Search Documents

By Armando Z. Remacre

The purpose of this paper is to attest the effectiveness of conditional simulation technique's for determining the principal pre-mining control parameters during mine planning. These parameters include: determining the selective mining unit size, the optimum pre-mining grid spacing and the number of mining faces to be used. The research work was developed in an iron ore deposit located in the Minas Gerais State, Brazil. Phosphorus was considered the master control variable for the research work. This paper provides the structural analysis (variography) , a description of the steps the were taken for setting up the numerical model, the kriging studies which were applied to the numerical model and the final optimum grid spacing, block size and number of mining faces.

Jan 1, 1992

By J. W. Wilson, Y. P. Wang, M. H. Erten

The use of water is still the most effective and economical means for dust control in underground coal mines today along with dilution by the ventilation current. Studies have shown that the dust capturing capacity of water is a result of a balance of many intermolecular forces. Surfactants are known to reduce such forces by affecting both the surface tension of the liquid and its interfacial tension against a solid. Surfactants can be added to the water sprays to facilitate the dust capturing capacity. A laboratory scale model has been developed in which surfactants were added to the spraying water and preliminary data indicates positive results.

Jan 1, 1991

By K. L. Whitehead, R. A. Jankowski, N. I. Jayaraman

Most continuous miner sections utilizing flooded-bed scrubbers also use blowing face ventilation. Blowing ventilation, however, interferes with dust capture and minimizes scrubber effectiveness. To enhance the efficiency of the scrubber system and reduce dust concentrations, the Bureau of Mines tested various combinations of operating parameters. Experiments for system efficiency took place in a full- scale model mine at 3.05 m roof height. In general, higher values for scrubber and face airflows resulted in lower dust concentrations. In addition, optimum dust controls would include a face ventilation to scrubber airflow ratio of one. When the airflow ratio was either less than or greater than one, the dust levels in the return and at the operator locations increased. No single dust control technique was the most effective one at all locations due to mutual interaction among techniques.

Jan 1, 1992

By Duane Jorgensen

Two types of factors direct the search for gypsum deposits-geologic factors and economic factors. The prime control and major economic factor is the market for the possible products. The major geologic factor is the control of the depositional environment, which determines whether or not a deposit exists within a given market area. After discovery of a deposit, the distinction between economic and geologic factors is not as clear as before, and the geologic characteristics of the deposit become the economic factors in evaluating the deposit for production and processing. The geologic characteristics are concerned with 1) the gypsum rock, 2) the host or country rock, and 3) geologic fluids, such as gas and water. Prospecting includes both original discovery and the continuing information-gathering period. During this time the above three characteristics of the deposit are determined, usually from core drilling, from phenomena observed during drilling, and from the core and hole. Important information and means of gathering it include sample analyses, sample volume, impurities and their distribution, water levels, aquifer tests, permeability measurements, rock strength tests, rock and overburden thicknesses, rock types, and direct observations of water and gas. Data gathered or inferred from all of these determine the mining or quarrying geometry and environment: which in turn determine the equipment, development, production, and processing costs. Impurities in gypsum deposits are very important in manufacturing processes. The impurities and their effects vary widely from inert minerals with little effect to reactive minerals with strong and mostly detrimental effects.

Jan 1, 1978

By Thierry Coléou

In this paper, we consider open pit optimization. At present, most methods specify the economic parameters and then find the corresponding optimal pit. But as the economic environment varies (which it does regularly these days), the "optimal" pit changes and quite often changes markedly. The questions are: by how much does it change and which parameters are most influential? The functional approach of Technical Parameterization of Reserves, devised by Matheron in 1975, gives the set of all the different optimal pits, under any economic condition. It separates technical design and economic assumptions and thus permits the use of several optimality criteria when choosing the final pit, and not just the maximization of an additive profit formula. Very efficient specific algorithms are presented to obtain all the potentially optimal pits. Fluctuations in the parameters induce changes in the optimum design. Inclusion relations that exist generate very tight bounds and hence very quickly detect optima, even when using a classical adaptation of maximization techniques (graph theory, moving cone, dynamic programming ...). The advantage of Technical Parameterization of Reserves over other methods is that it provides a nested sequence of optimal pits which can then be used for mine scheduling. Many possible mining schedules can be obtained by using the family of technically optimal projects to split up the orebody. The "optimal" schedule, which is in fact a compromise between the different requirements of the economists, the mine planner and the metallurgist, can be chosen from within the wide scope of possibilities. A practical example of mine scheduling for a chromite mine is presented in detail.

Jan 1, 1989

By Dwayne C. Kicker, Duk-Won Park

As the use of longwall mining increases in the U.S.. there is a need to better understand the stress redistribu- tions indicative of this method. To control high stress concentrations, the yield pillar concept has been developed. A physical longwall mine model has been designed to study the effect of yield pillars in deep mining. The model in- cludes sensitive stress measuring devices, a new excavating technique, and a new model material. This study includes the use of both regular and yield pillar systems and has successfully simulated the mode of stress change in chain pillars.

Jan 1, 1986

By S. J. Stokowski

An extensive drilling and laboratory testing program indicates that diagenetic dolomitization of the Oligocene Sombrerito Fm. limestone, southwestern Dominican Republic, is detrimental to the usefulness and quality of the potential construction aggregate resource. The first part of this program was the collection, photographing, and geologic logging of diamond drill cores to allow lithologic subdivision of the strata into potential quarry layers. The primary lithostratigraphic units are: I (youngest) approximately 10 m of white, dense marine limestone; II, approximately 5 m of white, interbedded dense and chalky marine limestone; III, 2+ m of tan, chalky calcitic dolomite. Unit I has been often altered by lateritic weathering and/or dolomitization; Unit II is often altered by dolomitization. The quarry layers were individually crushed, by core, into coarse aggregate sizes for chemical and physical (specific gravity absorption, MgSO4 soundness, sand equivalent, and LA degradation) analyses. The non-weathered units decrease in coarse-aggregate yield and quality with depth and dolomitization. Dolomitization typically causes about 5% lower yield of coarse aggregate, a sand equivalent of about 20 units below the original value, an increase in absorption of about 3%, an increase in the LA of up to 13%, and a decrease in the average 5-cycle MgSO4 soundness by about 17%.

Jan 1, 1987

By Thomas Fliess, Klaus-Christof Ritter, John R. Sturgul

The optimum flow of materials through a smelter is an extremely important phase of the mining cycle. A typical copper smelter will have up to $US 1,000,000 per day of copper being processed. The motion of the overhead cranes in moving the ladles filled with copper matte and slag from furnace to furnace is prescribed but there can be numerous variables to consider. Some of these variables to the system can be: the speed of the overhead cranes, the number of cranes, the size of the ladles, the size of the furnaces, the number of furnaces and the sequence in loading the furnaces. A simulation model was constructed of a working smelter in the SW of the United States. The model has been used to study the effect of varying parameters of the system. The program runs as follows: an input menu appears on the PC screen and the user can navigate through it and change any of the data; the simulation takes place and the results of the simulation sent to a data file. Animation of the system then is shown on the screen in "cartoon" fashion. The software chosen for the simulation was GPSSI H (') and PROOF Professional (') for the animation. The model presented here is believed to be the first reported simulation and animation model for a complete, working smelter.

Jan 1, 1996

By Dao De Xu, Heechan Cho, Mark S. Klima

A study was conducted to determine the feasibility of using dense-medium centrifugation for separating fine (-150 µm) coal. A centrifuge provides the capability of varying the rotational speed and retention time independently, which offers the potential for a higher degree of control as compared to a dense-medium cyclone. Tests were conducted with a 140-mm diameter by 76-mm long Plexiglas separator, which was fitted with appropriate feed and discharge pipes to allow continuous separations to be made. A suspension of ultrafine (-10 µm) magnetite and water was used as the dense medium. The effects of operating conditions, including the magnitude of the 'g"-force and retention time, on centrifuge performance were investigated.

Jan 1, 1995

By A. Shah, L. W. Saperstein, M. C. Radomsky, D. L. Passmore

The development of microcomputer software that provides an analysis of pit-specific accident and production data for the mining industry is seen as a vital component in a total loss-control system. The Mine Injury Reporting System (MIRS) allows users to access accident and production data prepared by the Health and Safety Technology Center of the Mine Safety and Health Administration of the US Department of Labor for any particular state and to generate a simple, yet informative, report.

Jan 1, 1990

By Richard Meriwether Smith

Mining-related earthy bodies in contact with the atmosphere are now counted, generally, as minesoils. Because soils within this broad category are extremely young the influence of parent material is stronger than in older soils, where climate, organisms, and topography have had time to interact with near-surface rocks to form more distinctly differentiated profiles. Understanding of minesoil properties and processes is aided by definitions of rock types in terms of chemical, physical, and mineralogical characteristics that are, with some degree of consistency, translatable into soils. Geological correlations based on age or sedimentary sequences are helpful if they assure details of mineralogy and lithology, but our pedologic objectives demand that any conflicts involving rock types must be resolved in favor of distinctions having strongest implications for soil properties after mining. Chemically this approach emphasizes accounting of potential acid-base status, plant nutrient availability by adapted and calibrated extraction procedures, and absence of biotoxins. Physically it anticipates particle sizes, shapes, and arrangements in readily pervious soil profiles that will favor plant growth with desired levels of moisture and oxygen. Concurrently we are considering soil property suitability for uses other than growth of plants. Above all we need to be able to predict pedogenic processes in the particular environment, including rate as well as direction of chemical and physical change.

Jan 1, 1974

By Dirk van Zyl, Clint Strachan

A study was conducted to assess the feaeibility of increasing the heap height above one lift at the Alligator Ridge Mine. This study concentrated on the physical aspects of the heap and liner performance. Two principle aspects were addressed during this investigation: (a) the adequacy of heap permeability under present and future loading conditions; and (b) the adequacy of the liner to limit seepage losses. Field and laboratory test a were performed and their details and results are presented. It was concluded that the permeability of the heap would remain adequate for higher heap. The geometry of the heap will be the major constraint. It was also concluded that the liner would perform satisfactorily beneath higher heap.

Jan 1, 1987

By Clete Stephan, John Urosek, Ian Anderson

The Endeavour Colliery is operated by Powercoal Pty Ltd. It is located in the Central Coast of New South Wales, Australia. The mine has been in operation for about 30 years, producing around 600,000 tons of export coal annually from two production sections. On June 28. 1995, an explosion occurred underground in the 300 Panel at approximately 9:50 a.m.. There were thirty miners underground at the time of the explosion, all of whom were safely evacuated. From June 29 through July 10, personnel did not enter the mine. However, gas samples of the mine atmosphere were obtained from underground monitoring stations and analyzed. Samples were also obtained from boreholes that were drilled from an adjacent mine. On July 10, the atmosphere at the underground monitoring locations and at the boreholes appeared stable with minimal risk of combustion occurring underground. Plans were developed to begin the recovery of the underground workings. The recovery of the underground workings was completed on July 13. The underground investigation of the explosion began on July 14. The investigation was conducted by the New South Wales Department of Mineral Resources. Technical assistance was pro- vided by the United States Department of Labor's Mine Safety and Health Administration (MSHA).

Jan 1, 1997

By Paul E. Senseny

Data from triaxial compression tests per- formed at confining pressures between 0 and 100 MPa are used to evaluate parameters in a contitutive model that is based on microcracking. The tensorial formulation is reduced to equations that are specific to the simple Loading imposed in triaxial compression tests. Procedures for evaluating the model parameters are described, dependence of parameter values on confining pressure is discussed, and prediction of failure is assessed.

Jan 1, 1986

By Stanley M. Miller

Analysis of discontinuous rock masses for engineering design purposes requires information about fracture characteristics. For such studies, fractures or other elements of the rock fabric (bedding, foliation, etc.) should be considered in a statistical manner because they generally have high frequencies of occurrence and are discontinuous over the design area. A practical design procedure includes defining structural domains as those areas which contain fractures with similar orientation patterns. Within a structural domain, the statistical distributions of fracture set characteristics (spacing, fracture density, dip, dip direction, etc.) may be computed from mapped data and then used to quantitatively describe the rock fabric. These distributions can then be randomly sampled (using Monte Carlo techniques) to simulate the rock fabric and to help define potential failure surfaces along fractures. 1 The prediction of failure geometries is an essential part of stability analyses used in designing rock slopes or underground openings. In current probabilistic design procedures, Monte Carlo techniques that rely upon the iterative generation and analysis of deterministic instability models do not incorporate spatial aspects of the random variation in fracture set characteristics, 1,2 but consider the characteristics to be spatially independent.

Jan 1, 1979

By D. W. Park

The Longwall Strata-Control and Maintenance System (LoSCo-MS) is a software and data-communication system developed at the University of Alabama. This system integrates real-time shield monitoring, data presentation, analysis and the forecasting of forthcoming events. The main objective of this system is to provide stability information on longwall panels, including excessive shield load, low setting pressure, leg leakage, poor shield performance and imminent maintenance problems. Analyses of various mining and geological parameters were also performed to determine past and present roof characteristics and to forecast roof loading patterns for the following mining cycles, the next periodic weighting, etc. A local coal mine in the Warrior Coal Basin has adopted this system to provide daily evaluation of ground stability and maintenance problems in their longwall panels. Two years of experience with this system is covered in this paper.

Jan 1, 2000

By R. L. Grayson, S. Yuan

A goal-programming-based, worker-scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model, the accomplishment of each regular and non-regular job is a goal, and the objective is minimization of the deviations from the goals. A number of coefficients are employed as premultipliers of the decision variables to address practical considerations associated with the utilization of workers and the requirements of jobs. This model is applied to a 41-worker problem.

Jan 1, 1992

By Dwight R. Coles

The solving of complex metallurgical flowsheet calculations by hand is, at best, a tedious job which often proves that engineers, too, make mistakes. The high cost and long lead time associated with manual flowsheet solutions have led several organizations involved in research, development and construction of extractive metallurgical processes to search for computerized systems which will solve flowsheet calculations. Although design flowsheet programs have been developed by the chemical industry, the ability to solve flowsheets involving particulate solids is usually overlooked. A new computer applications system has been developed at Fluor Mining and Metals which has been designed to accommodate the type of design flowsheets required by the minerals industry. By employing the sequential modular computation technique, a library of metallurgical pro- cessing routines may' be accumulated which are used by a universal executive system. This technique enables rapid solution of new process) .flow- sheets with only a minimum of additional programming effort. The implementation of the FLEXMET flowsheet solution system is the subject of this paper. Some of the major features of the system which are examined include interactive input data handling, automated flowsheet calculation order arrangement, flexible accomodation of unit operations models and advanced management of recycle and specification control calculations.

Jan 1, 1982

By Irwin R. Higgins, Joseph C. Milbourne

The selection of a suitable nitrate removal process depends on a variety of site-specific chemical and environmental issues. The dominant technologies for nitrate removal include biological denitrification and continuous countercurrent ion exchange. The decision to apply either of these technologies, or both together, depends on the nature of the waste water to be treated. Factors that affect the selection of the biological system include the feed composition and feed temperature. Ion exchange nitrate removal systems ere less sensitive to the feed composition but require disposal or destruction of the concentrated pregnant eluate. The paper discusses Tetra's continuous countercurrent ion exchange technology (CCIX™) and fixed film biological reactor, Denite®. The treatment of the ion exchange pregnant eluant is also discussed.

Jan 1, 1995

By M. Girardeau, J. Blondin, M. Nomine

It is well known that surface moisture and fine content have a strong influence on coal handle- ability. It is known as well that these two criteria are not sufficient to classify coals. It seems that certain types of coals are intrinsically difficult to handle, the reason being still not well understood. For these coals, moisture and fine content are aggravating factors and have to be strictly controlled in order to avoid handling problems (sticking, arching in hoppers.. .). CERCHAR has undertaken research aimed at identifying the role of intrinsic characteristics of coal with regard to handling properties. Two of them have been identified as particularly relevant : the clay content and the "colloidal particle" content. Two simple tests commonly used for soils characterisation, but never used so far for coal, have been applied to characterise a wide range of coals. The derived classification has been compared with an empirical classification based on dry screening tests. DRY SCREENING EXPERIMENTS Dry screening at a relatively low screen aperture (e.g. 6 mm) may be considered as a good tool for assessing the handleability of wet fine coals. Difficult to handle coals always lead to rapid plugging of the screen whilst easy to handle coals can be screened without difficulties. A wide range of coals has been selected with various ash, moisture and fine content. Their characteristics are given in table 1. The experimental set-up consists of a 2 t.p.h vibrating screen equipped with two automatic re- cording balances collecting respectively oversize and undersize material. Provided that the feeding rate is accurately controlled, good reproducibility in the percentage passing as a function of time is obtained. Figure 1 gives examples of different types of relations that were obtained. - LMC coal exhibits a behaviour that is characteristic of easy to handle coals : % passing remains constant in the course of the screening operation. - B coal behaves slightly differently. One observe first a rapid decrease in the flow passing through the screen and then a stabilization. Hand- ling properties can be considered as intermediately - The curve relative to LHB coal is characteristic of a very difficult to handle coal that blinds the screen almost immediately. It is necessary to point out the fact that the classification derived from screening experiments is a global one, including not only intrinsic factors but also external factors such as fines and moisture content. The role of surface moisture is in particular very important and variations in this parameter may upset the empirical classification

Jan 1, 1988