The sample is then applied directly to

Jan 1, 1981

By D. C. McIntire

The Homer City Station, jointly owned by New York State Electric and Gas Corporation and Pennsylvania Electric Company is a three unit coal fired station. The first two units were put into commercial operation in 1969; the third unit became commercial in 1977. Units 1 and 2 are subject to the Pennsylvania State Implementation Plan (SIP) emission limit of 3.7 pounds of S02 per million BTU. Unit 3, having started construction later, is subject to the Clean Air Act, New Source Performance Standards emission levels of 1.2 pounds of 50-2 per million BTU.

Jan 1, 1988

By Violetta Pavlova

Knowledge of geometrical properties of blocks in a hard jointed rock among other things is of considerable importance for prediction of rock mass behavior and for its exploitation. This paper presents a new approach to obtain the information about percentage of blocks with desirable geometrical properties in a jointed rock mass extending through a large region of interest. A model of a rock mass separated by finite number of systems of parallel plane discontinuities which form discrete blocks is discussed. A computational procedure has been derived to analyze the volume and shape distribution of blocks in the rock mass.

Jan 1, 1992

By H. Sevim

The logic and capabilities of a long-term production planning method for open pit mining are presented. This is a new method that can be used to obtain simultaneous solutions to the four interrelated parameters of open pit mining: mine life, specific blocks to be mined each year, the amount of ore and waste to be mined each year, and the ultimate pit limits. An efficient milling cutoff grade can also be obtained through a systematic analysis. A production plan for a real-life gold deposit is given to illustrate the logic and the capabilities of the method.

Jan 1, 1994

By S. K. Kawatra, S. J. Ripke

Iron ore pellets use bentonite clay as binder at dosages from 0.5to 1.0% (10 to 20 pounds per ton) of moist iron ore concentrate. Bentonite is typically shipped hundreds of miles from Wyoming to the Lake Superior iron ore district. It is therefore best to know how effective a bentonite will be before it is shipped and used to bind concentrate into pellets. Current tests of bentonite effectiveness include: plate water absorption, methylene blue uptake, free swell, exchangeable cations, and glycolated layer expansion. However, these tests have many disadvantages: First, they only measure the ability of a bentonite to expand, disperse, or absorb, not how well it will bond. Second, most of the tests require up to 20 hours to perform. Bentonite only has a few minutes to interact within the concentrate before it is indurated (sintered). These long-term tests may not reflect the true behavior of bentonite. Third, the tests are tedious and often results are inconsistent between different iron ore concentrates, labs, and technicians. Fourth, some of the testing equipment is difficult to procure. Fifth, procedures are often difficult to standardize. In this paper, the Binder Effectiveness Strength (BESt) test to evaluate binders for iron ore pellets is presented that: measures the ability of bentonite to bond, requires only about two hours to complete, is simple and reproducible, and utilizes readily available equipment that has been standardized for decades.

Jan 1, 2003

By Haydn H. Murray

Kaolins and bentonites of economic importance in Australia and New Zealand are described. Clays that are used for structural clay products are not discussed. Residual, hydrothermal, and sedimentary kaolins are utilized including clays associated with coal measures. Bentonites are sedimentary and residual. Very little kaolin and no bentonite is exported presently, but this will change in the near future as transportation costs continue to escalate. Many areas of Australia, in particular, where kaolins are known to occur have not been investigated to determine the quality and quantity of the deposit.

Jan 1, 1982

By C. N. Speltz

The cost of transportation of industrial minerals is frequently higher than the cost of the product. Where a minc, industrial mineral plant. or customer is served by a single railroad, that single railroad, because of lack of competition, may increase rates and/or provide inadequate service so that the economics of that mine, plant or customer are adversely affected, or so that the level of service precludes satisfactory performance. Transloading of industrial minerals from rail-to-truck or truck-to-rail in order to improve economics and sales of product is not new. However, transloading to reduce freight costs or improve inadequate service caused by a lack of competition in the rail industry, is a relatively new concept brought on by the recent mergers of many of the main line railroads, both in the eastern and western United States. For example, with completion of the Burlington Northern/Santa Fe and the Union Pacific/Southern Pacific mergers, the western United States has only two mainline railroads. The industrial mineral producer, in order to reduce the cost of transportation, or increase the level of service, must evaluate potential transloading opportunities in light of higher prices and reduced service brought on by reduced railroad competition.

Jan 1, 1998

By R. Kanniganti, M. Karmis, C. Haycocks

An extensive review of multi-seam under-mining literature was conducted and a data base of case studies was assembled . A critical review of the design principles outlined in this literature resulted in the compilation of specific design criteria for the design of lower seam mines. Analysis of this criteria demonstrated the necessity for a protocol for the design of unsymmetrically loaded pillars. Such a design criteria was developed using finite element methods for a wide range of possible loading conditions. This design criteria can be utilized for underlying pillar design when the loading conditions can be determined. To facilitate using all the under-mining research results by field/planning engineers a Windows TM based software package was developed. This software package contains a multi-seam tutorial, analytical tools and a case history database. The package is user friendly and fully interactive and supported with extensive on-line help. The package contains numerous case studies of multi-seam mines that can be reviewed to facilitate analyses.

Jan 1, 1996

By J. C. Yingling, R. Kumar, J. Sottile

The capability for on-line measurement of the quality characteristics of conveyed coal now enables mine operators to take advantage of the inherent heterogeneity of those streams and split them into wash and no-wash stocks. Relative to processing the entire stream, this reduces the amount of coal that must be washed at the mine and, thereby reducing processing costs, recovery losses and refuse-genera¬tion levels. In this paper, new ap¬proaches for optimal control of the segregation process using time-se¬ries models and empirical distribu¬tions are presented and demon¬strated using field data.

Jan 1, 2000

By F. Bourgeois, J. A. Herbst, R. P. King

The ultrafast load cell (UFLC) has proved to be an exceptionally good device for the study of the fundamental processes associated with the impact fracture of particulate material. A new high- sensitivity UFLC has been commissioned at the Utah Comminution Center for the study of low-impact energy single-particle fracture. The force-time histories of individual fracture events have been measured. The force and energy absorbed at crack initiation have been measured at several particle sizes. The mass specific energy for fracture and the associated breakage function have been determined. The distributions of particle breakage energy and particle strength have been measured as a function of particle size.

Jan 1, 1992

By C. Cassios

EIA is a procedure aiming the elimination of adverse impacts to the environment from undertaken projects. Historically, it starts in 1969 when NEPA (Nat.Env.Prot.Agency) in the US initiated the EIA ? EIStatement. The EIA procedure was adapted by the European Union with the directive 337/85 and in Greece the Common Ministerial Decision 69269/90 enforced it to the Greek legislation. However, mining enterprises in Greece long before the implementation of the European Directive and in accordance to the legislation of the Public Law 998/79 for the protection of the forested lands were obliged to submit EIA?s and get an approval in order to operate in forested areas. The submitted and approved EIA?s and their implementation by the mining companies were among the positive aspects of the EIA procedures. This paper is examining the impacts of EIA?s in the Greek mining industry its positive aspects as well as their difficulties and their role for the reclamation procedure. The technical and procedural aspects which EIA presents for the mining industry are commented, while proposals, for a more flexible EIA implementation for the Greek Environment are also presented.

Jan 1, 2002