Search Documents

By H. Maleki, G. Tetreault

This study was initiated by the US Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room- and-pillar mining using a continuous miner (CM) was economically sound or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets " are left in longwall mines on one side of the mains near outcrops and adverse geological conditions or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included the analysis of the geologic, geotechnical and economic factors that influence the recovery of small coal reserves; the analysis of historic changes in supply, demand and coal prices; the development of typical cost models for room-and-pillar and longwall mines; and the development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR), as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modern longwall mines and, thus, is used to evaluate the increased costs associated with adding new development sections for extraction of small reserves. The study examines the economic feasibility of using unconventional longwalls for the recovery of medium-sized reserves, depending on site-specific geologic and geometric conditions.

Jan 1, 2002

By Arnolfo A. Valdivia

Prior to 1971, there were several clinical trials to evaluate programs for early detection of lung cancer. Among these, the Philadelphia Pulmonary Neoplasm Research Project,(3) the Veterans Administration Study published by Lilienfeld,(7) and the controlled trial of the Kaiser Foundation Health Plan showed an overall five year survival rate of 8% for newly detected cases (the same as the national statistic for unscreened patients). In 1971, the National Cancer Institute initiated three randomized, controlled mortality studies using lung cancer screening of persons at high risk (male smokers over 45 years old). The studies are being conducted at the Johns Hopkins University Hospital, the Mayo Clinic, and the Memorial Sloan-Kettering Cancer Center. The studies have slightly different designs in the combination of sputum cytology and chest x-rays. At the Mayo Clinic the study group is offered screening with sputum cytology and chest x-rays every four months, whereas the control group is advised to have an x-ray and cytology every year. No reminders are sent, and it is believed that only about 20% of the control group is screened. At Johns Hopkins and Memorial, both experimental and control groups are offered annual chest x-rays. The experimental group is additionally offered sputum cytology every four months.(5) At present all of the programs show that screening can detect cancers that are undetectible by other means. However, at this time mortality rates in the control and experimental groups are not significantly different in any of the three studies. OUR PROGRAM Our clinic is located in Grants, New Mexico and we provide most of the pre-employment physical examinations for the mines operating in the Grants area (Kerr McGee Nuclear, Homestake Mining, United Nuclear, Western Nuclear, and Ranchers). In the examinations, we obtain the previous mining history of the worker, a chest x-ray, a sample of sputum for cytological examination, and a blood sample. We also provide routine annual physical examinations of the workers, with special interest in the detection of bronchogenic carcinoma. In the early seventies, we did not have a definite surveillance program. We did not know whether we should have a program like the one started at Memorial or like the one started at the Mayo Clinic. After long consideration, we decided to have a program that does not demand a sputum cytology and chest x-ray every four months, but that allows as many chest x-rays and sputum cytologies as needed to diagnose lung cancer as early as possible. We believe that, if a screening method for cancer is to be optimally effective, it must detect the process at stages early enough for curative therapy. We order a test depending on the age of the miner, the race, the mining history, the smoking history, the radiation exposure levels, and the results of the previous chest x-ray and sputum cytology. With the help of the computer, we have a list of all the miners who should be watched closely because of age, race, mining history, smoking history, radiation exposure, etc. Examination of the miners is performed at our clinic, where all the records are kept. The sputum is collected there but examined in Grand Junction, Colorado, by Dr. Geno Saccomanno. There are two ways to collect sputum. The best way is to collect three consecutive morning samples. For this, we need the cooperation of the miners. They have to follow these instructions and mail the bottle containing the sample to Grand Junction. "Instructions for obtaining a good cough specimen" The enclosed plastic bottle contains a preservative solution, so do not empty out the liquid in it. When you go to bed, place the plastic bottle at your bedside where it will be handy in the morning. When you first get up in the morning (before breakfast) try to cough up some "phlegm" from deep in your chest, and spit it into the liquid in the bottle. Try coughing several times. If you have difficulty coughing, try inhaling deeply the steam from a teakettle (or home-type inhalator). Keep the amount of saliva (ordinary spit) that you put into the bottle along with the cough specimen as small as possible. Do not collect the "phlegm" or mucous that comes from the back of your nose. Put the cap back on the bottle, and shake it vigorously for two minutes. If the amount of material you have coughed up is quite small, then keep the bottle at your bedside for three or four days, and each morning try to add another cough specimen. After obtaining your cough specimen, repack the bottle in the mailing container, and attach the enclosed mailing label. It does not require any postage stamps. Unfortunately, some miners "forget" to mail the sample and end up with an incomplete physical examination. To avoid this some companies, like Homestake, request that we obtain the sample in our clinic by forcing cough and expectorant with a nebulizer machine. This method does not give as good a sputum sample as the previous one, but we do get a sputum sample for every miner. The policies of different companies, in regard to annual physical examinations are different. All

Jan 1, 1981

By Jozef Descour, Kazunori Nishioka, David M. Neil

Designers, engineers, and contractors are using three-dimensional seismic tomography for geotechnical site investigations and during tunnel excavation for hard rock and soft ground applications. Utilizing multiple types of seismic signals produced by a TBM, drill, or impact breaker, the reflection of different velocity features are processed into a holographic image of the actual structure to be encountered. The Mill Creek Phase 3 alignment in Cleveland, Ohio, was imaged to define existing conditions along a 1,200-ft section of a proposed 6.1-m (20-ft) diameter CSO tunnel and, specifically, a zone of expected anomalous conditions where drilling was inconclusive. In Japan, Kajima Corporation used TRT™ to image a number of tunnels including the Fujikawa and Kanaya tunnels in a combination of methods to map structural features along the alignment.

Jan 1, 2001

By D. R. Nagaraj

The chemistry and structure-activity relationships for four new classes of sulfide mineral and precious metals collectors developed recently are discussed in this paper. These collector classes are alkoxycarbonyl alkyl thionocarbamates and thioureas, dialkyl (or diaryl) monothiophosphates and dialkyl monothiophosphinates. The main emphasis will be to highlight the differences between collectors and their affinities for various minerals on the basis of data on kinetics of adsorption on pure minerals, natural ore flotation and microscopy of flotation concentrates. The mechanism of interaction of these collectors with sulfide minerals is also discussed with the available data on the FTIR and solution chemistry studies.

Jan 1, 1989

By B. J. Arnold, F. F. Aplan

Prior laboratory work has demonstrated that much of the fine ash forming minerals entering a flotation froth are there as a result of water carryover- from the bulk contents of the flotation cell (Arnold and Aplan, 1986a). Using a bank of four 8.5 m3 (300 cu ft) Wemco flotation cells cleaning a well-liberated Lower Kittanning seam coal, test results show that the sulfur and ash content of the froth is directly related to the water content of the froth (or inversely related to the percent solids in the froth). Reagent changes that result in a watery froth produce a higher ash content in the froth. A direct comparison of laboratory and plant results show that the standard laboratory flotation test produces a product higher in sulfur and ash than that produced in the plant. Caution should be exercised when extrapolating laboratory test results to the plant situation. A method of estimating coal flotation product quality in the plant based on laboratory tests is given.

Jan 1, 1991

By W. J. Schlittler

Auxiliary Equipment pumping systems to support primary, secondary and regrind grinding circuits will be the primary focus of this paper. Every grinding system is unique and requires special design considerations for proper application of pumps to transport mill discharge. To satisfy the majority of applications, a new series of pumps has been developed by Svedala, known as World Class Pumps. Selection of these newly developed pumps for each type of grinding circuit will be presented. Specific components of selection are materials of construction, piping system, classification method, material characteristics and slurry characteristics. Both horizontal and vertical pump applications will be reviewed with emphasis on rules of pump piping and sump design.

Jan 1, 1999

By William Gleason

"Once the primary fuel source for the United States and the economic backbone for communities from Appalachia to Wyoming, coal has been on a steady decline since the mid 1990s, and is now at the center of political debate in the United States.The political spectrum of the United States is divided on the future of coal and its place in the energy sector. The coal mining industry and the communities that rely on coal have increasingly been pitted against forces that wish to regulate coal to the history books.In 2008, President Obama launched what many have called his war on coal, and during his eight years in office, he pushed through numerous pieces of regulations and legislation and that he said were aimed at reducing carbon emissions, but that others viewed as direct assaults on the domestic coal industry. Obama led the United States delegation to Paris to sign the Paris Accord in 2016, a 196-country agreement pledging that the United States would do its part to reduce carbon emissions. His administration also instituted clean air, power and water regulations that added extra environmental burdens to many industries, but perhaps none more so than the coal industry.In this month’s lead feature, “A study of U.S. coal mine closures since 1994” (page 18), the impact of the war on coal, and other factors, can be seen in text and figures. Author Jacob Brinkman and coauthors Jay Schafler and Catherine Johnson scoured the data of the U.S. Energy Information Administration (EIA) and the U.S. Mine Safety and Health Administration (MSHA) to show how coal production and mines have been impacted since 1994 and how the years 1994 to 2000 and 2008 to 2016 were particularly hard on the industry.For example, in 1994 there were 2,354 coal mines in the United States. Currently, there are 1,035 mines in operation.In 2016, then candidate Donald Trump promised to end the war on coal and to put coal miners back to work. In 2017, President Trump has followed up on those promises. He announced plans to withdraw the United States from the Paris Accord, signed an executive order designed to undo the Clean Power Plan put in place by President Obama, halted the research on the health effects of mountaintop removal coal mining, directed the U.S. Environmental Protection Agency (EPA) to revise the guidelines of waste water from power plants and has touted that more than 1,000 coal miners have returned to work since he was elected."

Jan 9, 2017

By D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Jan 1, 1997

By E. Wiewiorowski

A new technology for recovery of metals from spent catalysts containing aluminum, cobalt, molybdenum, nickel and vanadium was developed. The catalysts are decomposed in two consecutive pressure leaching steps. Sodium aluminate-sodium hydroxide systems are lixiviants in both leaching steps. Selective extraction of molybdenum and vanadium is achieved in the first leaching step. The leach liquor is processed for separation and recovery of these two metals. The residue from the first leaching step is further processed in a second leaching step where alumina is solubilized. The residue from this operation is a nickel-cobalt concentrate. Alumina is separated from the second stage leach liquor by precipitation; the depleted liquor, a sodium aluminate solution, is recycled to the first and second leaching step. This technology has advantages over other approaches for the recovery of metals from spent catalysts because no solid waste is generated.

Jan 1, 1988

By D. Royston

Curved pulp lifters have been incorporated in SAG and AG mills in Australia. The aims have been to ensure complete discharge, at high throughput, of both slurry and coarse solids, especially at high mill rotational speeds. Curved pulp lifters can overcome incomplete discharge and back-flow of solids down the pulp lifter that can occur in straight-radial pulp lifters (and is a major cause of wear). They can be designed to prevent reverse flow of pulp via grates back into the mill. Experience with curved pulp lifters now extends to three years over three mills, in one mill as an installation from new and two as retro-fitted installations. Curved pulp lifters, relative to conventional designs, offer improved discharge and wear performance and well as high impact-resistance and wear life of the curved pulp lifter grates.

Jan 1, 2000

By Roy M. Fleming

During the decade of the 1970's, a new emphasis was placed on assuring a safe and healthful workplace for all American workers. Much of the basis for this national effort was federal legislation: the Occupational Safety and Health Act of 1970 and the Federal Mine Safety and Health Act of 1977 (amended from the 1969 Coal Mine Act). One of the agencies involved in this protection effort is the National Institute for Occupational Safety and Health (NIOSH) of the Centers for Disease Control (CDC) in the Department of Health and Human Services (DHHS). In fulfilling its mandates under the 1970 and 1977 Acts, NIOSH conducts research, experiments, and demonstrations to support and stimulate advancements in health and safety practices. Priorities for NIOSH research are established primarily through congressional mandates, requests from the Department of Labor, needs as defined by NIOSH researchers, and surveillance information. Emphasis is placed on research in the areas of toxicology, industrial hygiene, physical and chemical sciences, physiology, ergonomics, engineering, psychology (behavior and motivation), and epidemiology (industry-wide studies). The framework of the current Institute program to identify, evaluate, and control occupational hazards includes activities in surveillance, research, evaluation, and training. These activities are planned and evaluated through a system that coordinates the efforts of eight research and scientific divisions. Each division develops projects to address program areas that have been identified by NIOSH management as having highest priority. In surveillance programs, the objectives are to identify substances and agents found in a representative sample of workplaces and to collect and evaluate information on rates of disease and injury in occupational groups. Information is also collected on occupational safety and health programs implemented by industry. Estimates of worker exposures and the potential for adverse health effects are considered in setting priorities for further investigations. A related activity, which also serves to provide technical assistance to industry, is NIOSH's Health Hazard Evaluation program. On-site investigations of workplaces are made in response to worker, employer, or government agency requests. Both industrial hygiene and medical examinations are conducted, and the results contribute to identifying new problems and evaluating their significance which may have public health implications beyond the particular worksites that are investigated. Field and laboratory research projects are performed to meet several objectives: - Characterize the working environment by evaluating current and past exposure levels for workers who are included in epidemiological or medical investigations. - Develop epidemiological information to define the association between the substance or agent under investigation and the acute and chronic health effects on workers. - Determine through animal studies the parameters of an association between exposure and effect. - Investigate the etiology of disease. - Develop sampling and analytical instruments and techniques and demonstrate their application for measuring toxic materials in the workplace. - Formulate sampling strategies that will accurately and precisely indicate exposure levels. - Develop medical procedures to prevent disease and to detect the presence of disease and early indicators of disease. - Assess the technology for control of exposures, including engineering and administrative techniques, personal protective equipment, and work practices. Presently, the research program is focused on reproductive effects, neurotoxic effects, injury/trauma, lung disorders, cutaneous disorders, cardiovascular disorders, cancer, stress-related disorders, effects of physical agents, digestive disorders, and renal and other organic disorders. In studying these issues, priorities are determined by the seriousness of possible adverse health effects resulting from occupational exposures, the feasibility of studying existing records or obtaining new data, and the size of the population which is potentially affected. Where there is low level of suspicion concerning adverse health effects or where an occupational disease occurs in a variety of industrial environments, investigations are limited to gross analyses of health effects such as review of mortality patterns. In such studies, the industrial populations selected are those for which existing data resources can be utilized. Such data consists of records of occupational exposures or health status which have been maintained by the employer, the union, or Government agencies. Where a review of the available information suggests that serious health hazards exist and the existing data resources are inadequate for quantifying the relationship between the specific biological response and type and degree of exposure, prospective studies are initiated. Information derived from such research is essential for the development of sound criteria for control of industrial exposures to noxious agents. Other input to the criteria documentation process comes from searching and evaluating the literature. Criteria documents contain the recommendation of an environmental limit where information is available to support it, as well as the recommendation of work practice controls, medical evaluation, information for workers to recognize and avoid the hazard, and identification of specific research gaps. In some cases, during the criteria document preparation, gaps in knowledge are found which necessitate further research before an occupational standard can be recommended.

Jan 1, 1981

By E. W. Hawk

he power generation industry may be required to reduce carbon dioxide (C02) emissions if regulations related to global climate change are enacted. Coal-fired generation emits more than 80% of the power sector CO2 and would be a likely target for CO2 reductions. Compliance with the Kyoto Protocol will require a 33% reduction from the projected year 2012 emission level, even with moderate load growth. This article describes an analysis of power industry CO2 reduction options and their costs. It assesses how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered. The Global Climate Change Treaty signed at the Rio de Janiero Earth Summit in June 1992 set the long-term goal of stabilizing CO2 concentration in the atmosphere. The December 1997 Kyoto Protocol established short-term mandatory targets for the United States and 37 other developed countries. The United States' target is a 7% decrease by 2012 from the 1990 "greenhouse gas" level. Developing countries are exempted from reductions, according to the Kyoto Protocol, despite projections that indicate a significant increase in their emission levels. The Kyoto Protocol must be ratified by the US Senate. US power industry carbon emissions were 490 Mt (540 million st) in 1990 and are projected to be 680 Mt (749 million st) in 2012, according to the US Energy Information Administration. Coal-fired generation emits more than 80% of the power sector CO2. Assuming that the power industry is only required to reduce emissions by a proportional share, a 33% emission reduction, or 225 Mt (248 million st) of carbon, would be required to comply with

Jan 1, 1999

By Yong Pan, SRIVATSAN JAYARAMAN SRIDHARAN, Purushotham Tukkaraja

The block cave mining method poses unique ventilation challenges compared to other underground metal mining methods. This research study focuses on assessing the airflow behavior in regulated airflow distribution systems by developing a 1:100 scaled block cave experimental model and a numerical model. This study also investigated gas flow behavior under various airflow conditions. Based on our findings, we observed that reduction in particle size and porosity of caved materials, decrease in cave footprint, and closure of undercut drifts would increase cave airflow resistance. The increased airflow is found to be beneficial for gas dilution regardless of its source locations, while the regulated airflow distribution system might deteriorate the gas dilution situation when the source is located in the extraction drifts.

Sep 1, 2022

By A. J. Nugent

Investigations were undertaken to evaluate peroxygen compounds for effective­ness in alkaline cyanide leaching of gold. The addition of peroxygens improved the leach results. Calcium peroxide was the best performed reagent to be employed. Improved reagent consumption followed the trend of calcium peroxide> hydrogen peroxide> no peroxygen addition. In general, preaeration stages could be eliminated, and improved leach rates achieved with no detrimental impact on leach perfor­mance. Interox has not developed an Au Plus (Trade Mark pending) system to utilise this new leach reagent. Initial plant trials are verifying its potential to give additional benefits.

Jan 1, 1990

By A. Kaczmarek

As the mining industry is enjoying a much needed and long awaited increase in demand for natural resources, consolidations in both the mining and mining service industries and a generational departure of experienced industry professionals is challenging today’s mining companies, not only in maintaining their existing operations, but also in securing qualified resources for developing new projects. These challenges are compounded for junior mining companies, oftentimes lacking in operating properties to draw from for experienced professionals and having to compete with the majors’ “mega-projects” for experienced project personnel from the reduced ranks of engineering companies. This paper discusses some strategies developed by Anatolia Minerals Development Limited in developing its Çöpler Gold Project in central Turkey.

Jan 1, 2006

By Alexander N. Winchell

"The waters of Lake Superior flow into those of Lake Huron through the St. Mary's river. The rapids in this river are about half a mile wide and three-quarters of a mile long, in which distance the fall amounts to about twenty feet. Since this was the only obstacle to navigation between the west end of Lake Superior and ports on any of the other Great Lakes except Ontario, attempts were made many years ago to permit the passage of small boats from Lake Huron to Lake Superior by means of canals and locks. The first canal was built on the Canadian side of the river by the Northwest Fur Company in 1797-98. The lock was 38 feet long, 8 feet 9 inches wide and had a lift of 9 feet. A tow path was made along the shores for oxen to track the bateaux and canoes through the upper part of the rapids., The lock was destroyed during the war of 1812 by United States troops from Mackinac Island.The first ship canal, known as the State Canal, was built on the American side of the river in 1853-55, about 750,000 acres of land in Michigan having been granted by congress to a private company as a 'concession for its construction. This canal was more than a mile long, 65 feet wide at the bottom and 100 feet wide at the water's surface. It had two locks, each 350 feet long by 70 feet wide, with a lift of about 9 feet. The depth of water in the canal was about 13 feet and in the locks about 11 1/2 feet."

Jan 1, 1920

By H. Janas

In a gas/coal outburst the gas plays an active, driving part. The proneness of coal to outbursts can be determined by means of its gas emission properties, since coal that is liable to outbursts differs from coal with normal gas emission properties in that it liberates its gas from the sorptive bond more quickly. There is a risk of outburst when the flow of metha¬ne originally desorbed by the coal is sufficient to move the loosened coal which has been broken suddenly. The violence of a gas/coal outburst can be evaluated from the distance of projection of the mass of coal. It depends on the gas pressure and on the liability to outburst of the coal at the original centre of the outburst. Both factors are complementary in their effects so that the same work is done in a gas/coal outburst when there is a high gas pressure and low proneness to outburst as when there is a low gas pressure and a higher proneness to outburst. The gas pressure in the coal increases with its gas content. Consequently it is possible to deduce the gas pressure of a coal seam from its gas content. In the Federal Republic of Germany the risk of a gas/coal outburst is thought to exist when the desorbable gas content of the coal reaches or exceeds the value of 9 m3/ton and if the specific limit value of the proneness to outburst is exeeded. The Mine Ventilation Testing Station of the Westfalische Berggewerkschaftskasse has developed a new method for determining the risk of gas outbursts immediately after taking the samples at the coal face (1), (2).

Jan 1, 1980

By M. P. Murphy

The state of Illinois is committed to direct support of the Illinois coal industry. The Illinois Department of Commerce and Community Affairs’(DCCA) Office of Coal Development (OCD) provides incentive programs for coal and energy development. Illinois coal programs include tax and financing incentives for new coal-fired generation, infrastructure grants to expand coal mining and transportation systems, research and development grants to initiate and advance clean-coal technologies and demonstration grants to bring advanced coal utilization technologies to commercial-scale readiness. As a result of these efforts, the Illinois coal industry is reinventing itself and is now more productive and competitive than ever before.

Jan 1, 2003

By B. Stewart, J. R. Warneke

The productivity of underground mines has increased dramatically since the introduction of continuous miners. A variety of new hazards have developed as a result. In the spring of 2004, Mine Health and Safety Administration (MSHA) held a workshop to brainstorm ideas to decrease the number of injuries associated with continuous miners. One of the main areas of discussion at the workshop was “trailing cable-handling injuries.” The method of handling the power cables over the years has changed very little while the technology and uses of continuous miners has advanced dramatically. This paper will discuss the main ideas brainstormed at the MSHA continuous miner (CM) trailing cable handling workshop and the history and root causes of cable-handling injuries, as well as proposed ideas developed at the National Institute for Occupational Safety and Health (NIOSH) to alleviate some of the cable handling issues.

Jan 1, 2006

By S. Mertikas

The purpose of this paper is to set the stage for (1) the determination of the specifications and actions required for a successful development of a system for the management of waste deposits and contaminants resulting from activities in the mineral industries and landfills and (2) the appropriate infrastructure to be developed at the industrial level. The design of this system would be such that its application could be extended to other industries as well. Waste deposits and contaminants from activities in the mineral industries and landfills commonly cause damage to the environment. In addition to precautionary measures aiming to protect against environmental impact, early warning and immediate response to mining hazards and contaminants is a requirement for sustainable development. Hazard detection and control requires continuous and real-time detection techniques, as well as methods for tracing and predicting the motion of contaminants and waste products. The efficient accomplishment of these goals in the minerals industry requires developing an integrated system for environmental monitoring using remote sensing technologies, in combination with advanced image analysis and geostatistical techniques.

Jan 1, 2003