Search Documents

By Howard M. Cotton

Early in 1977, Amoco Production Company and Houston Chemicals, a subsidiary of Pittsburg Plate Glass (PPG) Industries, started producing iodine commercially in northwestern Oklahoma. This is significant because it is the first plant in over 40 years to be built in the United States with iodine as its sole commercial product. With the exception of a limited amount of iodine produced by Dow Chemical in Michigan, the United States is dependent upon imports from Chile and Japan for its iodine needs. The two million pounds of iodine produced annually from the Woodward plant will supply over one-third of the United States' requirements. Routine analysis of subsurface brines by the Formation Water Lab at the Amoco Production Company Research Center in Tulsa, Oklahoma, revealed unusually high concentrations of certain potentially economic minerals. Investigations determined that, of the minerals in question, iodine appeared to offer the best potential. The brines in question are located in the Morrow sands (basal Pennsylvanian) at a depth of 7,175 to 7.400 feet, in an area where Amoco has been active in a gas play for the past 20 years. The regional iodine concentration ranges from 10 to 700 ppm and averages around 300 ppm with the project area. The project is located 8 miles north and slightly east of the town of Woodward, where the well-developed, porous, and permeable sands of the Woodward trench contain large volumes of brine.

Jan 1, 1978

By Arthur S. Cornford

According to Arbiter (Reference 1), the ball mill was invented by Brückner in Germany in 1876 and was first used in the United States on ores about 1905. The basic concept was a simple rotating cylindrical drum in which the tumbling action of the charge of material and grinding media resulted in size reduction of the material. Despite the very low mechanical efficiency of this method a number of factors have caused the tumbling mill to remain, by far, the most widely used piece of equipment for mineral grinding. The principal factors influencing this situation have been simplicity of design, ease of manufacture, ready adaptability to familiar material handling layouts and the absence of practical alternatives acceptable to the industry. In the early mills, the material was ground in batches, the mills being charged and discharged through doors in the shell. The shell was supported by means of solid trunnion shafts resting in plain bearings and the drive was accomplished through one of these shafts. In some later batch mills, the mill shell was supported on rollers which were also used to drive the mill. At an early stage, continuous operation was made possible by feeding and discharging the mill through hollow trunnions, the method still in most widespread use. The mechanical and structural design of the early mills was not an onerous engineering task. Norse sense and good practical knowledge were key qualifications. The mill shells had to be heavy enough to withstand the physical abuse they would receive in the field and the bearings had to have low enough unit pressures and sufficient wear retol to ensure several months of operation before the need for replacement occurred. When these requirements were satisfied, stresses developed in the equipment during operation were insignificant and the majority of structural failures were probably due to the use of inferior materials in manufacture. Over the years, the ever present demand for increased productivity has resulted in a steady Increase in the size of units of production equipment, including grinding mills. Arguments have been presented elsewhere, for and against the Idea of a high throughput single line grinding operation as opposed

Jan 1, 1972

By Adrian Brown

The primary method of slope stabilization is ground water-control. Recent research has established the properties which slope materials must exhibit in order for stabilization measures to be feasible, but there is little guidance in the literature about suitable field tests to develop the parameters needed for this evaluation. This paper presents a proven method for large scale testing which allows an evaluation of the feasibility of ground water pressure control in a reasonable cost and time frame. Methods of performance and analysis of the test are presented, and the method is illustrated by reference to case examples.

Jan 1, 1984

By B. A. Bancroft

A quality assurance program consists of all those activities aimed at providing confidence to the purchaser that the suppliers quality system will provide a product that will satisfy the purchaser's stated quality requirement. An organizing principle is necessary for prioritizing the quality control activities of quality personnel in the face of a myriad of technical possibilities, data-analytic applications, and an overwhelming number of possible activities promoted in the literature and by quality "gurus". The organizing principle I like is that quality assurance exists when those involved in the quality process: (1) know what they are supposed to do, (2) can tell if they are doing it and are set up to continue doing it and, (3) if they are not, they can remedy the situation in a timely fashion. Any incremental activity which facilitates this organizing principle is a continuous improvement activity. That activity which has the chance to facilitate this principle to the greatest extent is the next one to work on. In these days of lean corporate and regional staffs it is as important to know what not to work on as it is to know what to work on. In this paper I shall discuss in general terms the implications of this organizing principle for the design of Quality Assurance (QA) Programs for coal mines and also provide some comments about the application of Statistical Process Control (SPC) methodologies in the coal industry.

Jan 1, 1994

By J. Libaude

The Changement mine in French Guyana has, since 1983, processed gold ore by classical gravity methods. A large part of the gold is in the form of very small, free or enclosed grains. Recovery by gravity methods is thus limited (25-30%) and the present plant produces about 40,000 t annually of auriferous waste assaying about 6 git. The company therefore decided to retreat the waste by heap cyanidation. After laboratory tests which showed the feasibility of the method, a pilot test was set up on site. An experimental 3000 t heap, composed of waste of 0-8 mm grain size, was laid out by bucket loader on an impermeable pad covered by PVC and geotextile cloth. The upper layer of the heap was reworked by mechanical shovel to break up the area that had been compacted by the passage of the loader so as to restore adequate permeability.

Jan 1, 1998

By Fred W. Stuart

Microprocessor technology has revolutionized the business community by placing tremendous computing power in the hands of the end-user for a very inexpensive price tag. The range of applications covers process control, to office automation, to personal computing capabilities. With the influx of this new technology, which these systems have to offer, also comes some unique operational and control considerations. But before we address these items, let us lay a foundation of common terms to be used throughout this presentation. Due to the rapid advances in microprocessor technology, where a new generation of computers is announced every two or three years, it becomes difficult to define a microprocessor system and have it valid for an extended period of time! Therefore, for this presentation, we will be dealing with a subset of microprocessors called Personal Computers or PC's. At the heart of a PC is a Central Processing Unit or CPU. The CPU performs the actual program and command execution. The programs dealing with driving the various peripheral equipment is referred to as the Operating System (for example: DOS : Disk Operating System, CP/M - Control Program/Microcomputers, etc.). The CPU is normally housed in an enclosure which contains power regulators, peripheral equipment interfacing 'cards', and expansion 'slots' to enlarge the capabilities of the PC system.

Jan 1, 1989

By H. Soto

As a follow-up to a laboratory study, a pilot scale column for the flotation of coarse particles was designed and then tested in two different applications. In the first test, the concentration of a coarse phosphate ore (normally beneficiated by skin flotation in spirals) was carried out in a flotation plant in Florida. In the second pilot test, the column was used as a scavenger cell in the coarse flotation section of a potash beneficiation plant in Saskatchewan, Canada. Particle size of the phosphate feed was of the order of 0.6-1.0 mm and the potash feed 1-3 mm. The column was 1 feet diameter and was fed at rates between 0.5 to 1.4 tph. The effect of operating variables such as air and water flow rates, bubble size, frother concentration, residence time, sparger, etc were evaluated. The most important factors in column performance were found to be bubble size, air flow rate and the thickness of the froth bed. Best results were obtained in the absence of a froth bed, with low air flow rates and with small bubbles. The paper presents comparative performance and discusses details of the column design. Phosphate recoveries in the column were better than 90% whereas the conventional skin flotation circuit normally yields about 60% recovery for a comparable concentrate grade. Potash recovery from the tailings of the conventional flotation circuit was as high as 42% recovery. Particle size distribution of the potash concentrate was coarse enough to meet requirements for potash fertilizer.

Jan 1, 1993

By M. P. Oommen

This paper provides a brief look at a proposed short-longwall for coal, development. The proposed method is an attempt to realize the advantages of longwall mining in deposits that, historically, would only be minable by continuous mining methods. An overview of the proposed layout, development requirements, production rate, ventilation scheme and other associated features is provided. This mining method could help operators in above-drainage seams where minable areas are smaller. It may also have application in areas that are peppered with gas wells and in environmentally sensitive areas which preclude the use of conventional longwalls.

Jan 1, 1993

By Randhir S. Sehgal

After some decades of lying low and being treated as a second rate fuel, coal is back in the news. Production is rising. Predictions are for an ever expanding use, and they differ only in their rates of increase. Even the FBI is involved in trying to stop fraudulent sales of non-existent coal lands and leases to the innocent. In short, we have a nearly chaotic boom on our hands. Obviously our energy production base is in the process of undergoing a major shift, and the process will present many problems. However, there is little doubt that the industry has the basic strength and organization to be able to deal with the new issues that will arise as a result of these shifts in production and use of coal. After all, it does produce nearly 800 M tpy now, and coal is the single biggest fuel for generation of electricity. This role of coal is illustrated in the table below, which shows the coal equivalent quantities of various fuels used in the production of electricity.

Jan 1, 1980

By Clement K. Chase, Manuel Lastra, George M. Potter

Heap leaching for gold-silver recovery in the western United States has been widely applied. Advantages, disadvantages, and requirements of the method are discussed, as well as heap building, recovery systems, agglomeration applications, and safeguards against freezing. A list and review of current heap leach operations world-wide are presented, together with obvious opportunities for application of this innovative technique in new areas.

Jan 1, 1983

By R. E. Gertsch

A mobile-modular carbon adsorption mill design and operation for small to medium sized heap leach precious metal mines is presented. In the mobile-modular strategy, charcoal columns with adsorbed metal move from small strategically located carbon adsorption loading stations to a central stripping facility and back. The design has many advantages: 1) It scales-up from pilot plant to full production. 2) It has low capital requirements. 3) Operational costs are competitive with other systems. 4) Mill production can react quickly to changes in ore grade or property area. 5) The solution circuits are simple and easy to maintain. 6) Charcoal damage is reduced.

Jan 1, 1993

By T. E. Bernard

"Refuge alternatives (RA) provide shelter to miners trapped underground during a disaster. RA manufacturers must demonstrate that their RAs meet the Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and the management of heat that results from the RA occupants and mechanical/chemical systems. In this study, miner size and activity level were used to determine the metabolic heat rate, oxygen requirements, and carbon dioxide generation that is representative of miners in a refuge situation. A convenience sample of 198 male miners was used for the distribution of current US coal miners, and the composite 95th percentile height and weight were determined to be 193 cm (76 in) and 133 kg (293 lb). The resting metabolic rate (RMR) was determined to be representative of activity level in an RA. The highest likely metabolic heat generation ranged from 115 W to 135 W, depending on RA occupancy. The highest required oxygen supply and carbon dioxide removal were estimated to be 23 LO2/h/person (0.81 ft3/h/person) and 20 LCO2/h/person (0.71 ft3/h/person), which means the margin of safety is 50% or more when compared to the MSHA requirements. INTRODUCTION Refuge alternatives (RAs) provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their RAs meet Mine Safety and Health Administration (MSHA) requirements for the supply of oxygen, the removal of carbon dioxide, and the management of heat that results from the occupants and the mechanical/chemical systems in the RA [1]. These MSHA requirements were based on a standard 70 kg (168 lb) male with an assumed allocation of activity of 80% rest and 20% moderate activity level [2]. The purpose of this paper is to re-examine the metabolic heat generation and oxygen and carbon dioxide requirements of miners in an RA based on actual miner size and more realistic RA activity levels based on current RA designs. The purpose of this paper is to re-examine the Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and heat generation. To achieve this, researchers took the following steps to estimate the metabolic demands and the associated heat generation, oxygen requirements, and carbon dioxide production. 1. Characterized the anthropometric characteristics of the miner population. 2. Described the metabolic rate profile of RA occupants. 3. Characterized the maintenance demands of RAs. 4. Summarized oxygen supply and carbon dioxide removal volumes. ANTHROPOMETRIC CHARACTERISTICS OF MINERS The weight, height, and age distributions of the adult male populations are summarized in Table 1. For each data set, the reported mean and standard deviation are provided. The 95th percentile (%ile) value for height and weight for each population was the mean plus 1.64 times the standard deviation."

Jan 1, 2017

By L. Yuan, C. Brown, N. Rayyan, J. Soles, T. H. Dubaniewicz

As lithium-ion batteries (LIBs) become more prevalent in the mining industry, new hazards of battery fire and explosion are emerging. Efforts must be taken to ensure that workers are safe from these new hazards, such as batteries undergoing thermal runaway in underground areas that may have explosive methane-air mixtures. Researchers at the National Institute for Occupational Safety and Health (NIOSH) investigated overpressures generated within a sealed battery enclosure filled with an explosive methane-air mixture and a single cell lithium-ion battery driven into thermal runaway using an accelerating rate calorimeter (ARC). For both iron phosphate (LFP) and nickel manganese cobalt (NMC) lithium-ion cells, the explosion overpressures remained unchanged with varying percentages of methane concentration in the atmosphere surrounding the cell. It’s likely that the gases released from the battery undergoing thermal runaway caused an inert atmosphere within the sealed canister. The results from this study will help mining equipment manufacturers develop proper measures to keep miners safe while working with lithium-ion batteries in underground gassy mines

Mar 2, 2022

By William E. Mead

The process of selecting a building site for a major structure is a complex procedure involving the consideration of a multitude of factors. The approximate geographic location for a structure is usually fixed by its intended function, though often there may be several site alternatives. Socio-economic, logistic, marketing and political factors are the primary site determinants. Also critical in site planning, however, are the environmental factors, both natural and man-made. These factors will influence the precise siting location within the limits allowed by the primary determinants and will dictate some of the basic design criteria. This paper discusses environmental factors, principally those which are natural conditions, that must be analyzed for five different groups of structures. The importance of thorough site environmental analysis based upon the principles of applied earth science is described. Significant elements to be considered in an appraisal of the geology, hydrology, seismology and meteorology are outlined.

Jan 1, 1968

By K. E. Hjelmstad

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air, rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine, fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage.

Jan 1, 1989

By P. Bissert, L. Yan, D. Yantek

"Federal regulations require refuge alternatives (RAs) in underground coal mines to sustain life for 96 hours while maintaining an apparent temperature (AT) below 35°C (95°F). NIOSH research has shown that heat and humidity buildup is a major concern with RAs because they have a limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding an RA is very complex and is not easily defined analytically nor experimentally. To investigate heat and humidity buildup in RAs, NIOSH conducted multiple in-mine 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA. The test results show that when moisture was introduced into the tests to represent perspiration and respiration from miners (wet tests), the average measured internal air temperature at midheight increased by 7.7°C, 9.4°C, and 10.5°C, and the RH approached 95%, 94%, and 88%, respectively. For the dry tests when no moisture was introduced, the average internal temperature increased by 8.4°C, 10.3°C, and 12.6°C, respectively. INTRODUCTION If an accident occurs in an underground coal mine, miners who cannot escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the thermal environment inside the RA. The metabolic heat of the occupants and the heat released by the CO2 scrubbing system will cause the interior air temperature to increase. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The internal thermal conditions can subject miners to heat stress, which can lead to heat exhaustion, heat stroke, or even death depending on duration and magnitude of exposure. MSHA regulations require that RAs must be designed to ensure that the internal apparent temperature does not exceed 35°C (95°F) when the RA is fully occupied [1]. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and wind speed. It is used to assess the perception of indoor temperatures when workplaces are not sufficiently heated, cooled, or insulated to provide comfortable or healthy conditions. Before a mobile RA can be deployed at an underground mine for emergency usage, it must be tested to show that its internal AT when fully occupied will not exceed the 35°C (95°F) limit. For practical reasons, RA manufacturers usually conduct their tests at above-ground test facilities. To investigate RA thermal response in an in-mine environment, NIOSH conducted multiple 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA in its underground coal mine facility. The work described in this paper could be used by RA manufacturers to determine a final temperature rise based solely on dry and time-reduced testing."

Jan 1, 2017

By Kousik Sinha

The advantage of using a clean coal as a feedstock in a direct liquefaction plant is improved performance of the plant by several factors e.g., increased throughput of coal; reduced wear and tear of valves, pipes, and pumps; increased liquid yields, etc. This paper examines the technical feasibility for cleaning Illinois #6 coal as a feedstock to a direct coal liquefaction plant via selective agglomeration using a coal-derived heavy distillate, Wilsonville V-1074 as agglomerant. Effects of addition of Kerosene or coal-derived Naphtha as conditioner, coal particle size, slurry pH, oil to coal ratio, and operating temperature on ash reduction and clean coal weight recovery have been studied. Results show that about 70% of the ash can be removed from this coal and the clean coal weight recovery over 85% can be achieved by using this technique with suitable selection of coal particle size, slurry pH, mixing intensity and oil to coal ratio.

Jan 1, 1991

By J. E. Hoffman, Massimo Maccagni, T. J. Keefe, Marco Olper, O&apos

The research laboratory of B.U.S Engitec has identified and patented a new process for electrolytic production of lead from lead sulphide concentrates with simultaneous production of elementary sulphur. The process occurs in an aqueous solution, at atmospheric pressure, utilizing a solution of ferric fluoroborate in fluoroboric acid as the oxidizing and solubilizing medium for lead sulphide. After the filtration and separation of a residue composed of elementary sulphur and the gangue which accompanied the concentrate, the solution containing lead as fluoroborate and iron reduced to a ferrous state is sent to a diaphragm electrolytic cell where, in the cathode compartment, the lead is deposited in a compact form on the stainless steel permanent blank. The exhaust solution stripped of lead is sent to the anode compartment where the oxidation of ferrous fluoroborate into ferric fluoroboratetakes place, reproducing the oxidizing solution for new leaching. Depending on operating conditions, it is possible to selectively solubilize the lead from the other metal values present in the concentrate. The sulphur produced from the reaction may be separated from the gangue by extraction with solvent or by flotation.

Jan 1, 1993

By Corale L. Brierley

The depressed economic condition resulting from normal cyclic behavior, a more fundamental structural alteration, or both, is a mandate for change within the mining industry. Although several strategies for change have been proposed, the option of applying high technology processes to this smokestack industry offers the greatest opportunity for regaining global competitiveness and a new vitality. Research and development to secure new technologies require a corporate commitment for substantive change, a tech¬nologically enlightened management, a well¬funded and stable science and engineering effort, and a dedicated and motivated technical team--features in short supply in the mining industry today. However, an alternative to in-house development of frontier technologies is available to this beleagured industry through entrepreneurial, high-tech companies. These entities, with their dedicated focus toward product development, motivated and streamlined teams, high productivity and efficiency, and low costs offer a unique opportunity for large corporations to obtain high-tech products and services. These commodities are available through traditional commercial channels and an array of creative business arrangements. The latter offers notable benefits to large companies including windows on frontier technologies and mitigation of risk. Likewise, entrepreneurial companies profit through manufacturing and marketing relationships and an expanded financial base.

Jan 1, 1985

By Allen M. Newcome

The Ohio valley division of consolidation coal company has incorporated two new aspects within its coal mining concern. A new communication system, thru the cooperation of the c. & p. Telephone company, has been established in each of our mines with its central control in the general office building. In conjunction with this system, a Texas instruments 960 a computer has been incorporated into the system. The purpose for our computer is to provide modernization and improvement to our safety, production and maintenance programs. Thru proper use, the computer will help eliminate inaccuracies and inefficiences that have previously caused inaccurate analysis of problems. Due to federal requirements for more reliable communications in underground mines, Ohio valley division is making a concentrated effort to improve its communication systems. Systems such as the magneto phone and trolley phone have been looked at more critically. It was found that these systems are being used well beyond their limits. With these facts in mind, division personnel started looking for a system that would have these built in advantages: ease of maintenance and installation, increased reliability, low cost, and an inherent ability as a multiple use system.

Jan 1, 1975